Tektronix TekExpress HEAC User manual

x
TekExpress
®
HEAC (HDMI Ethernet Audio Return Channel) Automated Solution
ZZZ
Quick Start User Manual
*P077038902*
xx
TekExpress
®
HEAC (HDMI Ethernet Audio Return Channel) Automated Solution
ZZZ
Quick Start User Manual
www.tektronix.com
Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or suppliers, and are protected by na
tional copyright laws and international treaty provisions.
Tektronix pro previously published material. S pecications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
TekExpress is a registered trademark of Tektronix, Inc.
ducts are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all
Contacting Tektronix
Tektronix, Inc. 14200 SW Karl Braun Drive P.O. Box 500 Beaverton, OR 97077 USA
For product information, sales, service, and technical support:
In North America, call 1-800-833-9200. Worldwide, visit www.tektronix.com to nd contacts in your area.
Warranty
Tektronix warrants that this product will be free from defects in materials and workmanship for a period of one (1) year from the date of shipment. If any such product proves defective during this warranty period, Tektronix, at its option, either will repair the defective product without charge for parts and labor, or will provide a replacement in exchange for the defective product. Parts, modules and replacement products used by Tektronix for warranty work may be new or reconditioned to like new performance. All replaced parts, modules and products become the property of Tektronix.
In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration of the warranty period and make suitable arrangements for the performance of service. Customer shall be responsible for packaging and shipping the defective product to the service center designated by Tektronix, with shipping charges prepaid. Tektronix shall pay for the return of the product to Customer if the shipment is to a location within the country in which the Tektronix service center is located. Customer shall be responsible for paying all shipping charges, duties, taxes, and any other charges for products returned to any other locations.
This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate maintenance and care. Tektronix shall not be obligated to furnish service under this warranty a) to repair damage resulting from a ttempts by personnel other than Tektronix representatives to install, repair or service the product; b) to repair damage resulting from improper use or connection to incompatible equipment; c) to repair any damage or malfunction caused by the use of non-Tektronix supplies; or d) to service a product that has been modied or integrated with other products when the effect of such modication or integration increases the time or difculty of servicing the product.
THIS WARRANTY IS GIVEN BY TEKTRONIX WITH RESPECT TO THE PRODUCT IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TEKTRONIX’ RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND E XCLU S IVE REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY. TEKTRONIX AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR THE VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.
[W2 – 15AUG04]
Table of Contents
General Safety Summary ... . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . . iii
Compliance I
Preface................................................................................................................................. vi
Install th
Use theTekExpress Software......................................................................................................... 3
Application Examples................................................................................................................. 10
ex
Ind
nformation ............................................................................................................... v
EnvironmentalConsiderations................................................................................................... v
Key Feature
Documentation.................................................................................................................. vii
Software Upgrades. . .. . .. . .. . .. . .. . .. . .. . .. . .. . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . . . .. . .. . .. . .. . .. . .. . .. . .. . .. vii
e Software .................................................................................................................... 1
Before Installation................................................................................................................ 1
Prerequisites . .. . .. . .. . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. ... 1
Installat
Required Test Equipment . . . . . . . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. .. . .. . .. . .. . .. . 2
Start the Software................................................................................................................2
Close the
Process Flow.....................................................................................................................3
Set Up th
Set Up the Jumpers on the HEAC-TPA-MAIN Fixture.......................................................................... 5
Select a Device, Test Suite, and Test ........................................................................................... 6
Congu
Connect and Congure the Equipment . . . . . . . . . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. 8
Run the Test......................................................................................................................8
Interp
Generate, Save, and Print a Report.. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . . 9
Diffe
Differential Mode Operating DC Voltage Test (Transmitter)................................................................... 14
Common Mode Transmitter Tests.............................................................................................. 18
Sing
Differential Receiver Tests ...................................................................................................... 29
Common Mode Receiver Tests................................................................................................. 33
Com
Single Mode Receiver Tests.................................................................................................... 43
Single Mode Operating DC Voltage Test (Receiver)........................................................................... 48
s ..................................................................................................................... vi
ion ........................................................................................................................ 1
Software............................................................................................................... 2
e Switches on the HEAC-TPA-MAIN Fixture ......................................................................... 4
re the Test Parameters .................................................................................................. 6
ret the Test Result ......................................................................................................... 9
rential Mode Transmitter Tests ............................................................................................ 10
le Mode Transmitter Tests ................................................................................................. 24
mon Mode Operating DC Voltage Test (Receiver) ....................................................................... 38
Table of Content
s
TekExpress HEAC Quick Start User Manual i
Table of Content
s
ii TekExpress HEAC Quick Start User Manual
General Safety S
ummary
General Safet
Review the following safety precautions to avoid injury and prevent damage to this product or any products connected to it.
To avoid potential hazards, use this product only as specied.
Only qualied personnel should perform service procedures.
While using this product, you may need to access other parts of a larger system. Read the safety sections of the other component manuals for warnings and cautions related to operating the system.
To Avoid Fire or Personal Injury
Use proper power cord. Use only the power cord specied for this product and certied for the country of use.
Use proper voltage setting. Before applying power, ensure that the line selector is in the proper position for the
source bei
Connect a
to a voltage source.
Ground the product. This product is indirectly grounded through the gr ounding conductor of the mainframe power cord.
To avoid electric shock, the grounding conductor must be c onnected to earth ground. Before making connections to the input or outpu
Observe
product manual for further ratings information before making connections to the product.
ng used.
nd disconnect properly.
t terminals of the product, ensure that the product is properly grounded.
all terminal ratings.
y Summary
Do not connect or disconnect probes or test leads while they are connected
To avoid re or shock hazard, observe all ratings and markings on the product. Consult the
The inputs are not rated for connection to mains or Category II, III, or IV circuits.
Do not apply a potential to any terminal, including the common terminal, that exceeds the maximum rating of that terminal.
Power disconnect. The power cord disconnects the product from the power source. Do not block the power cord; it
must remain accessible to the user at all times.
Do not operate without covers. Do not operate this product with covers or panels removed.
Do not operate with suspected failures. If you suspect that there is damage to this product, have it inspected by
ed service personnel.
quali
exposed circuitry.
Avoid
roper AC adapter.
Use p
Do not touch exposed connections and components when power is present.
Use only the AC adapter specied for this product.
Do not operate in wet/damp conditions.
Do not operate in an explosive atmosphere.
Keep product surfaces clean and dry.
TekExpress HEAC Quick Start User Manual iii
General Safety S
Terms in This Manual
These terms may appear in this manual:
WARNING. Warning statements identify conditions or practices that could result in injury or loss of life.
CAUTION. Caution statements identify conditions or practices that could result in damage to this product or other property.
Symbols and Terms on the Product
These terms may appear on the product:
DANGER indicates an injury hazard immediately accessible as you read the marking.
WARNING indicates an injury hazard not immediately accessible as you read the marking.
CAUTION indicates a hazard to property including the product.
