Tektronix TDS700D, TDS600C, TDS500D User Manual

Supplement
TDS 500D, TDS 600C & TDS 700D Digitizing Oscilloscopes
071-0273-03
This document supports firmware version 5.1 and above.
*P071027303*
071027303
Copyright © Tektronix, Inc. All rights reserved.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes that in all previously published material. Specifications and price change privileges reserved.
Printed in the U.S.A.
Tektronix, Inc., P.O. Box 1000, Wilsonville, OR 97070--1000
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

TDS 600C Features

Most TDS 600B information in the TDS 500D, TDS 600B, & TDS 700D Digitizing Oscilloscopes User manual is valid for the TDS 654C, TDS 680C,
and TDS 684C oscilloscope models. This supplement lists the differences between the TDS 600C and the TDS 600B models.

Key Features

Except for the differences outlined in this manual, the TDS 600C is identical to a TDS 600B. Most of the information in your user manual (and other TDS documentation) that applies to the TDS 600B also applies to the TDS 600C.
Table 1 lists the key features of the oscilloscope models. The pages that follow list the new TDS 600C features.
Table 1: Key Features and differences of models
Feature 520D 540D 580D 654C 680C 684C 724D 754D 784D 794D
No. of channels 2+2
1
4 4 4 2+2
1
4 2+2
1
4 4 4 Digitizing rate, max. 2 GS/s 4 GS/s 5 GS/s 2 GS/s 4 GS/s No. of Channels. at max-
imum rate Analog Bandwidth 500 MHz 1GHz 500 MH
Record Lengths, max. To 50K/Channel DPO Acquisitions Yes No Yes Hi Res Acquisitions Yes No Yes Advanced DSP Math Communication Signal
Analyzer Reference Receiver Option 3C and 4C No Option 3C and 4C No
3
1 2 1 4 2 4 1 2 1
1GHz 500 MHz 1GHz 2GHz
z
2
Option 2F Standard Option 2C No Option 2C
To 15K/Channel To 50K/Channel
4
2
TDS 500D, TDS 600C & TDS 700D Supplement
1
TDS 600C Features
Table 1: Key Features and differences of models (Cont.)
Feature 794D784D754D724D684C680C654C580D540D520D
Storage,
Floppy Disk Hard Disk Zip Drive Support
I/0 includes RS--232 and Centronics
5
Option 13 Standard
Input Impedance 50 and1M 50 Ω
Standard
Option HD
Standard
4
only
Measurement statistics
Standard (mean, min, max, and std dev
Waveform Histograms Standard Java-based Applications Available Display Mono Color Mono Color
1
Two plus Two channel operation allows two of four channels to be displayed simultaneously. Channels not displayed can be used to couple a triggering signal to the oscilloscope.
2
These TDS models can be purchased with Option 1M or Option 2M, which add longer record length settings (up to 2 Mb/channel). See Option 1M and Option 2M on pages 4 and 5.
3
Advanced digital signal processing provides FFTs, integrals, and derivatives of waveforms. See Option 2F on page 5.
4
Standard denotes a standard product feature as opposed to a feature included as part of an option.
5
GPIB I/O included with all models.
Display Histograms
The TDS 600C can display histograms as described in the TDS 500D, TDS 600B & TDS 700D Digitizing Oscilloscopes User Manual.
Select an Application
The TDS 600C can select and load Java-based applications in the APPLICA­TION menu as described in the TDS 500D, TDS 600B & TDS 700D Digitizing Oscilloscopes User Manual. Then you can control the application using the APPLICATION menus.
2
TDS 500D, TDS 600C & TDS 700D Supplement
TDS 600C Features
Option HD
Iomega Zip Drive Support
Display Measurement
Statistics
Take Optical
Measurements
External Attenuation
Probe Calibration
If your TDS 600C contains the optional hard disk, you can use it to save and recall waveforms, setups, and hard copies as described in the TDS 500D, TDS 600B & TDS 700D Digitizing Oscilloscopes User Manual. With this option, you can also run Java-based application programs.
The TDS 600C is compatible with Iomega 100 Mbyte Zip drives as described in the TDS 500D, TDS 600B & TDS 700D Digitizing Oscilloscopes User Manual.
The TDS 600C can display statistics about a measurement as described in the TDS 500D, TDS 600B & TDS 700D Digitizing Oscilloscopes User Manual.
The TDS 600C can take Extinction Ratio, Extinction Percent, Extinction dB, and Mean dBm measurements as described in the TDS 500D, TDS 600B & TDS 700D Digitizing Oscilloscopes User Manual.
The TDS 600C can set External Attenuation as described in the TDS 500D, TDS 600B & TDS 700D Digitizing Oscilloscopes User Manual.
On the TDS 600C, use the TDS 500D and TDS 700D procedures to calibrate a probe as described in the TDS 500D, TDS 600B & TDS 700D Digitizing Oscilloscopes User Manual.
TDS 500D, TDS 600C & TDS 700D Supplement
3
TDS 600C Features

Options

Tektronix will ship the options shown in Table 2:
Table 2: Options
Option # Label Description
A1 Universal European
power cord A2 UK power cord 240 V, 50 Hz power cord A3 Australian power cord 240 V, 50 Hz power cord A4 North American power
cord A5 Switzerland power cord 220 V, 50 Hz power cord HD Hard disk drive Addaharddisk. 05 Video trigger Oscilloscope comes with tools for investigating events that occur when a video signal
13 RS-232/Centronics Hard-
copy Interface Ports 1G 1 GS/s maximum Limit sample rate to 1 GS/s maximum.
1K Scope cart K420 scope cart. This cart can help transport the oscilloscope around many lab environ-
1M
130,000 record length
220 V, 50 Hz power cord
240 V, 60 Hz power cord
generates a horizontal or vertical sync pulse. These tools allow investigation of a range of NTSC, PAL, SECAM, and high definition TV signals. (Option is not available on the TDS 794D.)
Add RS-232-C and Centronics interface ports. (Option applies to TDS 500D only.)
(Option applies to TDS 520D, TDS 540D, TDS 724D, and TDS 754D only.)
ments. Extend record length from 50,000 samples standard as follows:
TDS 520D and TDS 724D: To 250,000 samples on one channel and 130,000 on two channels
TDS 540D, TDS 580D, TDS 754D, TDS 784D, and TDS 794D: To 500,000 samples on one channel, 250,000 on two channels, and 130,000 samples on three or four channel s
(Option is only available for the models listed above.)
4
TDS 500D, TDS 600C & TDS 700D Supplement
Table 2: Options (cont.)
Option # DescriptionLabel
TDS 600C Features
2M
1R Rackmount Oscilloscope comes configured for installation in a 19 inch
2C
3C P6701B with system
4C P6703B with system
31 Buffered passive probe Add a 500 MHz P6339A 10x, buffered passive probe
32 Active probe Adda4GHzP6217 active probe
33 Low capacitance probe Add a 3.0 GHz (probe only) P6158 20x, 1 k, low capacitance probe
34 Differential probe Adda1GHz(probeonly)P6247 differential probe 35 Active probe Adda1GHz(probeonly)P6243 active probe
36 Passive probe Add a 500 MHz P6139A 10X passive probe
37 Active probe Add a 1.5 GHz P6245 active probe
2F
8 M acquisition length
Communication Signal Analyzer
calibration
calibration
Advanced DSP math
Extend standard acquisition length as follows: TDS 520D and TDS 724D: To 2 M samples on two channels and 4 M on one channel TDS 540D, TDS 580D, TDS 754D, TDS 784D, & TDS 794D: To 2 M samples on three or
four channels, 4 M on two channels, and 8 M samples on one channel (Option includes a hard disk and is only available for the models listed above.)
wide instrument rack. For later field conversions, order kit # 016-1236-00. Oscilloscope comes configured for communications signal triggering and mask testing.
(Option applies to TDS 500D & TDS 700D only.) Oscilloscope comes with a P6701B and calibrated short-wavelength optical reference
receiver on channel 1. (Option applies to TDS 500D & TDS 700D only, except TDS 794D.) Oscilloscope comes with a P6703B and calibrated long-wavelength optical reference
receiver on channel 1. (Option applies to TDS 500D & TDS 700D only, except TDS 794D.)
(Option applies only to TDS 794D.)
(Option applies only to TDS 794D.)
(Option applies only to TDS 580D, TDS 680C, TDS 684C, TDS 784D, and TDS 794D.)
(Option applies only to TDS 754D, TDS 724D, TDS 540D, and TDS 520D.)
(Option applies only to TDS 784D, TDS 600C, and TDS 580D.)
(Option applies only to TDS 794D, TDS 784D, TDS 680C, TDS 684C, and TDS 580D.) Add advanced DSP math features such as FFT, integration, and differentiation.
(Option applies only to TDS 500D models.)
TDS 500D, TDS 600C & TDS 700D Supplement
5
TDS 600C Features
Table 2: Options (cont.)
Option # DescriptionLabel
C3 Three years calibration Provides three years of calibration C5 Five years calibration Provides five years of calibration D1 Calibration data report Oscilloscope comes with a calibration data report. D3 Calibration data for C3 Provides calibration data for option C3 D5 Calibration data for C5 Provides calibration data for option C5 R5 Extended Warranty Oscilloscope comes witha5yearextended warranty. L1
Manuals in French
Provides Language versions of User Manual, according to option number chosen. L3 L5 L9
Manuals in German Manuals in Japanese Manuals in Korean

