xx
RSA6BUP Option WINXP Upgrade for
ZZZ
RSA6120B Series Real-Time Signal Analyzers
Instructions
www.tektronix.com
P071309800*
*
071-3098-00
Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries
or suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication
supersedes that in all previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14150 SW Karl Braun Drive
P.O. B o x 500
Beaverto
USA
For product information, sales, service, and technical support:
n, OR 97077
In North America, call 1-800-833-9200.
Worl dwid e, vis i t www.tektronix.com to find contacts in your area.
Table of Contents
Service safety summary............................................................................................ 1
Kit description ... .................................. ................................ ................................ . 2
Products.................................. ................................ ................................ ....... 2
Kit parts li
Overview ............................................................................................................ 3
Removing option 57 and option 59 installed drives . ................................ ........................... 4
Minimum tool and equipment list......................... ................................ ................... 4
Removing a DVD drive and internal hard drive (Option 57 or option 59) .............................. 4
Installing a new removable hard drive .. . ..... . ..... . ..... . ... . . ..... . ..... . ..... . .... . . .... . ..... . ..... . ..... ... 9
Install
Replacing an existing removable hard drive...................................... .............................. 11
Update the instrument BIOS ..................... .................................. .............................. 12
Installing the Windows Certificate of Authenticity label...................................................... 19
st.... ................................ .................................. ............................... 2
ing the Option WINXP removable hard disk drive ................ ................................ . 9
RSA6BUP Option WINXP Upgrade i
Table of Contents
ii RSA6BUP Option WINXP Upgrade
Service safety summary
Only qualified personnel should perform service procedures. Read this Service
Safety Summary and the General Safety Summary located in the RSA6100B
Real-Time Si
before performing any service procedures.
Do not service alone. Do not perform internal service or adjustments of this
product unless another person capable of rendering first aid and resuscitation is
present.
Disconnect power. To avoid electric shock, switch off the instrument power, then
disconnect the power cord from the mains power.
Use care when servicing with power on. Dangerous voltages or currents may exist
in this product. Disconnect power, remove battery (if applicable), and disconnect
ads before removing protective panels, soldering, or replacing components.
test le
To avoid electric shock, do not touch exposed connections.
gnal Analyzer Service manual (Tektronix part number 077-0648-XX)
RSA6BUP Option WINXP Upgrade 1
Kit description
Kit description
Products
Kit parts list
This kit describes the installation of Option WINXP in an RSA6120B Series
Real-Time Signal Analyzer.
RSA6120B. Allserialnumbers.
The following parts lists detail the parts included with your upgrade kit.
Parts list
Quantity Part number Description
1ea
1 ea 063-4477-00
1 ea 071-2179-XX
1 ea 071-3098-00
2 ea 211-1050-00
4 ea 211-1081-00
1 ea 335-3035-00
1 ea 407-5337-00
1 ea 407-5473-00
1 ea 650-5632-00
NS SOFTWARE COA (CERTIFICATE OF
AUTHENTICITY); MICROSOFT WINDOWS XP
PRO EMBEDDED ENTERPRISE SP3, FOR
EMBEDDED SYSTEMS
BIOS PREP, USB FLASH DRIVE, BIOS
VERSION SOM5788L20, USE ON
SOM-5788FG-U0A1E ONLY, WIN7, WINXP,
32-BIT AND 64-BIT SUPPORT
MANUAL, TECH; SVCPT-UPG; TEKTRONIX
SUPPLEMENTAL INFORMATION SHEET FOR
THE PEOPLES REPUBLIC OF CHINA; CHINA
ROHS
MANUAL, TECH; INSTALLATION, RSA6BUP
WINXP, ONLY FOR RSA6120B UPGRADE
SCREW, MACHINE; 6-32 X 0.312 L, PNH,
STEEL, ZINC FINISH, T15
SCREW, MACHINE; M3 X 0 .5 X 3.5MM,
FLAT WAFER HD W/SERRATIONS STRESS
RELIEVED, PHL, ZINC P LATED STEEL
MARKER, ID, REMOVABLE HARD DRIVE
WINXP
BRACKET, R HDD; SATA COMBO CABLE
RETENTION
BRACKET; HARD DRIVE 2.5 INCH
REMOVABLE
"DISK DRIVE A SSEMBLY; REMOVABLE HARD
DRIVE, PROGRAMMED, RSA61XXB SERIES,
WINXP
2 R SA6BUP Option WINXP Upgrade
Overview
Overview
There are two
instruments. The first step consists of removing current instrument drives and
installing the Windows XP removable hard drive. The second step involves
updating the BIOS in the instrument.