The following symbol(s) may appear on the product:
ummary
iv TekExpress HEAC Quick Start User Manual
Compliance Info
rmation
Compliance In
This section lists the environmental standards with which the instrument complies.
formation
Environmental Considerations
This section provides information about the environmental impact of the product.
Product End-of-Life Handling
Observe the following guidelines when recycling an instrument or component:
Equipment
equipment may contain substances that could be harmful to the environment or human health if improperly handled at the product’s end of life. In order to avoid release of such substances into the environment and to reduce the use of natural resource reused or recycled appropriately.
Recycling.
s, we encourage you to recycle this product in an appropriate system that will ensure that most of the materials are
This symb to Directives 2002/96/EC and 2006/66/EC on waste electrical and electronic equipment (WEEE) and batteries. For information about recycling options, check the Support/Service section of the Tektronix Web site (ww
Production of this equipment required the extraction and use of natural resources. The
ol indicates that this product complies with the applicable European Union requirements according
w.tektronix.com).
Restriction of Hazardous Substances
This product has been classied as Monitoring and Control equipment, and is outside the scope of the 2002/95/EC RoHS Directive.
TekExpress HEAC Quick Start User Manual v
Preface
Preface
TekExpress is the Tektronix Compliance Test Automation Framework, developed to support current and future test automation needs of customers. Developed using National Instruments’ TestStand, TekExpress leverages on the capabilities of the Microsoft .NE T framework. TekExpress HEAC provides a test and compliance solution that address the needs of the of HDMI 1.4 and CTS 1.4 standards.
Key Features
The application provides the following features:
Reliable testing
Conformance to HDMI 1.4 (HEAC) standards and test specications CTS 1.4 ensures reliable results
Accurate Transmitter (Tx) and Receiver (Rx) testing and violation testing ensures reliable tests
Sophisticated measurement techniques eliminate errors in jitter measurements
Closed loop measurements eliminate non-linearities of test setup enables precise testing
Signicantly reduced test times for Sink and Audio tests
Optimal setups ensure accurate results
Fast testing
Remote control of signal sources automates Source and Sink tests and reduces test times
One-button selection of multiple tests ensures faster testing
Automatic mask t, measurements, and Pass/Fail notication delivers quick results
Test margins and statistical information aid analysis to help nd answers quickly
One-button CSV-format summary and MHT report saves time
Complete testing
Wide range of tests for Source and Sink devices enables complete validation
Complete compliance solution with a test xture and signal sources
vi TekExpress HEAC Quick Start User Manual
Documentation
This manual describes the basic installation and operation of the TekExpress application. For more detailed information, see the online help. The following information is available for this product:
Table i: Related documentation
Preface
TekExpress HEAC Online Help, English
TekExpress
TekExpress HEAC Quick Start User Manual, English (PDF)
HEAC User Manual, English (PDF)
Software Upgrades
Periodic software upgrades may become available. To check for upgrades:
Go to the Tektronix Web site (www.tektronix.com/software).
Enter the product name (TekExpress HEAC).
076-0191-xx
077-0388-xx
077-0389-x
x
TekExpress HEAC Quick Start User Manual vii
Preface
viii TekExpress HEAC Quick Start User Manual
Install the Soft
ware
Install the So
The TekExpress application must be installe d on a computer or on a Tektronix oscilloscope.
ftware
Before Installation
Read the Readme.txt le provided with the product software.
Prerequisites
The product software installer automatically installs all the necessary software and components needed to run the TekExpress HEAC solution. The following are the prerequisites:
Microsoft .NET Framework
National Instruments TestStand Runtime Engine
OpenChoice TekVISA
DK2 DESKey Driver
TekExpress Framework
Installation
1. Close a
2. Downlo
3. Double
in
C:\Program Files \Tektronix\TekExpress\TekExpr ess HEAC.
4. Download the executables:
terns_AWG7K.EXE
5. Double-click the executables to extract the les. The audio patterns are extracted to
ll applications.
ad
HEACWebinstaller_<version>.EXE.
-click the executable to extract the les. After extraction, the HEAC installer launches and the software is installed
HEAC_AudioRX_Patterns_AWG5K.EXE and HEAC_AudioRX_Pat-
.
C:\HEAC Pattern s.
TekExpress HEAC Quick Start User Manual 1
Install the Soft
ware
Required Test Equipment
Each test suite requires specic equipment setups. Click Show Schematic within the select pane to see how to connect the device under test and test equipment to your oscilloscope.
The following Tektronix test xtures are required, depending on the tests that you will be running:
TF-HEAC-TPA-KIT consisting of:
TF-HEAC-TPA-MAIN
TF-HEAC-TPA-AP
TF-HEAC-TPA-CP
TF-HEAC-TDR-AR (2 numbers)
TF-HEAC-TDR-CR (2 numbers)
TF-HDMI-TPA-CE (EDID board) consisting of:
EDID xture PCBA
EEPROM with HDMI 1.4 software
Ribbon cable
TF-HDMID-TPA-KIT (required for HEAC testing of Type D devices) consisting of:
Plug assembly
Receptacle cable assembly (2 numbers)
The following arbitrary waveform generators are required for running common mode receiver tests:
Tektronix AWG5000 Series or AWG5000B Series
Tektronix AWG7000 Series or AWG7000B Series
Start the Software
To start the software, do one of the following:
From the Start menu, select Start > Programs > Tektronix > TekExpress > TekExpress HEAC.
Double-click on the desktop.
Close the Software
lose the software, do one of the following:
To c
ect File > Exit.
Sel
Click .
2 TekExpress HEAC Quick Start User Manual
Use the TekExpre
ss Software
Use the TekExp
Process Flow
Follow steps 1 through 11 to select and run a test to check for compliance. Details for each of these actions are given on the following pages.
1. Set up the switches on the HEAC-TPA-MAIN xture.
2. Set up the jumpers on the HEAC-TPA-MAIN xture.
3. Select a device.
4. Select the test suite and choose the version.
5. Select the test.
6. Congure the test parameters.
7. View and select connected instruments.
8. Run the test.
9. View the progress of acquisition.
10. View the progress of analysis.
11. View and print the generated report.
ress Software
TekExpress HEAC Quick Start User Manual 3
Use the TekExpre
ss Software
Set Up the Switches on the HEAC-TPA-MAIN Fixture
The following diagram shows the xture conguration switches on the HEAC-TPA-MAIN xture.
The following table shows the settings to congure on the HEAC-TPA-MAIN xture.
Table 1: HEAC-TPA-MAIN switch setup
+5 V
Test ID Description DUT
Source
Sink
Source
Sink
Sink
Sink
Source
Sink
Source
5-2to5-5
5-6 to 5-10
5-11 to 5-15
5-16
5-17
Differential Mode Operating DC
Differential Mode Transmitter
Common Mode Transmitter
Single Mode Transmitter
Differential Mode Receiver
Common Mode Receiver
from S1 S2 S3 S4 S7
J6, J8 Right Right Right
J8
J6 Right Right Right Right Right
J8
J8
J8
J6 Right Right Right Right Right
J8
J6 Right Right Right Right Right
Left Left Left
Left Left Left
Left Left Left
Left Left Left
Left Left Left
Left
Right
Right
Right
Right
Right
Right5-1
Left
Left
Left
Left
Left
4 TekExpress HEAC Quick Start User Manual
Table 1: HEAC-TPA-MAIN switch setup (cont.)