Standard Accessories

The oscilloscope comes standard with the accessories listed in Table 3.
Table 3: Standard accessories
Accessory Part number
User Manual with Programmers Manual Help Disk 071-0130-XX Reference 020-2313-XX Technical Reference: Performance Verification and Specifications 071-0630-XX Probes:
TDS 754D and TDS 540D:
Four P6139A 10X, 500 MHz Passive probes TDS 654C: Four P6243 1 GHz Active probes TDS 724D and TDS 520D:
Two P6139A 10X, 500 MHz Passive probes TDS 794D, TDS 784D, TDS 684C, TDS 680C, TDS 580D:
No probes standard
P6139A P6243
P6139A
Front Cover 200-3696-01 Accessory Pouch (TDS 654C, TDS 684C, TDS 700D) 016-1268-00 U.S. Power Cord 161-0230-01
6
TDS 500D, TDS 600C & TDS 700D Supplement

Optional Accessories

TDS 600C Features
You can also order the optional accessories listed in Table 4.
Table 4: Optional accessories
Accessory Part number
Service Manual 071-0627-XX Oscilloscope Cart K420 Rack Mount Kit (for field conversion) 016-1236-00 Accessory Pouch (TDS 500D and TDS 680C) 016-1268-00 Soft-Sided Carrying Case 016-0909-01 Transit Case 016-1135-00 GPIB Cable (1 meter) 012-0991-01 GPIB Cable (2 meter) 012-0991-00 Centronics Cable 012-1214-00 RS-232 Cable 012-1298-00
TDS 500D, TDS 600C & TDS 700D Supplement
7
TDS 600C Features
Accessory Probes
Table 5 lists the recommended probes for each oscilloscope.
Table 5: Recommended probe cross reference
Probe 520D
540D
Passive
1X 10X P6139A P6139A P6139A P6139A P6139A P6139A P6339A 100X P5100 P5100 P5100 P5100 P5100 P5100
1000X P6015A P6015A P6015A P6015A P6015A P6015A SMD P6563A P6563A P6563A P6563A P6563A P6563A Low Capacitance P6158 P6158 P6158 P6158 Active CMOS/TTL P6243 P6245 P6243 P6245 P6243 P6245 P6245 Active, High Bandwidth P6245
Logic P6408 P6408 P6408 P6408 P6408 P6408 Differential Digital/
Telecom Micro Volt ADA400A ADA400A ADA400A ADA400A ADA400A ADA400A
P6101B P6101B P6101B P6101B P6101B P6101B
P6246,
P6247
580D 654C 680C
684C
P6245
P6217
P6247 P6246,
P6247
P6217
P6247 P6246,
724D 754D
P6247
784D 794D
P6245 P6217
P6247 P6247
P6245 P6217
High Voltage P5205
P5210
Current AC Only
Current AC/DC
Electro-Optical Converter P6701B
P6021 P6022
CT-1 CT-2
TCP202
AM503S
P6703B
P5205 P5210
P6021 P6022
CT-1 CT-2
TCP202
AM503S
P6701B P6703B
P5205 P5210
P6021 P6022
CT-1 CT-2
TCP202
AM503S
P6701B P6703B
P5205 P5210
P6021 P6022
CT-1 CT-2
TCP202
AM503S
P6701B P6703B
P5205 P5210
P6021 P6022
CT-1 CT-2
TCP202
AM503S
P6701B P6703B
P5205 P5210
P6021 P6022
CT-1 CT-2
TCP202
AM503S
P6701B P6703B
CT-1 CT-2
TCP202
AM503S
P6701B P6703B
8
TDS 500D, TDS 600C & TDS 700D Supplement
Supplément
Oscilloscopes numériques TDS 500D, TDS 600C & TDS 700D
071-0273-03
Le présent document s’applique aux versions ma­térielles 5.1 et ultérieures.
Copyright Tektronix, Inc. Tous droits réservés.
Les produits Tektronix sont protégés par des licences américaines et étrangères, publiées et en attente de publication. Les informations contenues dans le présent manuel remplacent et annulent toute documentation publiée antérieurement. Les changements de spécifications et de prix sont sous réserve.
Imprimé aux Etats-Unis.
Tektronix, Inc., P.O. Box 1000, Wilsonville, OR 97070–1000
TEKTRONIX, TEK et TEKPROBE sont des marques déposées de Tektronix, Inc.

Fonction du TDS 600C

La plupart des informations concernant le TDS 600B dans le Manuel d’utilisa­tion des oscilloscopes numériques TDS 500D, TDS 600B & TDS 700D sont aussi
valables pour les modèles TDS 654C, TDS 680C et TDS 684C. Ce supplément présente les différences qui existent entre les modèles TDS 600C et TDS 600B.

