Teledyne LeCroy T3PM1006 User manual

T3PM1006

Digital Power Meter

User Manual

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

This manual contains proprietary information, which is protected by
copyright. All rights are reserved. No part of this manual may be
photocopied, reproduced or translated to another language without
prior written consent of Teledyne LeCroy company.

The information in this manual was correct at the time of printing.
However, Teledyne LeCroy continues to improve products and
reserves the rights to change specification, equipment, and
maintenance procedures at any time without notice.

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

TABLE OF CONTENTS

Table of Contents

SAFETY INSTRUCTIONS .................................................. 5

GETTING STARTED ........................................................ 10

Characteristics ............................................................ 11

Appearance ................................................................. 14

Set Up ........................................................................ 23

BASIC SETTING ............................................................. 26

Setting up measurement range ................................... 27

Setting up measurement status .................................. 31

Setting up System status ............................................ 41

MEASUREMENT AND OTHER FUNCTIONS .................... 46

Measurement function ................................................ 47

Other functions .......................................................... 50

Integration measurement function.............................. 52

REMOTE CONTROL ....................................................... 59

Configure Remote Control Interface ............................ 60

Return to Local Control ............................................... 63

COMMAND OVERVIEW ................................................. 64

Command Syntax ........................................................ 64

Command List ............................................................ 68

APPENDIX .................................................................... 102

Specifications ........................................................... 103

Dimensions .............................................................. 108

Power measurement ................................................. 109

Introduction to IEC-62301 ......................................... 111

EUP Directive Lot6 specifications ............................. 112

3

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

Connection Guide ..................................................... 113

CERTIFICATIONS .......................................................... 115

EMC Compliance ...................................................... 115

Safety Compliance .................................................... 117

Environmental Compliance ....................................... 118

RESTRICTION OF HAZARDOUS SUBSTANCES

(RoHS) ..................................................................... 118

4

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

WARNING

Warning: Identifies conditions or practices that
could result in injury or loss of life.

CAUTION

Caution: Identifies conditions or practices that
could result in damage to the T3PM1006
or to other properties.

DANGER High Voltage

Attention Refer to the Manual

Protective Conductor Terminal

Earth (ground) Terminal

1
O

On (Supply)
Off (Supply)

SAFETY INSTRUCTIONS

This chapter contains important safety
instructions that you must follow during
operation and storage. Read the following before
any operation to ensure your safety and to keep
the instrument in the best possible condition.

Safety Symbols

These safety symbols may appear in this manual or on the
instrument.

5

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

General Guideline

CAUTION

 Make sure that the voltage input level does not

exceed DC848V/AC600V.

 Make sure the current input level does not

exceed 20A.

 Do not place any heavy object on the

instrument.

 Avoid severe impact or rough handling that can

lead to damaging the instrument.

 Do not discharge static electricity to the

instrument.

 Use only mating connectors, not bare wires, for

the terminals.

 Do not block or obstruct the cooling fan vent

opening.

 Do not perform measurement at the source of a

low-voltage installation or at building
installations (Note below).

 Do not disassemble the instrument unless you

are qualified as service personnel.

 Make sure that the COM terminal to earth is

limited to 300Vpk.

 Remove all test leads before disconnecting the

mains power cord from the socket.

 If the equipment is used in a manner not

specified by the manufacturer, the protection
provided by the equipment may be impaired.

 The device should be placed in a way that the

plug connected to it can be removed easily.

Safety Guidelines

Find Quality Products Online at: [e-mail]

6

www.GlobalTestSupply.com

SAFETY INSTRUCTIONS

(Note) EN 61010-1:2010 specifies the measurement categories and
their requirements as follows. The T3PM1006 falls under category II
300V.

 Measurement category IV is for measurement performed at the

source of low-voltage installation.

 Measurement category III is for measurement performed in the

building installation.

 Measurement category II is for measurement performed on the

circuits directly connected to the low voltage installation.

Power Supply

WARNING

 AC Input voltage: 100-240 VAC 50/60Hz
 The power supply voltage should not fluctuate

more than 10%.

 Connect the protective grounding conductor of

the AC power cord to an earth ground, to avoid
electrical shock.

Cleaning the
Instrument

 Disconnect the power cord before cleaning.
 Use a soft cloth dampened in a solution of mild

detergent and water. Do not spray any liquid.

 Do not use chemicals containing harsh material

such as benzene, toluene, xylene, and acetone.

Operation
Environment

 Location: Indoor, no direct sunlight, dust free,

almost non-conductive pollution (Note below)

 Temperature: 0°C to 40°C
 Humidity: < 30°C: < 80%RH(non-condensing);

30°C~40°C:<70%RH(non-condensing);
>40°C: <50%RH (non-condensing)

 Altitude: <2000m

(Note) EN 61010-1:2010 specifies the pollution degrees and their
requirements as follows. The T3PM1006 falls under degree 2.

 Pollution refers to “addition of foreign matter, solid, liquid, or

gaseous (ionized gases), that may produce a reduction of
dielectric strength or surface resistivity”.

 Pollution degree 1: No pollution or only dry, non-conductive

pollution occurs. The pollution has no influence.

 Pollution degree 2: Normally only non-conductive pollution

occurs. Occasionally, however, a temporary conductivity caused

7

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

by condensation must be expected.

 Pollution degree 3: Conductive pollution occurs, or dry, non-

conductive pollution occurs which becomes conductive due to
condensation which is expected. In such conditions, equipment
is normally protected against exposure to direct sunlight,
precipitation, and full wind pressure, but neither temperature
nor humidity is controlled.

Storage
environment

 Location: Indoor
 Temperature: -40°C to 70°C
 Humidity: <90%RH(non-condensing)

Disposal

Do not dispose this instrument as unsorted
municipal waste. Please use a separate collection
facility or contact the supplier from which this
instrument was purchased. Please make sure
discarded electrical waste is properly recycled to
reduce environmental impact.

8

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

SAFETY INSTRUCTIONS

Green/ Yellow:

Earth

Blue:

Neutral

Brown:

Live (Phase)

Power cord for the United Kingdom

When using the unit in the United Kingdom, make sure the power
cord meets the following safety instructions.

NOTE: This lead/appliance must only be wired by competent persons

WARNING: THIS APPLIANCE MUST BE EARTHED
IMPORTANT: The wires in this lead are coloured in accordance with the
following code:

As the colours of the wires in main leads may not correspond with
the coloured marking identified in your plug/appliance, proceed
as follows:

The wire which is coloured Green & Yellow must be connected to
the Earth terminal marked with either the letter E, the earth symbol

or coloured Green/Green & Yellow.

The wire which is coloured Blue must be connected to the terminal
which is marked with the letter N or coloured Blue or Black.

The wire which is coloured Brown must be connected to the
terminal marked with the letter L or P or coloured Brown or Red.

If in doubt, consult the instructions provided with the equipment
or contact the supplier.

This cable/appliance should be protected by a suitably rated and
approved HBC mains fuse: refer to the rating information on the
equipment and/or user instructions for details. As a guide, a cable
of 0.75mm2 should be protected by a 3A or 5A fuse. Larger
conductors would normally require 13A types, depending on the
connection method used.

Any exposed wiring from a cable, plug or connection that is
engaged in a live socket is extremely hazardous. If a cable or plug is
deemed hazardous, turn off the mains power and remove the cable,
any fuses and fuse assemblies. All hazardous wiring must be
immediately destroyed and replaced in accordance to the above
standard.

9

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

Characteristics ............................................................ 11

Accessories .............................................................................13

Package Contents ...................................................................13

Appearance ................................................................. 14

Front Panel ..............................................................................14

Display Overview ....................................................................18

Rear Panel ...............................................................................21

Set Up ......................................................................... 23

Tilting the Stand......................................................................23

Power Up .................................................................................24

Connect the wires to the T3PM1006 ......................................25

GETTING STARTED

This chapter describes the T3PM1006, including
accessories, package contents, its main features
and front / rear panel introduction.

Find Quality Products Online at: [e-mail]

10

www.GlobalTestSupply.com

GETTING STARTED

Operation

 Press the buttons on the front panel to easily

turn on the T3PM1006 measurement function.
All settings and measurements results are
displayed on the TFT-LCD screen panel for easy
use of each function.

 Standard display mode: 2 main measurement

results and 6 secondary measurement results are
displayed in this screen.

 Simple display mode: 4 major measurement

results are displayed in this screen.

Performance

 6 selectable voltage ranges available from 15V to

300V with 0.1% of reading + 0.1% of range.

 12 selectable current ranges available from 5mA

to 20A with 0.1% of reading + 0.1% of range.

 It can even measure the voltage of abnormal

wave of CF 3. The half-range CF is up to 6.

Characteristics

The T3PM1006 is a high-precision, programmable power meter for
measuring low power devices such as switching power supplies,
transformers, power supplies, and adapters. It is equipped with a
color TFT-LCD screen which is very convenient for reading the
measurement results. The T3PM1006 has become a reliable power
measurement instruments because of its simple operation, excellent
performance and automatic measurement interface.

11

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

 It can even measure the current of abnormal

wave of CF 3. The half-range CF is up to 6.

 Test terminals in the front panel.
 Total harmonic distortion measurement.

Features

 Full five-digit measurement.
 Voltage measurement range: 15V ~ 600V or

automatic switching

 Current measurement range: 5mA ~ 20A or

automatic switching

 Maximum accuracy of 0.1% of reading + 0.1% of

range

 2 main measurement readings and 6 minor

measurement readings are displayed in the
screen of standard display mode.

 4 main measurement readings are displayed in

the screen of simple display mode.