+5 V
Test ID Description DUT
5-18
5-19
5-20
Single Mode Receiver
Common Mode Operating DC
Single Mode Operating DC
Source
Source
Source
from S1 S2 S3 S4 S7
J6, J8 Right Right Right
J6, J8 Right Right Right
J6, J8 Right Right Right
Set Up the Jumpers on the HEAC-TPA-MAIN Fixture
owing table shows the jumper settings to congure on the HEAC-TPA-MAIN xture.
The foll
Table 2: HEAC-TPA-MAIN jumper setup
Use the TekExpre
Left
Left
Left
ss Software
Right
Right
Right
Test ID Description
5-1to5-5
5-6 to 5-10
to 5-15
5-11
5-16
5-17 to 5-19
5-18 to 5-20
Differential Mode
mitter
Trans
n Mode
Commo Transmitter
Single Mode Transmitter
Differential Mode
eiver
Rec
Common Mode
eceiver
R
ingle Mode
S Receiver
Termi­nation
50
50
55
-
-
-
5
ource
ON OFF ON OFF
ON OFF ON OFF
OFF OFF OFF OFF
FF
O
FF
O
FF
O
FF
O
Signal S output impedance JP1 JP2 JP3 JP4
-
-
-
110 OFF OFF OFF OFF
100 ON OFF ON OFF
90 ON ON ON ON
50 ON OFF ON OFF
5
TekExpress HEAC Quick Start User Manual 5
Use the TekExpre
ss Software
Select a Device, Test Suite, and Test
1. Click the Sele
2. Select a Devic
3. Select the Te
4. Choose the ve suite from the Version drop-down list.
5. Select the test to run. You can select
multiple tests from the list.
6. Click Select All to select all the tests in the list.
7. Click Dese
8. Click Sho
schematic diagram of the test setup.
ct tab.
e type.
st Suite.
rsion of the selected test
lect All to disable the tests.
w Schematic to see the
Congure the Test Parameters
1. Click th
e test name to congure.
2. Click C
3. If multiple instruments are connected,
4. Verify schematic-related parameters
5. The Compliance Mode is selected by
ongure.
choose the correct instrument from the drop-down list in the parameter-value list.
such as DUT HEAC Signal connected to Real Time Scope at and others. You can also change other parameters such as Minimum signal threshold.
default. You can generally use the default settings in Compliance Mode.
6 TekExpress HEAC Quick Start User Manual
6. Click the Acquire tab to view parameters
related to acquisition.
7. Click the Analyze tab to view the test
analysis parameters.
Use the TekExpre
ss Software
8. Click th
9. Click t
10. Click Apply.
11. Click Close.
NOTE
session.
e Limits tab to view the
measurement limits.
See the online help for various test limit
sons.
compari
he Comments tab to enter
test-specic comments.
. Use the File menu to save the
TekExpress HEAC Quick Start User Manual 7
Use the TekExpre
ss Software
Connect and Congure the Equipment
The equipment connection is given in detail in the Application Examples section of this document. (See page 10, Application Examples.)
You can cli ck Show Schematic to display a diagram of the test setup for each of the test suites.
Run the Test
1. EntertheIDoftheDevicetobetested in the DUT ID eld.
2. Click Run to run the test.
3. Click the Acquire tab to view the
waveform acquisition details for the tests in the currently selected test suite.
4. Click the Analyze tab when the tests are running to view the status and progress of the tests. The application checks to see if the device has passed the test.
The Status Messages window time stamps all runtime messages and displays them.
8 TekExpress HEAC Quick Start User Manual
Interpret the Test Result
When the test completes, the report summary appears. Check the report to see if the device passed the test.
1. The report displays the DUT ID, the date
and time the test was run, and execution time.
2. Test information like the Device Type,
Version, Execution Time, Compliance Mode (Yes or No), and Overall Test Result (Pass or Fail), MAC Address (in case of Receiver tests) are shown.
3. Instrument information like the models,
serial numbers, and rmware/software versions are shown.
4. A table displays the Test Name,
Measurement Details, Limit1 and Limit2, CRC Status, CRC Details, Test Result, Compliance Mode, Analysis Time, and Comments.
Use the TekExpre
ss Software
Generate, Save, and Print a Report
ou have successfully run one or more test(s), a report summary is generated in MHT format.
After y
To save
To prev
the report summary in the desired location, select File > Save Report As.
iew the report before printing, select File > Print Preview Report. Select File > Print Report.
TekExpress HEAC Quick Start User Manual 9
Application Exa
mples
Application Examples
Differential Mode Transmitter Tests
Required equipment Model supported
Real-time os
Probe
Test xture TF-HEAC-TPA-P (A/C) or TF-HEAC-TPA-KIT,
50 SMA T
cilloscope
erminators
Tektronix DPO7000 Series, DPO70000 Series, DPO70000B Series, DSA 70000 Series, DSA70000B Series, and MSO70000 Ser
Tektronix P DPO70000 Series, DPO70000B Series, DSA70000 Series, DPO70000B, and MSO70000 Series Digital and Mixed Signal Osc
Tektronix P6330, TDP1000, TDP 1500,, or TDP3500 for a Tektronix DPO7000 Series Digital Oscilloscope
TF-HDMID
Any term
ies Digital and Mixed Signal Oscilloscopes
6247, P6248, P6330, or P7330 for a
illoscope
-TPA-KIT
inator that meets the following requirements:
50 impe
Connect
DUT
SMA Cab
HDMI Cable HDMI cable with HEAC capability
This tests the DUT for compliance with differential mode transmitter tests.
les
An HEAC
nix part number 174-1428-00 (1.5 meter)
Tektr o
Tektronix part number 174-1341-00 (1 meter)
dance ± 1% or better
s directly to the SMA female connector
sink or source device
10 TekExpress HEAC Quick Start User Manual
Application Exa
1. Connect the DUT to the equipment as shown.
NOTE. This equipment setup diagram and connections are the same for all differential transmitter tests except the
Operating DC V
oltage test.
mples
Connect the CEC or CDC Controller to the CEC/CDC Control Port on the HEAC-TPA main board.
Connect the HEAC-TPA plug board to the HEAC connector on the Source/S ink DUT.
Connect the 50 SMA terminators to the HEAC-TPA main board.
Connect a differential probe to the HEAC± differential signal probe point on the HEAC-TPA main board.
If you are testing a Sink DUT, set the HEAC-TPA main board to enable the Sink DUT test. Set switch S7 position to the left (Off position) on the HEAC-TPA adapter.
If you are testing a Source DUT, set the H EAC-TPA main board to enable the Source DUT test. Activate +4 V bias using the +5 V power from the Source DUT. Set switch S7 to the right (On position) on the HEAC-TPA main xture.
Activate the HEC transmission on the HEAC Source/Sink DUT using CEC/CDC controller.