The procedure for installing the removable hard drive on your instrument depends
on the hard drive currently installed in your instrument. If your instrument has a
removable hard drive (option 56), the first major step of the upgrade consists of
replacing the removable drive currently installed with the new replaceable hard
drive sup
internal hard drive only (Option 59) you will remove the existing drive(s) and
install the removable hard drive supplied in this k it.
If your RSA6120B has Option 57 (DVD-R/W drive and internal hard drive) or
Option 59 (Internal Hard Disk Drive only), proceed with Removing Option 57 and
Option 59 Installed Drives. (Seepage4.)
If your RSA6120B has Option 56, proceed with Replacing an Existing Removable
Hard Drive. (Seepage11.)
NOTE. If your instrument already has a removable hard drive installed, you will
not use all the parts supplied in this kit because your instrument already has
ecessary internal parts installed.
the n
major steps required to install Option WINXP in RSA6120B
plied in this kit. If your instrument has a DVD drive (Option 57) or an
RSA6BUP Option WINXP Upgrade 3
Removing option 57 and option 59 installed drives
Removing option 57 and option 59 installed drives
This section explains how to remove Option 57 (DVD-R/W drive and internal hard
drive), or Option 59 (Internal Hard Disk Drive only) drives from your instrument.
The section f
Minimum tool and equipment list
ollowing this one describes the installation of the new drive.
The followi
ng tools are required to remove the instrument covers and to remove
and install the new drive(s). All tools are standard tools that should be readily
available.
Table 1: Tools required for installation
Item
no. Name Description
1
2 No. 2 Phillips
3
4
6
Screwdriver
handle
(magnetic)
or Pozidriv tip
T15 TORX
tip
T20 TORX
tip
5/32-in. hex
wrench
Torque driver handle. Accepts 1/4-in. hex-head driver tips
Phillips or Pozidriv-driver tip for number 2 size screw heads
TORX driver tip for T15 size screw heads
TORX driver tip for T20 size screw heads
Hex wrench to remove Allen head screws at front of top cover
These instructions are for qualified service personnel who are familiar
with servicing the product. If you need further details for disassembling or
ssembling the product, refer to the RSA6100B Series Real-Time Signal
rea
Analyzers Service Manual, Tektronix part number 077-0648-XX.
Removing a DVD drive and internal hard drive (Option 57 or option 59)
NOTE. Right-side or left-side references in these instructions assume you are
viewing the instrument from the front panel.
WARNING. To avoid electric shock, switch off the instrument power, then
disconnect the power cord from the mains power. Failure to do so could result
in injury or death.
4 R SA6BUP Option WINXP Upgrade
Removing option 57 and option 59 installed drives
If you have Opti
remove the DVD drive and the internal hard drive from your instrument.
If you have Opt
to remove the internal hard drive from your instrument.
1. Remove the p
2. If it is installed, pull the front cover off the instrument.
3. Remove the two T20 screws that secure the plastic carrying handle to the side
of the instrument. (It is not necessary to remove the black metal handles.)
(See Figur
4. Remove four T15 Torx-drive screws along each side that secure the top and
bottom co
near the front edge of the top cover (next to the folding handles).
5. Remove t
on the sides of the top cover outward, flexing them slightly to clear the
instrument chassis, and pull it away from the instrument.
on 57 (DVD drive) installed in your instrument, you have to
ion 59 (internal hard drive) installed in your instrument, you have
ower cord.
e1.)
vers to the instrument, and remove two 5/32-in. Allen head screws
he top cover by pulling straight back about 1 inch. Then pull out
RSA6BUP Option WINXP Upgrade 5
Removing option 57 and option 59 installed drives
Figure 1: Removing the top cosmetic cover.
6. Remove the 18 T15 screws that secure the top internal cover to the chassis,
and then remove the top internal cover from the instrument.