 Added stand-alone display of total harmonic

distortion measurement function (13 steps)

 Test bandwidth of voltage and current: DC ~

6kHz.

 Added W-h power time integrator function
 Selectable boot settings (Previous / Default)

Interface

 Standard interface: USB / RS232 / LAN

Application

 It can be applied to production test such as

power supplies, transformers, motors, electrical
equipment and other equipment with low
standby power.

 It can be applied to power measurement

conforms to IEC 62301

 It can be applied to assess the power

consumption of product design.

Find Quality Products Online at: [e-mail]

12

www.GlobalTestSupply.com

GETTING STARTED

Standard Accessories

Power Cords x 3

Test leads: 2x red, 2x black

Opening the box

Contents
(single unit)

 Main unit
 Test leads (red x2,

black x2)

 Power cords x 3
 Quick Start Guide

Accessories

Package Contents

Check the contents before using the instrument.

13

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

V -

SetupMode

Enter

StopStart Reset

MAX Hold

Key Lock

ESCLocal

POWER

INTEGRATOR

Range I - Range

CURRENT VOLTAGE

I

AC 10A
MAX

I

V

V

AC 600V

MAX

CAT II 300V

Hold

Current input Voltage input

Power

key

ESC

key

Enter

key

Arrow

keys

Function

keys

LCD display

Power Switch

POWER

Turns On or Off the main
power. For the power up sequence,
see page 24.

Current, Voltage
Terminals

CURRENT VOLTAGE

I

AC 10A

MAX

I

V

V

AC 600V

MAX

CAT II 300V

Current input: I+ and I–
terminals; Voltage
input: V+ and V­terminals.

Appearance

Front Panel

14

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

GETTING STARTED

Note

If the measurement power supply has
positive and negative electrode, please
connect + to the positive electrode of
power supply and - to the negative
electrode of power supply.

Warning

The maximum measurable current and
voltage are 600 V and 10A for voltage
and current terminals of the front
panel of the T3PM1006. Do not input
exceeded voltage and current,
otherwise it will burn the device.

Function keys

V - Range

Enter

V-Range key, up/down arrow keys
and Enter key can be used together
to select a voltage range or auto
range measurement mode. See page

27.

MAX HoldRange I -Range

Enter

I-Range key, up/down arrow keys
and Enter key can be used together
to select a current range or auto
range measurement mode. See page

27.

15

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

MAX Hold

Press this button to display the
maximum measurement reading.
See page 50.

Mode

Press this key to select measure
mode (DC/AC/AC+DC). See page

51.

Setup

Press this key to enter the
measurement settings menu. See
page 31.

Hold

Press this key to switch window and
stop refreshing. See page 51.

Enter

StopStart Reset

INTEGRATOR

Use the left and right arrow
keys to select Integrator
mode, and press Enter
button to enter the time
integrator function. See page

52.

Key Lock

Local

Press this key to toggle to key lock.
In Remote control mode, press this
button to switch to local mode. See
page 51.

Confirm button

Enter

This button is used to enter the
menu, confirm the settings and
switch between the standard display
mode and simple display mode (no
function table and display icon). See
page 51.

16

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

GETTING STARTED

Cancel (Exit)
button

ESC

Press this button to cancel the
current setting. The cursor returns to
the default position or return to the
previous menu according to the
situation. See page 51.

Arrow Keys

These four arrow keys are
used to edit the parameters,
browse the menu system
and select the parameter
range.

17

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

FilterPTCT

Max. Hold

KeyLock

Average Range

Display Hold

Peak Voltage
Peak Current

Remote Error

Remote CF

ModeVoltage Range

Current Range

Secondary Menus

Main

Measurement

Display

Minor

Measurement

Display

Item

Status icon

Description

Voltage Range

V_Range 300V

Voltage measurement range.
Example here range is 300V.

V_Auto means that Auto Range is
turned on.

Current Range

I_Auto 50mA

Current measurement range.
Example here range is 50mA.

I_Auto means that Auto Range is
turned on.

Mode

AC+DC

Measurement mode (AC, DC,
AC+DC)

Remote

RMT

Remote control mode (on/off)

Crest Factor

CF3

Crest Factor (3/6)

Filter

Filter

Voltage and current filters (on/off)

PT Ratio State

PT

External voltage magnification
(on/off)

Display Overview

Find Quality Products Online at: [e-mail]

18

www.GlobalTestSupply.com

GETTING STARTED

CT Ratio State

CT

External current magnification
(on/off)

Maximum Hold

Max. Hold

Retain and display the maximum
measurement reading.

Keyboard Lock

KeyLock

Lock Key button

Average

Avg-1

Average number of sampling
(1/2/4/8/16/32/64)

Display Hold

Hold

Retain and display the current
measurement reading.

Peak Voltage

P.V

The voltage exceeds the
measurement range

Peak Current

P.I

The current exceeds the
measurement range

Remote Error

Err-XXX

An error occurs in remote
command

Standard Display
Mode

Display the measurement result of 2 major and 6
minor measurement parameters

Simple Display
Mode

Display the measurement result of 4 major
measurement parameters

Secondary menus

Display secondary function menu

 Enlarge

This function key is used to switch
display of measurement result from 2
major plus 6 minor to 4 major ones.

 Integrator

This function key is used to set up
integrator measurement parameters
and execute integrator measurement
function.

 Parameter

This function key is used to set up
measurement parameters.

19

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

 System

This function key is used to enter the
system setting and system
configuration screens.

20

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

GETTING STARTED

I I

20A

MAX

100 240V

25VA MAX

AC
50 / 60Hz

V V

CAT II 300V

RS232

LAN

GPIB

SER.NO. LABEL

REMOVE INPUTS BEFORE OPENING.

TO AVOID SHOCK,

WARNING

600V

MAX

CURRENT VOLTAGE

AC power input

USB B

port

RS232

port

LAN
port

Voltage

input

Current

input

Power Cord
Socket

100 240V

25VA MAX

AC
50 / 60Hz

Accepts the power cord.
AC 100~240V ±10%,
50/60Hz

RS232

RS232

RS232 port. This port is used for
remote control.

USB Device Port

Type B USB port. This port is used
for remote control.

LAN Port

LAN

LAN Port.

Rear Panel

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

21

T3PM1006 User Manual

Rear
Voltage/Current
input terminal

I I

20A

MAX

V V

CAT II 300V

600V

MAX

CURRENT VOLTAGE

Rear
Voltage/Current
input terminal is
used to connect
the main
measurement
signals.

Warning

 Do not use damaged device. Before using the

equipment, check its housing first to ensure there
are no cracks. Do not operate this device in an
environment containing explosive gases, steam or
dust.

 The maximum measurable current and voltage are

600 V and 20A for voltage and current terminals of
the rear panel of the T3PM1006. Do not input
exceeded voltage and current, otherwise it will burn
the device.

 Always use the supplied cable for connection.
 Before connecting the device, observe all the safety

symbols marked on the device.

 Turn off the power to the device and the application

system before connecting I/O terminals.

 Do not install replacement parts on the device or

perform any unauthorized modifications.

 Do not use this device if the removable cover is

removed or loosened.

 Do not connect any cables and terminals before

performing self-test.

 Use only the power adapter supplied by the

manufacturer to avoid accidental injury.

 Do not use this device for life support systems or

any other equipment that has safety requirements.

22

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

GETTING STARTED

From the base of the handle, gently pull the handle out sideways
and then rotate it to one of the following positions.

Horizontal
position

Tilt stand
position

Carry position

Set Up

Tilting the Stand

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

23

T3PM1006 User Manual

Steps

1. Ensure the AC voltage is 100~ 240V.

2. Connect the power

cord to the AC
voltage input.

Note

Make sure the ground connector on the power
cord is connected to a safety ground. This will
influence the measurement accuracy.

3. Push to turn on the main

power switch on the front
panel.

4. The display turns on and shows the last

function that was used before the power was
reset.

Power Up

24

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

GETTING STARTED

Background

Two separate wires are used to connect the
T3PM1006, so voltage and current
measurement are isolated and don’t interfere
with each other.

Connection
diagram

CURRENT VOLTAGE

I

AC 10A
MAX

I

V

V

AC 600V

MAX

CAT II 300V

I I

20A

MAX

V V

CAT II 300V

600V

MAX

CURRENT VOLTAGE

Note

The terminals on the front and rear panels can’t be
used as input terminal at the same time.

Description

V +

The positive voltage input (+)

V -

The negative voltage input (-)

I +

The positive current input (+), 10A for
input on the front panel, 20A for input on
the rear panel.

I -

The negative current input (-), 10A for
input on the front panel, 20A for input on
the rear panel.

GND

Provide reference grounding.

Connect the wires to the T3PM1006

25

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

Setting up measurement range ................................... 27

Auto Range ..............................................................................29

Setting up measurement status .................................. 31

Setting up synchronization source .........................................31

Setting up filter .......................................................................32

Setting up crest factor ............................................................33

Setting up auto-zero function .................................................34

Setting up average value .........................................................35

Setting up method of calculating harmonics .........................36

Setting up the PT ratio status .................................................37

Setting up the CT ratio status.................................................38

Setting up the voltage and current skipping configuration ...39

Setting up System status ............................................ 41

System configuration setting screen ......................................41

Setting up power on status ....................................................41

Setting up brightness .............................................................42

Setting up key sound ..............................................................43

Setting up interface .................................................................44

BASIC SETTING

Find Quality Products Online at: [e-mail]

26

www.GlobalTestSupply.com

BASIC SETTING

Set voltage range

1. Press V-Range button.

V - Range

2. Use up and down arrow keys to

select the desired range.

3. Press Enter button to confirm your

selection.

