xx
RSA6100B Series Real-Time Signal Analyzers
RSA5100A Series Real-Time Signal Analyzers
RSA6BUP and RSA5UP Option 56, Option 57, and
ZZZ
Option 59 Upgrades
Instructions
www.tektronix.com
P071286302*
*
071-2863-02
Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries
or suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication
supersedes that in all previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14150 SW Karl Braun Drive
P.O. B o x 5 0 0
Beaverto
USA
For product information, sales, service, and technical support:
n, OR 97077
In North America, call 1-800-833-9200.
Worl dwid e, v isit www.tektronix.com to find contacts in your area.
Table of Contents
Service Safety Summary.......................................... ................................ ................. 1
Kit Description........................................... ................................ ........................... 2
Products ................................ ................................ ................................ ......... 2
Kit Parts Li
Removing the Installed Drives.................................................................................... 7
Minimum Tool and Equipment List ...................... ................................ ................... 7
Removing a Removable Hard Disk Drive (Option 56).................................................... 7
Removing a DVD Drive and Internal Hard Drive (Option 57 or Option 59) .............. ............. 8
Installing New Drive Options . .... . ..... . .... . ..... . ..... ..... . ..... . .... . ..... . ... . . ..... . .... . ..... . ..... ..... . 12
Install
Installing Option 57: DVD-R/W Drive and Internal Hard Drive..... . ..... . .... . ..... . ... . . ..... . .... . . 14
Installing Option 59: Internal Hard Drive .... . .... . . .... . ..... . ..... . ... . . ..... . ..... . ... . . . .... . ..... . ... 21
st .............. ................................ ................................ ..................... 2
ing Option 56: Removable Hard Disk Drive ....................................................... 12
RSA6BUP and RSA5UP Options 56, 57, and 59 Upgrades i
Table of Contents
ii RSA6BUP and RSA5UP Options 56, 57, and 59 Upgrades
Service Safety Summary
Only qualified personnel should perform service procedures. Read this Service
Safety Summary and the General Safety Summary located in the RSA6100B
Real-Time Si
and RSA5100A Real-Time Signal Analyzer Service manual (Tektronix part number
077-0522-XX) before performing any service procedures.
Do Not Service Alone. Do not perform internal service or adjustments of this
product unless another person capable of rendering first aid and resuscitation is
present.
Disconnect Power. To avoid electric shock, switch off the instrument power, then
disconnect the power cord from the mains power.
UseCareWhenServicingWithPowerOn. Dangerousvoltagesorcurrentsmay
exist i
disconnect test leads before removing protective panels, soldering, or replacing
components.
To avoid electric shock, do not touch exposed connections.
gnal Analyzer Service manual (Tektronix part number 077-0648-XX)
n this product. Disconnect power, remove battery (if applicable), and
RSA6BUP and RSA5UP Options 56, 57, and 59 Upgrades 1
Kit Description
Kit D escription
Products
This kit describes the installation of each of the three hard drive upgrade options
(Option 56, Option 57, and Option 59) in an RSA6100B Series or RSA5100A
Series Real-
Time Signal Analyzer.
Kit Parts List
RSA6BUP Option 56
Removable Hard Drive
Parts L
RSA6100B S e
ries. All serial numbers.
RSA5100A Series. All serial numbers.
The following parts lists detail the parts included with your upgrade kit. The parts
shipped in your kit depend on the kit option you ordered.