Fonctions principales

Hormis les différences soulignées dans le présent manuel, le TDS 600C est identique au TDS 600B. La plupart des informations contenues dans le manuel d’utilisation (et autre documentation TDS) qui s’appliquent au TDS 600B s’appliquent également au TDS 600C.
Le Tableau 1 contient une liste des fonctions principales des modèles d’oscillo­scope. Les pages qui suivent présentent les nouvelles fonctions du TDS 600C.
Table 1: Fonctions principales et différences entre modèles
Fonction 520D 540D 580D 654C 680C 684C 724D 754D 784D 794D
Nombre de voies 2+2
1
4 4 4 2+2
1
4 2+2
1
4 4 4
Vitesse de numérisa­tion, maxi.
Nombre de voies à débit maximal
Bande passante analo­gique
Longueurs d’enregistre­ment, maxi.
Acquisitions DPO Oui Non Oui Acquisitions Hi Res Oui Non Oui DSP évoluée Analyseur de signaux
de transmission Récepteur de référence Option 3C et 4C Non Option 3C et 4C Non
3
2 G-éch./s 4 G-éc h./s 5 G-éch./s 2 G-éch./s 4 G-éch./s
1 2 1 4 2 4 1 2 1
500 MHz 1GHz 500 MHz 1GHz 500 MHz 1GHz 2GHz
Jusqu’à 50 Ko/voie
Option 2F Standard
Option 2C Non Option 2C
2
Jusqu’à 15Ko/voie Jusqu’à 50Ko/voie
4
2
Oscilloscopes numériques TDS 500D, TDS 600C & TDS 700D
1
Fonction du TDS 600C
Table 1: Fonctions principales et différences entre modèles ( suite)
Fonction 794D784D754D724D684C680C654C580D540D520D
Stockage,
Disquette Disque dur Disquette Zip
E/S comprend RS–232 et Centronics
Impédance dentrée 50 et 1 M 50
5
Option 13 Standard
Standard
Option HD
Standard
4
unique-
ment
Statistiques de mesure (moyenne, min, max et écart type)
Histogrammes de signaux
Applications Java Disponible Ecran Monochrome Couleur Mono-
1
Le mode deux plus deux voies permet d’afficher simultanément deux des quatre voies. Les voies qui ne sont pas affichées peuvent servir à coupler un signal de déclenchement sur l’oscilloscope.
2
Il est possible d’acquérir ces modèles TDS avec l’Option 1M ou l’Option 2M, qui permettent des longueurs d’enregistrement plus grandes (jusqu’à 2 Mo/voie). Voir Option 1M et Option 2M aux pages 4 et 5.
3
Le traitement évolué des signaux numériques permet le calcul de FFT, d’intégrales et de dérivés de signaux. Voir Option 2Fàlapage5.
4
Le qualificatif « standard » désigne les fonctions standard par opposition aux fonctions faisant partie d’une option.
5
Tous les modèles sont dotés d’une E/S GPIB.
Standard
Standard
Couleur
chrome
Afficher des
histogrammes
Le TDS 600C peut afficher des histogrammes comme cela est expliqué dans le
Manuel dutilisation des oscilloscopes numériques TDS 500D, TDS 600B & TDS 700D.
Sélectionner une
application
Le TDS 600C permet la sélection et le chargement d’applications Java dans le menu APPLICATION, comme cela est décrit dans le Manuel dutilisation des oscilloscopes numériques TDS 500D, TDS 600B & TDS 700D.L’opérateur peut ensuite contrôler lapplication à laide des menus APPLICATION.
2
Oscilloscopes numériques TDS 500D, TDS 600C & TDS 700D
Fonction du TDS 600C
Option HD (disque dur)
Lecteur de disquettes Zip
Iomega
Afficher des statistiques
de mesure
Procéder à des mesures
optiques
Si votre TDS 600C est équipé du disque dur disponible en option, vous pouvez utiliser celui-ci pour sauvegarder et rappeler des signaux, des configurations, ainsi que pour faire des sorties imprimées, conformément aux instructions du
Manuel dutilisation des oscilloscopes numériques TDS 500D, TDS 600B & TDS 700D. Avec cette option, vous pouvez également utiliser des programmes
dapplication Java.
Le TDS 600C est compatible avec le lecteur de disquettes Zip Iomega de 100Mo, comme cela est expliqué dans le Manuel dutilisation des oscilloscopes numériques TDS 500D, TDS 600B & TDS 700D.
Le TDS 600C peut afficher des statistiques relatives à une mesure, comme cela est expliqué dans le Manuel dutilisation des oscilloscopes numériques TDS 500D, TDS 600B & TDS 700D.
Le TDS 600C peut effectuer des mesures de rapport dextinction, de pourcentage dextinction, de dB dextinction et de moyenne de dBm, comme cela est expliqué dans le Manuel dutilisation des oscilloscopes numériques TDS 500D, TDS 600B & TDS 700D.
Atténuation externe
Etalonnage des sondes
Le TDS 600C peut définir lAtténuation externe conformément à la description fournie dans le Manuel dutilisation des oscilloscopes numériques TDS 500D, TDS 600B & TDS 700D.
Sur le TDS 600C, utilisez les procédures TDS 500D et TDS 700D pour
étalonner les sondes conformément à la description fournie dans le Manuel dutilisation des oscilloscopes numériques TDS 500D, TDS 600B & TDS 700D.
Oscilloscopes numériques TDS 500D, TDS 600C & TDS 700D
3
Fonction du TDS 600C

Options

Tektronix peut expédier les options répertoriées dans le Tableau 2 :
Table 2: Options
Option n° Etiquette Description
A1 Cordon dalimentation universel
européen A2 Cordon dalimentation britannique Cordon dalimentation 240 V, 50 Hz A3 Cordon dalimentation australien Cordon dalimentation 240 V, 50 Hz A4 Cordon dalimentation nord améri-
cain A5 Cordon dalimentation suisse Cordon dalimentation 220 V, 50 Hz HD Disque dur Ajoute un disque dur. 05 Déclenchement vidéo Loscilloscope est livré avec les outils permettant d’étudier les événements qui
13 Ports dinterface dimpression
RS-232/Centronics 1G 1G-éch./s maximum Limite la fréquence d’échantillonnage à 1G-éch./s maximum. (Cette option ne
1K Chariot doscilloscope Chariot pour oscilloscope K420. Ce chariot facilite le transport de loscilloscope
1M Longueur denregistrement de
130000
Cordon dalimentation 220 V, 50 Hz
Cordon dalimentation 240 V, 60 Hz
surviennent lorsquun signal vidéogénère une impulsion synchronisée horizontale ou verticale. Ces outils autorisent également linvestigation dune gamme de signaux NTSC, PAL, SECAM et TV haute définition. (Cette option nest pas disponible sur le TDS 794D.)
Ajoute des ports dinterface RS-232-C et Centronics. (Cette option ne concerne que le TDS 500D.)
sapplique quaux TDS 520D, TDS 540D, TDS 724D et TDS 754D.)
dans les laboratoires. Etend la longueur denregistrement standard de 50000 échantillons de la
manière suivante :
TDS 520D et TDS 724D : à 250000 échantillons sur une voie et 130000 sur deux voies
TDS 540D, TDS 580D, TDS 754D, TDS 784D et TDS 794D : à 500000 échantillons sur une voie, 250000 sur deux voies et 130000 échantillons sur trois ou quatre voies
(Cette option est disponible uniquement pour les modèles cités ci-dessus.)
4
Oscilloscopes numériques TDS 500D, TDS 600C & TDS 700D
Table 2: Options (suite)
Option n° DescriptionEtiquette
Fonction du TDS 600C
2M Longueur dacquisition 8méga-
échantillons
1R Montage en baie Loscilloscope est livré configuré pour une installation dans une baie de 48,3 cm
2C
3C P6701B avec étalonnage du
4C P6703B avec étalonnage du
31 Sonde passive à mémoire tampon Ajoute une sonde passive à mémoire-tampon 10x de 500 MHz P6339A. (Cette
32 Sonde active Ajoute une sonde active de 4 GHz P6217. (Cette option concerne uniquement le
33 Sonde à faible capacité Ajoute une sonde de faible capacité de 3,0GHz (sonde uniquement)P6158, 20 x
34 Sonde différentielle Ajoute une sonde différentielle de 1 GHz P6247 (sonde uniquement). 35 Sonde active Ajoute une sonde active de 1GHz P6243 (sonde uniquement). (Cette option
36 Sonde passive Ajoute une sonde passive 10X de 500 MHz P6139A. (Cette option concerne
37 Sonde active Ajoute une sonde active de 1,5GHz P6245. (Cette option concerne uniquement
2F
Analyseur de signaux de transmis­sion
système
système
Fonctions DSP évoluées
Etend la longueur denregistrement standard de la manière suivante :
TDS 520D et TDS 724D : à 2Méga échantillons sur deux voies et 4 M sur une voie.
TDS 540D, TDS 580D, TDS 754D, TDS 784D & TDS 794D : à 2Méga échantillons sur trois ou quatre voies, 4 M sur deux voies et 8 Méga échantillons sur une voie.
(Cette option comprend un disque dur et est disponible uniquement pour les modèles cités ci-dessus.)
(19 pouces) de largeur. Pour des conversions ultérieures sur site, commander le kit réf. 016-1236-00.
Loscilloscope est livré configuré pour un déclenchement sur des signaux de transmission et des tests avec masque. (Cette option concerne uniquement les TDS 500D & TDS 700D.)
Loscilloscope est livré avec un récepteur P6701B de référence optique à ondes courtes étalonné sur la voie 1. (Cette option concerne uniquement les TDS 500D & TDS 700D, sauf le TDS 794D.)
Loscilloscope est livré avec un récepteur P6703B de référence optique à ondes courtes étalonné sur la voie 1. (Cette option concerne uniquement les TDS 500D & TDS 700D, sauf le TDS 794D.)
option concerne uniquement le TDS 794D.)
TDS 794D.)
1k. (Cette option concerne uniquement les TDS 580D, TDS 680C, TDS 684C, TDS 784D et TDS 794D.)
concerne uniquement les TDS 754D, TDS 724D, TDS 540D et TDS 520D.)
uniquement les TDS 784D, TDS 600C et TDS 580D.)
les TDS 794D, TDS 784D, TDS 680C, TDS 684C et TDS 580D.) Ajoute les fonctions DSP évoluées telles que FFT, intégration et différentiation.
(Cette option concerne uniquement les modèles TDS 500D.)
Oscilloscopes numériques TDS 500D, TDS 600C & TDS 700D
5
Fonction du TDS 600C
Table 2: Options (suite)
Option n° DescriptionEtiquette
C3 Trois années d’étalonnage Offre trois années d’étalonnage. C5 Cinq années d’étalonnage Offrecinqannées d’étalonnage. D1 Rapport de données d’étalonnage L’oscilloscope est livré avec un rapport de données d’étalonnage. D3 Données d’étalonnage pour C3 Offre des données d’étalonnage pour loption C3. D5 Données d’étalonnage pour C5 Offre des données d’étalonnage pour loption C5. R5 Garantie étendue Loscilloscope est livré avec une garantie étendue à 5 ans. L1
L3
Manuels en français
Manuels en allemand
Offre les versions de langues du Manuel dutilisation, en fonction du numéro doption choisi.
L5
L9
Manuels en japonais
Manuels en coréen