TekExpress HEAC Quick Start User Manual 11
Application Exa
2. Select HEAC-Transmitter as the device
mples
type.
By default, th as the Test Suite.
The default version CTS 1.4.
All the diffe except the Template test, are selected by default.
e Differential-Tx is selected
rential mode transmitter tests,
NOTE. The Te
test and not a part of the CTS 1.4.
3. Enter the D ID eld.
4. Click Show Schematic to display a
diagram of the test setup and conrm that your
5. Click Co Conguration panel.
6. Use the default values in the Compliance Mode to run the tests for compliance with the st
NOTE. To change acquisition parameter
values, click User Dened Mode.A
ge appears prompting you that if you
messa make changes to a test, the test may no longer be compliant. Click OK to proceed
the User Dened Mode.
with
7. Click Close.
mplate test is an informative
UT identication in the DUT
test setup is correct.
ngure to open the
andards.
8. Click Run in the Select panel.
12 TekExpress HEAC Quick Start User Manual
9. Click the Analyze tab to view test
analysis results.
10. The application displays the status of the
tests in the St
atus Messages window.
Click Save Status to save the status messages.
11. When the tests complete, the application
shows a report in the Report panel.
Application Exa
mples
TekExpress HEAC Quick Start User Manual 13
Application Exa
mples
Differential Mode Operating DC Voltage Test (Transmitter)
Required equipment Model supported
Real-time osc
Probe
Test xture TF-HEAC-TPA-P (A/C) or TF-HEAC-TPA-KIT,
50 SMA Te
illoscope
rminators
Tektronix DPO7000 Series, DPO70000 Series, DPO70000B Series, DSA 70000 Series, DSA70000B Series, and MSO70000 Ser
Tektronix P6 DPO70000 Series, DPO70000B Series, DSA70000 Series, DPO70000B, and MSO70000 Series Digital and Mixed Signal Osci
Tektronix P6330, TDP1000, TDP1500, or TDP3500 for a Tektronix DPO7000 Series Digital Oscilloscope
TF-HDMID-
Any termi
ies Digital and Mixed Signal Oscilloscopes
247, P6248, P6330, or P7330 for a
lloscope
TPA-KIT
nator that meets the following requirements:
50 imped
Connect
DUT
SMA Cab
HDMI Cable HDMI cable with HEAC capability
This tests the DUT for compliance with d ifferential mode operating DC voltage (Transmitter) tests.
les
An HEAC s
nix part number 174-1428-00 (1.5 meter)
Tektr o
Tektronix part number 174-1341-00 (1 meter)
ance ± 1% or better
s directly to the SMA female connector
ink or source device
14 TekExpress HEAC Quick Start User Manual
1. Connect the equipment as shown.
Application Exa
mples
NOTE. Use two probes for DC voltage measurement. Use the differential mode conguration for other measurements.
Connect the CEC or CDC Controller to the CEC/CDC Control Port of the HEAC-TPA main board.
Connect the HEAC-TPA plug board to the HEAC connector of the Source/Sink DUT.
Connect the 50 SMA terminators to the HEAC-TPA main board.
Connect the rst single-ended probe from Ch1 of the digital oscilloscope to the HEAC+ probe point on the HEAC-TPA main board, and the second single-ended probe from Ch2 to the HEAC- probe point.
If you are testing a Sink DUT, set the HEAC-TPA main board to enable the Sink DUT test. Set switch S7 to the left (Off position) on the HEAC-TPA main xture.
If you are testing a Source DUT, set the HEAC-TPA main board to enable the Source DUT test, and use +5 V power from the DC Power Supply. Set switch S7 to the right (On position) and the switch S4 is set to the left (Off position) on the HEAC-TPA main xture.
NOTE. Do not use +5 V power from the Source DUT.
Connect and congure the DC Power Supply to s upply +5 V to the HEAC-TPA m ain board.
Power on the Source/Sink DUT.
Activate the HEC transmission capability for the HEAC Source/Sink DUT using the CEC/CDC controller.
TekExpress HEAC Quick Start User Manual 15
Application Exa
2. Select HEAC-Transmitter as the device
mples
type.
By default, Di the Test Suite.
The default version CTS 1.4.
fferential-Tx is selected as
3. Click Des Operating DC Voltage test.
4. Enter the DUT identication in the DUT ID eld.
5. Click Show Schematic to display a
diagra that your test setup is correct.
6. Click Congure to open the Conguration panel.
7. Use the default values in the Compliance Mode the standards.
NOTE. To change acquisition parameter
es, click User Dened Mode.A
valu message appears prompting you that If you make changes to a test, the test may no
ger be compliant. Click OK to proceed
lon with the User Dened Mode.
8. Click Close.
elect All and select only the
m of the test setup and conrm
to run the tests for compliance with
16 TekExpress HEAC Quick Start User Manual
9. Click Run in the Select panel.
The application switches to the Acquire tab.
10. Follow the on-screen prompts and the
schematics to change the setup. Click
OK to continue.
11. Click the Analyze tab to view test
analysis results.
12. The application displays the status of the
tests in the Status Messages window. Click Save Status to save the status messages.
Application Exa
mples
13. When the tests complete, the application
shows a report in the Report panel.
TekExpress HEAC Quick Start User Manual 17
Application Exa
mples
Common Mode Transmitter Tests
Required equipment Model supported
Real-time osc
Probe
illoscope
Tektronix DPO7000 Series, DPO70000 Series, DPO70000B Series, DSA 70000 Series, DSA70000B Series, and MSO70000 Ser
Tektronix P6 Series, DPO70000B Series, DSA70000 Series, and DSA70000B Series, and MSO7000 Series Digital and Mixed Oscil
Tektronix P6243, P6245, or TAP1500 for Tektronix DPO7000 Series Digital Oscilloscopes
ies Digital and Mixed Signal Oscilloscopes
243 or P6245 for Tektronix DPO70000
loscopes
NOTE. Yo u c
single-ended mode.
Test xture TF-HEAC-TPA-P (A/C) or TF-HEAC-TPA-KIT,
TF-HDMID-TPA-KIT
50 SMA Terminators Any terminator that meets the following requirements:
DUT
SMA Cables Tektronix part number 174-1428-00 (1.5 meter)
able
HDMI C
An HEAC sink device
onix part number 174-1341-00 (1 meter)
Tektr
HDMI c
an also use two differential probes in
50 impedance ± 1% or better
Connects directly to the SMA female connector
able with HEAC capability
18 TekExpress HEAC Quick Start User Manual
This tests the DUT for compliance with common mode (Transmitter) tests.
Application Exa
mples
1. Connect the eq
uipment as shown.
Connect the CEC or CDC Controller to the CEC/CDC Control Port of the HEAC-TPA main board.
Connect the HEAC-TPA plug board to the HEAC connector of the Sink DUT.
Connect the 50 terminators to the HEAC-TPA main /board.
Connect the rst single-ended probe from Ch1 of the digital oscilloscope to the HEAC+ probe point on the HEAC-TPA main board, and the second single-ended probe from Ch2 to the HEAC– probe point.