Quantity Part number Description
1 e a 071-28
ist
1 ea 071-2179-XX
2 ea 211-1050-XX
4 ea 211-1081-XX
1 ea 407-5337-XX
1 ea 407-5473-XX
ea
1
63-XX
50-5486-XX
6
MANUAL, TECH: RSA6KB, RSA5KA 56, 57, 59
INSTALLATION INSTRUCTIONS
MANUAL, TECH; SVCPT-UPG; TEKTRONIX
EMENTAL INFORMATION SHEET FOR
SUPPL
THE PEOPLES REPUBLIC OF CHINA; CHINA
ROHS
SCREW, MACHINE; 6-32 X 0.312 L, PNH,
L, ZINC FINISH, T15
STEE
EW, MACHINE; M3 X 0.5 X 3.5MM,
SCR
FLAT WAFER HD W/SERRATIONS STR ESS
RELIEVED, PHL, ZINC PLATED STEEL
BRACKET, RHDD; SATA COMBO CABLE
TENTION
RE
ACKET; HARD D RIV E 2.5 INCH
BR
REMOVABLE
DRIVE ASSEMBLY; REMOVABLE HARD
DRIVE, PROGRAMMED, RSA61XXB SERIES;
PT 56
O
2 RSA6BUP and RSA5UP Options 56, 57, and 59 Upgrades
Kit Description
RSA5UP Option
56
Removable Hard Drive
Parts List
Quantity Part number Description
1 ea 071-2863-XX
1 ea 071-2191-XX
2 ea 211-1050-XX
4 e a 211-1081-
1 ea 407-5337-XX
1 e a 407-547
1 ea 650-5353-XX
XX
3-XX
MANUAL, TECH: RSA6KB, RSA5K 56, 57, 59
INSTALLATION
MANUAL, TECH
SUPPLEMENTAL INFORMATION SHEET FOR
THE PEOPLES REPUBLIC OF CHINA; CHINA
ROHS
SCREW, MACH
STEEL, ZINC FINISH, T15
SCREW, MACHINE; M3 X 0.5 X 3.5MM,
FLAT WAFER HD W/SERRATIONS S TRESS
RELIEVED
BRACKET,
RETENTION
BRACKET; HARD DRIVE 2.5 INCH
REMOVABLE
DRIVE ASSEMBLY; REMOVABLE HARD
PROGRAMMED, RSA5XXX SERIES
DRIVE,
INSTRUCTIONS
; SVCPT-UPG; TEKTRONIX
INE; 6-32 X 0.312 L, PNH,
, PHL, ZINC PLATED STEEL
RHDD; SATA COM BO CABLE
RSA6BUP and RSA5UP Options 56, 57, and 59 Upgrades 3
Kit Description
RSA6BUP Optio
n57
Internal HDD and DVD-R /
CD-RW Parts List
Quantity Part number Description
1 ea 071-2863-XX
1 ea 071-2179-XX
1 ea 119-7678-XX
1 ea 174-5650-XX
1 ea 200-5143-XX
4 ea 210-1543-XX
4 e a 211-051
4 ea 211-1070-XX
2 ea 211-0690-XX
4 ea 211-0950-XX
4 ea 348-
1 ea 407
1 ea 650
0-XX
1835-XX
-5476-XX
-5505-XX
MANUAL, TECH: RSA6KB, RSA5K 56, 57, 59
INSTALLATION
MANUAL, TECH
SUPPLEMENTAL INFORMATION SHEET FOR
THE PEOPLES REPUBLIC OF CHINA; CHINA
ROHS
OPTICAL, CD
MB/SEC, 650MEG/8.5GIG, SATA/ATAPI;TEAC
MODEL DV-W28S-V93.
CABLE, SATA-DVD, DATA AND POWER,
SAFETY CO
COVER; DV
SCREW, S
WITH VIBE ISOLATION GROMMETT)
SCREW, MACHINE; 6-32 X 0.375, PNH, ZINC
PLATED STEEL, T15
SCREW;M2X.4X2MM,PNH,PHL,STLNIPL
SCREW, MACHINE; 6-32 X 0.875, PNH, BLACK
LATED STEEL, TORX & SLOT
ZINC P
W, MACHINE; M2X.4X3L, PHL, PNH,
SCRE
STEEL, ZINC FINISH
GROMMET; VIBRATION ISOLATION
BRACKET, DVD DRIVE
DRIVE ASSEMBLY; INTERNAL FIXED DRIVE,
PROGRAMMED, RSA61XXB SERIES
INSTRUCTIONS
; SVCPT-UPG; TEKTRONIX
-RW/DVD-R/RW DVD+R/RW,16.7
NTROLLED
D
HOULDER, SPECIAL; 6-32 (USE
4 RSA6BUP and RSA5UP Options 56, 57, and 59 Upgrades
Kit Description
RSA5UP Option
57 Internal
HDD and DVD-R / CD-RW
Parts List
Quantity Part number Description
1 ea 071-2863-XX
1 ea 071-2191-XX
1 ea 119-7678-XX
1 ea 174-5650-XX
1 ea 200-5143-XX
4 ea 210-1543-XX
4 e a 211-051
2 ea 211-0690-XX
4 ea 211-0950-XX
4 e a 211-
4 ea 348-
1 ea 407
1 ea 650
0-XX
1070-XX
1835-XX
-5476-XX
-5352-XX
MANUAL, TECH: RSA5K 56, 57, 59
INSTALLATION
MANUAL, TECH
SUPPLEMENTAL INFORMATION SHEET FOR
THE PEOPLES REPUBLIC OF CHINA; CHINA
ROHS
OPTICAL, CD
MB/SEC, 650MEG/8.5GIG, SATA/ATAPI;TEAC
MODEL DV-W28S-V93.