Accessoires standard

L’oscilloscope est livré en standard avec les accessoires répertoriés dans le Tableau 3.
Table 3: Accessoires standard
Accessoire No. de réf.
Manuel dutilisation avec Disque daide du Manuel Programmeurs 071-0130-XX Référence 020-2313-XX Référence technique : Vérification des performances et spécifications 071-0630-XX Sondes :
TDS 754D et TDS 540D :
Quatre sondes passives 10X, 500 MHz P6139A TDS 654C: Quatre sondes actives 1 GHz P6243 TDS 724D et TDS 520D :
Deux sondes passives 10X, 500 MHz P6139A TDS 794D, TDS 784D, TDS 684C, TDS 680C, TDS 580D :
Pas de sondes standard
P6139A P6243
P6139A
Couvercle de face avant 200-3696-01 Trousse pour accessoires (TDS 654C, TDS 684C, TDS 700D) 016-1268-00 Cordon dalimentation pour les Etats-Unis 161-0230-01
6
Oscilloscopes numériques TDS 500D, TDS 600C & TDS 700D

Accessoires en option

Fonction du TDS 600C
Il est également possible de commander les accessoires en option répertoriésdansle Tableau 4.
Table 4: Accessoires en option
Accessoire No. de réf.
Manuel de maintenance 071-0627-XX Chariot pour oscilloscope K420 Kit de montage en baie (pour conversion sur site) 016-1236-00 Trousse pour accessoires (TDS 500D et TDS 680C) 016-1268-00 Mallette de transport à parois souples 016-0909-01 Mallette de transport 016-1135-00 Câble GPIB (1 mètre) 012-0991-01 Câble GPIB (2 mètres) 012-0991-00 Câble Centronics 012-1214-00 Câble RS-232 012-1298-00
Oscilloscopes numériques TDS 500D, TDS 600C & TDS 700D
7
Fonction du TDS 600C
Sondes accessoires
Le Tableau 5 contient la liste des sondes recommandées pour chaque oscilloscope.
Table 5: Références des sondes recommandées
Sonde 520D
540D
Passive
1X 10X P6139A P6139A P6139A P6139A P6139A P6139A P6339A 100X P5100 P5100 P5100 P5100 P5100 P5100
1000X P6015A P6015A P6015A P6015A P6015A P6015A SMD P6563A P6563A P6563A P6563A P6563A P6563A Faible capacité P6158 P6158 P6158 P6158 Active CMOS/TTL P6243 P6245 P6243 P6245 P6243 P6245 P6245 Active, haute bande
passante Logique P6408 P6408 P6408 P6408 P6408 P6408 Numérique différentielle/
Telecom
P6101B P6101B P6101B P6101B P6101B P6101B
P6246,
P6247
580D 654C 680C
684C
P6245 P6217
P6247 P6246,
P6247
P6245 P6217
P6247 P6246,
724D 754D
P6247
784D 794D
P6245 P6217
P6247 P6247
P6245 P6217
Micro Volt ADA400A ADA400A ADA400A ADA400A ADA400A ADA400A Haute tension P5205
P5210
Courant alternatif uniquement
Courant alternatif/continu TCP202
Convertisseur électro-op­tique
P6021 P6022
CT-1 CT-2
AM503S
P6701B P6703B
P5205 P5210
P6021 P6022
CT-1 CT-2
TCP202
AM503S
P6701B P6703B
P5205 P5210
P6021 P6022
CT-1 CT-2
TCP202
AM503S
P6701B P6703B
P5205 P5210
P6021 P6022
CT-1 CT-2
TCP202
AM503S
P6701B P6703B
P5205 P5210
P6021 P6022
CT-1 CT-2
TCP202
AM503S
P6701B P6703B
P5205 P5210
P6021 P6022
CT-1 CT-2
TCP202
AM503S
P6701B P6703B
CT-1 CT-2
TCP202
AM503S
P6701B P6703B
8
Oscilloscopes numériques TDS 500D, TDS 600C & TDS 700D
Zusatz
Die Digitaloszilloskope TDS 500D, TDS 600C und TDS 700D
071-0273-03
Dieses Dokument unterstützt Firmware der V ersion 5.1 und höher.
Copyright E Tektronix Inc. Alle Rechte vorbehalten.
Die Tektronix-Produkte sind von amerikanischen und nicht-amerikanischen, erteilten und laufenden Patenten gedeckt. Die Informationen dieser Veröffentlichungen ersetzen die aller vorhergehenden. Die Spezifikationen und Preise können ohne Vor a nk ündigung geändert werden.
Gedruckt in U.S.A.
Tektronix Inc., P.O. Box 1000, Wilsonville, OR 97070–1000
TEKTRONIX und TEK sind eingetragene Warenzeichen von Tektronix Inc.

Funktionen des Modelle TDS 600C

Die meisten Informationen zum Modell TDS 600B im Benutzerhandbuch TDS 500D, TDS 600B, & TDS 700D Digitaloszilloskope gelten auch für die Oszilloskopmodelle
TDS 654C, TDS 680C und TDS 684C. In diesem Zusatz werden die Unterschiede zwischen den Modellen TDS 600C und TDS 600B beschrieben.

