Telematrix DECT MWD5, DECT MWD, DECT 2MWD, DECT 2MWD5 Programming & Installation Manual

$%#4'(Z#ORDLESS3ERIES
$%#4-7$s$%#4-7$s$%#4-7$s$%#4-7$
0ROGRAMMING)NSTALLATION15)#+'5)$%
1.800.462.9446 domestic
+1.719.638.8821 international
www.telematrixusa.com
Parts/Items Check List:
The following parts are included in this package: A. (2) Line cords - 15 ft./4.5m. B. Battery for Handset C. Base unit D. Mobile Handset E. Paper faceplate F. Protective plastic faceplate overlay G. Pass-Through Power Adaptor
The following are optional Items possibly included: (Must be ordered separately) H. Charging Stations & Handset with Handset Battery and Power Adaptor. Please call TeleMatrix to order : +1.719.638.8821 worldwide voice
Charging the Handset Battery: (On Base and Charging Station)
The handset Battery is a Ni-Cd battery. This battery requires a Full charge prior to use to ensure long life. To charge the battery, complete the installation procedure by plugging the power source into the wall outlet and the telephone base or charging station.
Install the battery the battery per below instructions, lining up (+) & (-) on battery to (+) & (-) on battery compartment. Press into place, then replace cover and place handset into base (face down) or charging station (either facing front or back).
Installing Battery Into Handset:
1. Open cover with small screwdriver. Do Not open more than 1/2 inch.
2. Grip handset and depress cover at hinged end.
3. Slide cover off, exposing battery compartment.
4. Line up (+) & (-) on battery with (+) & (-) on inside of battery compartment.
5. Slide battery into battery compartment. Do Not
Force Battery!
6. Press on back end of battery to snap into place.
7. Place hinged end of cover into slot, then press down and snap into place.
V: 10.30.07
Handset Battery...
DECT 6.0 & 1.8GHz Series Features:
• Line Powered - Single & Two Line Telephones
• DECT Non-Interference cordless technology
• SteelTrap memory technology (EEPROM)
• TouchLite one-touch message waiting retrieval
DECT Base:
1. Industrial grade construction, smooth plastic finish
2. Speaker (half duplex)
3. Message Waiting selector switch (submerged) (LR1 LR2 TYPE)
4. Programmable Store key. (submerged) (used to program location in speed dial keys)
5. Programmable Flash key.(submerged) (100mS to 1000mS timed line break, Default is 600mS)
6. Line Cord receptacle (top end of phone) 7a. HSIA (High Speed Internet Access) receptacle incoming from wall (top end of phone) 7b. PassPort® HSIA (High Speed Internet Access) receptacle outgoing to guest laptop
8. Faceplate & Plastic Overlay display area (full-length, 4-color printing possible)
9. Base Ringer Volume switch - LOW or HI settings on Line 1 and Line 2
10. Guest Services Memory keys (10 or 5 keys) (store up to 32 digits maximum)
11. Programmable Pause/Redial key (submerged) (programmable for1.0 to 5.0 second pause) 12a. ADA Compliant Speaker Volume key (up) (8-step control) 12b. ADA Compliant Speaker Volume key (down) (8-step control)
13. Handset Locate key with audio indication
14. Base Microphone
15. Speaker key with No/Off LED indication
16. Mute key with On/Off LED indication
17. TouchLite™ Message Waiting key with 1-touch retrieval bright red color, blinks when message waiting. 18a. Line 1 with LED indication 18b. Line 2 with LED indication
19. Electronic HOLD key with On/Off indication and remote release
20. Dial Pad - (On-hook dialing possible with Memory keys and when Speaker key is activated)
21. Interchangeable handset cradle (provides for special accent colors to light ash or black telephones)
22. Handset Charging location (handset Must be face down to charge)
23. In Use - Ringer indication light
24. Charging Indication light
25. Desi strip display area
Handset:
26. Cordless Handset with programmable “Handshake” technology - Handset can be synchronized with base with a few simple steps.
27. Message Waiting Indicator, blinks when message is waiting.
28. ADA Compliant Handset Speaker
29. Handset Faceplate & Plastic Overlay
30. Handset Ringer Volume switch LOW or HI settings
31. Line Selector key - Line 2 On/Off with LED indication
32. Hold / Conf. Handset key, and remote release
33. Line Selector key - Line 1 On/Off with LED indication
34. Handset Dial Pad ( Press and Hold Key “1” to retrieve messages from TouchLite.
35. Last Number Redial key 36a. Handset Volume Up (8-Step) 36b. Handset Volume Down (8-Step)
37. Flash key
38. Charging Location Contacts (Handset must be face down to charge in base unit. Handset will charge regardless of direction set into charging station unit.)