Set the HEAC-TPA main board to enable the Sink DUT test.
Connect and congure DC Power Supply to drive +5 V to the HEAC-TPA main board.
Power on the Sink DUT.
Activate the ARC (Common mode) transmission on the HEAC Sink DUT using the CEC/CDC controller.
TekExpress HEAC Quick Start User Manual 19
Application Exa
2. Select HEAC-Transmitter as the device
3. Select CommonMode-Tx.
4. Enter the DUT identication in the DUT
mples
type.
The default v
All the common mode transmitter tests are selected by default.
ID field.
ersion CTS 1.4.
5. Click Show diagram of the test setup and conrm that your test setup is correct.
6. Click Congure to open the Congur
7. Use the d Mode to run the tests for compliance with the standards.
NOTE. T
values, click User Dened Mode.A message appears prompting you that If you
hanges to a test, the test may no
make c longer be compliant. Click OK to proceed with the User Dened Mode.
k Close.
8. Clic
Schematic to display a
ation panel.
efault v alues in the Compliance
o change acquisition parameter
9. Click Run in the Select panel.
The application switches to the Acquire tab.
20 TekExpress HEAC Quick Start User Manual
10. Click the Analyze tab to view test
analysis results.
11. The application displays the status of the
tests in the St
atus Messages window.
Click Save Status to save the status messages.
12. Follow the on-screen prompts. For the
Rise-Fall Time test, congure the DUT to transmit an MLT-3 signal and click OK.
Application Exa
mples
13. When prompted, congure the DUT to
disable the MLT-3 signal and click OK.
TekExpress HEAC Quick Start User Manual 21
Application Exa
mples
14. The Transmit Ji
tter MAX test is run at three frequencies. The application prompts you to congure the DUT for each of these f
requencies: 4.096 MHz,
5.688 MHz, and 6.144 MHz. If your device supports the frequency, congure the DUT, and c
lick OK.
22 TekExpress HEAC Quick Start User Manual
15. The IEC Stream Verication test is run
under three conditions: With +5 V power turned on and A
RC activated, With +5 V power turned off, and With +5 V power turned on and ARC not activated. Follow the prompts a
nd click OK.
Application Exa
mples
16. When the
tests complete, the application
shows a report in the Report panel.
TekExpress HEAC Quick Start User Manual 23
Application Exa
mples
Single Mode Transmitter Tests
Required equipment Model supported
Real-time osc
Probe
illoscope
Tektronix DPO7000 Series, DPO70000 Series, DPO70000B Series, DSA 70000 Series, DSA70000B Series, and MSO70000 Ser
Tektronix P6 Series, DPO70000B Series, DSA70000 Series, and DSA70000B Series, and MSO7000 Series Digital and Mixed Oscil
Tektronix P6243, P6245, or TAP1500 for Tektronix DPO7000 Series Digital Oscilloscopes
ies Digital and Mixed Signal Oscilloscopes
243 or P6245 for Tektronix DPO70000
loscopes
NOTE. Yo u c
single-ended mode.
Test xture TF-HEAC-TPA-P (A/C) or TF-HEAC-TPA-KIT,
TF-HDMID-TPA-KIT
50 SMA Terminators Any terminator that meets the following requirements:
DUT
SMA Cables Tektronix part number 174-1428-00 (1.5 meter)
able
HDMI C
An HEAC sink device
onix part number 174-1341-00 (1 meter)
Tektr
HDMI c
an also use two differential probes in
50 impedance ± 1% or better
Connects directly to the SMA female connector
able with HEAC capability
24 TekExpress HEAC Quick Start User Manual
This tests the DUT for compliance with single mode (Transmitter) tests.
1. Connect the equipment as shown.
Application Exa
mples
Connect the CEC or CDC Controller to the CEC/CDC Control Port on the HEAC-TPA main board.
Connect the HEAC-TPA plug board to the HEAC connector on the Sink DUT.
Connect the 50 SMA terminators to the HEAC-TPA main board.
Set the Impedance Conversion Circuit on the HEAC-TPA main board to 55 Ω.
Connect a single-ended probe from Ch1 of the digital oscilloscope to the HEAC+ probe point on the HEAC-TPA main board.
Set the HEAC-TPA main board to enable the Sink DUT test.
Connect and set the DC Power Supply to supply +5 V to the HEAC-TPA main board. Set switch S7 to the left (Off position) on the HEAC-TPA m ain xture.
Power on the Sink DUT.
Activate the ARC (Single mode) transmission on the HEAC Sink D UT using the CEC/CDC c ontroller.
TekExpress HEAC Quick Start User Manual 25
Application Exa
2. Select HEAC-Transmitter as the device
3. Select SingleMode-Tx.
4. Enter the DUT identication in the DUT
mples
type.
The default v
All the single mode transmitter tests are selected by default.
ID field.
ersion CTS 1.4.
5. Click Show
diagram of the test setup and conrm that your test setup is correct.
6. Click Congure to open the
Conguration panel.
7. Use the default values in the Compliance
Mode to r the standards.
NOTE. To change acquisition parameter
,clickUser Dened Mode.A
values message appears prompting you that If you make changes to a test, the test may no
be compliant. Click OK to proceed
longer with the User Dened Mode.
8. Click Close.
Schematic to display a
un the tests for compliance with
9. Click Run in the Select tab.
The application switches to the Acquire tab.
26 TekExpress HEAC Quick Start User Manual
10. Click the Analyze tab to view test
analysis results.
11. The application displays the status of the
tests in the S
tatus Messages window.
Click Save Status to save the status messages.
12. The Transmit Jitter MAX test is run
at three frequencies. The application prompts you to congure the DUT for each of these frequencies: 4.096 MHz,
5.688 MHz, and 6.144 MHz. If your device supports the frequency, congure the DUT, and click OK.
Application Exa
mples
TekExpress HEAC Quick Start User Manual 27
Application Exa
13. The IEC Stream Verication test is run
mples
under three conditions: with +5 V power turned on and A
RC activated, with +5 V power turned off, and with +5 V power turned on and ARC not activated. Follow the prompts a
nd click OK.
14. When the tests complete, the application
shows a report in the Report panel.
28 TekExpress HEAC Quick Start User Manual
Differential Receiver Tests
Required equipment Model supported
Real-time osc
Arbitrary wa
Probe
Test xtu
DUT
SMA Cables Tektronix part number 174-1428-00 (1.5 meter)
HDMI Cable HDMI cable with H EAC capability
illoscope
veform generator
re
Application Exa
Tektronix DPO7000 Series, DPO70000 Series, DPO70000B Series, DSA70000 Series, DSA70000B Series, and MSO70000 Ser
Tektronix AW or AWG7000B Series Arbitrary Waveform Generator
Tektronix P6247, P6248, P6330, or P7330 for a DPO70000 Series, DPO70000B Series, DSA70000 Series, DPO70000B Signal Oscilloscope
Tektronix P6330, TDP1000, TDP1500, or TDP3500 for a Tektronix
TF-HEAC­TF-HDMID-TPA-KIT
An HEAC sink or source device
Tektronix part number 174-1341-00 (1 meter)
ies Digital and Mixed Signal Oscilloscopes
G5000 Series, AWG5000B, AWG7000 Series,
, and MSO70000 Series Digital and Mixed
DPO7000 Series Digital Oscilloscope
TPA-P (A/C) or TF-HEAC-TPA-KIT,
mples
ests the DUT for compliance with differential receiver tests.
