Tektronix WFM200BC Instructions Manual

xx

General safety summary

Use the product only as specified. Review the following
safety precautions to avoid injury and prevent damage to this
product or any products connected to it. Carefully read all
instructions. Retain these instructions for future reference.

Comply with local and national safety codes.

For correct and safe operation of the product, it is essential
that you follow generally accepted safety procedures in
addition to the safety precautions specified in this manual.

The product is designed to be used by trained personnel only.

This product is not intended for detection of hazardous
voltages.

To avoid fire or personal injury

Use pro per power cord.

Use only the power cord specified

for this product and certified for the country of use.

Ground the product.

This product is indirectly grounded
through the grounding conductor of the mainframe power
cord. To avoid electric shock, the grounding conductor must
be connected to earth ground. Before making connections
to the input or output terminals of the product, make sure
that the product is properly grounded.

Do not disable the power cord grounding connection.

Power disconnect.

Remove the power cord of the external
AC adapter to disconnect mains power from the product.
Do not position the charger so that it is difficult to operate
the power cord; it must remain accessible to the user at all
times to allow for quick disconnection if needed.

Use proper AC adapter.

Use only the AC adapter specified

for this product.

Use proper battery charger.

Use only the WFM200BC
charger or a Tektronix WFM2200, WFM2200A, or
WFM2300 waveform monitor to charge the WFM200BA
Lithium-Ion battery pack.

Do not operate without covers.

Do not operate this product

with covers or panels removed.

Do not operate with suspected failures.

If you suspect there
is damage to this product, have it inspected by qualified
service personnel.

Disable the product if it is damaged. Do not use the product
if it is damaged or operates incorrectly. If in doubt about
safety of the product, turn it off and disconnect the power
cord. Clearly mark the product to prevent its further
operation.

Examine the exterior of the product before you use it. Look
for cracks or missing pieces.

Avoid exposed circuitry.

Do not touch exposed connections

and components when power is present.

Recharge batteries properly.

Recharge batteries for the

recommended charge cycle only.

Do not operate in wet/damp conditions.

Be aware that
condensation may occur if a unit is moved from a cold to
a warm environment.

Keep product surfaces clean and dry.

Do not attempt to service this product.

There are no

serviceable components in the WFM200BC battery charger.

Safety terms in this manual

WARN IN G.

Warning statements identify conditions or

practices that could result in injury or loss of life.

CAUTION.

Caution statements identify conditions or
practices that could result in damage to this product or
other property.

Symbols a nd terms on the product

These terms may appear on the product:

DANGER indicates an injury hazard immediately
accessible as you read the marking.

WARNING indicates an injury hazard not immediately
accessible as you read the marking.

CAUTION indicates a hazard to property including
the product.

Compliance information

This section lists the EMC (electromagnetic compliance),
safety, and environmental standards with which the
WFM200BC charger complies. Compliance demonstrated
using high quality, shielded interface cables.

EMC compliance

EC Decl aration of Conformity – EMC

Meets the intent of Directive 2004/108/EC for
Electromagnetic Compatibility. Compliance was
demonstrated to the following specifications as listed in the
Official Journal of the European Communities:

EN 55103-1:2009 Environmental E2.

Product family
standard for audio, video, audio-visual. Industrial and light
commercial

1

Part 1 Emission

EN 55022:2006 Class B – Radiated and conducted
emissions

EN 55103-1:2009 Annex A – Radiated magnetic
field emissions

Part 2 Immunity

EN 55103-2:2009 Annex A – Radiated magnetic
field immunity

IEC 61000-4-11:2004 – Power line voltage dip and
interruption immunity

IEC 61000-4-2:2000 – Electrostatic discharge
immunity

IEC 61000-4-3:2007 – RF electromagnetic field
immunity

IEC 61000-4-4:2004 – Electrical fast transient /
burst immunity

IEC 61000-4-5:2005 – Power line surge immunity

IEC 61000-4-6:2006 – RF conducted immunity

1

Average half-cycle r.m.s. Inrush current at initial switch on : 2.8 A. Average
half-cycle r.m.s. Inrush current after 5 second power interruption: 2.4 A.

EN 61000-3-2:20 06.

AC power line harmonic emissions

EN 61000-3-3:1995.

Voltage changes, fluctuations, and

flicker

WFM200BC
External Battery Charger

ZZZ

Instructions

x

*P075104202*

075-1042-02

European contact.

