DCT1800 SERIES DIAGRAM
DCT1800 SERIES USERS GUIDE
1.8 GHz DECT Single-Line Digital Cordless Telephone
CONTACTING TELEDEX
Telephone
+1.408.363.3100
Part Number 600-0480-72 Copyright © 2006 Teledex LLC. ALL RIGHTS RESERVED.
Internet
www.teledex.com
Email
sales@teledex.com
Mailing Address
6311 San Ignacio Avenue
San Jose, CA 95119 USA
INCLUDED IN YOUR PACKAGE
Cordless Handset AC Adapter
Base Unit User Guide
Battery Pack RJ-11 Line Cord
Rubber Battery Screw Cover RJ-45 Cable
Phillips Screw Clear Plastic Overlay
PREPARING TO USE THE DCT1800 SERIES
1. Prepare to install the battery into the cordless handset by
firmly pressing down on the top of the battery cover and
sliding it off. If cover is secured with a screw,remove the
screw first.
2. Locate the lightly embossed numbers “1” and “2” on the
battery’s plastic connector.
3. Insert the battery connector into the handset’s connector
with the embossed numbers facing up.
Note: The handset may “beep” when the battery is connected. This is not
an indication that the telephone is ready to use.To obtain optimal performance of the telephone, be sure to charge the battery for 15 to 20 hours.
4. Replace the battery compartment cover and retaining screw.
5. Insert the provided rubber screw cover.
6. Turn the telephone base so the back panel is facing you.
Insert either end of the RJ-45 cable into the jack on the back
of the telephone labeled
7. Insert the other end of the cable into the jack on the AC
adapter labeled
8. Insert one end of the RJ-11 line cord into the jack on the AC
adapter labeled
9. Insert the other end of this line cord into a telephone jack.
10. Plug the AC adapter into an unswitched
11.Once your telephone is connected, remove the plastic
overlay and place the paper faceplate over the keys. Replace
the plastic overlay by hooking the tabs on the overlay into
the recessed slots located on both sides.The overlay is
easiest to insert when the left or right side tabs are inserted
first, and the middle of the overlay is slightly bowed to allow
for insertion of the other tabs.
12.Place the cordless handset on the base unit.
CHARGING THE BATTERY
The rechargeable battery must be fully charged before using the
phone for the first time. It is recommended that that battery pack
be charged for approximately 15 to 20 hours, without interruption,
before use.To charge the battery,place the handset, keypad down,
in the base unit. Make sure the
If the LED does not light:
1. Ensure that the AC adapter is plugged in.
2. Ensure that the AC adapter is not
electrical outlet.
LINE.
PHONE.
LINE.
electrical outlet.
CHARGE LED on the base lights.
plugged into a switched
3. Ensure that the handset charging contacts at the bottom of
the handset are making good contact with the base unit’s
charging contacts.
CLEANING THE BATTERY CONTACTS
To maintain a good charge, it is important to clean all charging
contacts on the handset and base unit. Use a pencil eraser or
other contact cleaner.
BATTERY SAFETY INSTRUCTIONS
1. Use only Teledex-approved battery replacements.
2. Dispose of used batteries according to local codes pertaining
to rechargeable batteries.
3. Do not dispose of batteries in fire, as they may explode
4. Charge the telephone's batteries only while in the telephone
handset, and only by using the telephone base unit to charge.
Do not attempt to remove the batteries and charge them in
a separate charging unit.
5. Do not short-circuit the battery pack, as this may cause it to
explode or catch fire.
HANDSET/BASE REGISTRATION PROCEDURE
This procedure establishes an exclusive link between a specific
handset and base, thereby allowing no other access to this
specific base.To accomplish this procedure, place the handset
on the base in the charging position. The
blink while the process is occuring. This process occurs each
time the handset is placed on the base in the charging cradle.
ADJUSTING THE RING VOLUME
The up and down volume keys will adjust the ringer volume of
the telephone.Additionally, the DCT1800 series telephone has
an optional “courtesy” ring mode, wherein the ring volume
begins at the lowest setting, then automatically rings louder
with each successive ring during an incoming call. To select the
courtesy ring mode, follow these steps:
Press the
the
To return to regular ring mode:Press the
key; then the STORE key; then the 1 key.
ADJUSTING SPEAKERPHONE VOLUME
The speakerphone has eight (8) levels. To adjust speakerphone
volume, locate the volume up/down keys, located on the front
surface of the phone below the keypad.With the speaker active,
press the “down” arrow key to decrease the volume level, and
press the “up” arrow key to increase it.
