Tektronix TDS7254, TDS7404, CSA7404, CSA7404B, TDS7254B Reference manual

Getting Started with TDSHT3

You can use this side of the Quick Reference Card to get
started with the Source Clock--Data Tests Select All test
procedure. The other sidecontains a complete menu tree for
the TDSHT3 HDMI Compliance Test Software.

NOTE. For additionalprocedures, referto the

QuickStart User Manual.Forcomplete
operating instructions, referto the Online
Help.

TDSHT3 HDMI Compliance TestSoftwareenables
unprecendented efficiencybyprovidingacomprehensive
range of tests, including Jitter Tolerance.

Source Clock--Data Tests Select All

Thisoptionenables you to run theeye diagram,dutycycle,
rise time, falltime, clock jitter, over/undershootv--h,
over/undershoot v--l, and inter--pairskew test
simultaneously.

You will needone supported oscilloscope, two differential
probes,one DCpowersupply 3.3V, oneEDIDemulator,
and one TPA--P--DI fixture.

Follow these steps:

1. On the menu bar, click Tests > Select > Source.

2. In the clock--data tests pane, click Select All.

4. Toconnect the DUT, click Tests > Connect.

5. Maketheconnectionsasfollows:

8. Ifyou haverun thetests successfully, the software

makesResultavailable automatically and displays the
eye diagram plot and the clock jitter plot. You can also
viewboththeresult summaryofthetest and the report
configuration in the result pane.

9. In theresult summarypane,click Result Details to

display the results of the tests.

10. In the Result Details dialogbox,click Result Statistics

to display statisticsbased on the tests.

3. To change the configuration settings,click Tests >

Configure. For most tests, you canusethe factory

default configuration. However,youcanchange the
valuesby usingthevirtual keyboardorthegeneral
purposeknobon the oscilloscope front panel. Using the
Filemenu,you canalso restorethefactory defaults or
save and recall yourown configuration settings.

For up-to-date information on Tektronix oscilloscope
solutions for HDMI Compliance Test Software, access
the www.tektronix.com

TDSHT3 OrderingInformation

Thissoftware supportstheTDS6000B,TDS6000C,
TDS7254/B,TDS7404/B,CSA7404/B,andTDS7704B
series of oscilloscopes. Refer to the OptionalApplications

Software on Windows-BasedOscilloscopes Installation
Manual foralistof specificmodels. The applications CD

includes a PDF fileof the online help.

Web page.

6. Ensurethat your signal in the oscilloscope display is

similar to the sample signal. Click View Waveform to
display a sample of the expected signal. If the displays
arenotsimilar,gobackandcheck your configuration
and connections.

7. Click Run Test to perform the test. The TDSHT3

HDMICompliance Test Softwaresets up the
oscilloscope and the test runs displaying a progress
indicator.

Toorder along with oscilloscope:
H Opt. HT3 -- HDMI ComplianceTest Software

To order an upgrade for an existingoscilloscope:

H TDS7000/B -- Order TDS7UP/7BUP -- Opt. HT3
H CSA7000/B -- Order TDS7UP/7BUP -- Opt. HT3

Recommended Accessories
Oscilloscopes

H 16M RecordLength/Ch -- Opt. 4M or more (for Eye

Diagram and Jitter tests)

H Serial Trigger-- Opt. ST (for Inter--pairSkewtests)

HDMI Pattern Sources

H Jitter Generation -- AWG710B (for Sink tests)
H Test Pattern Generation -- DTG5274 and DTGM30 for

Sink Tests (three required)

TDR Tests

H Oscilloscope -- TDS8000B with 80E03 and 80E04

modules

Probes

H Differential Probes -- P6330,P7330 and P7350 (two

probesrequired)

H ActiveProbes -- P7240 and above(twoprobesrequired)
H ProbePositioner -- PPM100 FlexibleArm Probe Posi-

tioner

Test Fixtures

H Plug type -- HDMI TPA--P adapterset -- 013--A013--50
H Receptacle type -- HDMI TPA--R adapter set --

013--A012-- 50

The software calculates statistics for each selected test, and
logs the statistics on a cycle--by--cycle basis in a fairly large
waveform. The standardstatistics are fortheMaximum,
Minimum,Mean, StandardDeviation,and Population.

TDSHT3
HDMI Compliance Test Software
Reference
Source Test

www.tektronix.com

*P071156601*

071-1566-01

TDSHT3 Menu Tree

File

Recall Default
Recall
Save
Recall Recent
Preferences
Minimize
Exit

Position Eye Mask in Center
Acquisition Alert Message
Trigger (Rise/Fall Time or Over/Undershoot)

Pulse Width
Edge Trigger

Tes ts

Results

Utilities

Select

Configure

Connect

View Waveform

Summary
Details

Report Generator
Deskew

Source
Sink
Cable

Source

Sink

Cable

De f ine Tes t Tem plate
Define Report Layout
Generate Report

Eye Diagram
Duty Cycle
Rise Time
Fall Time
Clock Jitter
Over/Undershoot V--H
Over/Undershoot V--L
Inter--Pair Skew (Clock--Data Tests)
Inter-- Pair Skew (Data--Data Tests)
Intra-- Pair Skew
Low Amplitude +
Low Amplitude --

Min--Diff Sensitivity
Jitter Tolerance
Intra-- Pair Skew

Eye Diagram

Help

Help Topics
About TDSHT3

Copyright Tektronix,Inc.