This t
TekExpress HEAC Quick Start User Manual 29
Application Exa
1. Connect the DUT to the equipment as shown.
mples
Connect a LAN cross-cable from the digital oscilloscope to the waveform generator, and enable the TekVISA connection
waveform generator and to the digital oscilloscope.
to the
ct an SMA cable to the Ch1 Marker1 output and to Ch2 on the digital oscilloscope.
Conne
ct the HEAC-TPA plug board to the HEAC connector of the Source/Sink DUT.
Conne
ect the Ch1 Analog(+) output of the arbitrary waveform generator to the HEAC+ SMA connector on the HEAC-TPA
Conn main board and the Ch2 Analog(+) to HEAC–.
Set the Impedance Conversion Circuit on the HEAC-TPA main board to 50 Ω.
Connect a differential probe to the HEAC± differential signal probe point on the HEAC-TPA main board.
Connect the CEC or CDC Controller to the CEC/CDC Control Port of the HEA C-TPA main board.
If you are testing a Sink DUT, set the HEAC-TPA main board to enable the Sink DUT test. Set switch S7 to the left (Off position) on the HEAC-TPA main board.
ou are testing a Source DUT, set the HEAC-TPA main board to enable the Source DUT test. Activate +4 V bias by
If y using the +5 V power from the Source DUT. Set switch S7 to the right (On position) on the HEAC-TPA main xture.
Activate the HEC transmission on the HEAC Source/Sink DUT using the CEC/CDC controller.
30 TekExpress HEAC Quick Start User Manual
2. Select HEAC-Receiver as the device
type.
3. Select the Differential-Rx as the Test
Suite.
The default version CTS 1.4.
All the differential mode receiver tests are selecte
4. Enter the DUT IP Address.
5. Enter the DUT identication in the DUT
ID eld.
d by default.
Application Exa
mples
6. Click Sho
diagram of the test setup and conrm that your test setup is correct.
7. Click Congure to open the
Congur
8. Use the
Mode to run the tests for compliance with the standards.
NOTE.
available for HEAC Differential Receiver tests.
9. Clic
w Schematic to display a
ation panel.
default v alues in the Compliance
The User Dened Mode is not
k Close.
10. Click Run in the Select panel to run the
test.
TekExpress HEAC Quick Start User Manual 31
Application Exa
11. Click the Acquire tab to view the
12. The application displays the status of the
13. When the tests complete, the application
mples
acquisition details.
tests in the S
tatus Messages window.
Click Save Status to save the status messages.
shows a report in the Report panel.
32 TekExpress HEAC Quick Start User Manual
Common Mode Receiver Tests
Required equipment Model supported
Real-time Oscilloscope Tektronix DPO7000 Series, DPO70000 Series, DPO70000B
Arbitrary wa
HEAC TPA-P adapter Tektronix HEAC-TPA-P
Test xture T F-HEAC-TPA-P (A/C) or TF-HEAC-T PA-KIT,
DUT
SMA Cables Tektronix part number 174-1428-00 (1.5 meter)
HDMI Cab
This tests the DUT for common mode receiver tests.
1. Connect the DUT to the equipment as shown.
veform generator
le
Application Exa
Series, DSA70000 Series, DSA70000B Series, and MSO70000 Ser
Tektronix AW or AWG7000B Series Arbitrary Waveform Generator
TF-HDMID-TPA-KIT
An HEAC source device
Tektro n
HDMI cab
ies Digital and Mixed Signal Oscilloscopes
G5000 Series, AWG5000B Series, AWG7000,
ix part number 174-1341-00 (1 meter)
le with HEAC capability
mples
NOTE. T
Operating DC Voltage Test.
his equipment setup diagram and connections are the same for all common mode receiver tests except the
TekExpress HEAC Quick Start User Manual 33
Application Exa
mples
Connect the HEAC-TPA main board to the HEAC connector on the Source DUT.
Connect the CEC or CDC Controller to the CEC/CDC Control Port of the HEA C-TPA main board.
Connect the Ch1 Analog(+) output from a waveform generator to the HEAC+ SMA connector of the HEAC-TPA main board, and the C h2 Analog(+) to the HEAC– SMA connector.
Set the Impedance Conversion Circuit on the HEAC-TPA main board to 50 Ω.
Set the HEAC-TPA main board to enable the Source DUT test.
Activate +4 V bias using the +5 V power from the Source DUT.
Activate ARC (Common mode) transmission capability for the HEAC Source DUT using the CEC/CDC controller.
34 TekExpress HEAC Quick Start User Manual
2. Select HEAC-Receiver as the device
type.
3. Select CommonMode-Rx as the Test
Suite.
All the common mode receiver tests are selected by default.
The default
version CTS 1.4.
Application Exa
mples
4. Enter the DU
ID eld.
5. Click Show Schematic to display a
diagram of the test setup and conrm that your
6. Click Co
Conguration panel.
7. Use the default values in the C ompliance
Mode to run the tests for compliance with the sta
NOTE. The User Dened Mode is not
available for HEAC Common Mode Receiver
.
tests
T identication in the DUT
test setup is correct.
ngure to open the
ndards.
ck Close.
8. Cli
ick Run in the Select panel to run the
9. Cl
test.
The application switches to the Acquire
b.
ta
TekExpress HEAC Quick Start User Manual 35
Application Exa
10. Click the Analyze tab.
11. The application displays the status of the
mples
tests in the Status Messages window. Click Save Sta
tus.
36 TekExpress HEAC Quick Start User Manual
Application Exa
mples
12. As the selected
tests are executed, the application prompts you to verify the audio response from the DUT. Click Detecte
d or Not Detected as
appropriate for each test.
13. Follow the on-screen prompts and the
schematics to change the setup. Click
OK to continue.
14. When the tests complete, the application
shows a report in the Report panel.
TekExpress HEAC Quick Start User Manual 37
Application Exa
mples
Common Mode Operating DC Voltage Test (Receiver)
Required equipment Model supported
Real-time osc
Arbitrary wa
Probe
HEAC TPA-
Test xt
DUT
SMA Cables Tektronix part number 174-1428-00 (1.5 meter)
HDMI Cable HDMI cable with HEAC capability
illoscope
veform generator
P adapter
ure
Tektronix DPO7000 Series, DPO70000 Series, DPO70000B Series, DSA 70000 Series, DSA70000B Series, and MSO70000 Ser
Tektronix AW and AWG7000B Series Arbitrary Waveform Generator
Tektronix P6243 or P6245 for Tektronix DPO70000 Series, DPO70000B Series, DSA70000 Series, and DSA70000B Mixed Oscilloscopes
Tektronix P6243, P6245, or TAP1500 for Tektronix DPO7000 Se
Tektroni
TF-HEAC TF-HDMID-TPA-KIT
An HEAC source device
Tektronix part number 174-1341-00 (1 meter)
G5000 Series, AWG5000B, AWG7000 Series,
Series, and MSO7000 Series Digital and
ries Digital Oscilloscopes
x HEAC-TPA-P
-TPA-P (A/C ) or TF-HEAC-TPA-KIT,
ies Digital and Mixed Signal Oscilloscopes
ests the DUT for compliance with common mode operating DC voltage (Receiver) tests.