CABLE, SATA-DVD, DATA AND POWE R,
SAFETY CO
COVER; DV
SCREW, S
WITH VIBE ISOLATION GROMMETT)
SCREW, MACHINE; 6-32 X 0.375, PNH, ZINC
PLATED STEEL, T15
SCREW, MACHINE; 6-32 X 0.875, PNH, BLACK
LATED STEEL, TORX & SLOT
ZINC P
, MACHINE; M2X .4X3L, PHL, PNH,
SCREW
STEEL, ZINC FINISH
SCREW; M2 X .4 X 2MM, PNH, PHL, STL NI PL
GROMMET; VIBRATION ISOLATION
BRACKET, DVD DRIVE
DRIVE ASSEMBLY; INTERNAL FIXED DRIVE,
PROGRAMMED, RSA5XXX SERIES
INSTRUCTIONS
; SVCPT-UPG; TEKTRONIX
-RW/DVD-R/RW DVD + R/RW, 16.7
NTROLLED
D
HOULDER, SPECIAL; 6-32 (USE
RSA6BUP and RSA5UP Options 56, 57, and 59 Upgrades 5
Kit Description
RSA6BUP Optio
n59
Internal Hard Disk Drive
RSA5UP Option 59 Internal
Hard Disk Drive
Quantity Part number Description
1 ea 071-2863-XX
1 ea 071-2179-XX
1 ea 200-5134-XX
1 ea 200-5143-
4 e a 210-1543
4 ea 211-0510-XX
4 ea 348-1835-XX
1 ea 650-5505-XX
Quantity Part number Description
1 ea 071-2863-XX
1 ea 071-2191-XX
1 ea 200-5134-XX
4 ea 210-1543-XX
4 ea 211-0510-XX
4 ea 211-0690-XX
4 ea 348-1835-XX
1 ea 650-5352-XX
XX
–XX
MANUAL, TE CH: RSA5K 56, 57, 59
INSTALLATION
MANUAL, TECH
SUPPLEMENTAL INFORMATION SHEET FOR
THE PEOPLES REPUBLIC OF CHINA; CHINA
ROHS
CABLE, SATA
SAFETY CONTROLLED
COVER; EMPTY DRIVE BAY
SCREW, SHOULDER, SPECIAL; 6-32 (USE
WITH VIBE ISOLATION GROMMETT)
SCREW, MACHINE; 6-32 X 0.375, PNH, ZINC
PLATED S
GROMMET
DRIVE A
PROGRAMMED, RSA61XXB SERIES
MANUAL, TE CH: RSA5K 56, 57, 59
INSTALLATION INSTRUCTIONS
MANUAL, TECH; SVCPT-UPG; TEKTRONIX
SUPPLEMENTAL INFORMATION SHEET FOR
THE PEOPLES REPUBLIC OF CHINA; CHINA
ROHS
COVER; EMPTY DRIVE BAY
SCREW, SHOULDER, SPECIAL; 6-32 (USE
WITH VIBE ISOLATION GROMMETT)
SCREW, MACHINE; 6-32 X 0.375, PNH, ZINC
PLATED STEEL, T15
SCREW, MACHINE; 6-32 X 0.875, PNH, BLACK
ZINC PLATED STEEL, TORX & SLOT
GROMMET; VIBRATION ISOLATION
DRIVE ASSEMBLY; INTERNAL FIXED DRIVE,
PROGRAMMED, RSA5XXX SERIES
SSEMBLY; INTERNAL FIXED DRIVE,
INSTRUCTIONS
; SMPLP; TEKTRONIX
-DVD, DATA AND POWER,
TEEL, T15
; VIBRATION ISOLATION
6 RSA6BUP and RSA5UP Options 56, 57, and 59 Upgrades
Removing the Installed Drives
This section contains all the procedures to remove Option 56 (Removable Hard
Disk Drive), Option 57 (DVD-R/W drive and internal hard drive), or Option 59
(Internal Ha
this one describes the installation of the new drive(s).
