Tektronix TDS6UP, TDS7UP,,CSA7UP Option CPU Upgrade Kit Field Install Instructions
Instructions
TDS6UP, TDS7UP, and CSA7UP Option CPU
Upgrade Kit
071-1244-01
Warning
The servicing instructions are for use by qualified
personnel only. To avoid personal injury, do not
perform any servicing unless you are qualified to
do so. Refer to all safety summaries prior to
performing service.
www.tektronix.com
*P071124401*
071124401
Copyright © Tektronix, Inc. All rights reserved.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes
that in all previously published material. Specifications and price change privileges reserved.
Tektronix, Inc., P.O. Box 500, Beaverton, OR 97077
TEKTRONIX and TEK are registered tradem arks of Tektronix, Inc.
Service Safety Summary
Only qualified personnel should perform service procedures. Read this Service
Safety Summary and the General Safety Summary in the product service manual
or the instruction manual.
Do Not Service Alone. Do not perform internal service or adjustments of this
product unless another person capable of rendering first aid and resuscitation is
present.
Disconnect Power. To avoid electric shock, switch off the instrument power, then
disconnect the power cord from the mains power.
Use Care When Servicing With Power On. Dangerous voltages or currents may
exist in this product. Disconnect power, remove battery (if applicable), and
disconnect test leads before removing protective panels, soldering, or replacing
components.
To avoid electric shock, do not touch exposed connections.
TDS6UP, TDS7UP, and CSA7UP Option CPU Upgrade Kit
1
Service Safety Summary
2
TDS6UP, TDS7UP, and CSA7UP Option CPU Upgrade Kit
Kit Description
This document supports upgrading the NLX CPU board and microprocessor. To
upgrade your NLX CPU board and microprocessor perform each of the
following procedures in order.
Products
TDS6000 Series All serial numbers
TDS7000 Series All serial numbers
CSA7000 Series All serial numbers
Minimum Tool and Equipment List
Table 1: Equipment list
Required tools and equipment Part number
Screwdriver handle 620-440
T-20 Torx tip 640-250
T-15 Torx tip 640-247
1
/
inch flat-bladed screwdriver
8
#0 Phillips screwdriver Standard tool
3
/
inch open-end wrench
16
Standard tool
Standard tool
TDS6UP, TDS7UP, and CSA7UP Option CPU Upgrade Kit
3
Kit Description
Kit Parts List
Circuit/figure
number
1 1ea 650--4562--00 COMPONENT KIT;MOTHERBOARD/
2 1ea 407--4880--01 BRACKET; CD--ROM, REAR DRIVE BAY
1
Quantity Part number Description
MICROPROCESSOR UPGRADE;TDS6/7UP
OPTION CPU
CHASSIS, 0.035 CRS
1ea 020--2349--XX SOFTWARE KIT; LICENSE CERTIFICATE,O/S
EASY RESTORE,CERTIFICATE AUTHENTICITY,WIN98 RESTORE CD
1ea 063-3645-01 SOFTWARE; BIOS UPDATE CD
Figure 1: CPU upgrade kit parts
2
4
TDS6UP, TDS7UP, and CSA7UP Option CPU Upgrade Kit
Installation Instructions
This section contains all procedures needed to install TDS6UP, TDS7UP, or
CSA7UP Option CPU in the TDS6000, TDS7000, and CSA7000 Series
instruments.
These instructions are for personnel who are familiar with servicing the product.
If you need further details for disassembling or reassembling the product, refer to
the appropriate product manual. Contact your nearest Tektronix Service Center
or Tektronix Factory Service for installation assistance.
CAUTION. To prevent static discharge damage, service the product only in a
static-free environment. Observe standard handling precautions for static-sensitive devices while installing this kit. Always wear a grounded wrist strap,
grounded foot strap, and static resistant apparel while installing this kit.
Remove
Preparation
This section contains procedures for removal and installation of all mechanical
and electrical modules.
H Line Cord
H Trim (all)
H Bottom cover
H Left and Right covers
H NLX board
H Rear chassis
H CD drive bracket
WARNING. Before doing this or any other procedure in this manual, read the
Safety Summary found at the beginning of this manual.
TDS6UP, TDS7UP, and CSA7UP Option CPU Upgrade Kit
5
Loading...