Wichtige Funktionen

Außer den hier beschriebenen Unterschieden entspricht das Oszilloskop TDS 600C dem Modell TDS 600B. Die meisten Informationen Ihres Benutzerhandbuchs (und anderer TDS-Dokumentationen), die auf das Modell TDS 600B zutreffen, gelten auch fürdas Modell TDS 600C.
In der nachfolgenden Tabelle 1 erhalten Sie einen Überblick über die wichtigsten Funktionen der Oszilloskopmodelle. Auf den folgenden Seiten werden die neuen Funktionen des Modelle TDS 600C beschrieben.
Table 1: Wichtige Funktionen und Modellvergleich
Funktion 520D 540D 580D 654C 680C 684C 724D 754D 784D 794D
Anzahl Kanäle 2+2 Digitalgeschwin-
digkeit, max. Anzahl Kanäle bei max.
Geschwindigkeit Analoge Bandbreite 500 MHz 1GHz 500
Aufzeichnungslänge, max.
DPO-Erfassung Ja Nein Ja Hochauflösungs-
erfassung Erweiterte DSP Math Kommunikations-
signalanalyse Referenzempfänger Option 3C und 4C Nein Option 3C und 4C Nein
3
1
2 GS/s 4 GS/s 5 GS/s 2 GS/s 4 GS/s
1 2 1 4 2 4 1 2 1
4 4 4 2+2
MHz
Bis 50 K/Kanal
Option 2F Standard
Option 2C Nein Option 2C
2
Ja Nein Ja
Bis 15 K/Kanal Bis 50 K/Kanal
1
4 2+2
1GHz 500 MHz 1GHz 2GHz
1
4 4 4
2
4
TDS 500D, TDS 600C & TDS 700D Zusatz
1
Funktionen des Modelle TDS 600C
Table 1: Wichtige Funktionen und Modellvergleich (Forts.)
Funktion 794D784D754D724D684C680C654C580D540D520D
Speichern,
Diskette Festplatte Zip-Laufwerk
E/A mit RS–232 und Centronics
Eingangsimpedanz 50 W und1MW nur
5
Option 13 Standard
Standard
Option HD
Standard
4
50 W
Messungsstatistiken (Durchschnitt, min., max. und Std.abw.)
Signalhistogramme Standard Auf Java basierende
Anwendungen Anzeige Mono Farbe Mono Farbe
1
Mit dem Kanalbetrieb 2 + 2 können zwei von vier Kanälen gleichzeitig angezeigt werden. Nicht angezeigte Kanäle können zum Koppeln eines Triggersignals mit dem Oszilloskop verwendet werden.
2
Diese TDS-Modelle sind mit der Option 1M oder der Option 2M erhältlich, mit denen längere Aufzeichnungseinstellungen möglich sind (max. 2 MB/Kanal). Siehe Option 1M und Option 2M auf den Seiten 7 und 8.
3
Mit einer erweiterten digitalen Signalverarbeitung erhält man FFTs, Integrale und Ableitungen von Signalen. Siehe Option 2F auf Seite 8.
4
Standard bezeichnet eine Standard-Produktfunktion im Unterschied zu einer Funktion, die Teil einer Option ist.
5
GPIB E/A ist in allen Modellen enthalten.
Histogramme anzeigen
Das Modell TDS 600C kann die im Benutzerhandbuch TDS 500D, TDS 600B &
Standard
Verfügbar
TDS 700D Digitaloszilloskope beschriebenen Histogramme anzeigen.
Eine Anwendung
auswählen
Das Modell TDS 600C kann im Menü APPLICATION auf Java basierende Anwendungen laden, wie dies im TDS 500D-, TDS 600B- und TDS 700D-Digi- taloszilloskope Benutzerhandbuch beschrieben ist. Sie können die Anwendung dann über die APPLICATION-Menüs steuern.
2
TDS 500D, TDS 600C & TDS 700D
Zusatz
Funktionen des Modelle TDS 600C
Option HD
Unterstützung eines
Iomega Zip-Laufwerks
Messungsstatistiken
anzeigen
Optische Messungen
durchführen
Externe Abschwächung
Das Modell TDS 600C enthält eine optionale Festplatte, die Sie zum Speichern und Abrufen von Signalen, für Installationen und Hardcopies, wie im
TDS 500D-, TDS 600B- und TDS 700D-Digitaloszilloskope – Benutzerhandbuch
beschrieben, verwenden können. Mit dieser Option können Sie auch auf Java basierende Anwendungsprogramme ausführen.
Das Modell TDS 600C ist mit 100-MB-Zip-Laufwerken von Iomega, wie im
TDS 500D-, TDS 600B- und TDS 700D-Digitaloszilloskope – Benutzerhandbuch
beschrieben, kompatibel.
Das Modell TDS 600C kann Statistiken über eine Messung, wie im TDS 500D-, TDS 600B- und TDS 700D-Digitaloszilloskope Benutzerhandbuch beschriebe n, -­anzeigen.
Mit dem Modell TDS 600C können das Belichtungsverhältnis, der Belichtungs- anteil, die Belichtungs-dB und Durchschnitts-dBm, wie im TDS 500D-, TDS 600B- und TDS 700D-Digitaloszilloskope Benutzerhandbuch beschrieben, gemessen werden.
Beim TDS 600C kann die externe Abschwächung, wie im Benutzerhandbuch für die Digitaloszilloskope TDS 500D, TDS 600B & TDS 700D beschrieben, eingestellt werden.
Tastkopfkalibrierung
Verwenden Sie beim Modell TDS 600C dieselbe Vorgehensweise zur Kalibrier­ung eines Tastkopfs wie bei TDS 500D and TDS 700D. Die Vorgehensweise ist im Benutzerhandbuch für die Digitaloszilloskope TDS 500D, TDS 600B & TDS 700D beschrieben.
TDS 500D, TDS 600C & TDS 700D Zusatz
3
Funktionen des Modelle TDS 600C

