Tektronix TLA5201, TLA5202, TLA5203, TLA5204, TLA5201B Performance Verification

...

TLA5200 Series Logic Analyzer

ZZZ

Product Speciﬁcations & Performance Veriﬁcation

Technical Reference

*P077250201*

077-2502-01

TLA5200 Series Logic Analyzer

ZZZ

Product Speciﬁcations & Performance Veriﬁcation

Technical Reference

This document applies to TLA System Software Version

5.1SP1 and above

Warning

These servicing instructions are for use by qualiﬁed personnel only. To avoid personal injury, do not perform any servicing unless you are qualiﬁed to do so. Refer to all safety summaries prior to performing service.

www.tektronix.com

077-2502-01

Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or suppliers, and are protected by national copyright laws and international treaty provisions.

Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all previously published material. Speciﬁcations and price change privileges reserved.

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

MagniVu and iView are registered trademarks of Tektronix, Inc.

Contacting Tektronix

Tektronix, Inc. 14200 SW Karl Braun Drive P.O . Bo x 50 0 Beaverton, OR 97077 USA

For product information, sales, service, and technical support:

In North America, call 1-800-833-9200. World wi de, v i sit www.tektronix.com to ﬁnd contacts in your area.

Table of Contents

General Safety Summary ......................................................................................... iv

Service Safety Summary.......................................... ................................ ................ vi

Preface ............................................................................................................. vii

Related Doc

Speciﬁcations .................. .................................. ................................ ................... 1

External Oscilloscope (iView) Characteristics ..................... ................................ ............ 15

Performance Veriﬁcation Procedures............................................................................ 17

Summary Veriﬁcation ........................................................................................ 17

Certiﬁcation . ................................ ................................ .................................. 17

Test Equ

Functional Veriﬁcation ....... ................................ .................................. .............. 19

Performance Veriﬁcation........................... ................................ .......................... 21

Checking the 10 MHz System Clock (CLK10) . ................................ .......................... 22

Threshold Accuracy .......................................................................................... 23

Setup and Hold.................................... .................................. .......................... 26

Fixtures.................. .................................. ................................ .................... 30

Test

Threshold Accuracy Test Fixture ........................................................................... 30

Setup and Hold Test Fixture ............................... ................................ .................. 31

Calibration Data Report........................................... ................................ ................ 33

TLA5200 Series............................................................................................... 33

Test Data....................................................................................................... 33

umentation ..................................................................................... vii

ipment................................ .................................. .............................. 18

TLA5200 Series Product Speciﬁcations & Performance Veriﬁcation i

Table of Contents

List of Figure

Figure 1: Dimensions of the TLA5200 series logic analyzer................. ................................ 14

Figure 2: De

Figure 3: Setting trigger parameters . ... ... . ... ... . ... ... . ... ... . .. . ... ... . ... ... . ... ... . ... ... . ... ... . .. . ... .... 24

Figure 4: Set the trigger states ............................. .................................. .................... 28

Figure 5: Threshold Accuracy test ﬁxture ...................................................................... 30

Figure 6: Solder square pins to the SMA connector......... ................................ .................. 31

Figure 7: Solder the SMA connectors together ........................ ................................ ........ 32

Figure 8:

ﬁning group parameters............................................................................ 23

Completed ﬁxture with termination and coupler ..... .................................. ............ 32

ii TLA5200 Series Product Speciﬁcations & Performance Veriﬁcation

List of Tables

Table i: Related Documentation ............. ................................ ................................ ... vii

Table 1: Atm

Table 2: TLA5200 input parameters with probes ...................... ................................ ......... 2

Table 3: TLA5200 timing latencies .............................................................................. 2

Table 4: TLA5200 external signal interface........................ ................................ ............. 3

Table 5: TLA5200 channel width and depth .................................................................... 5

Table 6: Reference clock (CLK10) ........................ ................................ ....................... 5

Table 7: T

Table 8: TLA5200 trigger system ................................................................................ 8

Table 9: TLA5200 MagniVu feature ............................................................................ 10

Table 10: TLA5200 Data Placement ............................................................................ 10

Table 11: TLA5200 Data handling .............................................................................. 11

Table 12: TLA5200B internal controller........................................................................ 11

13: TLA5200 internal controller.......................................................................... 11

Table

Table 14: TLA5200 display system ....... ................................ ................................ ...... 12

Table 15: TLA5200 front-panel interface....................................................................... 13

Table 16: TLA5200 rear-panel interface...................................... .................................. 13

Table 17: TLA5200 AC power source ...... .................................. ................................ .. 13

Table 18: TLA5200 cooling...................................................................................... 13

ble 19: TLA5200 mechanical characteristics................................................................ 14

Table 20: External oscilloscope (Integrated View or iView) characteristics. . ... ... . ... ... . ... ... . ... ... . .. 15

Table 21: TDS1000, TDS1000B, TDS2000, and TDS2000B Series oscilloscope waveform edge

alignment ...................................................................................................... 16

Table 22: Test equipment ....................... ................................ ................................ .. 18

Table 23: Functional veriﬁcation procedures....................... .................................. .......... 19

Table 24: Parameters checked by veriﬁcation procedures .................................................... 21

ospheric characteristics............................................................................. 1

LA5200 clocking ....................................................................................... 6

Table of Contents

TLA5200 Series Product Speciﬁcations & Performance Veriﬁcation iii

General Safety Summary

General Safet

To Avoid Fire or Person al

Injury

ySummary

Review the fo this product or any products connected to it.