Enter

Available range

Crest Factor
is 3:

AUTO, 15V, 30V, 60V, 150V, 300V, 600V

Crest Factor
is 6:

AUTO, 7.5V, 15V, 30V, 75V, 150V, 300V

Set current range

1. Press I-Range button.

MAX HoldRange I -Range

Setting up measurement range

To get accurate measurement results, set an appropriate
measurement range before performing measurements.

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

27

T3PM1006 User Manual

2. Use up and down arrow keys to

select the desired range.

3. Press Enter button to confirm your

selection.

Enter

Available range

Crest Factor
is 3:

AUTO, 5mA, 10mA, 20mA, 50mA,
100mA, 200mA, 0.5A, 1A, 2A, 5A,10A,
20A

Crest Factor
is 6:

AUTO, 2.5mA, 5mA, 10mA, 25mA,
50mA, 100mA, 250mA, 0.5A, 1A, 2.5A,
5A, 10A

Note

When the measurement range is set manually, if the
range status icon lights in green, the measured value
meets the setting range. On the contrary, if the range
status icon lights in red, the measured value doesn’t
meet the best setting range. In this case, it is better to
switch to another range to get more accurate
measurement results.

Note

The P.I status icon lights in red when the current
measurement circuit detects that the measured value
exceeds setting range by 3 folds (CF is set to 3) or 6
folds (CF is set to 6).

Find Quality Products Online at: [e-mail]

28

www.GlobalTestSupply.com

BASIC SETTING

Note

The P. V status icon lights in red when the voltage
measurement circuit detects that the measured value
exceeds setting range by 3 folds (CF is set to 3) or 6
folds (CF is set to 6).

Range is shift up

The range is shifted up when either of the
following conditions is met.

 Vrms or Irms exceeds the current setting range

by 110%.

 The Vpk or Ipk value of the input signal exceeds

the current setting range by 330% at CF 3.

 The Vpk or Ipk value of the input signal exceeds

the current setting range by 660% at CF 6.

Range is shift
down

The range is shifted down when all of the
following conditions are met.

 Vrms or Irms is equal to or less than the 60% of

previous range.

 The Vpk or Ipk value of the input signal is less

than the next setting range by 300% at CF 3.

 The Vpk or Ipk value of the input signal is less

than the next setting range by 600% at CF 6.

Auto Range

The range is automatically switched according to the voltage and
current of input signal.

29

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

Example

Irms exceeds the current setting range by 110%,
so range is shifted to 20mA

Irms is less than or equal to 60% of the previous
setting range, so range is shifted down to
10mA.

Find Quality Products Online at: [e-mail]

30

www.GlobalTestSupply.com

BASIC SETTING

Steps

1. Press Setup button.

Setup

2. Press Enter button.

Enter

3. Press down arrow key.

4. Press Enter button to enter Sync

Source item. Use up and down
arrow keys to select the desired
option and then press Enter button
again to confirm your selection.

Enter

Enter

Option

V:

Select the voltage of signals as
synchronization source.

I:

Select the current of signals as
synchronization source.

OFF:

Select the entire interval of data updating
period as synchronization source.

Default value

V

Setting up measurement status

Setting up synchronization source

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

31

T3PM1006 User Manual

Steps

1. Press Setup button.

Setup

2. Press Enter button.

Enter

3. Press down arrow key twice.

x2

4. Press Enter button to enter Filter

item. Use up and down arrow keys
to select the desired option and
then press Enter button again to
confirm your selection.

Enter

Enter

Option

On:

Turn on the line filter function and Filter
status icon on the display lights up in green.

Off:

Turn off the line filter function. Line filter
cutoff frequency is 500Hz

Default value

Off

Setting up filter

32

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

BASIC SETTING

Steps

1. Press Setup button.

Setup

2. Press Enter button.

Enter

3. Press down arrow key three times.

x3

4. Press Enter button to enter Crest

Factor item. Use up and down

arrow keys to select the desired
option and then press Enter button
again to confirm your selection.

Enter

Enter

Option

3:

Crest Factor is three.

6:

Crest Factor is six.

Default value

3

Setting up crest factor

33

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

Steps

1. Press Setup button.

Setup

2. Press Enter button.

Enter

3. Press down arrow key four times.

x4

4. Press Enter button to enter Auto

Zero item. Use up and down arrow

keys to select the desired option
and then press Enter button again
to confirm your selection.

Enter

Enter

Option

On:

Auto-zero function is activated once per
hour or when range is switched

Off:

Auto-zero function is only activated once
when the range is switched. The auto-zero
function is turned off when the integrator
function is executed

Default value

Off

Setting up auto-zero function

34

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

BASIC SETTING

Steps

1. Press Setup button.

Setup

2. Press Enter button.

Enter

3. Press down arrow key five times.

x5

4. Press Enter button to enter Average

item. Use up and down arrow keys
to select the desired option and
then press Enter button again to
confirm your selection.

Enter

Enter

Option

1, 2, 4, 6, 8, 16, 32 and 64:
The measurement time is synchronized with the
average value that you set. The larger the average
value is, the longer the measurement time is.
When the average value is set to 1, the
measurement time is about 0.1 seconds. The
larger the number is, the longer the measurement
time is, and so forth.

Default value

2

Setting up average value

35

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

Steps

1. Press Setup button.

Setup

2. Press Enter button.

Enter

3. Press down arrow key six times.

x6

4. Press Enter button to enter

Harmonics item. Use up and down

arrow keys to select the desired
option and then press Enter button
again to confirm your selection.

Enter

Enter

Option

IEC:

Calculate the ratio of harmonic quantity of
the 2nd through the 13th harmonic to the
1st harmonic.

CSA:

Calculate the ratio of harmonic quantity of
the 2nd through the 13th harmonic to the
1st through the 13th harmonic.

Off:

Turn off the harmonic calculation function.

Default value

Off

Setting up method of calculating harmonics

36

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

BASIC SETTING

Steps

1. Press Setup button.

Setup

2. Press Enter button.

Enter

3. Press down arrow key seven times.

x7

4. Press Enter button to enter PT

Ratio Status item. Use up and

down arrow keys to select the
desired option and then press Enter
button again to confirm your
selection.

Enter

Enter

Option

On:

Turn on the PT ratio calculation function and
PT status icon on the display lights up in
green. The setting range is from "1" to
"9999.999".

Off:

Turn off the PT ratio calculation function.

Default option

Off

Setting up the PT ratio status

37

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

Steps

1. Press Setup button.

Setup

2. Press Enter button.

Enter

3. Press down arrow key eight times.

x8

4. Press Enter button to enter CT

Ratio Status item. Use up and

down arrow keys to select the
desired option and then press Enter
button again to confirm your
selection.

Enter

Enter

Option

On:

Turn on the CT ratio calculation function and
CT status icon on the display lights up in
green. The setting range is from "1" to
"9999.999".

Off:

Turn off the CT ratio calculation function.

Default option

Off

Setting up the CT ratio status

38

www.GlobalTestSupply.com

Find Quality Products Online at: [e-mail]

Steps

1. Press Setup button.

Setup

2. Press right arrow key to enter

SETUP1 tab.

3. Press Enter button.

Enter

4. Press down arrow key to enter the

V/I-Range Skipping Config.

5. Press Enter button.

Enter

6. Press up and down arrow keys to

turn On the V/I-Range Skipping
Config.

BASIC SETTING

Setting up the voltage and current skipping configuration

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

39

T3PM1006 User Manual

7. Press Enter button to confirm

setting.

Enter

8. Press up, down, right and left

arrow keys to move cursor to V-
Range and I-Range fields where
options are available for user to
enable or disable for measurement.

9. When, for example, disabling 15V

option, move cursor to 15V
followed by pressing Enter button
and using up and down arrow keys
to select Off. Press Enter key to
confirm setting in the end.

Enter

Enter

Option

On

When the option(s) is On, the selected
range(s) will be applied to measurement.

Off

It is able is skip certain measurement
range(s) that are not used by turning Off.
By doing so, It can reduce measured data loss
which happens while ranges are switched.

Default value

On

40

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

BASIC SETTING

Steps

1. Use left and right arrow keys on

the front panel to select System
function key.

2. Press Enter button to Enter

SYSTEM INFORMATION setting
screen.

Enter

3. Press right arrow key to select

Config key.

4. Press Enter button to enter

SYSTEM CONFIG setting screen.

Enter

Background

Continue the following setting from SYSTEM
CONFIG setting screen

Steps

1. Press down arrow key.

Setting up System status

System configuration setting screen

Setting up power on status

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

41

T3PM1006 User Manual

2. Press Enter button to enter Power

On Status Setup item. Use up and

down keys to select the desired
option and then press Enter button
again to confirm your selection.

Enter

Enter

Option

Previous:

The status of device on powering on is
set to the status before the last
shutdown.

Default:

The status of device on powering on is
set to the factory default status.

Default value

Default

Background

Continue the following setting from SYSTEM
CONFIG setting screen

Steps

1. Press down arrow key twice.

x2

Setting up brightness

42

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

BASIC SETTING

2. Press Enter button to enter

Brightness item. Use up and down

keys to select a number and then
press Enter button again to confirm
your selection.

Enter

Enter

Option

1 to 9

The display is the darkest when set to

1. On the contrary, the brightest when
set to 9.

Default option

7

Background

Continue the following setting from SYSTEM
CONFIG setting screen

Steps

1. Press down arrow key three times.

x3

Setting up key sound

43

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

2. Press Enter button to enter Key

Sound item. Use up and down

arrow keys to select the desired
option and then press Enter button
again to confirm your selection.

Enter

Enter

Option

On:

A short sound is heard from the
speaker of device when pressing the
keys on the front panel.

