Teledyne USB2-GPIB User Manual

923571-00 Rev A

USB2-GPIB Converter

User’s Manual

Foreword

Thank you for purchasing Teledyne LeCroy’s USB2-GPIB Converter (hereafter referred to as
“USB2-GPIB” or “adapter”.)

This manual describes notes on use and basic usage of the USB2-GPIB.

Before using this adapter, please read this manual thoroughly to gain a good understanding
of it. After reading, please keep the manual in a safe place.

© 2013 by Teledyne LeCroy, Inc. All rights reserved.

Teledyne LeCroy is a registered trademarks of Teledyne LeCroy, Inc. Other product or brand
names are trademarks or requested trademarks of their respective holders. Information in
this publication supersedes all earlier versions. Specifications are subject to change
without notice.

923571-00 Rev A
Sept 2013

Table of Contents

Overview .............................................................................................................................. 1

Safety Information.............................................................................................................. 2

Maintenance........................................................................................................................ 2

How to Use the USB2-GPIB............................................................................................. 3

(a) Connection............................................................................................................. 3

(b) Setting up the GPIB.............................................................................................. 4

(c) Communication Status....................................................................................... 5

(d) Firmware Upgrade................................................................................................ 6

Specifications...................................................................................................................... 7

Service .................................................................................................................................. 8

Warranty............................................................................................................................... 8

Certifications....................................................................................................................... 9

Notes

• Parts of the contents of this manual may be modified without prior notice

for improvements in performance and functions.

• Reproduction or reprinting of the contents of this manual without prior

permission from Teledyne LeCroy is prohibited.

• If you have questions about this adapter, please contact Teledyne LeCroy

at [e-mail], 1-800-5-LeCroy.

Overview

The USB2-GPIB Converter enables you to remotely control an oscilloscope from
a PC using standard GPIB commands.

• The GPIB connector conforms to IEEE488.2 standard. Its delimiter setting is
LF+EOI.

• The USB connector conforms to USB 2.0. For details of the GPIB commands,
see the Remote Control Manual on the Teledyne LeCroy website. Note that the
USB2-GPIB does not function as a controller.

• Minimum firmware version required for this device is 6.5.0.x.

1

Safety Information

This symbol may appear on the product to alert you to additional
information contained in the operator’s manual. The corresponding
information in this guide is similarly denoted.

To avoid personal injury or damage to the USB2-GPIB or any equipment
connected to it, review and comply with the following safety precautions.

Use only as intended.

connected to in a manner not specified by the manufacturer(s) may impair the
protection mechanisms.

Connect and disconnect properly. Do not connect or disconnect equipment to
the GPIB connector of the USB2-GPIB during data transfer. The green LED of
the USB2-GPIB stays lit while the communication is in progress. Disconnecting
equipment during this time may result in data corruption or equipment damage.

Do not use in wet/damp or explosive atmospheres.

For indoor use only. The USB2-GPIB is intended for indoor use and should be

operated in a clean, dry, environment.

Do not operate with suspected failures. Do not use USB2-GPIB if any part is
damaged. All maintenance should be referred to qualified service personnel.

Keep product surfaces clean and dry.

Use of the USB2-GPIB and/or the equipment it is

Maintenance

USB2-GPIB is a high quality, precision adapter. To maintain accuracy and
signal fidelity, avoid mechanical shock, as well as damage to the cable through
excessive bending. It is recommended to inspect cables before use to ensure they
are in good condition and are properly connected. Poor cables and/or connection
will result in data corruption.

Refer all maintenance and component replacement to qualified personnel. Do not
remove external covers in an attempt to clean internal parts.

Clean the outside of the USB2-GPIB with a soft cloth dampened with either
deionized / distilled water or isopropyl alcohol. Allow the surface to dry
completely before returning the adapter to service.

2

923571-00 Rev A