Optionen

Tektronix liefert die in der Tabelle beschriebenen Optionen aus 2:
Table 2: Optionen
Option # Bezeichnung Beschreibung
A1 Universal-Netzkabel für
Europa A2 Netzkabel fürGroßbritannien Netzkabel mit 240 V, 50 Hz A3 Netzkabel für Australien Netzkabel mit 240 V, 50 Hz A4 Netzkabel für Nordamerika Netzkabel mit 240 V, 60 Hz A5 Netzkabel für die Schweiz Netzkabel mit 220 V, 50 Hz HD Festplattenlaufwerk Fügt Festplatte hinzu. 05 Videotriggerung Das Oszilloskop wird mit Instrumenten zur Überprüfung von Ereignissen ausgeliefert, die
13 RS-232/Centronics Hardco-
py-
Schnittstellenanschlüsse 1G 1 GS/s maximal Beschränkt die Abtastrate auf max. 1 GS/s.
1K Oszilloskopwagen K420 Oszilloskopwagen. Mit diesem Wagen können Sie das Oszilloskop in jeder
1M 130.000 Aufzeichnungslänge Erhöht die Aufzeichnungslänge von standardmäßig 50.000 Abtastwerten wie folgt:
Netzkabel mit 220 V, 50 Hz
auftreten, wenn ein Video-Signal einen horizontalen oder vertikalen Synchronisationsim­puls erzeugt. Mit diesen Instrumenten können Sie eine Reihe von NTSC-, PAL-, SECAM­und hochaufgelöste TV-Signale überprüfen. (Diese Option steht beim Modell TDS 794D nicht zur Verfügung.)
Fügt RS-232-C- und Centronics-Schnittstellenanschlüsse hinzu. (Diese Option steht nur beim Modell TDS 500D zur Verfügung.)
(Diese Option steht nur bei den Modellen TDS 520D, TDS 540D, TDS 724D und TDS 754D zur Verfügung.)
beliebigen Laborumgebung transportieren.
Bei den Modellen TDS 520D und TDS 724D: Auf 250.000 Abtastwerte auf einem Kanal und 130.000 auf zwei Kanälen
Bei den Modellen TDS 540D, TDS 580D, TDS 754D, TDS 784D und TDS 794D: Auf
500.000 Abtastwerte auf einem Kanel, 250.000 auf zwei Kanälen und 130.000 auf drei bzw. vier Kanälen
(Diese Option steht nur bei den oben beschriebenen Modellen zur Verfügung.)
4
TDS 500D, TDS 600C & TDS 700D
Zusatz
Table 2: Optionen (Forts.)
Option # BeschreibungBezeichnung
Funktionen des Modelle TDS 600C
2M
1R Gestelleinbau Das Oszilloskop wird zur Installation in einem 19 Zoll (48 cm) breiten Gestell geliefert.
2C
3C P6701B mit Systemkalibrier-
4C P6703B mit Systemkalibrier-
31 Gepufferter passiver Tastkopf Fügt einen gepufferten passiven P6339A 10x-Tastkopf mit 500 MHz hinzu
32 Aktiver Tastkopf Fügt einen aktiven P6217-Tastkopf mit 4 GHz hinzu
33 Tastkopf mit niedriger Kapa-
34 Differenztastkopf Fügt einen 1-GHz (nur Tastkopf) P6247 Differenztastkopf hinzu 35 Aktiver Tastkopf Fügt einen aktiven P6243-Tastkopf mit 1 GHz (nur Tastkopf) hinzu
36 Passiver Tastkopf Fügt einen passiven P6139A 10X-Tastkopf 500-MHz hinzu
37 Aktiver Tastkopf Fügt einen aktiven P6245-Tastkopf mit 1,5 GHz hinzu
2F
8 M Erfassungslänge
Kommunikations­signalanalyse
ung
ung
zität
Erweitertes DSP Math
Erweitert die standardmäßige Erfassungslänge wie folgt:
Bei den Modellen TDS 520D und TDS 724D: Auf 2 M Abtastwerte auf zwei Kanälen und 4 M auf einem Kanal
Bei den Modellen TDS 540D, TDS 580D, TDS 754D, TDS 784D und TDS 794D: Auf 2 M Abtastwerte auf drei bzw. vier Kanälen, 4 M auf zwei Kanälenund8MAbtastwerteauf einem Kanal
(Diese Option umfaßt eine Festplatte und steht nur bei den oben beschriebenen Modellen zur Verfügung.)
Wenn Sie später umrüsten möchten, bestellen Sie den Umrüstsatz Nr. 016-1236-00. Das Oszilloskop ist zur Kommunikationssignaltriggerung und zum Testen von Toleranz-
masken konfiguriert. (Diese Option steht nur bei den Modellen TDS 500D und TDS 700D zur Verfügung.)
Das Oszilloskop wird mit einem P6701B- und einem optischen kalibrierten Kurzwellen-Re­ferenzempfänger auf Kanal 1 ausgeliefert. (Diese Option steht nur bei den Modellen TDS 500D und TDS 700D zur Verfügung, außer beim Modell TDS 794D.)
Das Oszilloskop wird mit einem P6701B- und einem optischen kalibrierten Langwellen­Referenzempfänger auf Kanal 1 ausgeliefert. (Diese Option steht nur bei den Modellen TDS 500D und TDS 700D zur Verfügung, außer beim Modell TDS 794D.)
(Diese Option steht nur beim Modell TDS 794D zur Verfügung.)
(Diese Option steht nur beim Modell TDS 794D zur Verfügung.) Fügt einen P6158 20x-Tastkopf niedriger Kapazität mit 3,0 GHz (nur Tastkopf) und 1 k
hinzu (Diese Option steht nur bei den Modellen TDS 580D, TDS 680C, TDS 684C, TDS 784D und TDS 794D zur Verfügung.)
(Diese Option steht nur bei den Modellen TDS 754D, TDS 724D, TDS 540D und TDS 520D zur Verfügung.)
(Diese Option steht nur bei den Modellen TDS 784D, TDS 600C und TDS 580D zur Verfügung.)
(Diese Option steht nur bei den Modellen TDS 794D, TDS 784D, TDS 680C, TDS 684C und TDS 580D zur Verfügung.)
Fügt erweiterte DSP Math-Funktionen wie FFT, Integration und Differenzierung hinzu. (Diese Option steht nur bei den Modellen TDS 500D zur Verfügung.)
TDS 500D, TDS 600C & TDS 700D Zusatz
5
Funktionen des Modelle TDS 600C
Table 2: Optionen (Forts.)
Option # BeschreibungBezeichnung
C3 Drei Jahre Kalibrierung Garantiert drei Jahre Kalibrierung C5 Fünf Jahre Kalibrierung Garantiert fünf Jahre Kalibrierung D1 Kalibrierungsdatenbericht Das Oszilloskop wird mit einem Kalibrierungsdatenbericht ausgeliefert. D3 Kalibrierungsdaten fürC3 Stellt Kalibrierungsdaten fürOptionC3zurVerfügung D5 Kalibrierungsdaten fürC5 Stellt Kalibrierungsdaten fürOptionC5zurVerfügung R5 Erweiterte Garantie Das Oszilloskop wird mit einer erweiterten Garantie von 5 Jahren geliefert. L1
Handbücher in französischer
Sprache
Stellt entsprechend der gewählten Optionsnummer verschiedene Sprachversionen des Benutzerhandbuchs zur Verfügung.
L3
L5
L9
Handbücher in deutscher
Sprache
Handbücher in japanischer
Sprache
Handbücher in koreanischer
Sprache

Standardzubehör

Das Oszilloskop wird standardmäßig mit dem in der Tabe lle 3 aufgeführten Zubehör geliefert.
Table 3: Standardzubehör
Zubehör Teilenummer
Benutzerhandbuch mit Programmier-Hilfsdiskette 071-0130-XX Referenzhandbuch 020-2313-XX Technische Referenz: Prüfung der Leistungsfähigkeit und Spezifikationen 071-0630-XX Tastköpfe:
TDS 754D und TDS 540D:
Vier passive P6139A 10X-Tastköpfe, 500 MHz TDS 654C: Vier aktive P6243-Tastköpfe, 1 GHz TDS 724D und TDS 520D:
Zwei passive P6139A 10X-Tastköpf e, 500 MHz TDS 794D, TDS 784D, TDS 684C, TDS 680C, TDS 580D:
Standardmäßig keine Tastköpfe
Frontschutzdeckel 200-3696-01
6
TDS 500D, TDS 600C & TDS 700D
P6139A P6243
P6139A
Zusatz