This t
38 TekExpress HEAC Quick Start User Manual
1. Connect the DUT to the equipment as shown.
Application Exa
mples
Connect the HEAC-TPA plug board to the HEAC connector on the Source DUT.
Connect the CEC or CDC Controller to the CEC/CDC Control Port on the HEAC-TPA main board.
Connect the Ch1 Analog(+) output from a waveform generator to the HEAC+ SMA connector of the HEAC-TPA main board, and the C h2 Analog(+) to the HEAC– SMA connector.
Set the Impedance Conversion Circuit on the HEAC-TPA main board to 50 Ω.
Connect a single-ended probe from Ch1 of the Digital Oscilloscope to the HEAC+ probe point on the HEAC-TPA main
rd, and a second single-ended probe from Ch2 to the HEAC- probe point.
boa
the HEAC-TPA main board to enable the Source DUT test, and to use +5 V power from the DC Power Supply. Set
Set switch S7 to the right (On position) on the HEAC-TPA main xture.
NOTE. Do not use +5 V power from the Source DUT.
Connect and set the DC Power Supply to supply +5 V to the HEAC-TPA main board.
Power on the Source DUT.
Activate the ARC (Common mode) transmission on the HEAC Source DUT using the CEC/CDC controller.
TekExpress HEAC Quick Start User Manual 39
Application Exa
2. Select HEAC-Receiver as the device
3. Select the CommonMode-Rx as the
4. Click Deselect All and select the
5. Enter the DUT identication in the DUT
mples
type.
Test Suite.
The default version CTS 1.4.
Operating DC VoltageTest.
ID eld.
6. Click Show Schematic to display a
diagram of the test setup and conrm that your test setup is correct.
7. In the Select panel, highlight the test and click Congure.
40 TekExpress HEAC Quick Start User Manual
8. Use the default values in the C ompliance
Mode to run the tests for compliance with the standards
NOTE. To change acquisition parameter
values, click User Dened Mode.A message appe make changes to a test, the test may no longer be compliant. Click OK to proceed with the User
9. Click Close.
10. In the Select panel, click Run to start the
test.
The application switches to the Acquire tab.
.
ars prompting you that If you
Dened Mode.
Application Exa
mples
TekExpress HEAC Quick Start User Manual 41
Application Exa
11. Click the Analyze tab.
12. The application displays the status of the
13. When the tests complete, the application
mples
tests in the Status Messages window. Click Save St
atus to save the status
messages.
shows a rep
ort in the Report panel.
42 TekExpress HEAC Quick Start User Manual
Single Mode Receiver Tests
Required equipment Model supported
Real-time osc
Arbitrary wa
Probe
HEAC TPA-
Test xt
DUT
SMA Cables Tektronix part number 174-1428-00 (1.5 meter)
HDMI Cable HDMI cable with H EAC capability
illoscope
veform generator
P adapter
ure
Application Exa
Tektronix DPO7000 Series, DPO70000 Series, DPO70000B Series, DSA70000 Series, DSA70000B Series, and MSO70000 Ser
Tektronix AW Series, or AWG7000B Series Arbitrary Waveform Generator
Tektronix P6243 or P6245 for Tektronix DPO70000 Series, DPO70000B Series, DSA70000 Series, and DSA70000B Mixed Oscilloscopes
Tektronix P6243, P6245, or TAP1500 for Tektronix DPO7000 Se
Tektroni
TF-HEAC TF-HDMID-TPA-KIT
An HEAC sink or source device
Tektronix part number 174-1341-00 (1 meter)
ies Digital and Mixed Signal Oscilloscopes
G5000 Series, AWG5000B Series, AWG7000
Series, and MSO7000 Series Digital and
ries Digital Oscilloscopes
x HEAC-TPA-P
-TPA-P (A/C) or TF-HEAC-TPA-KIT,
mples
TekExpress HEAC Quick Start User Manual 43
Application Exa
This tests the DUT for compliance with single mode (Receiver) tests.
mples
1. Connect the DU
T to the equipment as shown.
44 TekExpress HEAC Quick Start User Manual
Application Exa
Connect the HEAC-TPA plug board to the HEAC connector on the Source DUT.
Connect the CEC or CDC Controller to the CEC/CDC Control Port on the HEAC-TPA main board.
Connect the Ch1 Analog(+) output from a waveform generator to the HEAC+ SMA connector of the HEAC-TPA main board.
Set the Impedance Conversion Circuit on the HEAC-TPA main board to 55 Ω.
Connect a single-ended probe from Ch1 of the digital oscilloscope to the HEAC+ probe point on the HEAC-TPA main board.
mples
Set the HEAC
NOTE. Do not use +5 V power from the Source DUT.
Load the waveform data on the arbitrary waveform generator and generate the waveforms.
Activate the ARC (Single mode) transmission on the HEAC Sink D UT using the CEC/CDC c ontroller.
2. Select HEAC-Receiver as the device
type.
3. Select the SingleMode-Rx as the Test
Suite.
The default version CTS 1.4.
All the single mode receiver tests are select
4. Enter
ID eld.
5. Click Show Schematic to display a
diagram of the test setup and conrm
your test setup is correct.
that
he Select panel, highlight the test and
6. In t
click Congure.
-TPA main to use +5 V power from the DC Power Supply.
ed by default.
the DUT identication in the DUT
TekExpress HEAC Quick Start User Manual 45
Application Exa
7. Use the default values in the Compliance
NOTE. To change acquisition parameter
values, click User Dened Mode.A message appe make changes to a test, the test may no longer be compliant. Click OK to proceed with the User
8. Click Close.
mples
Mode to run the tests for compliance with the standards
.
ars prompting you that If you
Dened Mode.
9. Click Run i
The application switches to the Acquire tab.
10. Click the Analyze tab.
11. The application displays the status of the
tests in the Status Messages window. Click Save Status to save the status messages.
n the Select panel.
46 TekExpress HEAC Quick Start User Manual
Application Exa
mples
12. Thesinglemode
receiver tests are run at
three terminal voltage levels (Vel): 0 V,
2.5 V, and 5 V.
13. The applica
tion prompts you to verify
the audio response from the DUT. Click Detected or Not Detected as appropria
te for each test.
14. Repeat Steps 13 and 14 for different
terminal voltage levels and audio patterns of various frequencies.
15. When the tests complete, the application
shows a report in the Report panel.