Tektronix UK, Ltd.
Western Peninsula
Wes te r n R oa d
Bracknell, RG12 1RF
United Kingdom

Australia / New Zealand Declaration of Conformity – EMC

Complies with the EMC provision of the Australia
Radiocommunications Act 1992 per the following standard,
in accordance with ACMA:

EN 55022:2006 Class B – Radiated and conducted
emissions, in accordance with EN 55103-1:2009

Supplier Code: N60

Australia / New Zealand contact.

Baker & McKenzie
Level 27, AMP Centre
50 Bridge Street
Sydney NSW 2000, Australia

Environmental considerations

This section provides information about the environmental
impact of the product.

Product end-of-life handling

Observe the following guidelines when recycling an
instrument or component:

Equipment recycling.

Production of this equipment required
the extraction and use of natural resources. The equipment
may contain substances that could be harmful to the
environment or human health if improperly handled at the
product’s end of life. In order to avoid release of such
substances into the environment and to reduce the use of
natural resources, we encourage you to recycle this product
in an appropriate system that will ensure that most of the
materials are reused or recycled appropriately.

This symbol indicates that this product
complies with the applicable European
Union requirements according to Directives
2002/96/EC and 2006/66/EC on waste
electrical and electronic equipment (WEEE)
and batteries. For information about recycling
options, check the Support/Service section of
the Tektronix Web site (www.tektronix.com).

Restriction of hazardous substances

This product is classified as an industrial monitoring and
control instrument accessory, and is not required to comply
with the substance restrictions of the recast RoHS D irective
2011/65/EU until July 22, 2017.

Product description

The Tektronix WFM200BC External Battery Charger
is intended for use with only the Tektronix Lithium-Ion
WFM200BA Rechargeable Battery Pack.

NOTE.

Refer to the WFM200BA Rechargeable Battery
Pack Instructions (Tektronix part number 075-1041-XX)
for information on storage, transportation, and end-of-life
recycling or disposal of the Lithium-Ion battery pack.

International power cords

Your product was shipped with one of the following power
cord options. Power cords for use in North America are
UL listed and CSA certified. Cords for use in areas other
than North America are approved by at least one authority
acceptable in the country to which the product is shipped.

Opt. A0 – North America power

Opt. A1 – Universal EUR power

Opt. A2 – United Kingdom power

Opt. A3 – Australia power

Opt. A5 – Switzerland power

Opt. A6 – Japan power

Opt. A10 – China power

Opt. A11 – India power

Opt. A12 – Brazil power

Opt. A991– No power cord

1

When ordering the A99 option, it is the responsibility of the end user to be
sure that a certified power cord, for the country or region in which it is
installed, is used with this product.

CAUTION.

To reduce risk of fire and shock, use the

certified power cord provided with the product.

Battery pack charging

For optimum performance, charge the battery pack
completely before using it for the first time or after
prolonged storage.

CAUTION.

To avoid damage to the product or to other
battery packs, do not use the WFM200BC external
battery charger on any battery pack other than the
WFM200BA battery pack.

To avoid damage to the WFM200BA battery pack, use
only a Tektronix WFM2200, WFM2200A, or WFM2300
waveform monitor or the WFM200BC External Battery
Charger to charge the battery pack. Do not connect any
other voltage source to the battery pack.

To avoid overheating of the batteries during charging,
do not exceed the maximum ambient temperature of
40 °C.

Perform the following steps to charge the WFM200BA
battery pack:

1.

Connect the AC adapter power supply to a mains outlet
and insert t he DC plug of the power supply into the
WFM200BC External Battery Charger.

2.

Align the slots on the battery to the slots in the charger
and insert the battery into one of the charger bays.

3.

Note the condition of the charger LEDs:

LED condition Description

Solid green Power on / Battery fully

charged

Flashing green Battery is charging

Solid red Battery fault

Specifications

Characteristic Description

Output 16.8 VDC

Charge time

5.5 hrs

Adapter requirements

19 V / 3.16 A typical

DC input voltage
range

18–24 V

Operating
temperature

10°Cto+40°C(+50°Fto+104°F)

Storage temperature -20 °C to +60 °C (-4 °F to +140 °F)

Warranty information

For warranty information, go to the www.tektronix.com
Web site, and search for “WFM200BC warranty”.

Contacting Tektronix

Tektronix, Inc.
14200 SW Karl Braun Drive
P.O. Box 500
Beaverton, OR 97077
USA

For product information, sales, service, and technical
support:

In North America, call 1-800-833-9200.

Worldwide, visit www.tektronix.com to find contacts
in your area.

Copyright © Tektronix, Inc. All rights reserved. www.tektronix.com