1
23 19 18a18b 17 16 15
13
12b
12a
11
10
8
7b
7a65432
24
20
26
35
36a
34
29
33
32
31
30
2827
37
36b
38
38
9
14
21
22
25
Telephone Underside:
39. Base underside sticker information: Certification - FCC, CE, ETL, RoHS Version label Model name REN number Disposal label QC label Series number Warranty Void If Seal Broken label
40. Voltage Settings - 24V, 48V & OFF for Line 1 & Line 2. (factory set at 24V) Line Voltage 24-52VDC (+/-) Line Current 15mA to 80mA Ringer Equivalance - 0.6B
41. Non-Slip rubber feet (4)
Cordless Handset Charging Station:
42. Message Waiting indicator
43. Cordless Handset
44. Handset Pop-Off Cover for battery compartment.
45. Interchangeable Accent Piece, to match custom cradle color # 21.
46. AC Power Plug-In. (back of stand)
47. Battery Charging & Synchronization programming indicator light.
48. Cordless Handset Charging Stand. Handset will charge regardless of whether it is placed with either front or back showing.
49
50
Power Adaptor:
49. Phone Line from wall goes into Line receptacles.
50. Line to Phone from Adaptor.
3940 41
42
43
46
45
44
47
48
Connecting the Line Cord - # 6 & # 49/50
Be sure your power adaptor is specified for your region of the world prior to plugging into the wall socket
Registering DECT Handset with a Specific Base Unit:
1. Remove DECT handset from base unit cradle.
2. Press and Hold Down the LOCATE button # 13 on the base for approximately 10 second.
3. When the button has been held down long enough, the “Charge” indicator - on the base unit begins to blink # 24 (even though there isn’t a handset in the cradle).
4. While the charging indicator is blinking, place the handset Face Down, into the base unit cradle.
5. When the blink indicator light turns off (stops blinking), this handset is registered.
6. You may now place the handset into a charging station, or use as the base handset.
7. Repeat steps 1 - 5 to register additional handsets. Note: You may have three (3) charging stations handsets and one (1) base unit handsets
synced up to each base unit, a total of four (4) cordless DECT handsets per suite.
Storing a Number Into Memory Keys # 10 or TouchLite key # 17
Each location can store up to 32 digits in tone mode.
Note: A “Pause” or “Flash” programmed into memory counts as one digit when storing a number.
1. Press the Speakerphone ON/OFF key to activate telephone - # 15.
2. Press the STORE Key - # 4.
3. Enter the number to be stored using the numeric dial pad.
4. Press the desired memory location wherein the number is to be stored.
5. If additional numbers are to be stored, repeat steps 3 thru 5.
6. Press Skeaper key to end this programming phase.
Programming Flash Timing & Pause Timing
Flash timing options are 100mS thru 1000mS, programmable in 100mS increments. The default Flash timing is 600mS. Pause timing options are 1.0 sec. thru 5.0 seconds. The default Pause timing is 3.6 sec.
1. Press the Speakerphone ON/OFF key to activate the telephone - # 15.
2. Press the “Store” key once - # 4.
3. Program “Flash” by pressing “1” for 100mS, “2” for 200mS, etc.... # 5 & 13
4. Exit programming by pressing Speaker key again.
To program Pause follow the above sets, except at # 3 - do the following:
3. Programming “Pause” by pressing “1” for 1.0 sec., “2” for 2.0 sec., etc... # 11
Storing “Pause/Redial” Into Memory - Pause # 11
If you are using your telephone anywhere that requires an access code for outside calls, you may need to add a “Pause” to the number to allow time for the outside line to connect. You can enter an many pauses as needed.
Note: a “Pause” or “Flash” programmed into memory counts as one digit when storing a number.
1. Press Speakerphone ON/OFF key.
2. Press the STORE Key - # 4.
3. Enter the required access code using the dial pad.
4. Press the “Pause” key.
5. Enter the digits to be stored using the numeric dial pad.
6. Press the desired memory location wherein the number is to be stored.
7. If additional numbers are to be stored, repeat steps 3 thru 7.
8. Press Speaker key again to end this programming phase.
Flash” hook function - Flash # 5 & # 13
The Flash function is used to access PBX features or Telco line features such as Call Waiting. The Flash function is a 600mS timed line break. If the Flash function will be used often, store the feature into memory located for easy access as follows:
1. Press Speakerphone ON/OFF key, then press the “Store” key.
2. Press the “Flash” Key - # 5 & # 13.
3. Press the memory location wherein the “Flash” is to be stored.
4. Press Speaker key to end this programming phase.
Connecting...
Programming...
Syncing Handsets...
Programming...
$%#4'(Z#ORDLESS3ERIES
$%#4-7$s$%#4-7$s$%#4-7$s$%#4-7$
0ROGRAMMING)NSTALLATION15)#+'5)$%
Parts/Items Check List:
The following parts are included in this package: A. (2) Line cords - 15 ft./4.5m. B. Battery for Handset C. Base unit D. Mobile Handset E. Paper faceplate F. Protective plastic faceplate overlay G. Pass-Through Power Adaptor
The following are optional Items possibly included: (Must be ordered separately) H. Charging Stations & Handset with Handset Battery and Power Adaptor. Please call TeleMatrix to order : +1.719.638.8821 worldwide voice
Registering DECT Handset with a Specific Base Unit:
1. Remove DECT handset from base unit cradle.
2. Press and Hold Down the LOCATE button # 13 on the base for approximately 10 second.
3. When the button has been held down long enough, the “Charge” indicator - on the base unit begins to blink # 24 (even though there isn’t a handset in the cradle).