Removing a DVD drive
6 R SA6BUP Option WINXP Upgrade
1. Re
2. Di
move the two black screws securing the DVD bezel to the front panel
and remove the bezel.
sconnect the SATA cable and power cable from the PC Carrier board. Pull
the SATA cable and power cable back through the metal bracket, a way from
the PC Carrier board.
Removing option 57 and option 59 installed drives
3. Pull the DVD drive out from the front of the chassis, pulling the SATA and
power ca
ble out with the drive.
4. Place the removed DVD drive and cabling in antistatic packaging and store it
in a pro
to your organizations security protocols.
tected location for possible future us e or discard the drive, according
RSA6BUP Option WINXP Upgrade 7
Removing option 57 and option 59 installed drives
Removing the internal hard
drive
1. Disconnect the
out of the way.
two video cables fr om the PC carrier board. Move the cables
2. Remove the four screws at the corners of the hard disk drive mounting plate
that secure the mounting plate to the instrument.
3. Lift the hard disk drive mounting plate out of the instrument. Disconnect the
SATA cable from the hard disk drive.
4. Remove the four screws that secure the hard disk drive to the mounting plate.
8 R SA6BUP Option WINXP Upgrade
Installing a new removable hard drive
5. Place the remov
location for possible future use or discard the drive.
NOTE. If you discard or recycle the removed drive, be sure to follow your
organization’s security protocols to ensure the destruction of sensitive data.
6. Reinstall the hard disk drive mounting plate in the chassis and reconnect the
ribbon cables to the PC Carrier board.
ed hard drive in antistatic packaging and store it in a protected
Installing a new removable hard drive
This section describes how to install a removable hard drive in instruments that do
not already have a removable hard drive.
Installing the Option WINXP removable hard disk drive
To perform the following procedure you must have already removed Option 57
or 59 from your instrument. (See page 4, Removing a DVD drive and internal
harddrive(Option57oroption59).)
1. Attach the removable hard drive to the removable hard disk drive bracket
(part number 407-5473-XX) with four screws (part number 211-1081-XX)
using a torque driver with a T1 tip. Tighten the screws to 4.0 in-lbs.
2. Attach the removable hard drive label to the removable hard drive bracket.
Start by centering one end of the label and making it flush with the bracket.
Make sure the label is correctly oriented with the bottom of the label aligned
with the bottom of the bracket.
RSA6BUP Option WINXP Upgrade 9
Installing a new removable hard drive
3. Slide the remov
secure the hard drive with the two thumbscrews.
4. Connect the SATA and power cable c onnector to the connector on the
removable hard drive.
5. Slide the SATA combo cable retention bracket (part number 407–5337–00)
over the cable and secure the retention bracket with two screws (part number
211-1050-XX) using a torque driver with a T15 tip. Tighten the screws
to 4.0 in-lbs.
able hard disk drive assembly into the drive opening and
6. Reinstall the top internal cover:
a. Position the top internal cover on the instrument, so that the protrusions in
the cover match up with the slots in the chassis.
b. Reinstall the 18 T15 screws to secure the cover to the chassis. Tighten
these screws to 8.0 in/lb.
10 RSA6BUP Option WINXP Upgrade
Replacing an existing removable hard drive
7. Reinstall the t
a. Place the instrument on its rear feet, so the front panel is facing up and
the top is towa
b. Place the top cover over the top of the instrument and slide it toward
the front pa
on the rear panel on all three sides.
c. Reinstall t
the top cover to the instrument, near the front edge of the top cover (next
to the folding handles).
d. Align the four screw holes on each side in the top and bottom covers with
the holes in the chassis, and install eight T15 screws, four on each side.
Tighten these screws to 8.0 in/lb.
e. Position the plastic carrying handle and its bracket on the right side of
the instrument, and install the two T20 screws that secure it in place.
Tighten these screws to 8.0 in/lb.
8. Reinstall the power cord.
This completes the installation of the removable hard drive. Proceed to Update
the Instrument BIOS.(Seepage12.)
op and bottom cosmetic covers and carrying handle:
rd you.
nel. Make sure that the top cover wraps around the flanges
he four 5/32” hex head screws (two on each side) that secure
NOTE. If you need to restore the operating system on your instrument, use the
operating system restore procedure in the RSA6100B S eries Service manual. You
download the manual from the web at www.tektronix.com/manuals. There is
can
no cost to download the manual. Do not use the operating system restore disk
that originally shipped with your instrument or any operating system restore disks
you might have created to restore the operating system on your new removable
hard drive.
