Tektronix TDS5054B, TDS5104B, TDS5032B, TDS5052B, TDS5054BE Combined User/Service

...
xx
050-3672-03 and Above Hard Drive Replacement for TLA5000 Series Logic Analyzer
ZZZ
TDS5000B Series Digital Phosphor Oscilloscope
Instructions
www.tektronix.com
P075087102*
075-0871-02
Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all previously published material. Specications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc. 14200 SW Karl Braun Drive P.O. B o x 5 0 0 Beaverto USA
For product information, sales, service, and technical support:
n, OR 97077
In North America, call 1 -800-833-9200. Worl dwid e, vis it www.tektronix.com to nd contacts in your area.
Service Safety Summary
Only qualied personnel should perform service procedures. Read the Service Safety Summary and the General Safety Summary located in the service manual
before perfo
Do Not Service Alone. Do not perform internal service o r adjustments of this product unless another person capable of rendering rst aid and resuscitation is present.
rming any service procedures.
Disconnec
disconnect the power cord from the mains power.
UseCareWhenServicingWithPowerOn. Dangerousvoltagesorcurrentsmay exist in this product. Disconnect power, remove battery (if applicable), and disconnect test leads before removing protective panels, soldering, or replacing compon
To avoid electric shock, do not touch exposed connections.
tPower. To avoid electric shock, switch off the instrument power, then
ents.
Hard Disk Replacement Kit for TLA5000, TDS5000B, and VM5000 1
Kit Description
Kit Description
Products
This kit contains parts necessary to replace the 119-7151-XX hard drive with the 119-7484-XX hard drive. The 119-7484-XX hard drive requires that you also run the 063-3844
-XX disk to ensure proper mode settings. You also need to run the
020-2865-XX CD to set up the touch screen display.
Kit Parts List
TLA5000B
TDS5000B Series SN B019999 and Below
Quantity Part number Description
1 ea 119-7484-XX Disk Drive, Winchester, 3.5 inch, ATA
1 ea 063-3844-02 Hitachi V2.13 Feature Tool Disk
1 ea 020-2989-XX
1 ea 075-0871-02 Instructions, 050-3672-XX Hard Drive
1
The software installation procedure is provided in the CD booklet (071 -2207-XX).
SN B019999 and Below
1
Accessory kit; Software CD, Touch Screen Switcher Tool V.1.0.0
Replacement
2 Hard Disk Replacement Kit for TLA5000, TDS5000B, and VM5000
Installation Instructions
Install
1. Install the new hard drive.
2. Power on the instrument.
3. Insert the Hitachi Feature Tool V2.13 disk into the disk drive.
4. Boot to the disk.
Installation Instructions
5. From the me
a. Select Ultra DMA mode 5.
b. Click Ok.
6. Power off the instrument.
7. Remove the Hitachi Feature Tool V2.13 CD when nished.
8. At Insert Boot Media prompt, insert the Operating Restore CD for your
instrument and then press any key to reboot.
9. Install the Touch Screen Switcher Tool using the instructions in the CD booklet.
10. Install any necessary product application software.
End of Document.
nu bar, select Features > Change Ultra DMA Mode.
Hard Disk Replacement Kit for TLA5000, TDS5000B, and VM5000 3
Loading...