Optionales Zubehör

Funktionen des Modelle TDS 600C
Table 3: Standardzubehör (Forts.)
Zubehör Teilenummer
Zusatztasche (TDS 654C, TDS 684C, TDS 700D) 016-1268-00 Amerikansiches Netzkabel 161-0230-01
Sie können auch die in der Tabelle 4 aufgeführten optionalen Zubehörteile bestellen.
Table 4: Optionales Zubehör
Zubehör Teilenummer
Service-Handbuch 071-0627-XX Oszilloskopwagen K420 Gestelleinbausatz (zum Umrüsten) 016-1236-00 Zusatztasche (TDS 500D und TDS 680C) 016-1268-00 Tragetasche 016-0909-01 Transporttasche 016-1135-00 GPIB-Kabel (1 Meter lang) 012-0991-01 GPIB-Kabel (2 Meter lang) 012-0991-00 Centronics-Kabel 012-1214-00 RS-232-Kabel 012-1298-00
TDS 500D, TDS 600C & TDS 700D Zusatz
7
Funktionen des Modelle TDS 600C
Zusätzliche Tastköpfe
Die nachfolgende Tabelle 5 enthält die empfohlenen Tastköpfe für die einzelnen Oszilloskope.
Table 5: Empfohlene Tastköpfe –Übersicht
Tastkopf 520D
540D
Passiv
1X 10X P6139A P6139A P6139A P6139A P6139A P6139A P6339A 100X P5100 P5100 P5100 P5100 P5100 P5100
1000X P6015A P6015A P6015A P6015A P6015A P6015A SMD P6563A P6563A P6563A P6563A P6563A P6563A Niedrige Kapazität P6158 P6158 P6158 P6158 Aktiv CMOS/TTL P6243 P6245 P6243 P6245 P6243 P6245 P6245 Aktiv, Hohe Bandbreite P6245
Logisch P6408 P6408 P6408 P6408 P6408 P6408 Differential-Digital/
Telecom
P6101B P6101B P6101B P6101B P6101B P6101B
P6246,
P6247
580D 654C 680C
684C
P6245
P6217
P6247 P6246,
P6247
P6217
P6247 P6246,
724D 754D
P6247
784D 794D
P6245 P6217
P6247 P6247
P6245 P6217
Mikro-Volt ADA400A ADA400A ADA400A ADA400A ADA400A ADA400A Hochspannung P5205
P5210
Nur Wechselstrom P6021
P6022
CT-1 CT-2
Wechsel-/Gleichstrom TCP202
AM503S
Elektro-optischer Wan­dler
P6701B P6703B
P5205 P5210
P6021 P6022
CT-1 CT-2
TCP202
AM503S
P6701B P6703B
P5205 P5210
P6021 P6022
CT-1 CT-2
TCP202
AM503S
P6701B P6703B
P5205 P5210
P6021 P6022
CT-1 CT-2
TCP202
AM503S
P6701B P6703B
P5205 P5210
P6021 P6022
CT-1 CT-2
TCP202
AM503S
P6701B P6703B
P5205 P5210
P6021 P6022
CT-1 CT-2
TCP202
AM503S
P6701B P6703B
CT-1 CT-2
TCP202
AM503S
P6701B P6703B
8
TDS 500D, TDS 600C & TDS 700D
Zusatz
071-0273-03
6
6
6
TDS 520D, , TDS 724D
5
6
TDS 794D,
6
020-2313--XX
071-0630--XX
6
071-0627--XX
6
6
補足資料
TDS 500D, TDS 600C & TDS 700Dシリーズ デジタル・オシロスコープ
071-0273-03
このマニュアルは、ファームウェア Ver 5.1 以降の製品に対応しています。
Copyright © Tektronix, Inc. All rights reserved.
当社の製品は、米国その他各国における登録特許および出願中特許の対象となっています。本書の内容は、すで に発行されている他の資料の内容に代わるものです。また製品仕様は、予告なく変更する場合がありますので、 予めご了承ください。
Printed in the U.S.A.
Tektronix, Inc., P.O. Box 500, Beaverton, OR 97077
TEKTRONIXTEK Tektronix, Inc.の登録商標です。
TDS 600C シリーズの機能について
TDS 500 D/ TDS 600B/ TDS700 D シリーズ デジタル・オシロスコープのユーザ・マ ニュアルに記載されている TDS 600B シリーズに関する説明は、TDS 654C 型、TDS 680C 型、および TDS 684C 型にも適用できます。この補足資料では、TDS 600C シ リーズと TDS 600B シリーズの相違点について説明します。
主要機能
TDS 600C シリーズと TDS 600B シリーズの機能の違いは、この補足資料に記されて います。その他の機能はまったく同じですので、お手持ちのユーザ・マニュアル(そ の他のマニュアル類)で説明されている内容のほとんどは、TDS 600C シリーズに も適用できます。
オシロスコープの機種ごとの主要機能を表 1 に示します。表に引き続いて、TDS 600C シリーズの新しい機能を説明します。
1: 機種別主要機能一覧表
機能 520D型 540D型 580D型 654C型 680C型 684C型 724D型 754D型 784D型 794D型
入力チャンネル数 2+2
最高サンプル・レート 2 GS/s 4 GS/s 5 GS/s 2 GS/s 4 GS/s 最高サンプル・レート
で使用できるチャンネ ル数
アナログ周波数帯域 500 MHz 1 GHz 500MHz 1 GHz 500 MHz 1 GHz 2 GHz 最大レコード長 50K/チャンネル
アクイジション あり なし あり
DPO
アクイジション あり なし あり
Hi Res
演算機能
DSP
コミュニケーション・ シグナル・アナライザ
リファレンス・ レシーバ
3
1
1 2 1 4 2 4 1 2 1
オプション 2F 標準
オプション 2C 型 なし オプション 2C 型
オプション 3C および
オプション 4C 型
4 4 4 2+2
2
15K/チャンネル 50K/チャンネル
1
なし オプション 3C および
4 2+2
1
オプション 4C 型
4 4 4
4
2
なし
TDS 500D, TDS 600C & TDS 700D シリーズ 補足資料
1
TDS 600C
シリーズの機能について
1: 機種別主要機能一覧表(続き)
機能 794D型784D型754D型724D型684C型680C型654C型580D型540D型520D型
ストレージ機能
フロッピ・ディスク ハード・ディスク
ドライブ・
Zip
サポート
RS-232 tronics
ポート
入力インピーダンス
統計測定(平均、 最小、最大、および 標準偏差
ヒストグラム表示 標準
Java
ディスプレイ モノクロ カラー モノク
および
Cen-
を含んだ
5
I/O
)
アプリケーショ
オプション 13 標準
50  および 1M 50
標準
オプション HD型
標準
標準
利用可
4
のみ
カラー
1
2+2チャンネルでは、同時に表示できるチャンネル数は 2 チャンネルまでであることを意味します。ただし、残りの 2 チャンネルは、トリガ・チャンネルとして使用できます。
2
オプション 1M 型またはオプション 2M 型を装備すると、最大で 2M/チャンネルまで拡張できます。オプション 1M 型/ オプション 2M 型の詳細は、4 ページと 5 ページを参照してください。
3
DSP演算機能では、FFT、微分、積分を実行できます。
4
オプション指定なしでも装備されていることを示します。
5
GPIB ポートはすべての機種に標準で装備されています。
ヒストグラム表示
TDS 600C シリーズは、TDS 500 D/ 600B/ 700 D シリーズ ユーザ・マニュアルで説 明されているヒストグラム表示を実行できます。
アプリケーションを
選択する
TDS 600C シリーズは、TDS 500 D/ 600B/ 700 D シリーズ ユーザ・マニュアルで説 明されている Java アプリケーションを選択、ロードできます。アプリケーション は、APPLICATION メニューから操作します。
2
TDS 500D, TDS 600C & TDS 700D シリーズ 補足資料
TDS 600C
シリーズの機能について
オプション HD
Iomega Zip ドライブ
サポート
波形統計測定
光測定
外部アッテネータ
TDS 600C シリーズがオプションのハード・ディスクを装備している場合は、TDS 500 D/ 600B/ 700 D シリーズ ユーザ・マニュアルで説明されているように、波形、
設定、およびハードコピー・データの保存、呼出が行えます。さらに、Java アプリ ケーションを実行することもできます。
TDS 600C シリーズは、TDS 500 D/ 600B/ 700 D シリーズ ユーザ・マニュアルで説 明されているように、Iomega100 MB Zip ドライブと互換性があります。
TDS 600C シリーズは、TDS 500 D/ 600B/ 700 D シリーズ ユーザ・マニュアルで説 明されているように、波形の統計測定を実行できます。
TDS 600C シリーズは、TDS 500 D/ 600B/ 700 D シリーズ ユーザ・マニュアルで説
