xx
Software Upgrade for
RTX100B ISDB-T RF Signal Generator and
ZZZ
RTX130B QAM & VSB RF Signal Generator
Instructions
Warning
The servicing instructions are for use by qualified personnel
only. To avoid personal injury, do not perform any servicing
unless you are qualified to do so. Refer to all safety summaries
prior to performing service.
www.tektronix.com
P075093102*
*
075-0931-02
Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries
or suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication
supersedes that in all previously published material. Specifications and pric e change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14200 SW Karl Braun Drive
P.O . Bo x 50 0
Beaverto
USA
For product information, sales, service, and technical support:
n, OR 97077
In North America, call 1-800-833-9200.
World wide, v isit www.tektronix.com to find contacts in your area.
Kit Description
Products
Kit Parts List
This kit provides a document with your option authorization key and instructions
to upgrade your RTX100B ISDB-T RF Signal Generator or RTX130B QAM &
VSB RF Signal Generator to various software upgrade options. (See Table 2.)
RTX100B ISDB-T RF Signal Generator
RTX130B QAM & VSB RF Signal Generator
The following table lists the items that ship with the software field upgrades.
Table 1: Kit part list
y
Quantit
1ea
1 ea 063-4085-xx
1 ea 075-0931-02
1 ea 063-4114-xx
1
NS - Not Saleable
Part num
NS
ber
1
Descrip
DATA SH
USB FLA
MANUA
USER D
tion
EET; OPTION KEY INFORMATION
SH DRIVE
L, T E C H: INSTRUCTIONS, UPGRADE KIT
OC CD
RTX100B and RTX130B Software Upgrade Instructions 1
Installation Instructions
Installation Instructions
This section provides information on various software upgrade options and how
to enable them on your RTX100B ISDB-T RF Signal Generator or RTX130B
QAM & VSB RF Si
Software Upgrade Options
The following table lists the upgrade options which can be enabled on the
RTX100B and RTX130B instruments.
NOTE. To enable the UPG upgrade option refer to Software Upgrade Using the
USB Flash Drive. (See page 3.) To enable the other upgrade options refer to
Entering the O ption Key. (See page 6.)
Table 2: Software Upgrade Options
gnal Generator.
Option Description
RTX10UP: Field upgrade kit for RTX100B.
SC Upgrade to add the Scheduler option to RTX100B.
UPG Upgrade RTX100B to the latest software version.
RTX13UP: Field upgrade kit for RTX130B.
M1
M2 Upgrade to add ITU-T J.83 Annex B Modulation Mode to RTX130B.
M3
M4
SC Upgrade to add the Scheduler option to RTX130B.
UPG Upgrade RTX130B to the latest software version.
RTXPAUP: Field upgrade kit for RTX100B and RTX130B.
TSCA Upgrade to add Deferred Time Transport Stream Compliance Analyzer
MX
ES Upgrade to add ES Analyzer to RTX100B and RTX130B.
PA
BA
DB
CG Upgrade to add Carousel Generator to RTX100B and RTX130B.
DBCG Upgrade to add Carousel Analyzer and Carousel Generator to RTX100B
Upgrade to add DVB-C/ITU-T J.83 Annex A M odulation Mode to
RTX130B.
Upgrade to add ITU-T J.83 Annex C Modulation Mode to RTX130B.
Upgrade to add ATSC Modulation Mode to RTX130B.
to RTX100B and RTX130B. Upgrade to add Deferred Time Transport
Stream Compliance Analyzer to RTX100B or RTX130B.
Upgrade to add Deferred Time Multiplexer to RTX100B and RTX130B.
Upgrade to add PES Analyzer to RTX100B and RTX130B.
Upgrade to add Buffer Analyzer to RTX100B and RTX130B.
Upgrade to add Carousel Analyzer to RTX100B and RTX130B.
and RTX130B.
2 RTX100B and RTX130B Software Upgrade Instructions
Installation Instructions
Software Upgrade Using
the USB Flash Drive
Perform the fol
using the USB flash drive and the UPG option.
1. Connect the US
dialog box with various install options is displayed.
lowing steps to upgrade the software version from 9.X to 10.X
B flash drive to the USB connector of the instrument. A
2. Select Install Tektronix MPEG Application Suite and click OK.
Immediately, an InstallShield Wizard that allows you to install the application
played. Click Next to continue.
is dis
RTX100B and RTX130B Software Upgrade Instructions 3
Installation Instructions
3. Select MTX/RTX
4. Click Install to begin the installation process.
as the Setup type and click Next to continue.
During the progress, the following WinPcap 4.0.2 Setup message is displayed.
Click OK to continue.
4 RTX100B and RTX130B Software Upgrade Instructions
Installation Instructions
5. Choose the opti
down and restart.
6. After the restart, a Hardware Update Wizard dialog box is displayed. Choose
No, not this time option and click Next to proceed. Follow the on screen
ctions, and the wizard automatically installs the hardware driver.
instru
on to restart the PC, and then select Finish. The PC will shut
rform steps 3 through 7 listed in the Entering the Option Key section to
7. Pe
enter the UPG option key. (See page 6.)
RTX100B and RTX130B Software Upgrade Instructions 5
Installation Instructions
Entering the Option Key
Perform the fol
upgrade kit.
1. Connect a keyb
they are not already installed).
2. Power on the
3. Connect the dongle that is supplied with the instrument.
4. From the Start menu, select Programs > Tektronix MTS400 > Optionkey
Wizard to open the Tektronix Option Update dialog box.
lowing steps to enter the option key that is supplied w ith the
oard and mouse to the USB connectors of the instrument (if
instrument and wait for it to start.
Figure 1: Tektronix Option Update dialog box
5. Refer to the option key document that is supplied with the kit to identify the
option key numbers.
6. Enter the alphanumeric numbers in the Key String text box, and click the
Apply button.
The Tektronix Option Update dialog box is updated and the ordered option is
displayed along with the other options. If a wrong key string is entered, the
Key Status box displays the entered string as invalid.
6 RTX100B and RTX130B Software Upgrade Instructions
Installation Instructions
7. Apply the label
8. Restart the instrument to display the application screen.
End of document
of the ordered option to the right side of the cabinet.
RTX100B and RTX130B Software Upgrade Instructions 7
Loading...