Replacing an existing removable hard drive
If your instrument already has a removable hard drive (Option 56), y ou
must replace the installed Windows 7-based removable hard drive with the
Windows XP-based removable hard drive supplied in this kit.
To install the new removable drive:
1. Shut down the instrument.
2. Loosen the thumb screws that secure the removable hard drive and pull the
removable hard drive out of the instrument.
RSA6BUP Option WINXP Upgrade 11
Update the instrument BIOS
Place the remov
protected location for possible future use or discard the drive, according to
your organizations security protocols.
3. Insert the Windows XP- based removable hard drive supplied with this kit into
the instrument. Tighten the thumb screws to secure the removable hard drive.
This completes the installation of the Windows XP-based removable hard drive.
Proceed to Update the Instrument BIOS.(Seepage12.)
ed drive assembly in antistatic packaging and store it in a
Update the instrument BIOS
To update the instrument BIOS:
WARNING. To avoid making the instrument unusable, do not remove power from
the inst
the BIOS update, you will have to return the instrument to Tektronix for service.
1. Configu
rument while the BIOS update is in progress. If the power is lost during
re the instrument for a BIOS update:
a. Turn the instrument off.
b. Loosen the thumb screws that secure the removable hard drive and
remove the removable hard drive from the instrument.
c. Connect a keyboard (PS/2 or USB) to the instrument.
d. Install the provided USB flash drive, part number 063-4477-00, into
a rear USB slot.
2. Update the instrument BIOS:
a. Turn on the instrument.
The instrument will boot into DOS by booting from the USB flash drive.
12 RSA6BUP Option WINXP Upgrade
Update the instrument BIOS
b. When the DOS prompt appears, enter bios to start the update.
c. At the prompt Do you want to flash the [5788N202.bin] new
s (Y/N)?
bio
,enterY.
RSA6BUP Option WINXP Upgrade 13
Update the instrument BIOS
d. At the prompt, PDR region already exists in flash. You
may lose important da ta. Do you want to continue
(Y/N)?
, type Y and press Enter.
The update utility then erases the flash, programs the flash, verifies the
flash, and then updates the EEPROM.
14 RSA6BUP Option WINXP Upgrade
Update the instrument BIOS
When the B
IOS update is complete, the utility will return to the
prompt.
e. Turn off
the instrument. Remove the power cord.
3. Post-update instrument configuration:
a. Remove the USB Flash drive from the rear panel.
b. Insert the WINXP removable drive supplied with this kit into the
instrument. Tighten the thumbscrews.
c. Wait 20 seconds a fter installing t he removable hard drive.
d. Connect the power cord to the instrument.
4. Configure the SATA mode:
a. Tur
nontheinstrument.
C:\BIOS>
RSA6BUP Option WINXP Upgrade 15
Update the instrument BIOS
b. Enter the BIOS s
a. Tap the DELETE key on the keyboard to enter the BIOS setup utility
while the Tekt
b. Use the right arrow k ey to select the Advanced menu, then press the
down arrow key to select SATA Configur atio n and press Enter.
etup utility:
ronix screen is displayed.
c. Use the up/down arrows to select SATA Mode and press Enter.
16 RSA6BUP Option WINXP Upgrade
Update the instrument BIOS
d. Use the up/down arrows to select IDE Mode and press Enter
e. Confirm the IDE Mode has been selected.
RSA6BUP Option WINXP Upgrade 17
Update the instrument BIOS
f. Press ESC to go up a menu level, then use the right arrow to select the
Save & Exit menu, then use the up/down arrow keys to select Save
Changes & Exit and press Enter.
g. When the confirmation dialog appears, select Ye s and press Enter.
18 RSA6BUP Option WINXP Upgrade
Installing the Windows Certificate of Authenticity label
After rebooting, the instrument will cycle power (on->off->on), boot to
Windows XP and launch the RSA application. After the RSA application is
launched, the instrument is ready to use.
Installing the Windows Certificate of Authenticity label
Place the supplied Windows XP Certificate of Authenticity on the rear panel.
ompletes the installation of the RSA6BUP WINXP upgrade kit.
This c
■ End of Document ■
RSA6BUP Option WINXP Upgrade 19
Loading...