明されているように、消光比、消光比(%)、消光比(dB)、消光比(dBm)、および平均
dBm測定が行えます。
TDS 600C シリーズは、TDS 500 D/ 600B/ 700 D シリーズ ユーザ・マニュアルで説
明されているように、外部アッテネータが使用できます。
プローブ補正
TDS 600C シリーズのプローブ補正は、TDS 500 D/ 600B/ 700 D シリーズ ユーザ・ マニュアルで説明されている TDS 500Dシリーズおよび TDS 700Dシリーズの手順と 同様です。
TDS 500D, TDS 600C & TDS 700D シリーズ 補足資料
3
TDS 600C
シリーズの機能について
オプション
2: オプション
オプション 型名
A1
名称 内容
電源ケーブル
工場出荷時に注文可能なオプションを表 2 に示します。
220 V, 50 Hz ヨーロッパ用
A2
A3
A4
A5
HD
05
13 RS-232/Centronics
1G 1Gサンプル・レート
1K
1M
電源ケーブル
電源ケーブル
電源ケーブル
電源ケーブル
ハードディスク・ ドライブ
ビデオ・トリガ ビデオ信号の水平/垂直同期信号にトリガする機能です。NTSCPAL、SECAMおよ
インタフェース
台車
レコード長拡張
(130 K)
240 V, 50 Hz イギリス用
240 V, 50 Hz オーストラリア用
240 V, 60 Hz 北アメリカ用
220 V, 50 Hz スイス用
ハードディスク追加
HDTVに対応します。(TDS 794D 型を除く)
RS-232-C および Centronics インタフェース追加。 ( TDS 500D シリーズのみ)
サンプル・レートを最高 1 GS/s に制限します。 ( TDS 520D 型、TDS 540D 型、TDS 724D 型、および TDS 754D 型のみ)
K420 型台車
TDS 520D 型およびTDS 724D 型: 1 チャンネルで250,000ポイント、2チャンネルで130,000ポイント
TDS 540D 型、TDS 580D 型、TDS 754D 型、TDS 784D 型、および TDS 794D 型: 1 チャンネルで 500,000 ポイント、2チャンネルで250,000ポイント、 3 または 4 チャンネルで130,000ポイント
(本オプションは、ここで示されている機種のみに適用されます。)
4
TDS 500D, TDS 600C & TDS 700D シリーズ 補足資料
2: オプション(続き)
オプション 型名
2M
1R
2C
3C
4C SDH/SONET リファレ
31
32
33
34
レコード長拡張 (8M)
ラックマウント仕様 標準の19インチ・ラック用のラックマウント仕様
コミュニケーション・ シグナル・アナライザ
ファイバ・チャンネル リファレンス・ レシーバ
ンス・レシーバ
プローブ追加
プローブ追加
プローブ追加
プローブ追加
TDS 600C
シリーズの機能について
内容名称
TDS 520D 型およびTDS 724D 型: 1 チャンネルで4Mポイント、2チャンネルで2Mポイント
TDS 540D 型、TDS 580D 型、TDS 754D 型、TDS 784D 型、および TDS 794D 型: 1 チャンネルで 8Mポイント、2チャンネルで4Mポイント、 3 または 4 チャンネルで2Mポイント
(本オプションは、ここで示されている機種のみに適用されます。)
フィールド変換キットは部品番号 016-1236-00
コミュニケーション・シグナル・トリガ機能およびマスク・テスト機能が装備されま す。( TDS 500D および TDS 700D シリーズのみ)
P6701B 型 O/E 変換器に短波長光リファレンス・レシーバが付属します。 ( TDS 500D および TDS 700D シリーズ のみ、ただし TDS 794D 型を除く)
P6703B 型 O/E 変換器に長波長光リファレンス・レシーバが付属します。 ( TDS 500D および TDS 700D シリーズ のみ、ただし TDS 794D 型を除く)
P6339A 型 1 本追加 (TDS 794D 型のみ)
P6217 型 1 本追加 (TDS 794D 型のみ)
P6158 型 1 本追加 (TDS 580D 型、TDS 680C 型、TDS 684C 型、TDS 784D 型、およびTDS 794D 型のみ)
P6247 型 1 本追加
35
36
37
2F
プローブ追加
プローブ追加
プローブ追加
拡張演算機能
P6243 型 1 本追加 (TDS 754D 型、TDS 724D 型、TDS 540D 型、およびTDS 520D 型のみ)
P6139A 型 1 本追加 (TDS 784D 型、TDS 600C シリーズ、およびTDS 580D 型のみ)
P6245 型 1 本追加 (TDS 794D 型、TDS 784D 型、TDS 680C 型、TDS 684C 型、およびTDS 580D 型のみ)
FFT、微分、積分演算機能 ( TDS 500D シリーズでのみ有効)
TDS 500D, TDS 600C & TDS 700D シリーズ 補足資料
5
TDS 600C
シリーズの機能について
2: オプション(続き)
オプション 型名
C3 3 年校正
C5 5 年校正
D1
D3
D5
R5
L1
英文試験成績書
英文試験成績書 オプション C3 型の校正時に試験成績書を添付
英文試験成績書 オプション C5 型の校正時に試験成績書を添付
保証期間延長 保証期間が 5 年間に延長されます。
フランス語マニュアル
内容名称
ユーザ・マニュアルとクイック・リファレンス
L3
L5
L9
上記オプションの一部は、Tektronix 社からのみ購入可能です。詳しくは当社までお問い合わせください。
ドイツ語マニュアル
日本語マニュアル
朝鮮語(ハングル) マニュアル
スタンダード・アクセサリ
標準で付属しているアクセサリは表 3 のとおりです。
3: スタンダード・アクセサリ
アクセサリ
ユーザ・マニュアル(日本語)
クイック・リファレンス(日本語を含む各国言語セット)
Technical Reference: Performance Verification and Specifications
(英語)
プローブ:
TDS 754D 型および TDS 540D :
P6139A 500 MHz 受動プローブ 4 TDS 654C : P6243 1 GHz FFTプローブ 4 TDS 724D 型および TDS 520D :
P6139A 500 MHz 受動プローブ 2 TDS 794D 型、TDS 784D 型、TDS 684C 型、 TDS 680C 型、TDS 580D :
プローブなし
部品番号
071-0134-XX
020-2313-XX
071-0630-XX
P6139A P6243
P6139A
前面カバー
6
TDS 500D, TDS 600C & TDS 700D シリーズ 補足資料
200-3696-01
TDS 600C
3: スタンダード・アクセサリ(続き)
アクセサリ 部品番号
アクセサリ・ポーチ (TDS 654C 型、TDS 684C 型、TDS 700D シリーズのみ)
シリーズの機能について
016-1268-00
電源ケーブル
オプショナル・アクセサリ
注文可能なオプショナル・アクセサリは表 4 のとおりです。
4: オプショナル・アクセサリ
アクセサリ
サービス・マニュアル
オシロスコープ用台車
ラックマウント・キット (フィールド変換キット)
アクセサリ・ポーチ (TDS 500D シリーズおよび TDS 680C 型)
ソフト・キャリング・ケース
トランジット・ケース
GPIB ケーブル (1 m) 012-0991-01
GPIB ケーブル (2 m) 012-0991-00
161-0230-01
部品番号
071-0627-XX
K420
016-1236-00
016-1268-00
016-0909-01
016-1135-00
Centronics ケーブル 012-1214-00
RS-232 ケーブル 012-1298-00
TDS 500D, TDS 600C & TDS 700D シリーズ 補足資料
7
TDS 600C
シリーズの機能について
アクセサリ・プローブ
各オシロスコープに対応する推奨プローブを表 5 に示します。
5: 推奨プローブ一覧
プローブ TDS520D/
TDS540D
受動プローブ
1 × 10 × P6139A P6139A P6139A P6139A P6139A P6139A P6339A
100 × P5100 P5100 P5100 P5100 P5100 P5100
1000 × P6015A P6015A P6015A P6015A P6015A P6015A
SMD 表面実装用
低容量 P6158 P6158 P6158 P6158
CMOS/TTL
広帯域 FFT プローブ P6245
ロジック・プローブ P6408 P6408 P6408 P6408 P6408 P6408
差動プローブ/ テレコム用
増幅器 ADA400A ADA400A ADA400A ADA400A ADA400A ADA400A
高電圧プローブ P5205
電流プローブ (AC のみ)
電流プローブ (AC/DC
O/E 変換器
P6101B P6101B
P6563A P6563A P6563A P6563A P6563A P6563A
P6243 P6245 P6243 P6245 P6243 P6245 P6245
P6246,
P6247
P5210
P6021 P6022
CT-1 CT-2
TCP202
AM503S
P6701B P6703B
TDS580DTDS654C TDS680C/
TDS684C
P6101B
P6217
P6247 P6246 型,
P6247
P5205 P5210
P6021 P6022
CT-1 CT-2
TCP202 AM503S
P6701B P6703B
P5205 P5210
P6021 P6022
CT-1 CT-2
TCP202
AM503S
P6701B P6703B
P6101B P6101B P6101B
P6245 P6217
P6247 P6246 型,
P5205 P5210
P6021 P6022
CT-1 CT-2
TCP202
AM503S
P6701B P6703B
TDS724D/
TDS754D
P6247
P5205 P5210
P6021 P6022
CT-1 CT-2
TCP202 AM503S
P6701B P6703B
TDS784DTDS794D
P6245 P6217
P6247 P6247
P5205 P5210
P6021 P6022
CT-1 CT-2
TCP202
AM503S
P6701B P6703B
P6245 P6217
CT-1 CT-2
TCP202
AM503S
P6701B P6703B
8
TDS 500D, TDS 600C & TDS 700D シリーズ 補足資料
Loading...