Off:

No sound from the speaker of device
when pressing the keys on the front
panel.

Default option

Off

Background

Continue the following setting from SYSTEM
CONFIG setting screen

Steps

1. Press down arrow key four times.

x4

Setting up interface

44

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

BASIC SETTING

2. Press Enter button to enter I/O

Model item. Use up and down

arrow keys to select the desired
option and then press Enter button
again to confirm your selection.

Enter

Enter

Option

RS232:

If interface is set to RS232, the Baud
Rate can be selected from the following
options.

1200, 2400, 4800, 9600, 19200, 38400,
57600 or 115200

For details about configuring RS 232
interface, please see page 60.

USB:

For details about configuring USB
interface, please see page 60.

GPIB:

Disabled

LAN:

If interface is set to LAN, the IP model
can be selected “Manual” or “DHCP”.

Note that the socket port is fixed in “23”

for the unit. For details about configuring
LAN interface, please see page 61.

Default value

RS232, 9600

45

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

Measurement function ................................................ 47

Introduction to measurement parameters ............................47

Setting measurement parameters ..........................................48

Other functions .......................................................... 50

Introduction to other functions ..............................................50

Integration measurement function .............................. 52

Setting up Integrator measurement .......................................52

Introduction to integrator parameters ...................................55

Using the integrator function .................................................57

MEASUREMENT AND

OTHER FUNCTIONS

46

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

MEASUREMENT AND OTHER FUNCTIONS

Parameter name

Display icon

Voltage

Vdc (DC voltage), Vrms (AC voltage)

Current

Idc (DC current), Irms (AC current)

Active Power

P

Apparent Power

VA

Reactive power

VAR

Power Factor

PF

Phase Angle

DEG

Frequency

IHz and VHz

Voltage Peak

V+pk and V-pk

Current Peak

I+pk and I-pk

Measurement function

The T3PM1006 provides a wide range of basic electricity and power
measurement functions. It is equipped with different accurate
measurement parameters for accurately measuring the voltage,
current, power, DC/AC/AC + DC, power factor, harmonics,
frequency, etc. The input impedance of the device is 2.4MΩ, the
maximum input voltage is 600Vrms. There are 2 sets of internal
resistance (Shunt), 500mΩ and 5mΩ respectively. The maximum
input current is 20Arms. The device will issue a warning sound
when the input voltage and current exceed 700 Vrms or 25Arms.

Introduction to measurement parameters

47

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

Active Power
Peak

P+pk and P-pk

Total Harmonic
Distortion

THDI and THDV

Crest factor

CFV, CFI

Steps

1. Use left and right arrow keys on

the front panel to select Parameter
function key.

2. Press Enter button. A measurement

parameter will be highlighted in
green.

Enter

3. Press Enter button to confirm

setting or use up and down arrow
keys to select other desired
measurement parameter.

4. You can use same method as

shown in the last step to set other
measurement parameters in this
screen.

Enter

Enter

Setting measurement parameters

Please follow the steps blow to set the measurement parameters

48

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

MEASUREMENT AND OTHER FUNCTIONS

Switching display
mode

5. In standard display mode, you

simply press the Enter button to
switch display mode to simple.

Enter

6. Press ESC button to return back to

original display mode.

ESC

49

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

Max. Hold KeyLock Display HoldMode

Function name

Button

Description

MAX Hold

MAX Hold

When the MAX Hold button is
pressed, the MAX Hold status icon
will light in red in the LCD display to
indicate that this function is activated.
To deactivate this function, press this
button again.

If the MAX Hold function is activated,
the display value on the display is
updated only when the current
measured value is greater than the
previous measured value. The
maximum display value is retained
on the display.

Other functions

Introduction to other functions

50

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

MEASUREMENT AND OTHER FUNCTIONS

Mode

Mode

Press this button to select
measurement mode. There are 3
measurement modes.

 AC+DC: Displays all the

components of the measurement
signal

 DC: Displays the DC part of the

measurement signal.

 AC: Displays the AC part of the

measurement signal.

Hold

Hold

When the Hold button is pressed, the
Hold status icon will light in red in
the LCD display to indicate that this
function is activated. To deactivate
this function, press this button again.

When the Hold function is activated,
the displayed value on the LCD
display is not updated and the range
is locked. Measurement is performed
in the background.

Local/ KeyLock

Key Lock

Local

Dual function key. When Remote
mode is activated, press this button to
deactivate Remote mode and switch
to Local mode. When Remote mode is
not activated, this button is used as
lock key of keypad.

Enter

Enter

This button is used to select function
or confirm selection.

ESC

ESC

This button is used to exit current
screen or return to main measurement
screen.

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

51

T3PM1006 User Manual

Steps

1. Use left and right arrow keys on

the front panel to select Integrator
function key.

2. Press Enter button to enter the

integrator measurement screen.

Enter

3. Press right arrow key to select Set

key.

Integration measurement function

Setting up Integrator measurement

Find Quality Products Online at: [e-mail]

52

www.GlobalTestSupply.com

MEASUREMENT AND OTHER FUNCTIONS

Select integrator
measurement
mode

4. Press Enter button to enter

integrator measurement setting
screen.

Enter

5. Press Enter button to enter Mode

item. Use up and down arrow keys
to toggle between Manual and
Standard mode. Press Enter button
again to confirm your selection.

If you select Manual mode, the Set
time is disabled and displayed in
gray.

Enter

Enter

Find Quality Products Online at: [e-mail]

53

www.GlobalTestSupply.com

T3PM1006 User Manual

If you select standard mode, you
need to set integrator measurement
time before using integrator
function. It can be set from 1
second to 9999 hours, 59 minutes
and 59 seconds.

6. Press down arrow key to select

Function item in the integrator
measurement setting screen.

Select integrator
measurement
function

7. Press Enter button to enter

Function item. Use up and down

arrow keys to toggle between
Ampere Hours and Watt Hours.
Press Enter button again to confirm
your selection.

Enter

Enter

Find Quality Products Online at: [e-mail]

54

www.GlobalTestSupply.com

MEASUREMENT AND OTHER FUNCTIONS

Parameter name

Description

Mode

 Manual
 Standard

Function

 Watt Hours

WP: Total power
WP+: Positive total
power
WP-: Negative total
power

 Ampere Hours

q: Total mAh
q+: Positive total
mAh
q-: Negative total
mAh

Set time

It indicates the time of integrator measurement to
be set. It can be set from 1 second to 9999 hours, 59
minutes and 59 seconds.

Test time

It indicates that elapsed time of integrator
measurement.

Introduction to integrator parameters

55

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

State

 Running

Integrator
measurement is in
progress.

 Stop

Integrator
measurement has
been stopped
manually.

 Timeout

The time for
running integrator
measurement is up.

 Reset

The integrator
measurement
status is cleared.

56

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Manual mode

1. In manual mode, you can directly

press the Start button in the front
panel to start integrator function.

Start

INTEGRATOR

2. To stop integration function, press

the Stop button in the front panel.

Stop

3. Press the Reset button in the front

panel to clear integrator.

Reset

MEASUREMENT AND OTHER FUNCTIONS

Using the integrator function

57

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

Standard mode

1. Set integrator measurement time before using

integrator function.

2. Other steps are the same as running in manual

mode.

When integrator is running, the test time will
increase until the setting integrator
measurement time.

Note

 In the integration process, select the Measure

key and press Enter button to return main
measurement screen. Select Integrator key and
press Enter button to switch back to integration
measurement screen.

 In the integration process, you can’t change

measurement range and enter system to set
measurement parameters.

 In the integration process, if the voltage or

current measurement value is exceeded, the
measured value will display in red.

Find Quality Products Online at: [e-mail]

58

www.GlobalTestSupply.com

REMOTE CONTROL

Configure Remote Control Interface ............................ 60

USB Interface ......................................................................... 60

Configure USB Interface ........................................................ 60

Configure RS232 Interface ..................................................... 60

Configure LAN Interface ........................................................ 61

Return to Local Control ............................................... 63

REMOTE CONTROL

This chapter describes basic configuration of
IEEE488.2 based remote control. For a command
list, refer to the Command Overview chapter on
page 64.

59

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

USB
Configuration

PC connector

Type A, host

T3PM1006 connector

Rear panel Type B, slave

Speed

1.1/2.0 (full speed/high
speed)

USB Class

CDC (Communications
device class)

Hardware flow control

Off

Data Bits

8

Stop bit

1

RS232
Configuration

Selectable Baud rate

1200, 2400,4800, 9600,
19200, 38400, 57600,
115200

Parity

None

Hardware flow control

Off

Data Bits

8

Stop bit

1

Configure Remote Control Interface

USB Interface

The USB device port on the rear panel is used for remote control.
The USB port is configured as CDC interface.

When configured to CDC, the USB port on the T3PM1006 will
appear as a virtual COM port to a connected PC. Any terminal
program that can communicate via a serial port can be used for
remote control. Before the T3PM1006 can be used for remote
control using the CDC USB class, install the appropriate CDC USB
driver available for download on the Teledyne LeCroy website.

Configure USB Interface

Configure RS232 Interface

60

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

REMOTE CONTROL

RS232 Pin
Assignments

Pin 2: RxD
Pin 3: TxD
Pin 5: GND
Pin 1, 4, 6 ~ 9: No
Connection

1

2345

6789

PC Connection

Use a Null Modem connection as shown in the
diagram below.

T3PM1006 PC

RxDPin2 RxD Pin2

GNDPin5 GND Pin5

TxD Pin3

TxDPin3

Background

Continue the following setting from SYSTEM
CONFIG setting screen

Steps

1. Press down arrow key four times.

x4

2. Press Enter button to enter I/O

Model item. Use up and down

arrow keys to select LAN option
and then press Enter button again
to confirm your selection.