Minimum Tool and Equipment List
The following tools are required to remove the instrument covers and to remove
and install the new drive(s). All tools are standard tools that should be readily
available.
Table 1: Tools required for installation
Item
no. Name Descrip
1
2 No. 2 Phillips
3
4
6
rd Disk Drive only) from your signal analyzer. The section following
iver
Screwdr
handle
(magnetic)
or Pozidriv tip
T-15 TORX
tip
TORX
T-20
tip
5/32-in. hex
wrench
Removing the Installed Drives
tion
Torque d
Phillips or Pozidriv-driver tip for number 2 size screw heads
TORX driver tip for T-15 size screw heads
TORX
Hex wrench to remove Allen head screws at front of top cover
river handle. Accepts 1/4-in. hex-head driver tips
driver tip for T-20 size screw heads
These instructions are for qualified service personnel who are familiar with
vicing the product. If you need further details for disassembling or reassembling
ser
the product, refer to the RSA6100B Series Real-Time Signal Analyzers Service
Manual, Tektronix part number 077-0648-XX or RSA5100A Series Real-Time
Signal Analyzers Service Manual, Tektronix part number 077-0522-XX.
Removing a Removable Hard Disk Drive (Option 56)
WAR NI NG . To avoid electric shock, switch off the instrument power, then
disconnect the power cord from the mains power. Failure to do so could result
in injury or death.
RSA6BUP and RSA5UP Options 56, 57, and 59 Upgrades 7
Removing the Installed Drives
If you are upgra
remove the drive assembly from the instrument to begin the upgrade process.
Perform the following steps to remove the removable hard disk.
1. Loosen the thumbscrews securing the drive to the front panel.
2. Grasp the dr
straight out of the instrument.
3. Place the re
protected location for possible future use or discard the drive.
dingfromOption56toOption57orOption59,youneedto
ive assembly by the thumbscrews and pull the drive assembly
moved drive assembly in anti-static packaging and store it in a
Removing a D VD Drive and Internal Hard Drive (Option 57 or Option 59)
NOTE. Right-side or left-side references in these instructions assume you are
viewing the instrument from the front panel.
WARNING. To avoid electric shock, switch off the instrument power, then
disconnect the power cord from the mains power. Failure to do so could result
ry or death.
in inju
If you are upgrading from Option 57 (DVD drive) to Option 56, you have to
ve the DVD drive and the internal hard drive from your instrument.
remo
If you are upgrading from Option 59 (internal hard drive) to Option 56, you have
move the internal hard drive from your instrument.
to re
1. Remove the power cord.
2. If it is installed, pull the front cover off the instrument.
3. Remove the two T-15 screws that secure the plastic carrying handle to the side
of the instrument. (It is not necessary to remove the black metal handles.)
(See Figure 1.)
4. Remove four T-15 Torx-drive screws along each side that secure the top and
bottom covers to the instrument, and remove two 5/32-in. Allen head screws
near the front edge of the top cover (next to the folding handles).
5. Remove the top cover by pulling straight back about 1 inch. Then pull out
on the sides of the top cover outward, flexing them slightly to clear the
instrument chassis, and pull it away from the instrument.
8 RSA6BUP and RSA5UP Options 56, 57, and 59 Upgrades
Removing the Installed Drives
Figure 1: Removing the top cosmetic cover.
6. Remove the 18 T15 screws that secure the top internal cover to the chassis,
and then remove the top internal cover from the instrument.
Removing a DVD Drive
RSA6BUP and RSA5UP Options 56, 57, and 59 Upgrades 9
1. Remove the two black screws securing the DVD bezel to the front panel
and remove the bezel.
2. Disconnect the SATA cable and power cable from the PC Carrier board. Pull
the SATA cable and power cable back through the metal bracket, away from
the PC Carrier board.