To avoid potential hazards, use this product only as speciﬁed.

Only qualiﬁed personnel should perform service procedures.

While using this product, you may need to access other parts of a larger system. Read the safety sections of the other component manuals for warnings and cautions related to operating the system.

Use Proper Power Cord. Use only the power cord speciﬁed for this product and certiﬁed for the country of use.

Connect and Disconnect Properly. Do not connect or disconnect probes or test leads while they are connected to a voltage source.

Ground the Product. This product is grounded through the grounding conductor of the power cord. To avoid electric shock, the grounding conductor must be connected to eart terminals of the product, ensure that the product is properly grounded.

llowing safety precautions to avoid injury and prevent damage to

h ground. Before making connections to the input or output

Observe All Terminal Ratings. To avoid ﬁre or shock hazard, observe all ratings and markings on the product. Consult the product manual for further ratings information before making connections to the product.

The inputs are not rated for connection to mains or Category II, III, or IV circuits.

Power Disconnect. The power cord disconnects the product from the power source. Donotblockthepowercord;itmustremain accessible to the user at all times.

Do Not Operate Without Covers. Do not operate this product with covers or panels removed.

Do Not Operate With Suspected Failures. If you suspect that there is damage to this product, have it inspected by qualiﬁed service personnel.

Avoid Exposed Circuitry. Do not touch exposed connections and components when power is present.

Use Proper Fuse. Useonlythefusetypeandratingspeciﬁed for this product.

Do Not Operate in Wet/Damp Conditions.

Do Not Operate in an Explosive Atmosphere.

Keep Product Surfaces Clean and Dry.

Provide Proper Ventilation. Refer to the manual’s installation instructions for

details on installing the product so it has proper ventilation.

iv TLA5200 Series Product Speciﬁcations & Performance Veriﬁcation

General Safety Summary

Terms in this Manual

Symbols and Terms on the

Product

These terms may

WAR N ING. Warning statements identify conditions or practices that could result

in injury or loss of life.

CAUTION. Caution statements identify conditions or practices that could result in

damage to this product or other property.

These terms may appear on the product:

DANGER in the marking.

WAR NI NG read the marking.

CAUTIO

The following symbol(s) may appear on the product:

appear in this manual:

dicates an injury hazard immediately accessible as you read

indicates an injury hazard not immediately accessible as you

N indicates a hazard to property including the product.

TLA5200 Series Product Speciﬁcations & Performance Veriﬁcation v

Service Safety Summary

Service Safet

y Summary

Only qualiﬁe Safety Summary and the General Safety Summary before performing any service procedures.

Do Not Service Alone. Do not perform internal service or adjustments of this product unless another person capable of rendering ﬁrst aid and resuscitation is present.

Disconnect Power. To avoid electric shock, switch off the instrument power, then disconnect the power cord from the mains power.

Use Care When Servicing With Power On. Dangerous voltages or currents may exist in disconnect test leads before removing protective panels, soldering, or replacing components.

To avoid electric shock, do not touch exposed connections.

d personnel should perform service procedures. Read this Service

this product. Disconnect power, remove battery (if applicable), and

vi TLA5200 Series Product Speciﬁcations & Performance Veriﬁcation

Preface

Related Documentation

This document lists the characteristics and speciﬁcations of the TLA5200 and TLA5200B series logic analyzers. It also includes the performance veriﬁcation procedures. otherwise noted. Microprocessor-related products and individual logic analyzer probes have their own documentation for characteristics and speciﬁcations.

To prevent personal injury or damage consider the following requirements before attempting service:

The procedures in this manual should be performed only by qualiﬁed service personnel.

Read the General Safety Summary and Service Safety Summary found at the beginning of this manual.

Be sure to follow all warnings, cautions, and notes in this manual.

The following table lists related documentation available for your logic analyzer. The documentation is available on the TLA Documentation CD included with your logic analyzer, and on the Tektronix Web site (www.Tektronix.com).

All references to TLA5200 also apply to TLA5200B, unless

To obtain documentation not speciﬁed in the table, contact your local Tektronix representative.

Table i: Related Documentation

Item Purpose Location

TLA Quick Start User Manual

Online Help

Installation Quick Reference Cards Basic installation information

Installation Manuals

YZs of Logic A nalyzers

TLA Product Speci ﬁcations Speciﬁcations for other TLA products

Basic operational overview

In depth operation and UI help

Detailed ﬁrst-time installation information

Introduction to logic analyzer basics

TLA5200 Series Product Speciﬁcations & Performance Veriﬁcation vii

Preface

Table i: Related Documentation (cont.)

