Telex PW24ND User Manual

Revision

A

Page 1 of 10

6/24/09

2.4GHZ WIRELESS SYSTEM FOR
POLICE VIDEO RECORDING

USER GUIDE

Revision

A

Page 2 of 10

6/24/09

TABLE OF CONTENTS

1.

Quick S

et Up and Operation

.......................................................

3

2.

Component Details

.......................................................................

5

3.

Installation

....................................................................................

6

4.

Guidelines For Best Performance

................................................

7

5.

Troubleshooting Guide

................................................................

.8

6.

Technical Specifications

...............................................................

9

7.

Service

and Warranty

...................................................................10

8.

Components and Accessories

.....................................................10

Revision

A

Page 3 of 10

6/24/09

QUICK SET UP AND OPERATION

Synching Up The

Transmitter

and Base

The synch operation only needs to be performed
the first time a system is used, or a new bodypack is used with a base previously synched to
ano

ther bodypack. Do not perform the synch operation multiple

times;

it

only needs to

be done one time

when

a new bodypack is used with a new base.

1) Make certain the Master/Slave switch on the side of the transmitter is in the
Master (M) position.

2) Turn the tr

ansmitter power switch to ON and place the transmitter in the
recharge cradle of the base. The transmitter goes in the base with the
beltclip facing out.

3) The recharge LED will light (Green if

fully charged, Red if charging). Leave

the transmitter in the cradle for 4 hours for a full charge.

3) Press the In-Use button on the transmitter and hold

for 5 seconds (or until

you hear beeps if the beep is enabled to confirm synch), then

release the

button.

4) The transmitter and base are now synched and will continue t

o be until

another transmitter is linked to that

base

.

Normal Operation

1) With the transmitter synched up, remove it from the cradle, plug in the lapel
microphone (if used) and place the transmitter on your belt.

2) To start the recording, press the In-Use but

ton and the In-Use LED will light a

constant green and you will h

ear

a short beep

or feel a short vibration.

3) To end recording, press the In-Use button and the In-Use LED will turn off
and you will hear a short beep

or feel a vibration

.

4) At the end of your s

hift turn the transmitter off and replace it in the charging

cradle

.

Two Transmitter Operation on One Base

1) If one of the transmitters to be used with the base is already set to Master
and syn

ched to the base, skip to step 5

.

2) Set the Master/Slave switch

on one of the transmitters to Master (M)

, put the

BEEP switch to BEEP

and turn

the

power switch to ON

. Then

place the

transmitter in the recharge cradle of the base.

3) Press the In-Use button on the transmitter and hold

for 5 seconds

or until

you

hear a beep, then release the button.

4) The Master transmitter is now

synched to the base.

5) On the second transmitter, place the Master/Slave switch in the Slave (S)
position.

6) Turn on the power and place the BEEP switch to BEEP and place the
transmitter in the recharge

cradle.

7) Press and hold the In-Use button for 5 seconds or until you hear a beep.

8) Both transmitters are now ready for use with this base.

The master
transmitter will control the video trigger relay and either will be able to trigger
the Emergency relay.

Low Battery Warning

1) If the transmitter Low BATT indicator (red) starts flashing or you hear warning
beeps

(or vibrations)

, return the transmitter to its cradle on the receiver to

fully charge the transmitter.

2) The Charge LED indicator will light constant

green when the unit is fully

charged.