FLASH key; then the 4 key; then the STORE key; then
1 key.
Do not use any liquids or solvents.
LINE indicator will
FLASH key; then the 1
ADJUSTING HANDSET RECEIVE VOLUME
The handset has eight (8) volume levels.To adjust the handset
volume, locate the volume up/down keys, located on the
handset, below the “
decrease the volume level, while pressing the “plus”
#” key. Pressing the “minus” (-) key will
(+) key
will increase it.
AUTO DIAL KEYS
The DCT1800 series has either five (5) or ten (10) programmable
guest service (auto dial) keys,depending on the model you own.
These keys can be programmed to automatically dial telephone
numbers, or to activate telephone system features. To program the
auto dial keys (programming can only be done from base unit
):
1. With the phone “on hook” (inactive) and the faceplate
removed, press the recessed
STORE key (see diagram).
2. Enter the desired telephone number (up to 15 digits in
length) to be stored. To enter a “pause” in the number
string, press the
3. Press the
REDIAL key as necessary.
STORE key again.
4. Press the auto dial key where the number is to be stored.
Programming is now completed for that auto dial key.
To program additional keys, repeat this process.
RECEIVING A CALL
An audible ring and flickering red LED indicate an incoming call.
o answer the call using the handset while it is not on the base:
T
1. Pick up the handset and press the ON key.
2. The handset will go “off-hook”answering the call.
3. To end the call,place the handset in the base unit cradle, or
press the
o answer the call using the handset while it is resting on the base:
T
OFF key on the handset.
1. Pick up the handset from the base.The phone will
automatically connect to the line.
2. To end the call,replace the handset in the base unit cradle,
or press the
o answer the call using the speakerphone:
T
OFF key on the handset.
1. Press either the LINE key or the SPKR key. The speakerphone
will go “off-hook” answering the call.
2. To end the call, press the
SPKR key to hang up.
PLACING A CALL
Using the handset:
1. Pick up the handset and press the ON key. Listen for dial
tone and dial the desired number.
2. After the call is complete, press the
Using the speak
erphone:
OFF key to hang up.
1. Press either the LINE key or the SPKR key.
2. Listen for dial tone, and dial the desired number, or press an
auto dial key to dial a preprogrammed number.
3. After the call is complete, press the
SPKR key to hang up.
REDIAL
The DCT1800 series can automatically redial the last number
dialed. On the handset, press the
REDIAL key to redial the last
number.
USING THE HOLD KEY
The HOLD key places the call on hold locally at the cordless
telephone.
o place a call on hold:
T
1. With a call active, press the red HOLD key on either the
handset or base unit.
2. The red line LED will flash, indicating the call is on hold.
T
o remove a call from hold:
1. Press the line key of the call on hold.This will remove the
call from hold, making the call active again.
2. The red line LED will return to steady illumination, indicating
the line is active.
T
o change phones after placing a call on hold:
1. Place the call on hold as above.
2. Pick up the call at another telephone that is on the same
line.The telephone will activate the line and remove the hold
at the original telephone.
TO MUTE THE SPEAKERPHONE
1. Press the MUTE key on the base unit.The red LED above
the
MUTE key will illuminate. The party on the other end
will not be able to hear you when the
2. Press the
The
MUTE key again to turn off the mute feature.
MUTE LED will go out.
MUTE LED is lit.
CONVERTING FROM DESK TO WALL MOUNT
The DCT1800 series can be adapted for wall mounting applications.The conversion is easiest to make when the handset and
cords are not connected.
1. Located on the handset cradle, above the speaker grill, is the
wall/desk mount clip. Remove this clip by firmly pushing it
upward towards the top of the phone.
2. Flip the clip over (top to bottom) so that the protruding edge is
towards the top of the phone and replace it in its slot.This edge
will hold the handset when the phone is mounted on the wall.
3. Turn the telephone over so the bottom is up, facing you.
Place it on a non-abrasive surface to prevent scratching.
4. Locate and remove the mounting bracket. Firmly push back
and pull up to remove two of the four retaining tabs.
5. Rotate the mounting bracket 180º degrees clockwise
, so that
the mounting eyelet on the bracket is facing in the same
direction as the other mounting eyelet located on the
bottom of the telephone.
6. Insert the top two retaining tabs of the mounting brackets
into the mounting bracket slots (located near the middle of
the telephone). Then firmly push down to insert the retaining
tabs on the opposite side of the mounting bracket.
7. Connect a 15-foot RJ-45 cord into the
LINE jack on the back
of the phone.