Enter

Enter

Configure LAN Interface

61

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

3. Select a desired IP Model.

Option

Manual

Set up IP Address, Subnet mask and
Gateway manually.

DHCP

DHCP server automatically assigns IP
Address, Subnet mask and Gateway.

62

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

REMOTE CONTROL

Background

When the unit is in remote control mode, the
RMT icon above the main display can be seen.
When this icon is not displayed, it indicates that
the unit is in local control mode.

Procedure

1. Press the LOCAL key when in remote mode.

2. The unit will go back into local mode and the

RMT icon will turn off.

Return to Local Control

63

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

Compatible
Standard

IEEE488.2

Partial compatibility

SCPI, 1994

Partial compatibility

Command
Structure

SCPI (Standard Commands for Programmable
Instruments) commands follow a tree-like
structure, organized into nodes. Each level of
the command tree is a node. Each keyword in a
SCPI command represents each node in the
command tree. Each keyword (node) of a SCPI
command is separated by a colon (:).
For example, the diagram below shows an SCPI
sub-structure and a command example.

DCAC

DC AC

INPut:MODE DC

:MODE

:INPut

COMMAND OVERVIEW

The Command overview chapter lists all
programming commands in functional order as
well as alphabetical order. The command syntax
section shows you the basic syntax rules you have
to apply when using commands.

Command Syntax

64

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

COMMAND OVERVIEW

Command Types

There are a number of different instrument
commands and queries. A command sends
instructions or data to the unit and a query
receives data or status information from the
unit.

Command types

Simple

A single command
with/without a parameter

Example

:INPut:MODE DC

Query

A query is a simple or
compound command
followed by a question mark
(?). A parameter (data) is
returned.

Example

:INPut:CFACtor?

Command Forms

Commands and queries have two different
forms, long and short. The command syntax is
written with the short form of the command in
capitals and the remainder (long form) in lower
case.
The commands can be written either in capitals
or lower-case, just so long as the short or long
forms are complete. An incomplete command
will not be recognized.
Below are examples of correctly written
commands.

Long form

:INPut:SYNChronize VOLTage

:COMMunicate:HEADer ON

Short form

:INP:SYNC VOLT
:COMM:HEAD ON

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

65

T3PM1006 User Manual

Square Brackets

Commands that contain square brackets
indicate that the contents are optional. The
function of the command is the same with or
without the square bracketed items, as shown
below. For example, for the query:

[:INPut]:FILTer?
Both :INPut:FILTer? and :FILTer? are valid forms.

Command
Format

300

1

2 3

:INPut:VOLTage:RANGe

1. Command header

2. Space

3. Parameter 1

Common
Input Parameters

Type

Description

Example

<Boolean>

boolean logic

0, 1

<NR1>

integers

0, 1, 2, 3

<NR2>

decimal numbers

0.1, 3.14, 8.5

<NR3>

floating point with
exponent

4.5e-1, 8.25e+1

<NRf>

any of NR1, 2, 3

1, 1.5, 4.5e-1

[MIN]
(Optional
parameter)

For commands, this will set the
setting to the lowest value. This
parameter can be used in place of any
numerical parameter where indicated.

For queries, it will return the lowest
possible value allowed for the
particular setting.

66

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

COMMAND OVERVIEW

[MAX]
(Optional
parameter)

For commands, this will set the
setting to the highest value. This
parameter can be used in place of any
numerical parameter where indicated.

For queries, it will return the highest
possible value allowed for the
particular setting.

Message
Terminator (EOL)

Remote
Command

Marks the end of a command line. The
following messages are in accordance
with IEEE488.2 standard.

CR+LF

The most
common EOL
character is
CR+LF

Message
Separator

EOL or ;
(semicolon)

Command Separator

67

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

SCPI Commands

*CLS ............................................................................. 70

*IDN ............................................................................ 70

*ESE ............................................................................. 70

*ESR ............................................................................. 71

*OPC ............................................................................ 71

*RST ............................................................................. 71

*SRE ............................................................................. 72

*STB ............................................................................. 72

COMMunciate
Commands

:COMMunicate:HEADer ............................................. 73

:COMMunicate:REMote .............................................. 73

:COMMunicate:VERBose ............................................ 74

DISPlay
Commands

:DISPlay[:NORMal]:ITEM<x> ...................................... 75

:DISPlay:INTegrate:ITEM<x> ...................................... 76

:DISPlay:PAGE ............................................................. 77

HARMonics
Command

:HARMonics:THD ....................................................... 78

HOLD Command

:HOLD .......................................................................... 79

INPut
Commands

[:INPut]:CFACtor .......................................................... 80

[:INPut]:MODE ............................................................ 80

[:INPut]:VOLTage:RANGe ........................................... 81

[:INPut]:VOLTage:AUTO ............................................. 81

[:INPut]:VOLTage:CONFig .......................................... 82

[:INPut]:CURRent:RANGe ........................................... 82

[:INPut]:CURRent:AUTO ............................................. 83

[:INPut]:CURRent:CONFig .......................................... 83

[:INPut]:RCONfig ......................................................... 84

[:INPut]:SCALing:{VT/PT|CT}:STATe .......................... 84

[:INPut]:SCALing:{VT/PT|CT}:RATio ........................... 85

[:INPut]:SYNChronize .................................................. 85

[:INPut]:FILTer ............................................................. 85

Command List

Find Quality Products Online at: [e-mail]

68

www.GlobalTestSupply.com

COMMAND OVERVIEW

[:INPut]:ZERO ..............................................................86

INTegrate
commands

:INTegrate:MODE ........................................................87

:INTegrate:FUNCtion ..................................................87

:INTegrate:TIMer .........................................................88

:INTegrate:STARt .........................................................88

:INTegrate:STOP ..........................................................88

:INTegrate:RESet .........................................................88

:INTegrate:STATe ........................................................89

MEASure
commands

:MEASure:AVERaging:COUNt ....................................90

:MEASure:MHOLd ......................................................90

NUMeric
commands

:NUMeric[:NORMal]:VALue ........................................91

:NUMeric[:NORMal]:NUMBer ....................................92

:NUMeric[:NORMal]:ITEM<x> ....................................92

:NUMeric[:NORMal]:PRESet .......................................94

:NUMeric[:NORMal]:CLEar .........................................96

:NUMeric[:NORMal]:DELete .......................................97

:NUMeric[:NORMal]:HEADer .....................................97

SYSTem
commands

:SYSTem:MODel ..........................................................98

:SYSTem:SERial ...........................................................98

:SYSTem:VERSion ........................................................98

:SYSTem:KLOCk ..........................................................99

:SYSTem:BRIGhtness ..................................................99

:SYSTem:KEY:BEEPer ................................................100

STATus command

:STATus:ERRor ...........................................................101

69

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

*CLS ............................................................................. 70

*IDN ............................................................................ 70

*ESE ............................................................................. 70

*ESR ............................................................................. 71

*OPC ............................................................................ 71

*RST ............................................................................. 71

*SRE ............................................................................. 72

*STB ............................................................................. 72

*CLS

Description

Clears the Event Status register (Output Queue,
Operation Event Status, Standard Event Status).

Syntax

*CLS

*IDN

Description

Returns the manufacturer, model number, serial
number, and system version of the instrument.

Query Syntax

*IDN?

Return parameter

<String>

Example

*IDN?

->TELEDYNE,T3PM1006, GXXXXXXXX,V1.00

*ESE

Description

Sets or returns the ESER (Event Status Enable
Register) contents.

Syntax

Query Syntax

*ESE <NR1>

*ESE?

Set

Query

Set

Query

SCPI Commands

70

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

COMMAND OVERVIEW

Parameter/

Return parameter

<NR1>

0~255

Example

*ESE 65
Set the ESER to 01000001

*ESE?

->130
ESER=10000010

*ESR

Description

Returns SESR (Standard Event Status Register).

Query Syntax

*ESR?

Return parameter

<NR1>

0~255

Example

*ESR?

->198
SESR=11000110

*OPC

Description

Sets or returns the operation complete bit (bit0) in
SERS (Standard Event Status Register) when all
pending operations are completed.

Syntax

Query Syntax

*OPC

*OPC?

Return parameter

<NR1>0

Operation isn’t completed

<NR1>1

Operation is completed

Example

*OPC?

Returns 1.

*RST

Description

Initializes the settings

Syntax

*RST

Query

Set

Query

Set

71

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

*SRE

Description

Sets or returns SRER (Service Request Enable
Register)

Syntax

*SRE <NR1>

Query Syntax

*SRE?

Parameter/
Return parameter

<NR1>

0~255

Example

*SER 7
Set the the SRER to 00000111
*SRE?

->3

SRER=00000011

*STB

Description

Returns the SBR (Status Byte Register) contents.

Query Syntax

*STB?

Return parameter

<NR1>

0~255

Example

*STB 8

->81
SESR=01010001

Set

Query

Query

72

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

COMMAND OVERVIEW

:COMMunicate:HEADer ..............................................73

:COMMunicate:REMote ..............................................73

:COMMunicate:VERBose ............................................74

:COMMunicate:HEADer

Description

Sets or returns whether headers are attached to
query responses

Syntax

:COMMunicate:HEADer <Boolean>|{OFF | ON}

Query Syntax

:COMMunicate:HEADer?

Parameter

<Boolean>0

OFF

<Boolean>1

ON

Return parameter

0

Turn the header function off

1

Turn the header function on

Example

:COMMUNICATE:HEADER ON

:COMMUNICATE:HEADER?