Removing the Installed Drives
3. Pull the DVD drive out from the front of the chassis, pulling the SATA and
power ca
ble out with the drive.
4. Place the removed DVD drive and cabling in anti-static packaging and store it
in a pro
tected location for possible future use or discard the drive.
10 RSA6BUP and RSA5UP Options 56, 57, and 59 Upgrades
Removing the Installed Drives
Removing the Internal
Hard Drive
1. Disconnect the
out of the way.
two video cables from the PC carrier board. Move the cables
2. Remove the four screws at the corners of the hard disk drive mounting plate
that secure the mounting plate to the instrument.
3. Lift the hard disk drive mounting plate out of the instrument. Disconnect the
SATA cable from the hard disk drive.
4. Remove the four screws that secure the hard disk drive to the mounting plate.
RSA6BUP and RSA5UP Options 56, 57, and 59 Upgrades 11
Installing New Drive Options
5. Place the remov
protected location for possible future use or discard the drive.
NOTE. If you discard or recycle the removed drive, be sure to follow your
organization’s security protocols to ensure the destruction of sensitive data.
6. Reinstall the hard disk drive mounting plate in the chassis.
ed hard drive in anti-static packaging and store it in a
Installing New Drive Options
This sections describes how to install your new drive options.
Installing Option 56: Removable Hard Disk Drive
To perform the following procedure you must have already removed Option 57
or 59 from your instrument. (See page 8, Removing a DVD Drive and Internal
Hard Drive (Option 57 or Option 59).)
1. Attach the removable hard drive to the removable hard disk drive bracket
(part number 407-5473-XX) with four screws (part number 211-1081-XX)
using a torque driver with a T1 tip. Tighten the screws to 4.0 in-lbs.
2. Attach the removable hard drive label to the removable hard drive bracket.
Start by centering one end of the label and making it flush with the b racket.
Make sure the label is correctly oriented with the bottom of the label aligned
with the bottom of the bracket.
3. Slide the removable hard disk drive assembly into the drive opening and
secure the hard drive with the two thumbscrews.
12 RSA6BUP and RSA5UP Options 56, 57, and 59 Upgrades
Installing New Drive Options
4. Connect the SAT
removable hard drive.
5. Slide the SATA combo cable retention bracket (part number 407–5337–00)
over the
211-1050-XX) using a torque driver with a T15 tip. Tighten the screws
to 4.0 in-lbs.
cable and secure the retention bracket with two screws (part number
A and power cable connector to the connector on the
6. Reinstall the top internal cover:
a. Position the top internal cover on the instrument, so that the protrusions in
the cover match up with the slots in the chassis.
b. Reinstall the 18 T15 to secure the cover to the chassis. Tighten these
screws to 8.0 in/lb.
RSA6BUP and RSA5UP Options 56, 57, and 59 Upgrades 13
Installing New Drive Options
7. Reinstall the t
a. Place the instrument on its rear feet, so the front panel is facing up and
the top is towa
b. Place the top cover over the top of the instrument and slide it toward
the front pa
on the rear panel on all three sides.
c. Reinstall t
the top cover to the instrument, near the front edge of the top cover (next
to the folding handles).
d. Align the four screw holes on each side in the top and bottom covers with
the holes in the chassis, and install eight T15 screws, four on each side.
Tighten these screws to 8.0 in/lb.
e. Position the plastic carrying handle and its bracket on the right side of
the instrument, and install the two T15 screws that secure it in place.
Tighten these screws to 8.0 in/lb.
8. Reinstall the power cord and power on the instrument.
This completes the upgrade to Option 56.
op and bottom cosmetic covers and carrying handle:
rd you.
nel. Make sure that the top cover wraps around the flanges
he four 5/32” hex head screws (two on each side) that secure
Installing Option 57: DVD-R/W Drive and Internal Hard Drive
To perform the following procedure you must have already removed Option 56
or 59 from your instrument. (See page 7, Removing a Removable Hard Disk
Drive (Option 56).)
D-R/W Drive. To install the DVD-R/W drive:
DV
1. Slide the DVD drive (part number 119-7678-XX) into the DVD bracket (part
mber 407-5476-XX) with the front of the DVD drive aligned with the tabs
nu
on the DVD bracket.
urn the assembly on its side and secure the DVD drive to the DVD bracket
2.T
with 2 screws (part number 211-0950-XX), using a T0 tip. Tighten these
screws to 0.6 in/lb.
