Instructions
TDSXFHD
Hard Disk Upgrade
TDS 500C/D, TDS 600C & TDS 700C/D/L
Digitizing Oscilloscopes
071-0442-02
Warning
The servicing instructions are for use by qualified
personnel only. To avoid personal injury, do not
perform any servicing unless you are qualified to
do so. Refer to all safety summaries prior to
performing service.
*P071044202*
071044202
Copyright © T ektronix, Inc. All rights reserved.
T ektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes
that in all previously published material. Specifications and price change privileges reserved.
Printed in the U.S.A.
T ektronix, Inc., P.O. Box 1000, Wilsonville, OR 97070–1000
TEKTRONIX and TEK are registered trademarks of T ektronix, Inc.
WARRANTY
T ektronix warrants that the parts, assemblies and supplies (“products”) that it manufactures and sells will be free
from defects in materials and workmanship for a period of three (3) months from the date of shipment. If a
product proves defective during this warranty period, T ektronix, at its option, either will repair the defective
product without charge for parts and labor, or will provide a replacement in exchange for the defective product.
In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration
of the warranty period and make suitable arrangements for the performance of service. Customer shall be
responsible for packaging and shipping the defective product to the service center designated by T ektronix, with
shipping charges prepaid. Tektronix shall pay for the return of the product to Customer if the shipment is to a
location within the country in which the T ektronix service center is located. Customer shall be responsible for
paying all shipping charges, duties, taxes, and any other charges for products returned to any other locations.
This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate
maintenance and care. T ektronix shall not be obligated to furnish service under this warranty a) to repair damage
resulting from attempts by personnel other than T ektronix representatives to install, repair or service the product;
b) to repair damage resulting from improper use or connection to incompatible equipment; c) to repair any
damage or malfunction caused by the use of non-T ektronix supplies; or d) to service a product that has been
modified or integrated with other products when the effect of such modification or integration increases the time
or difficulty of servicing the product.
THIS WARRANTY IS GIVEN BY TEKTRONIX IN LIEU OF ANY OTHER WARRANTIES, EXPRESS
OR IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TEKTRONIX’
RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND
EXCLUSIVE REMEDY PROVIDED TO THE CUST OMER FOR BREACH OF THIS WARRANTY.
TEKTRONIX AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT , SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR
THE VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.
Service Safety Summary
Only qualified personnel should perform service procedures. Read this Service
Safety Summary and the General Safety Summary before performing any service
procedures.
Do Not Service Alone. Do not perform internal service or adjustments of this
product unless another person capable of rendering first aid and resuscitation is
present.
Disconnect Power. To avoid electric shock, switch off the instrument power, then
disconnect the power cord from the mains power.
Use Caution When Servicing the CRT. To avoid electric shock or injury, use
extreme caution when handling the CRT. Only qualified personnel familiar with
CRT servicing procedures and precautions should remove or install the CRT.
CRTs retain hazardous voltages for long periods of time after power is turned off.
Before attempting any servicing, discharge the CRT by shorting the anode to
chassis ground. When discharging the CRT, connect the discharge path to ground
and then the anode. Rough handling may cause the CRT to implode. Do not nick
or scratch the glass or subject it to undue pressure when removing or installing it.
When handling the CRT, wear safety goggles and heavy gloves for protection.
Use Care When Servicing With Power On. Dangerous voltages or currents may
exist in this product. Disconnect power, remove battery (if applicable), and
disconnect test leads before removing protective panels, soldering, or replacing
components.
To avoid electric shock, do not touch exposed connections.
X-Radiation. To avoid x-radiation exposure, do not modify or otherwise alter the
high-voltage circuitry or the CRT enclosure. X-ray emissions generated within
this product have been sufficiently shielded.
Hard Disk Upgrade
Service Safety Summary
Hard Disk Upgrade
Kit Description
This document supports installing Option HD in the oscilloscopes listed below.