->:COMMUNICATE:HEADER 1

Note

Example of a response with a header

:INPUT:VOLTAGE:RANGE 150.0E+00

Example of a response without a header 150.0E+00

:COMMunicate:REMote

Description

Sets or returns the T3PM1006 to remote or local
mode. ON is remote mode.

Syntax

:COMMunicate:REMote <Boolean>|{OFF | ON}

Query Syntax

:COMMunicate:REMote?

Set

Query

Set

Query

COMMunciate Commands

73

www.GlobalTestSupply.com

Find Quality Products Online at: [e-mail]

T3PM1006 User Manual

Parameter

<Boolean>0

OFF

<Boolean>1

ON

Return parameter

0

Turn the remote function off

1

Turn the remote function on

Example

:COMMUNICATE:REMOTE ON

:COMMUNICATE:REMOTE?

->:COMMUNICATE:REMOTE 1

:COMMunicate:VERBose

Description

Sets or returns whether the response to a query is
returned fully spelled out or in its abbreviated
form.

Syntax

:COMMunicate:VERBose <Boolean>|{OFF | ON}

Query Syntax

:COMMunicate:VERBose?

Parameter

<Boolean>0

OFF

<Boolean>1

ON

Return parameter

0

Turn the verbose function off

1

Turn the verbose function on

Example

:COMMUNICATE:VERBOSE ON

:COMMUNICATE:VERBOSE?

->:COMMUNICATE:VERBOSE 1

Note

Example of a response fully spelled out

:INPUT:VOLTAGE:RANGE 150.0E+00

Example of a response in abbreviated form

:VOLT:RANG 150.0E+00

Set

Query

74

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

COMMAND OVERVIEW

:DISPlay[:NORMal]:ITEM<x> ......................................75

:DISPlay:INTegrate:ITEM<x> ......................................76

:DISPlay:PAGE .............................................................77

:DISPlay[:NORMal]:ITEM<x>

Description

Sets or returns a normal measurement data display
item.

Syntax

:DISPlay[:NORMal]:ITEM<x> <Function>

Query Syntax

:DISPlay[:NORMal]:ITEM<x>?

Parameter/

Return parameter

<x>

1 to 8 (display)

<Function>

{U|UPPeak|UMPeak|I|IPPeak|IMPeak
|P|PPPeak|PMPeak|S|Q|LAMBda|CFU
|CFI|PHI|FU|FI|UTHD|ITHD}

Example

:DISPLAY:NORMAL:ITEM1 U

:DISPLAY:NORMAL:ITEM1?

->:DISPLAY:NORMAL:ITEM1 U

<Function>

Function

T3PM1006 Indicator

U

Voltage U

[V]

UPPeak

Maximum voltage: U+pk

[V+pk]

UMPeak

Minimum voltage: U-pk

[V-pk]

I

Current I

[I]

IPPeak

Maximum current: I+pk

[I+pk]

IMPeak

Minimum current: I-pk

[I-pk]

P

Active power P

[P]

PPPeak

Maximum power: P+pk

[P+pk]

PMPeak

Minimum power: P-pk

[P-pk]

S

Apparent power S

[VA]

Set

Query

DISPlay Commands

75

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

Q

Reactive power Q

[VAR]

LAMBda

Power factor λ

[PF]

CFU

Voltage factor λ

[CFV]

CFV

Current factor λ

[CFI]

PHI

Phase difference Φ

[DEG]

FU

Voltage frequency fu

[VHz]

FI

Current frequency fI

[AHz]

UTHD

Total harmonic distortion of
voltage Uthd

[THDV]

ITHD

Total harmonic distortion of
current Ithd

[THDI]

:DISPlay:INTegrate:ITEM<x>

Description

Sets or returns an Integrate measurement data
display item.

Syntax

:DISPlay:INTegrate:ITEM<x> <Function>

Query Syntax

:DISPlay:INTegrate:ITEM<x>?

Parameter/

Return parameter

<x>

1 to 2(display)

<Function>

{WHP|WHM|AHP|AHM|U|I }.

Example

:DISPLAY:INTEGRATE:ITEM1 WHP

:DISPLAY:INTEGRATE:ITEM1?

->:DISPLAY:INTEGRATE:ITEM1 WHP

<Function>

Function

T3PM1006 Indicator

WHP

Positive watt hour WP+

[WP+]

WHM

Positive watt hour WP-

[WP-]

AHP

Positive ampere hour q+

[q+]

AHM

Positive ampere hour q

[q-] U Voltage U

[V]

I

Current I

[I]

Set

Query

76

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

COMMAND OVERVIEW

:DISPlay:PAGE

Description

Sets or returns the display page item.

Syntax

:DISPlay:PAGE <Function>

Query Syntax

:DISPlay:PAGE?

Parameter/

Return parameter

<Function>

{MEASurement|ENLArge|INTEgral|
SYSTem_INFO|SYSTem_CONFig|SETUp}

Example

:DISPLAY:PAGE MEASUREMENT

:DISPLAY:PAGE?

->:DISPLAY:PAGE MEASUREMENT

Set

Query

77

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

:HARMonics:THD

Description

Sets or returns the equation used to compute the
THD (total harmonic distortion).

Syntax

:HARMonics:THD {TOTal|FUNDamental}

Query Syntax

:HARMonics:THD?

Parameter/

Return parameter

TOTal

(CSA)

FUNDamental

(IEC)

Example

:HARMONICS:THD FUNDAMENTAL

:HARMONICS:THD?

->:HARMONICS:THD FUNDAMENTAL

Set

Query

HARMonics Command

78

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

COMMAND OVERVIEW

:HOLD

Description

Sets or returns the on/off state of the output hold
feature for display, communication, and other
types of data.

Syntax

:HOLD <Boolean>|{OFF|ON}

Query Syntax

:HOLD?

Parameter

<Boolean>0

OFF

<Boolean>1

ON

Return parameter

0

Turn the hold function off

1

Turn the hold function on

Example

:HOLD OFF

:HOLD?

->:HOLD 0

Set

Query

HOLD Command

79

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

[:INPut]:CFACtor .......................................................... 80

[:INPut]:MODE ............................................................ 80

[:INPut]:VOLTage:RANGe ........................................... 81

[:INPut]:VOLTage:AUTO ............................................. 81

[:INPut]:VOLTage:CONFig .......................................... 82

[:INPut]:CURRent:RANGe ........................................... 82

[:INPut]:CURRent:AUTO ............................................. 83

[:INPut]:CURRent:CONFig .......................................... 83

[:INPut]:RCONfig ......................................................... 84

[:INPut]:SCALing:{VT/PT|CT}:STATe .......................... 84

[:INPut]:SCALing:{VT/PT|CT}:RATio ........................... 85

[:INPut]:SYNChronize.................................................. 85

[:INPut]:FILTer ............................................................. 85

[:INPut]:ZERO .............................................................. 86

[:INPut]:CFACtor

Description

Sets or returns the crest factor.

Syntax

[:INPut]:CFACtor {<NRf>}

Query Syntax

[:INPut]:CFACtor?

Parameter/
Return parameter

<NR1>

3, 6

Example

:INPUT:CFACTOR 3

:INPUT:CFACTOR?

->:INPUT:CFACTOR 3

[:INPut]:MODE

Description

Sets or returns the voltage and current
measurement mode.

Syntax

[:INPut]:MODE {DC|ACDC|AC}

Query Syntax

[:INPut]:MODE?

Set

Query

Set

Query

INPut Commands

80

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

COMMAND OVERVIEW

Parameter/
Return parameter

Select the dc measurement mode.

Select the acdc measurement mode.

Select the ac mode.

Example

:INPUT:MODE DC

:INPUT:MODE?

->:INPUT:MODE DC

[:INPut]:VOLTage:RANGe

Description

Sets or returns the voltage range.

Syntax

[:INPut]:VOLTage:RANGe {<Voltage>}

Query Syntax

[:INPut]:VOLTage:RANGe?

Parameter/
Return parameter

<Voltage>

15, 30, 60, 150, 300, 600(V) when the
crest factor is set to 3.

7.5, 15, 30, 75, 150, 300(V) when the
crest factor is set to 6

Example

:INPUT:VOLTAGE:RANGE 600V

:INPUT:VOLTAGE:RANGE?

->:INPUT:VOLTAGE:RANGE 600.0E+00

[:INPut]:VOLTage:AUTO

Description

Sets or returns the voltage auto range on/off state.

Syntax

[:INPut]:VOLTage:AUTO {<Boolean>}

Query Syntax

[:INPut]:VOLTage:AUTO?

Parameter

<Boolean>0

OFF

<Boolean>1

ON

Return parameter

0

Turn the voltage auto range function off.

1

Turn the voltage auto range function on.

Set

Query

Set

Query

81

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

Example

:INPUT:VOLTAGE:AUTO ON

:INPUT:VOLTAGE:AUTO?

->:INPUT:VOLTAGE:AUTO 1

[:INPut]:VOLTage:CONFig

Description

Sets or returns the valid voltage range.

Syntax

[:INPut]:VOLTage:CONFig {ALL|<Voltage>[,Voltage]…}

Query Syntax

[:INPut]:VOLTage:CONFig?

Parameter/
Return parameter

ALL

All ranges are valid.

<Voltage>

See(:INPut:VOLTage:RANGe).

Example

:INPUT:VOLTAGE:CONFIG 300,150,30

:INPUT:VOLTAGE:CONFIG?

->:INPUT:VOLTAGE:CONFIG 300.0E+00,150.0E+00,

30.0E+00

[:INPut]:CURRent:RANGe

Description

Sets or returns the current range.

Query

[:INPut]:CURRent:RANGe {<Current>}

Query Syntax

[:INPut]:CURRent:RANGe?