TekExpress HEAC Quick Start User Manual 47
Application Exa
mples
Single Mode Operating DC Voltage Test (Receiver)
Required equipment Model supported
Real-time osc
Arbitrary wa
Probe
HEAC TPA-
Test xt
DUT
SMA Cables Tektronix part number 174-1428-00 (1.5 meter)
HDMI Cable HDMI cable with HEAC capability
illoscope
veform generator
P adapter
ure
Tektronix DPO7000 Series, DPO70000 Series, DPO70000B Series, DSA 70000 Series, DSA70000B Series, and MSO70000 Ser
Tektronix AW Series, or AWG7000B Series Arbitrary Waveform Generator
Tektronix P6243 or P6245 for Tektronix DPO70000 Series, DPO70000B Series, DSA70000 Series, and DSA70000B Mixed Oscilloscopes
Tektronix P6243, P6245, or TAP1500 for Tektronix DPO7000 Se
x HEAC-TPA-P
Tektroni
TF-HEAC TF-HDMID-TPA-KIT
An HEAC source device
Tektronix part number 174-1341-00 (1 meter)
ies Digital and Mixed Signal Oscilloscopes
G5000 Series, AWG5000B Series, AWG7000
Series, and MSO7000 Series Digital and
ries Digital Oscilloscopes
-TPA-P (A/C ) or TF-HEAC-TPA-KIT,
ests the DUT for compliance with single mode operating DC voltage (Receiver) tests.
This t
48 TekExpress HEAC Quick Start User Manual
1. Connect the DUT to the equipment as shown.
Application Exa
mples
Connect the HEAC-TPA plug board to the HEAC connector on the Source DUT.
Connect the CEC or CDC Controller to the CEC/CDC Control Port on the HEAC-TPA main board.
Connect the Ch1 Analog(+) output from a waveform generator to the HEAC+ SMA connector of the HEAC-TPA main board.
Set the Coupling & Impedance Conversion Circuit on the HEAC-TPA main board to 55 Ω.
Connect a single-ended probe from Ch1 of the digital oscilloscope to the HEAC+ probe point on the HEAC-TPA main
rd.
boa
the HEAC-TPA main board to enable the Source DUT test, and to use +5 V power from the DC Power Supply. Set
Set switch S7 to the right (On position) on the HEAC-TPA main xture.
NOTE. Do not use +5 V power from the Source DUT.
Connect and set the DC Power Supply to supply +5 V to the HEAC-TPA main board.
Power on the Source DUT.
Activate the ARC (Single mode) transmission on the HEAC Source DUT using the CEC/CDC controller.
Load the nominal audio waveform data on the arbitrary waveform generator and generate the waveform.
TekExpress HEAC Quick Start User Manual 49
Application Exa
2. Select HEAC-Receiver as the device
3. Select the SingleMode-Rx as the Test
4. Click Deselect All and select the
mples
type.
Suite.
The default version CTS 1.4.
Operatin
g DC Voltage test.
5. Enter th
6. Click Show Schematic to display a
7. In the
e DUT identication in the DUT
ID eld.
diagram of the test setup and conrm
ur test setup is correct.
that yo
Select panel, highlight the test and
click Congure.
50 TekExpress HEAC Quick Start User Manual
8. Use the default values in the C ompliance
Mode to run the tests for compliance with the standards
NOTE. To change acquisition parameter
values, click User Dened Mode.A message appe make changes to a test, the test may no longer be compliant. Click OK to proceed with the User
9. Click Close.
10. Click Run in the Select panel.
The application switches to the Acquire tab.
.
ars prompting you that If you
Dened Mode.
Application Exa
mples
TekExpress HEAC Quick Start User Manual 51
Application Exa
11. The operating DC voltage test runs at
mples
three terminal voltages: 0 V, 2.5 V, and 5 V. Adjust the
voltage and click OK to
continue.
52 TekExpress HEAC Quick Start User Manual
12. Click the Analyze tab.
13. The application displays the status of the
tests in the Status Messages window. Click Save St
atus to save the status
messages.
14. When the tests complete, the application
shows a rep
ort in the Report panel.
Application Exa
mples
TekExpress HEAC Quick Start User Manual 53
Application Exa
mples
54 TekExpress HEAC Quick Start User Manual
Index
Index
A
Acquire, 8 Analyze, 8, 13, 17, 21, 27, 32 Arbitrary waveform generator, 29,
33, 38, 43, 48
C
Common mode
receiver, 35
Complianc
Congure, 6
Conforma
Connect
Connections
e mode, 6, 12, 16, 20,
26, 31, 32, 35, 41, 46, 51
Acquire pa Analyze panel, 7 Comments panel, 7 Limits pa receiver test, 31, 35, 40, 45, 50 transmitter test, 12, 16, 20, 26
CTS 1.4 specications, vi HDMI 1.4 standards, vi
equipment, 2
common
common mode tests, 34 differ
diffe
single mode receiver tests, 44,
nel, 7
nel, 7
nce
mode receiver
tests, 34
ential mode transmitter, 11, 15, 19, 25
rential receiver tests, 30,
39, 49
45
D
Device, 6 Differential mode
rating DC Voltage test, 14
Ope receiver, 31, 40, 50 transmitter, 12, 16, 20
ferential m ode Operating DC
Dif
Voltage transmitter tests Probe, 14
al-time oscilloscope, 14
Re
Differential mode transmitter
tests, 10
DUT, 10, 14, 18, 24, 29, 33
id, 8
DUT IP Address, 31
H
HDMI Cable, HTML report, vi
10
J
Jumper setup, 5
M
Multiple
tests, 6
P
Pass/Fail notication, vi Probe, 10, 18, 24, 29
R
Readme Real-time oscilloscope, 10, 18, 24,
Recei
Related documentation, vii Report, 13, 17, 23, 28, 32
Run
,1
29, 38, 43, 48
ver test common mode, 33 differential mode, 29, 38, 48
le mode, 44
sing
rate, 9
gene HTML, 9 previewing, 9
nt, 9
pri printing, 9 save, 9
ing, 9
sav
test, 8
S
fety Summary, iii
Sa
Show Schematic, 2, 6, 12, 16, 20,
26, 31, 35, 40, 45, 50
Single mode
receiver, 45
transmitter, 26 SMA Cables, 1 Software
closing the, 2
features, v
installation, 1
process ow, 3
starting t
upgrades, vii Status messages, 8, 13, 17, 21, 27,
32 Switch setup, 4
0
i
he, 2
T
Test
ing, 6
congur
details, 9
interpreting the result, 9
ers, 6
paramet
report, 9
running, 8
ing, 6
select Test xture, 10, 14, 18, 24, 29, 30,
33, 39, 45, 49
AC-TPA-KIT, 2
TF-HE Test suite, 6, 12, 16, 20, 26, 31, 35,
40, 45, 50
on, 6
versi Tests
Deselect All, 6
ct All, 6
Sele Transmitter test
differential mode, 10, 14, 19,
25
Transmitter tests
Operating DC Voltage test, 14
U
rdefined mode, 13, 17, 20, 26,
Use
32, 35
TekExpress HEAC Quick Start User Manual 55
Loading...