Texas Instruments 2510EM User Manual

Web sites: www.ti.com/lprf
E2E Forum: www.ti.com/lprf-forum

Make sure to subscribe to the Low-Power RF
Newsletter to receive information about updates to
documentation, new product releases and more. Sign
up on the TI web pages.

1. Kit Contents

2 x CC2510EM
2 x Pulse W1010 2.4GHz antennas

The boards in this kit are FCC and IC
certified and are tested to comply with
ETSI/R&TTE over temperatures from 0 to
+35°C.

FCC/IC Regulatory Compliance
FCC Part 15 Class A Compliant
IC ICES-003 Class A Compliant

2. How to use the modules

The EMK is an add-on kit to supplement the
CC2510DK with evaluation boards supporting
additional frequency bands.

The CC2510EM boards can be plugged into several
development boards from Texas Instruments. Most
notably, you can use the SmartRF04EB, which is
included in the CC2510-CC2511DK. This board lets
you run a packet error rate (PER) test, control the
device from SmartRF™ Studio and it can be used as
a development platform.

It is also possible to plug the EM into the
SmartRF05EB or the “SoC Battery Board”. The
SmartRF05EB, or the SoC BB together with the CC
Debugger, will provide a complete development
environment for the CC2510. See:

http://www.ti.com/tool/soc-bb

This guide will show how to use the modules
together with SmartRF04EB.

3. Plug EM into EB

Insert a CC2510EM into both SmartRF04EBs. Make
sure the antenna is firmly connected to the SMA
connector.

Caution! The kit contains ESD sensitive
components. Handle with care to prevent
permanent damage. To minimize risk of
injury, avoid touching components during
operation if symbolized as hot.

4a. Battery power

There are three different ways of applying
power to the EB:

The first method involves using a battery,
either a 9V or a 4xAA battery pack
connected to the battery connector on the
bottom side of the board

Warning! To minimize risk of personal injury
or property damage, never use rechargeable
batteries to power the board.

4b. DC power

The second method applies DC power using the DC
input jack (right in picture, centre is +, sleeve is
ground), or by connecting a 4-10V voltage source
between the 4-10V and 0V terminals of the power
connector (left in picture). It is also possible to
connect a 3.3V voltage source between the 3.3V and
0V terminals. The on-board voltage regulators will be
bypassed in this case.

External Power Supply1 Requirements:
Nom Voltage: 6 VDC
Max Current: 800 mA
Efficiency Level V

4c. USB power

The EB can also be powered from the USB bus.
Make sure that the SmartRF™ Studio software is
installed before connecting the EB to the PC;
otherwise you may experience problems in installing
it later due to driver issues.

Note that if multiple power sources are connected,
the source with the highest voltage will power the
EB. This means that you should disconnect any

attached battery when using a lab supply or USB
power; otherwise the battery will be drained.

5. Set power switch

If a 3.3V source is used as described in 4b
above, the switch should be set to the
leftmost position. For all other cases, the
switch should be set to the rightmost
position. This switch can be used to turn off
the EB by switching it to the opposite
position of that used to turn it on

Do not leave the board powered when
unattended.

6. Packet error rate test

When power is applied to the board, the test
program will start. You should see the Chipcon logo
with chip name and revision number as shown
above on the LCD display on both EBs. Pushing
button S1 in the lower right corner of the board will
show the first menu item.

7. Select Frequency

Select the frequency that you want to use (2420
MHz, 2440 MHz, 2460 MHz or 2480 MHz). Move the
joystick up or down to display the choices and push
button S1 in the lower right corner of the board to
select the displayed frequency.

1

CC2510EMK Quick Start Guide

Opening the box an running the Packet Error Rate Test on SmartRF04EB

September 2013

safety certification requirements such as UL, CSA, VDE, CCC, and PSE

When using an external power supply, make sure it meets the listed requirements in addition to complying with applicable regional product regulatory and

September 2013

Web sites: www.ti.com/lprf
E2E Forum: www.ti.com/lprf-forum

Make sure to subscribe to the Low-Power RF
Newsletter to receive information about updates to
documentation, new product releases and more. Sign
up on the TI web pages.

8. Select Data Rate

Select which data rate to use (10 kbps, 250 kbps
or 500 kbps) by moving the joystick. Confirm
your choice by pushing button S1.

9. EB 1: Select Receiver

Select Receiver on the first EB by moving the
joystick. Confirm by pressing button S1. The
Receiving node will display “Ready to receive”.

10. EB 2: Select Transmitter

Select Transmitter on the other EB by moving the
joystick upward. Confirm by pressing button S1.

11. EB 2: Number of packets

On the transmitter EB, select the number of
packets to send. More packets take longer, but
give a better statistical result. Confirm by
pressing button S1.

12. PER Test (Transmitter)

Press S1 button again to start transmitting the
packet burst. The transmitter will show a running
counter that shows the number of packets sent.

13. PER Test (Receiver)

The receiver will show the total accumulated packet
error rate (PER) together with the average signal
strength (RSSI) of the previous 32 received
packets. A symbol in the upper right corner will
blink for every 32nd incoming packet to indicate
whether the link is maintained.

14. Per Test results

When the PER test is completed, the result will
be displayed on the receiver until a new test is
started. A new test can be started from the
transmitter.

15. References

Please visit www.ti.com and

http://www.ti.com/tool/cc2510emk

For more information about how to use the
CC2510EM, download the CC2510-CC2511DK

User Manual, the SmartRF™ Studio PC Tool,

software examples, as well as datasheets,
reference designs and application notes.

You will also find a lot of information on the TI E2E
forum at http://e2e.ti.com

We hope that you will enjoy working with the
CC2510 device.

16. Troubleshooting

It you are experiencing problems with this test,
please check the following:

a. The data rate affects the obtainable link range.
b. The source code for the packet error rate test

application is available on the web. You may
modify the source code to test at other
frequencies or data rates.

c. See “DN300 -- SmartRF04EB Troubleshooting”

for general troubleshooting of your EB board.

1. Download and Install

Before connecting SmartRF04EB to your PC,
download SmartRF Studio from

www.ti.com/smartrfstudio.

2. Launch SmartRF Studio

After installing the tool, connect the EB to the PC
using the USB cable and start SmartRF Studio.

Select the “2.4 GHz” tab and double click the

CC2510 device icon.

3. Configure the Radio

You can now configure the radio, run tests,
export register settings and run link tests with
another CC2510 on a SmartRF04EB connected
to the PC.

SmartRF™ Studio