8. Turn the telephone over, and slide the telephone down onto
the mounting posts of the wall bracket. Ensure that both
eyelets line up with the mounting posts.
IMPORTANT SAFETY INSTRUCTIONS
WHEN USING YOUR TELEPHONE EQUIPMENT, BASIC SAFETY PRECAUTIONS
SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE,ELECTRIC SHOCK
AND INJURY TO PERSONS, INCLUDING THE FOLLOWING:
1. READ AND UNDERSTAND ALL INSTRUCTIONS.
2. FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE PRODUCT.
3. UNPLUG THE PRODUCT FROM THE WALL OUTLET BEFORE CLEANING.DO
NOT USE LIQUID CLEANER OR AEROSOL CLEANERS. USE A DAMP CLOTH FOR
CLEANING.
4. DO NOT USE THIS PRODUCT NEAR WATER,FOR EXAMPLE, NEAR A BATHTUB,WASH BOWL,KITCHEN SINK OR LAUNDRY TUB, IN A WET BASEMENT, OR
NEAR A SWIMMING POOL.
5. DO NOT PLACE THIS PRODUCT ON AN UNSTABLE CART,STAND OR TABLE.
THE PRODUCT MAY FALL, CAUSING SERIOUS DAMAGE TO THE PRODUCT.
6. SLOTS AND OPENINGS IN THE CABINET AND THE BACK OF BOTTOM ARE
PROVIDED FOR VENTILATION, TO PROTECT IT FROM OVERHEATING. THESE
OPENINGS MUST NOT BE BLOCKED OR COVERED. THE OPENINGS SHOULD
NEVER BE BLOCKED BY PLACING THE PRODUCT ON THE BED, SOFA, RUG OR
ANY OTHER SIMILAR SURFACE. THIS PRODUCT SHOULD NEVER BE PLACED
NEAR OR OVER A RADIATOR OR HEAT REGISTER.THIS PRODUCT SHOULD NOT
BE PLACED IN A BUILT-IN INSTALLATION UNLESS PROPER VENTILATION IS
PROVIDED.
7. NEVER PUSH OBJECTS OF ANY KIND INTO THIS PRODUCT THROUGH CABINET SLOTS AS THEY MAY TOUCH DANGEROUS VOLTAGE POINTS OR SHORT
OUT PARTS THAT COULD RESULT IN A RISK OF FIRE OR ELECTRIC SHOCK.
NEVER SPILL LIQUID OF ANY KIND ON THE PRODUCT.
8. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT DISASSEMBLE THIS
PRODUCT. BUT TAKE IT TO A QUALIFIED SERVICE FACILITY IF
SERVICE OR REPAIR WORK IS REQUIRED. OPENING OR REMOVING COVERS
MAY EXPOSE YOU TO DANGEROUS VOLTAGES OR OTHER RISKS. INCORRECT
REASSEMBLY CAN CAUSE ELECTRIC SHOCK WHEN THE APPLIANCE IS SUBSEQUENTLY USED.
9. UNPLUG THIS PRODUCT FROM THE WALL OUTLET AND REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL UNDER THE FOLLOWING CONDITIONS:
- WHEN THE POWER SUPPLY CORD OR PLUG IS DAMAGED OR FRAYED.
- IF LIQUID HAS BEEN SPILLED INTO THE PRODUCT.
- IF THE PRODUCT HAS BEEN EXPOSED TO RAIN OR WATER.
- IF THE PRODUCT DOES NOT OPERATE NORMALLY BY FOLLOWING THE
OPERATING INSTRUCTIONS. ADJUST ONLY THOSE CONTROLS THAT ARE COVERED BY THE OPERATING INSTRUCTIONS, AS IMPROPER ADJUSTMENT OF
OTHER CONTROLS MAY RESULT IN DAMAGE,AND MAY REQUIRE EXTENSIVE
WORK BY A QUALIFIED TECHNICIAN TO
RESTORE THE PRODUCT TO NORMAL OPERATION.
- IF THE PRODUCT HAS BEEN DROPPED OR THE CABINET HAS BEEN DAMAGED.
- IF THE PRODUCT EXHIBIT A DISTINCT CHANGE IN PERFORMANCE.
10. AVOID USING A TELEPHONE (OTHER THAN A CORDLESS TYPE)
DURING AN ELECTRICAL STORM.THERE MAY BE A REMOTE RISK OF ELECTRIC
SHOCK FROM LIGHTNING.
11. DO NOT USE THE TELEPHONE TO REPORT A GAS LEAK IN THE
VICINITY OF THE LEAK.
PLEASE SAVE THESE INSTRUCTIONS
Loading...