Products
TDS 520C/D All serial numbers
TDS 540C/D All serial numbers
TDS 580C/D All serial numbers
TDS 654C All serial numbers
TDS 680C All serial numbers
TDS 684C All serial numbers
TDS 694C All serial numbers
TDS 714L All serial numbers
TDS 724C/D All serial numbers
TDS 754C/D All serial numbers
TDS 784C/D All serial numbers
TDS 794D All serial numbers
Minimum Tool and Equipment List
Kit Parts List
Required tools and equipment Part number
Service manual:
TDS 500C, TDS 600B & TDS 700C
TDS 500D, TDS 600C, TDS 700D & TDS 714L
Firmware:
TDS 714L V6.6 or above
TDS 500D & TDS 700D V6.2.1 or above
TDS 500C & TDS 700C V5.3 or above
TDS 600C V5.0.1 or above
Quantity Part number
1 EA 679-4850-0 CKT BD ASSY:HARD DISK (OPTION HD)
1 EA 650-3972-03 HARD DRIVE,FORMATTED W Pull TAB 334-0575-00
1 EA 407-4697-00 RET AINER BRACKET,HARD DISK BD
1 EA 679-4095-00 CKT BD ASSY:OPTION CONNECT OR BD
1
Description
070-9875-03
071-0271-00, 071-0495-00, 071-0627-00,
or later
063-3087-06 or later
063-3087-02 or later
063-2770-02 or later
063-3131-00 or later
Hard Disk Upgrade
1
Kit Description
Quantity DescriptionPart number
1
4 EA 210-0457-00 NUT,PL,ASSY WA6 32X0.312,STL CD PL,W/LOCKWASHER
1 EA 071-0442-02 MANUAL,TECH;TDSXFHD
1 EA NS
1
Part numbers may vary due to part or circuit improvements.
2
NS – Not Saleable
2
Label
2
Hard Disk Upgrade
Installation Instructions
These instructions are for personnel who are familiar with servicing the product.
If you need further details for disassembling or reassembling the product, refer to
the appropriate product manual. Contact Tektronix Factory Service for installation assistance.
CAUTION. To prevent static discharge damage, service the product only in a
static-free environment. Observe standard handling precautions for static-sensitive devices while installing this kit. Always wear a grounded wrist strap,
grounded foot strap, and static resistant apparel while installing this kit.
These instructions are provided to assist you in installing option HD in your
oscilloscope. Refer to your oscilloscope service manual for detailed information.
Install
To install Option HD, perform the following steps:
1. If your oscilloscope contains Option 5, remove the Option 5 assembly as
described in the Removal and Installation Procedures in your service
manual.
2. Remove the CPU board using the A11 Processor/Display Board procedure in
your service manual.
3. Install the hard disk circuit board, supplied with this upgrade, using step 4 of
the Hard Disk Drive procedure in your service manual.
4. Install the hard disk supplied with this upgrade (use Figure 1 as a guide).
5. Reassemble the oscilloscope.
6. If the oscilloscope firmware is not the version or a newer version than that
listed in the Minimum Tool and Equipment List (see page 1), install the
firmware version or a newer version than that listed.
7. If you install firmware on an oscilloscope with option 3C or 4C, perform the
option 3C or 4C optical probe calibration.
8. Perform a signal path compensation.
9. Install the label supplied with this kit to the rear panel of the oscilloscope.
Hard Disk Upgrade
3
Installation Instructions
Pull Tab
Hard Disk
Bracket
Hard Disk Drive Board
Figure 1: Hard disk removal
Retainer Bracket
1
2
3
4
Hard Disk Upgrade
Verify Operation
Installation Instructions
Refer to the Performance Verification section in the service manual. Verify
oscilloscope performance by performing the Verify the File System procedure. If
you can successfully save and recall a waveform or a setup to the hard disk
(hd0:), installation was successful.
g End of document g
Hard Disk Upgrade
5
Loading...