Tektronix TDS7254, TDS7404, CSA7404, CSA7404B, TDS7254B Reference manual

Getting Started with TDSHT3

You can use this side of the quick reference card to get
started with the Source Clock--Data Tests Select All test
procedure. The other side contains a complete menu tree for
the TDSHT3 HDMI Compliance Test Software.

NOTE. For additional procedures, refer to the

TDSHT3 Quick Start User Manual. For
complete operating instructions, refer to the
online help.

TDSHT3 HDMI Compliance Test Software enables
unprecedented efficiency by providing a comprehensive
range of tests, including Jitter Tolerance. Start the
application by using Analyze > HDMI Compliance Test
Software(1.3) or App > HDMI Compliance Test
Software(1.3).

Source Clock --Data Tests Select All

This option enables you to run the Eye Diagram, Duty
Cycle, Rise Time, Fall Time, and Clock Jitter
simultaneously.

You will need one supported oscilloscope, two differential
probes, one DC power supply 3.3 V, one EDID emulator,
and one HDMI EFF--TPA --P fixture.

Follow these steps:

1. On the menu bar, click Tes ts > Select > Source.

2. In the clock--data tests pane, click Select All.

4. To connect the DUT, click Tests > Connect.

5. Make the connections as follows:

8. If you have run the tests successfully, the software

makes Result available automatically and displays the
eye diagram plot and the clock jitter plot. Y ou can also
view both the result summary of the test and the report
configuration in the result pane.

9. In the result summary pane, click Result Details to

display the results of the tests.

10. In the Result Details dialog box, click Result Statistics

to display statistics based on the tests.

3. To change the configuration settings, click Test s >

Configure. For most tests, you can use the factory

default configuration. However, you can change the
values by using the virtual keyboard or the general
purpose knob on the oscilloscope front panel. You can
also restore the factory defaults or save and recall your
own configuration settings.

For up-to-date information on Tektronix oscilloscope
solutions for HDMI Compliance Test Software, access the
www.tektronix.com

TDSHT3 Ordering Information

This software supports the TDS6000B, TDS6000C,
TDS7254/TDS7254B, TDS7404/TDS7404B, CSA7404/
CSA7404B, TDS7704B, and DPO70000 series of
oscilloscopes. Refer to the Optional Applications Software
on Windows-Based Oscilloscopes Installation Manual for a
list of specific models. The applications CD includes a PDF
file of the online help.

To order along with oscilloscope:

H Opt. HT3 -- HDMI Compliance Test So ftware

To order an upgrade for an existing oscilloscope:

H TDS6000B -- Order TDS6BUP -- Opt. HT3

H TDS7000/B -- Order TDS7UP/7BUP -- Opt. HT3

H CSA7000/B -- Order TDS7UP/7BUP -- Opt. HT3

H DPO70000 -- Order DPO7UP -- Opt. HT3

To order an upgrade from HDMI 1.2a to HDMI 1.3a
compliance test software:

H TDS6000B -- Order TDS6BUP -- Opt. HT23

H TDS7000/B -- Order TDS7UP/7BUP -- Opt. HT23

H CSA7000/B -- Order TDS7UP/7BUP -- Opt. HT23

H DPO70000 -- Order DPO7UP -- Opt. HT23

NOTE. You will be provided with two

TDSHT3 applications, one supporting
CTS 1.2a specification, displayed as
TDSHT3, and the other for CTS 1.3a
specification, displayed as TDSHT3v1.3. Both
applications can be loaded onto the
oscilloscope, but you can run only one
application at a time.

Web page.

6. Ensure that your signal in the oscilloscope display is

similar to the sample signal. Click View Waveform to
display a sample of the expected signal. If the displays
are not similar, go back and check your configuration
and connections.

7. Click Run Test to perform the test. The TDSHT3

HDMI Compliance Test Software sets up the
oscilloscope and the test runs displaying a progress
indicator.

Recommended Accessories

Oscilloscopes

H 16 M Record Length/Ch: Opt. 4 M or more (Eye

Diagram and Jitter tests)

HDMI Pattern Sources

H Jitter Generation: AWG7102/AWG710/AWG710B/

AFG3000 (minimum two channel AFG) for Sink tests

H Test Pattern Generation: DTG5274/DTG5334,

DTGM30 (three required), and DTGM32 (one required
for AFG3000/AWG710/AWG710B) for sink tests

TDR Tests

H Oscilloscope: TDS8200B/DSA8200 with 80E03 and

80E04 modules

Probes

H Differential Probes: P7313SMA for both single-ended

and differential measurements. P7350SMA can be used
for differential tests of limited resolutions.

H Active Probes: P7240 (two probes) for single ended

measurements using old fixtures.

H Probe Positioner: PPM100 Flexible Arm Probe Posi-

tioner.

Tes t Fix tures

H Plug type: EFF-- HDMI--TPA--P, available from Efficere

Technologies

H Receptacle type: EFF--HDMI--TPA--R, available from

Efficere Technologies

H Receptacle type: HDMI TPA--R adapter set --

013--A012--50 (can be used for limited resolution)

H Plug type: HDMI TPA--P adapter set -- 013-- A013--50

(can be used for limited resolution)

The software calculates statistics for each selected test, and
logs the statistics on a cycle--by--cycle basis in a fairly large
waveform. The standard statistics are for the Maximum,
Minimum, Mean, Standard Deviation, and Population.

TDSHT3
HDMI Compliance Test Software
Reference Source Test

www.tektronix.com

*P071195902*

071-1959-02

TDSHT3 Menu Tree

File

Recall Default
Recall
Save
Recall Recent
Preferences
Minimize
Exit

Position Eye Mask in Center
Acquisition Alert Message

Tes ts

Results

Utilities

Select

Configure

Connect

View Waveform

Summary
Details

Report Generator
Deskew

DTG PatternList

Source
Sink
Cable

Source

Sink

Cable

De fine Test Te mpla te
Define Report Layout
Generate Report

Eye Diagram
Duty Cycle
Rise Time
Fall Time
Clock Jitter
Inter--Pair Skew (Data--Data Tests)
Intra--Pair Skew
Low Amplitude +
Low Amplitude

Min/Max--Diff Swing Tolerance
Jitter Tolerance
Intra--Pair Skew

Eye Diagram

–

Help

Help Topics
About TDSHT3

Copyright © Tektronix, Inc.