Parameter/
Return parameter

<Current>

5, 10, 20, 50, 100, 200, 500(mA)
1, 2, 5, 10, 20(A) when the crest factor is
set to 3.

2.5, 5, 10, 25, 50, 100, 250(mA)

0.5, 1, 2.5, 5, 10(A)when the crest factor is
set to 6

Example

:INPUT:CURRENT:RANGE 20A

:INPUT:CURRENT:RANGE?

->:INPUT:CURRENT:RANGE 20.0E+00

Set

Query

Set

Query

82

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

COMMAND OVERVIEW

[:INPut]:CURRent:AUTO

Description

Sets or returns the current auto range on/off state.

Syntax

[:INPut]:CURRent:AUTO {<Boolean>}

Query Syntax

[:INPut]:CURRent:AUTO?

Parameter

<Boolean>0

OFF

<Boolean>1

ON

Return parameter

0

Turn the current auto range function off.

1

Turn the current auto range function on.

Example

:INPUT:CURRENT:AUTO ON

:INPUT:CURRENT:AUTO?

->:INPUT:CURRENT:AUTO 1

[:INPut]:CURRent:CONFig

Description

Sets or returns the valid current range.

Syntax

[:INPut]:CURRent:CONFig
{ALL|<Current>[,Current]…}

Query Syntax

[:INPut]:CURRent:CONFig?

Parameter/
Return parameter

ALL

All ranges are valid.

<Current>

See(:INPut:CURRent:RANGe).

Example

:INPUT:CURRENT:CONFIG 20,10,1

:INPUT:CURRENT:CONFIG?

->:INPUT:CURRENT:CONFIG 20.0E+00,10.0E+00,

1.0E+00

Set

Query

Set

Query

83

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

[:INPut]:RCONfig

Description

Sets or returns the on/off state of the range
configuration (valid range selection) feature.

Syntax

[:INPut]:RCONfig {<Boolean>|OFF|ON}

Query Syntax

[:INPut]:RCONfig?

Parameter

<Boolean>0

OFF

<Boolean>1

ON

Return parameter

0

Turn the range configuration feature off.

1

Turn the range configuration feature on.

Example

:INPUT:RCONFIG ON

:INPUT:RCONFIG?

->:INPUT:RCONFIG 1

[:INPut]:SCALing:{VT/PT|CT}:STATe

Description

Sets or returns the scaling vt/pt,ct on/off state.

Syntax

[:INPut]:SCALing:{VT/PT|CT}:STATe {<Boolean>}

Query Syntax

[:INPut]:SCALing:{VT/PT|CT}:STATe?

Parameter

<Boolean>0

OFF

<Boolean>1

ON

Return parameter

0

Turn the scaling vt/pt, ct function off.

1

Turn the scaling vt/pt, ct function on.

Example

:INPUT:SCALING:VT:STATE ON

:INPUT:SCALING:VT:STATE?

->:INPUT:SCALING:VT:STATE 1

Set

Query

Set

Query

84

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

COMMAND OVERVIEW

[:INPut]:SCALing:{VT/PT|CT}:RATio

Description

Collectively Sets or returns the vt/pt ratio or ct
ratio.

Syntax

[:INPut]:SCALing:{VT/PT|CT|}:RATio {<NRf>}

Query Syntax

[:INPut]:SCALing:{VT/PT|CT}: RATio?

Parameter/
Return parameter

<NRf>

1.000 to 9999.999

Example

:INPUT:SCALING:VT:RATIO 1

:INPUT:SCALING:VT:RATIO?

->:INPUT:SCALING:VT:RATIO 1

[:INPut]:SYNChronize

Description

Sets or returns the synchronization source.

Syntax

[:INPut]:SYNChronize {VOLTage|CURRent|OFF}

Query Syntax

[:INPut]:SYNChronize?

Parameter/
Return parameter

Select the voltage synchronization source.

Select the current synchronization source.

Select the off synchronization source.

Example

:INPUT:SYNCHRONIZE VOLTAGE

:INPUT:SYNCHRONIZE?

->:INPUT:SYNCHRONIZE VOLTAGE

[:INPut]:FILTer

Description

Sets or returns the filter state.

Syntax

[:INPut]:FILTer {<Boolean>}

Query Syntax

[:INPut]:FILTer?

Set

Query

Set

Query

Set

Query

85

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

Parameter

<Boolean>0

OFF

<Boolean>1

ON

Return parameter

0

Turn the filter function off.

1

Turn the filter function on.

Example

:INPUT:FILTER OFF

:INPUT:FILTER?

->:INPUT:FILTER 0

[:INPut]:ZERO

Description

Sets or returns the zero state.

Syntax

[:INPut]:ZERO {<Boolean>}

Query Syntax

[:INPut]:ZERO?

Parameter

<Boolean>0

OFF

<Boolean>1

ON

Return parameter

0

Turn the zero function off.

1

Turn the zero function on.

Example

:INPUT:ZERO OFF

:INPUT:ZERO?

->:INPUT:ZERO 0

Set

Query

86

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

COMMAND OVERVIEW

:INTegrate:MODE ........................................................87

:INTegrate:FUNCtion ..................................................87

:INTegrate:TIMer .........................................................88

:INTegrate:STARt .........................................................88

:INTegrate:STOP ..........................................................88

:INTegrate:RESet .........................................................88

:INTegrate:STATe ........................................................89

:INTegrate:MODE

Description

Sets or returns the integration mode.

Syntax

:INTegrate:MODE {MANUal | STANdard}

Query Syntax

:INTegrate:MODE?

Parameter/
Return parameter

MANUal

Continuous integration mode.

STANdard

Standard integration mode.

Example

:INTEGRATE:MODE MANUAL

:INTEGRATE:MODE?

->:INTEGRATE:MODE MANUAL

:INTegrate:FUNCtion

Description

Sets or returns the integration function.

Syntax

:INTegrate:FUNCtion {WATT | AMPEre}

Query Syntax

:INTegrate: FUNCtion?

Parameter/
Return parameter

Select the integration function watt.

Select the integration function ampere.

Example

:INTEGRATE:FUNCTION WATT

:INTEGRATE:FUNCTION?

->:INTEGRATE:FUNCTION WATT

Set

Query

Set

Query

INTegrate Commands

87

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

:INTegrate:TIMer

Description

Sets or returns the integration timer value.

Syntax

:INTEGrate:TIMer {<NRf>,<NRf>,<NRf>}

Query Syntax

:INTEGrate:TIMer?

Parameter/
Return parameter

{<NRf>,<NRf>,<NRf>}

0,0,0 to 9999,59,59

First <NRf>

0 to 9999 (hours)

Second <NRf>

0 to 59 (minutes)

Third <NRf>

0 to 59 (seconds)

Example

:INTEGRATE:TIMER 1,0,0

:INTEGRATE:TIMER?

->:INTEGRATE:TIMER 1,0,0

:INTegrate:STARt

Description

Starts integration.

Syntax

:INTegrate:STARt

Example

:INTEGRATE:START

:INTegrate:STOP

Description

Stops integration.

Syntax

:INTegrate:STOP

Example

:INTEGRATE:STOP

:INTegrate:RESet

Description

Resets the integrated value.

Syntax

:INTegrate:RESet

Example

:INTEGRATE:RESET

Set

Query

Set

Set

Set

88

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

COMMAND OVERVIEW

:INTegrate:STATe

Description

Queries the integration status.

Syntax

:INTegrate:STATe?

Example

:INTEGRATE:STATE?

->RESET

Response

Overflow

Integration overflows.

RESET

Integration resets.

RUNNING

Integration is in progress.

STOP

Integration stops.

TIMEUP

Integration stops due to integration
timeout.

Query

89

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

:MEASure:AVERaging:COUNt .................................... 90

:MEASure:MHOLd ...................................................... 90

:MEASure:AVERaging:COUNt

Description

Sets or returns the averaging coefficient.

Syntax

:MEASure:AVERaging:COUNt {<NRf>}

Query Syntax

:MEASure:AVERaging:COUNt?

Parameter/
Return parameter

<NRf>

1, 2, 4, 8, 16, 32, 64

Example

:MEASURE:AVERAGING:COUNT 8

:MEASURE:AVERAGING:COUNT?

->:MEASURE:AVERAGING:COUNT 8

:MEASure:MHOLd

Description

Sets the MAX hold on/off state.

Syntax

:MEASure:MHOLd {<Boolean>}

Query Syntax

MEASure:MHOLd?

Parameter

<Boolean>0

OFF

<Boolean>1

ON

Return parameter

0

Turn the MAX hold function off.

1

Turn the MAX hold function on.

Example

:MEASURE:MHOLD ON

:MEASURE:MHOLD?

->:MEASURE:MHOLD 1

Set

Query

Set

Query

MEASure Commands

90

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

COMMAND OVERVIEW

:NUMeric[:NORMal]:VALue ........................................91

:NUMeric[:NORMal]:NUMBer ....................................92

:NUMeric[:NORMal]:ITEM<x> ....................................92

:NUMeric[:NORMal]:PRESet .......................................94

:NUMeric[:NORMal]:CLEar .........................................96

:NUMeric[:NORMal]:DELete .......................................97

:NUMeric[:NORMal]:HEADer .....................................97

:NUMeric[:NORMal]:VALue

Description

Returns the numeric data.

Syntax

:NUMeric[:NORMal]:VALue?

Example

:NUMERIC:NORMAL:VALUE?