4. While the charging indicator is blinking, place the handset Face Down, into the base unit cradle.
5. When the blink indicator light turns off (stops blinking), this handset is registered.
6. You may now place the handset into a charging station, or use as the base handset.
7. Repeat steps 1 - 5 to register additional handsets. Note: You may have three (3) charging stations handsets and one (1) base unit handsets
synced up to each base unit, a total of four (4) cordless DECT handsets per suite.
Charging the Handset Battery: (On Base and Charging Station)
The handset Battery is a Ni-Cd battery. This battery requires a Full charge prior to use to ensure long life. To charge the battery, complete the installation procedure by plugging the power source into the wall outlet and the telephone base or charging station.
Install the battery the battery per below instructions, lining up (+) & (-) on battery to (+) & (-) on battery compartment. Press into place, then replace cover and place handset into base (face down) or charging station (either facing front or back).
Installing Battery Into Handset:
1. Open cover with small screwdriver. Do Not open more than 1/2 inch.
2. Grip handset and depress cover at hinged end.
3. Slide cover off, exposing battery compartment.
4. Line up (+) & (-) on battery with (+) & (-) on inside of battery compartment.
5. Slide battery into battery compartment. Do Not
Force Battery!
6. Press on back end of battery to snap into place.
7. Place hinged end of cover into slot, then press down and snap into place.
Storing “Pause/Redial” Into Memory - Pause # 11
If you are using your telephone anywhere that requires an access code for outside calls, you may need to add a “Pause” to the number to allow time for the outside line to connect. You can enter an many pauses as needed.
Note: a “Pause” or “Flash” programmed into memory counts as one digit when storing a number.
1. Press Speakerphone ON/OFF key.
2. Press the STORE Key - # 4.
3. Enter the required access code using the dial pad.
4. Press the “Pause” key.
5. Enter the digits to be stored using the numeric dial pad.
6. Press the desired memory location wherein the number is to be stored.
7. If additional numbers are to be stored, repeat steps 3 thru 7.
8. Press Speaker key again to end this programming phase.
“Flash” hook function - Flash # 5 & # 13
The Flash function is used to access PBX features or Telco line features such as Call Waiting. The Flash function is a 600mS timed line break. If the Flash function will be used often, store the feature into memory located for easy access as follows:
1. Press Speakerphone ON/OFF key, then press the “Store” key.
2. Press the “Flash” Key - # 5 & # 13.
3. Press the memory location wherein the “Flash” is to be stored.
4. Press Speaker key to end this programming phase.
Syncing Handsets...
Programming...
Handset Battery...
6ERSION
DECT 6.0 & 1.8GHz Series Features:
• Line Powered - Single & Two Line Telephones
• DECT Non-Interference cordless technology
• SteelTrap memory technology (EEPROM)
• TouchLite one-touch message waiting retrieval
DECT Base:
1. Industrial grade construction, smooth plastic finish
2. Speaker (half duplex)
3. Message Waiting selector switch (submerged) (LR1 LR2 TYPE)
4. Programmable Store key. (submerged) (used to program location in speed dial keys)
5. Programmable Flash key.(submerged) (100mS to 1000mS timed line break, Default is 600mS)
6. Line Cord receptacle (top end of phone) 7a. HSIA (High Speed Internet Access) receptacle incoming from wall (top end of phone) 7b. PassPort® HSIA (High Speed Internet Access) receptacle outgoing to guest laptop
8. Faceplate & Plastic Overlay display area (full-length, 4-color printing possible)
9. Base Ringer Volume switch - LOW or HI settings on Line 1 and Line 2
10. Guest Services Memory keys (10 or 5 keys) (store up to 32 digits maximum)
11. Programmable Pause/Redial key (submerged) (programmable for1.0 to 5.0 second pause) 12a. ADA Compliant Speaker Volume key (up) (8-step control) 12b. ADA Compliant Speaker Volume key (down) (8-step control)
13. Handset Locate key with audio indication
14. Base Microphone
15. Speaker key with No/Off LED indication
16. Mute key with On/Off LED indication
17. TouchLite™ Message Waiting key with 1-touch retrieval bright red color, blinks when message waiting. 18a. Line 1 with LED indication 18b. Line 2 with LED indication
19. Electronic HOLD key with On/Off indication and remote release
20. Dial Pad - (On-hook dialing possible with Memory keys and when Speaker key is activated)
21. Interchangeable handset cradle (provides for special accent colors to light ash or black telephones)
22. Handset Charging location (handset Must be face down to charge)
23. In Use - Ringer indication light
24. Charging Indication light
25. Desi strip display area
13
12b
12a
11
10
8
9
Loading...