Texas Instruments EVMK2E Quick Start Manual

EVMK2E Evaluation Module

Quick Start Guide

©2014 Texas Instruments Incorporated

EVMK2E Evaluation Module

No Functionality

A

1 press: safe shutdown of SOC;
2 presses within 0.5sec: warm reset;

B

3 presses within 0.5sec: full reset;
4 presses within 0.5sec: cancel reset

C

On board XDS200 USB

COM1 : SoC UART Console

D

USB control of both SOC COM1 & BMC COM2

E

F

JTAG(MIPI-60) connector for SoC

G

COM2 : BMC UART Console

BMC Reset : Resets the microcontroller

H

and will reset the entire board

Dip switch for boot configuration :
1111 : No Boot mode/JTAG DSP Little Endian

I

0010 : NOR SPI ARM Master Boot

USB3 PORT 1(Device and HOST Modes)

J

USB3 PORT 0(HOST only)

K

©2014 Texas Instruments Incorporated

Two boot procedures are described below, one for Uboot and one

for CCS.

1) Uboot Steps:

1

For Windows User:

Insert pendrive and load USB
COM drive by executing the
program\drivers\
CP210xVCPInstaller_x86

For 64-bit systems execute the

program\drivers\

For Linux User:

Please download driver from any of below link as per Linux kernel version on PC.
Compile the driver and install it.

http://www.silabs.com/Support%20Documents/Software/Linux_3.x.x_VCP_Driver_Source.zip

http://www.silabs.com/Support%20Documents/Software/Linux_2.6.x_VCP_Driver_Source.zip

2

Ensure EVM configuration

switches are set as shown for

NOR SPI Boot.

3

Connect the USB mini-B

cable to J1

©2014 Texas Instruments Incorporated

4

Open Tera Term,

select COM port, configure

settings, as shown in image.

This serial port settings of

Tera Term is shown as an

example. It is not mandatory

to use only Tera Term as

a serial terminal

5

Insert DC-in cable to apply
12V power.

6

On SoC serial port console
a display will be seen,
as shown in image.
Hit any key to stop

auto-boot when prompted.
EVM is now ready for
Uboot applications.

MCSDK Downlink Page:

http://software-dl.ti.com/sdoemb/sdoemb_public_sw/mcsdk/latest/index_FDS.html

©2014 Texas Instruments Incorporated

2) CCS Steps:

1

Update or install CCS
(V5.5.0.00077 or later) from

MCSDK download page.

2

Ensure EVM configuration
switch are set as shown for
No Boot/JTAG DSP Little
Endian Boot mode.

3

Connect the USB mini-B

cable to XDS200.

44

Insert DCInsert DC--in cable to apply in cable to apply
12V power.12V power.

55

LaunchLaunch CCSCCS.. After CCS is After CCS is
opened, opened, EVM is now reaEVM is now readydy
for use.for use.

©2014 Texas Instruments Incorporated

Getting Started:

Please see the ‘Getting Started’ chapter in the
MCSDK User Guide for hardware and
software setup:

http://processors.wiki.ti.com/index.php/MCSDK_
User_Guide_for_KeyStone_II.

Important Notes when handling the EVM:

Plug in all the cables before powering

ON the EVM to ensure proper
grounding.

Do not unnecessarily flex the boards,

while inserting cables. Excessive
flexing can break the PCB traces.

Use proper ESD procedures when

handling the EVM.

Warning: Some components on the

EVM may be too hot to touch with your
bare hand when power is on.

Online Documentation

TI device product page

http://www.ti.com/product/66ak2e05

Multicore SDK

http://www.ti.com/tool/bioslinuxmcsdk
http://processors.wiki.ti.com/index.php/M
CSDK_User_Guide_for_KeyStone_II

CCS v5

http://processors.wiki.ti.com/index.php/Categ
ory:Code_Composer _Studio_v5

C663X EVM Information:

https://www.einfochips.com/tI-66ak2e-evm

This link contains:

Hardware & Software details
User Guide
Technical Reference Manual

EVMK2E EVM Support:

Please write to [e-mail]
for technical queries related to this EVM.

eInfochips Address:

eInfochips Limited.
303,Parishram Building,5/B Rashmi Society
Mithakhali Six Road,Navarangpura.
Ahmedabad- 380009.

Gujarat, INDIA.
Tel : [phone].
Fax :[phone].

http://www.einfochips.com/

TI Worldwide Technical Support

Internet

TI Semiconductor Product Information Center Home Page
support.ti.com
TI Semiconductor KnowledgeBase Home page
support.ti.com/sc/knowledgebase

Product Information Centers

Americas

Phone [phone] Fax [phone]
Internet/Email support.ti.com/sc/pic/americas.htm

Europe, Middle East and Africa

Phone

European Free Call 00800-ASK-TEXAS

(00800 275 83927)
International [phone]
Russian Support [phone]

Note: The European Free Call (Toll Free) number is not active in
all countries. If you have technical difficulty calling the free call
number, please use the international number above.

Fax +(49) (0) 8161 80 2045
Internet support.ti.com/sc/pic/euro.htm

Japan

Fax

International [phone]
Domestic 0120-81-0036

Internet/Email

International support.ti.com/sc/pic/japan.htm
Domestic www.tij.co.jp/pic

Asia

Phone
International [phone]­Domestic Toll-Free-Number Toll-Free-Number
Australia 800-999-084 Malaysia 1-800-80-3973
China 800-820-8682 New Zealand 0800-446-934
Hong Kong 800-96-5941 Philippines 1-800-765-7404
India 1-800-425-7888 Singapore 800-886-1028
Indonesia 001-803-8861-1006 Taiwan 0800-006800
Korea 080-551-2804 Thailand 001-800-886-0010

Fax [phone] Email [e-mail]

[e-mail]

Internet support.ti.com/sc/pic/asia.htm

Important Notice: The products and services of Texas
Instruments Incorporated and its subsidiaries described herein
are sold subject to TI's standard terms and conditions of sale.
Customers are advised to obtain the most current and complete
information about TI products and services before placing
orders. TI assumes no liability for applications assistance,
customer's applications or product designs, software
performance, or infringement of patents. The publication of
information regarding any other company's products or services
does not constitute TI's approval, warranty or endorsement
thereof.

The floating bar is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners

©2014 Texas Instruments Incorporated

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Texas Instruments:
XEVMK2EX EVMK2EX