->

103.79E+00,1.0143E+00,105.27E+00,..(omitted)..,50.0
01E+00

Numeric Data
Format

 Measurement values U, I, P, PPPeak, PMPeak, S,

Q, LAMBda, CFU, CFI, FU, FI, UTHD and ITHD

 Integrated values WH, WHP, WHM, AH, AHP and

AHM.
ASCII: <NR3> format. Example: [-]12.345E+00

 Measurement values UPPeak, UMPeak, IPPeak

and IMPeak.
ASCII: <NR3> format. Example: [-]12.34E+00

 Measurement values (PHI)

ASCII: <NR3> = 0~9.9 format. Example:[-]9.9E+00
ASCII: <NR3> = 10~99.9 format.
Example:[-]99.9E+00
ASCII: <NR3> = 100~999.9 format.
Example:[-]999.9E+000

Query

NUMeric Commands

91

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

 Elapsed integration time (TIME)

ASCII: <NR1> format in units of seconds.
Example: 3600 for 1 hour (1:00:00).

 No items (“-----”)

ASCII: NAN (Not A Number)

Error Data

 Data does not exist (the display shows “-----”)

ASCII: NAN (Not A Number)

:NUMeric[:NORMal]:NUMBer

Description

Sets or returns the specified numeric data output
item function.

Syntax

:NUMeric[:NORMal]:ITEM<x> {<Function>}ALL}

Query Syntax

:NUMeric[:NORMal]:NUMBer?

Parameter/
Return parameter

<NRf>

1 to 34(ALL)

Example

:NUMERIC:NORMAL:NUMBER 10

:NUMERIC:NORMAL:NUMBER

->:NUMERIC:NORMAL:NUMBER 10

Note

 If the parameter is omitted from

the :NUMeric[:NORMal]:VALue? command, the
numeric data items from 1 to the specified value
are output in order.

 By default, the number of numeric data items is set

to 3.

:NUMeric[:NORMal]:ITEM<x>

Description

Sets or returns the specified numeric data output
item function.

Syntax

:NUMeric[:NORMal]:ITEM<x> {<Function>}

Query Syntax

:NUMeric[:NORMal]:ITEM<x>?

Set

Query

Set

Query

92

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

COMMAND OVERVIEW

Parameter/
Return parameter

<x>

1 to 34 (item number)

<Function>
{U|UPPeak|UMPeak|I|IPPeak|IMPeak

|P|PPPeak|PMPeak|S|Q|LAMBda|CFU
|CFI|PHI|FU|FI|UTHD|ITHD|WH
|WHP|WHM|AH|AHP|AHM|TIME
|URANge|IRANge}

Example

:NUMERIC:NORMAL:ITEM1 U

:NUMERIC:NORMAL:ITEM1?

->:NUMERIC:NORMAL:ITEM1 U

<Function>

Function

T3PM1006 Indicator

U

Voltage U

[V]

UPPeak

Maximum voltage: U+pk

[V+pk]

UMPeak

Minimum voltage: U-pk

[V-pk]

I

Current I

[I]

IPPeak

Maximum current: I+pk

[I+pk]

IMPeak

Minimum current: I-pk

[I-pk]

P

Active power P

[P]

PPPeak

Maximum power: P+pk

[P+pk]

PMPeak

Minimum power: P-pk

[P-pk]

S

Apparent power S

[VA]

Q

Reactive power Q

[VAR]

LAMBda

Power factor λ

[PF]

CFU

Voltage factor λ

[CFV]

CFV

Current factor λ

[CFI]

PHI

Phase difference Φ

[DEG]

FU

Voltage frequency fu

[VHz]

FI

Current frequency fI

[AHz]

UTHD

Total harmonic distortion of
voltage Uthd

[THDV]

93

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

ITHD

Total harmonic distortion of
current Ithd

[THDI]
WH

Watt hour WP

[WP]

WHP

Positive watt hour WP+

[WP+]

WHM

Positive watt hour WP-

[WP-]

AH

Ampere hour q

[q]

AHP

Positive ampere hour q+

[q+]

AHM

Positive ampere hour q

[q-]

TIME

Integration time

URANge

Voltage range

IRANge

Current range

:NUMeric[:NORMal]:PRESet

Description

Presets the numeric data output item pattern.

Syntax

:NUMeric[:NORMal]:PRESet {<NRf>}

Parameter/
Return parameter

<NRf>

1 to 4
Example

:NUMERIC:NORMAL:PRESET 1

Patterns 1

ITEM<x>

<Function>

1

U

2 I 3

P

Patterns 2

ITEM<x>

<Function>

1

U

2 I 3

P

4 S 5

Q

6

LAMBda

Set

94

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

COMMAND OVERVIEW

7

PHI

8

FU 9 FI

Patterns 3

ITEM<x>

<Function>

1

U

2 I 3

P

4

S

5

Q

6

LAMBda

7

PHI

8

FU 9 FI

10

UPPeak

11

UMPeak

12

IPPeak

13

IMPeak

14

PPPeak

15

PMPeak

Patterns 4

ITEM<x>

<Function>

1

U

2 I 3 P 4

S

5

Q

6

LAMBda

7

PHI

8

FU 9 FI

95

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

10

UPPeak

11

UMPeak

12

IPPeak

13

IMPeak

14

TIME

15

WH

16

WHP

17

WHM

18

AH

19

AHP

20

AHM

21

PPPeaK

22

PMPeaK

23

CFU

24

CFI

25

UTHD

26

ITHD

27

URANge

28

IRANge

:NUMeric[:NORMal]:CLEar

Description

Clears numeric data output items (sets the items to
“-----“).

Syntax

:NUMeric[:NORMal]:CLEar {ALL|<NRf>[,<NRf>]}

Parameter

First <NRf>

1 to 34 (the number of the first item
to clear)

Second <NRf>

1 to 34 (the number of the last item
to clear)

Example

:NUMERIC:NORMAL:CLEAR ALL

Set

96

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

COMMAND OVERVIEW

Note

If the 2nd <NRf> is omitted, the output item specified
by the first and all following output items (up to
number 34) are cleared.

:NUMeric[:NORMal]:DELete

Description

Deletes numeric data output items.

Syntax

:NUMeric[:NORMal]:DELete {ALL|<NRf>[,<NRf>]}

Parameter

First <NRf>

1 to 34 (the number of the first item
to delete)

Second <NRf>

1 to 34 (the number of the last item
to delete)

Example

:NUMERIC:NORMAL:DELETE 1 (Deletes ITEM1 and
shifts ITEM2 and subsequent items forward).

:NUMERIC:NORMAL:DELETE 1,3 (Deletes ITEM1 to
ITEM3 and shifts ITEM4 and subsequent items
forward).:INTEGRATE:RESET

Note

 When output items are deleted, subsequent items

shift forward to fill the empty positions.
Empty positions at the end are set to “-----“.

 If the second <NRf> is omitted, only the output

item specified by the first number is deleted.

:NUMeric[:NORMal]:HEADer

Description

Returns the numeric data header.

Syntax

:NUMeric[:NORMal]:HEADer?

Example

The data names of the items from 1 to the number
specified by the :

NUMeric[:NORMal]:NUMBer command are output in
order.

:NUMERIC:NORMAL:NUMBER 3

:NUMERIC:NORMAL:HEADER?

-> Urms,Irms,P

Set

Query

97

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

:SYSTem:MODel.......................................................... 98

:SYSTem:SERial ........................................................... 98

:SYSTem:VERSion........................................................ 98

:SYSTem:KLOCk .......................................................... 99

:SYSTem:BRIGhtness .................................................. 99

:SYSTem:KEY:BEEPer ................................................ 100

:SYSTem:MODel

Description

Returns the model code.

Syntax

:SYSTem:MODel?

Example

:SYSTEM:MODEL?

->:SYSTEM:MODEL "T3PM1006"

:SYSTem:SERial

Description

Returns the serial number.

Syntax

:SYSTem:SERial?

Example

:SYSTEM:SERIAL?

->:SYSTEM:SERIAL "123456789A"

Note

Returns the No. item string of the system Information
menu.

:SYSTem:VERSion

Description

Returns the firmware version.

Syntax

:SYSTem:VERsion?

Example

:SYSTEM:VERSION?

->"V1.00"

Query

Query

Query

SYSTem Commands

98

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

COMMAND OVERVIEW

Note

Returns the Ver. item string of the system Information
menu.

:SYSTem:KLOCk

Description

Sets or returns the on/off state of the key
protection.

Syntax

:SYSTem:KLOCk {<Boolean>}

Query Syntax

:SYSTem:KLOCk?

Parameter

<Boolean> 0

OFF

<Boolean> 1

ON

Return parameter

0

Turn the key protection function off

1

Turn the key protection function on.

Example

:SYSTEM:KLOCK OFF

:SYSTEM:KLOCK?

->:SYSTEM:KLOCK 0

:SYSTem:BRIGhtness

Description

Sets or returns the brightness level.

Syntax

:SYSTem:BRIGhtness {<NRf>}

Query Syntax

:SYSTem:BRIGhtness?

Parameter/

Return parameter

<NRf>

1to 9

Example

:SYSTEM:BRIGHTNESS 7

:SYSTEM:BRIGHTNESS?

->:SYSTEM:BRIGHTNESS 7

Set

Query

Set

Query

99

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

T3PM1006 User Manual

:SYSTem:KEY:BEEPer

Description

Sets or returns the keyclick beeper state.

Syntax

:SYSTem:KEY:BEEPer {<Boolean>}

Query Syntax

:SYSTem:COMMunicate:LAN:CONFigure?

Parameter

<Boolean> 0

OFF

<Boolean> 1

ON

Return parameter

0

Turn the keyclick beeper function off.

1

Turn the keyclick beeper function on.

Example

:SYSTEM:KEY:BEEPER OFF

:SYSTEM:KEY:BEEPER?

->:SYSTEM:KEY:BEEPER 0

Set

Query

100

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com