Item Purpose Location

TPI.NET Documentation

Detailed information for controlling the logic analyzer u sing .NET

Field upgrade kits

Optional Service Manuals Self-service documentation for modules

TLA Application Software Release N otes Software description, compatibility,

Upgrade information for your logic analyzer p

and mainframes

impact of installation, upgrade, and operational notes, and known issues.

roduct

changes, contact information,

Go to Start→All Programs→Tektronix logic Analyzer→TLA Release Notes

viii TLA5200 Series Product Speciﬁcations & Performance Veriﬁcation

Speciﬁcations

The following tables list the speciﬁcations for the TLA5200B and TLA5200 series logic analyzers. All references to TLA5200 also apply to TLA5200B, unless otherwise no

ted. All speciﬁcations are guaranteed unless noted Typ i ca l . Typical characteristics describe typical or average performance and provide useful reference information.

Speciﬁcations that are marked with the indirectly) in the Performance Veriﬁcation chapter of this document.

The performance limits in this speciﬁcation are valid with these conditions:

For op documentation for any external oscilloscopes used with your Tektronix logic analyzer to determine the warm-up period and signal-path compensation requirements.

Table 1: Atmospheric characteristics

racteristic

Cha

Temperature

Relative humidity

Altitude

cription

Des

rating (no media in CD or DVD drive)

Ope

°C to +50 °C, 15 °C/hr m aximum gradient, noncondensing (derated 1 °C per 305 m (1000 ft)

+5 above 1524 m (5000 ft) altitude)

Nonoperating (no media in drive)

-20 °C to +60 °C, 15 °C/hr maximum gradient, noncondensing

Operating (no media in drive)

20% to 80% relative humidity, noncondensing. Maximum wet bulb temperature: +29 °C (derates relative humidity to approximately 22% at +50 °C).

Nonoperating (no media in drive)

8% to 80% relative humidity, noncondensing. Maximum wet bulb temperature: +29 °C (derates relative humidity to approximately 22% at +50 °C).

Operating

To 3000 m (9843 ft), (derated 1 °C per 305 m (1000 ft) above 1524 m (5000 ft) altitude.

Nonoperating

12,190 m (40,000 ft )

symbol are checked directly (or

The instr

ument must be in an environment with temperature, altitude, humidity, and vibration within the operating limits described in these speciﬁcations.

The instrument must have had a warm-up period of at least 30 minutes.

The ins

trument must have been calibrated/adjusted at an ambient temperature

between +20 °C and +30 °C.

timum performance using an external oscilloscope, please consult the

TLA5200 Series Product Speciﬁcations & Performance Veriﬁcation 1

Speciﬁcations

Table 2: TLA520

0 input parameters with probes

Characteristic Description

Threshold Accuracy

Threshold range and step size

±100 mV

Settable from +4.5 V to -2 V in 5 mV steps

Threshold channel selection 16 threshold groups assigned to channels. P6410, P6417, P6418, and

P6419 probes have two threshold settings, one for the clock/qualiﬁer channel and one for the data channels. P6434 probes have four threshold settings, one for each of the clock/qualiﬁer channels and two for the data channels (one per 16 data channels).

Channel-to-channel skew

Channel-to-channel skew (Typical)

Sample uncertainty

≤ ±150 ps maximum

≤ ±75 ps

Asynchronous

Sample period

Synchronous

125 ps

Input voltage range –2.5 to +5 V

Probe input resistance (Typical) 20 kΩ

Probe in

(Typical)

put capacitance

P6410, P

P6418 1.4 pF data channels

6417, P6434

2pF

2pFCLK

/Qual channels

P6419 < 0.7 pF

Minimum slew rate (Typical) 0.2 V/ns

Maximum operating signal 6.0 V

Probe

overdrive

, P6417, P6418,

P6410 P6419

P6434

p-p

±250 mV or ±25% of signal swing minimum required beyond threshold, whichever is greater

±300 mV or ±25% of signal swing minimum required beyond threshold,

chever is greater

whi

±4 V maximum beyond threshold

imum nondestructive input signal to probe

Max

nimum input pulse width signal (single channel)

(Typical)

Delay time from probe tip to module input probe

±15

5 ns (P6434)

1.25 ns (P6410, P6417, P6418, P6419)

33 ns ±100ps

connector (Typical)

Table 3: TLA5200 timing latencies

Characteristic Description

System Trigger and External Signal Input Latencies

(Typical)

External System Trigger Input to LA Probe Tip

External Signal Input to LA Probe Tip via Signal 3, 4 –656 ns + Clk

External Signal Input to LA Probe Tip via Signal 1, 2

–656 ns

–656 ns + Clk

2 TLA5200 Series Product Speciﬁcations & Performance Veriﬁcation

+ 31 hidden pages

Tektronix TLA5201, TLA5202, TLA5203, TLA5204, TLA5201B Performance Verification

Specifications and Main Features

Frequently Asked Questions

User Manual