14 RSA6BUP and RSA5UP Options 56, 57, and 59 Upgrades
Installing New Drive Options
3. Turn the assembly on to the opposite side and secure the DVD drive to the
DVD bracket using two screws (part number 211-0950-XX), using a T0 tip.
Tighten
these screws to 0.6 in/lb.
4. Attach the DVD cable (part number 174-5650-XX) to the rear of the DVD
drive.
5. Holding the DVD assembly in front of the instrument, thread the DVD cables
through the opening in the front panel and back through the hole in the back of
the of the bracket. Slide the DVD assembly into the opening in the front panel.
RSA6BUP and RSA5UP Options 56, 57, and 59 Upgrades 15
Installing New Drive Options
6. Mount the DVD cover (part number 200-5143-XX) to the front of the
instrument using two screws (part number 211-0690-XX) using a torque
driver w
ith a T-15 tip. Tighten these screws to 10 in/lb.
7. Thread the DVD cables through the bottom hole in the chassis brack et and
connect
8. Secure the DVD and HDD cables to the chassis bracket with one zip tie (part
number 343–0549–XX) as shown.
them to the PC carrier board as shown.
16 RSA6BUP and RSA5UP Options 56, 57, and 59 Upgrades
Installing New Drive Options
Install Internal Hard Drive. To install the internal hard drive:
9. Disconne
the front of the instrument.
ct the video cables from the PC carrier board and fold them over
10. RemovethefourscrewsthatsecuretheHDDbrackettothechassisand
remove the bracket.
RSA6BUP and RSA5UP Options 56, 57, and 59 Upgrades 17
Installing New Drive Options
11. Install four grommets (part number 348-1835-XX) on the HDD bracket as
shown.
12. Place the drive assembly (part number 650-5352–XX) onto the HDD bracket
with the connector appears in the cutout in the HDD bracket. Secure the drive
assembly to the HDD bracket with four screws (part number 210-1543-XX)
ing a torque drive with a P1 tip. Tighten the screws to 4.0 in-lbs.
us
18 RSA6BUP and RSA5UP Options 56, 57, and 59 Upgrades
Installing New Drive Options
13. Connect th
14. Place the drive assembly and HDD bracket on the chassis as shown. Secure
the HDD bracket to the chassis with four screws (part number 211-1050-XX)
using a torque driver with a T15 tip. Tighten these screws to 10 in/lb.
e HDD SATA cable to the drive assembly.
RSA6BUP and RSA5UP Options 56, 57, and 59 Upgrades 19
Installing New Drive Options
15. Reconnect the s
16. Reconnect the larger video cable to the PC Carrier board.
17. Reinstall the top internal cover:
a. Position the top internal cover on the instrument, so that the protrusions in
the cover match up with the slots in the chassis.
maller video cable to the PC Carrier board.
b. Reinstall the 18 T15 to secure the cover to the chassis. Tighten these
screws to 8.0 in/lb.
18. Reinstall the top and bottom cosmetic covers and carrying handle:
a. Place the instrument on its rear feet, so the front panel is facing up and
the top is toward you.
b. Place the top cover over the top of the instrument and slide it toward
the front panel. Make sure that the top cover wraps around the flanges
on the rear panel on all three sides.
c. Reinstall the four 5/32” hex head screws (two on each side) that secure
the top cover to the instrument, near the front edge of the top cover (next
to the folding handles).
d. Align the four screw holes on each side in the top and bottom covers with
the holes in the chassis, and install eight T15 screws, four on each side.
Tighten these screws to 8.0 in/lb.
e. Position the plastic carrying handle and its bracket on the right side of
the instrument, and install the two T15 screws that secure it in place.
Tighten these screws to 8.0 in/lb.
19. Reinstall the power cord and power on the instrument.
This completes the upgrade to Option 57.
20 RSA6BUP and RSA5UP Options 56, 57, and 59 Upgrades
Installing New Drive Options
Installing Op
tion 59: Internal Hard Drive
To perform the following procedure you must have already removed Option 56
from your instrument. (See page 7, Removing a Removable Hard Disk Drive
(Option 56).
To install the internal hard drive:
1. Disconnect the video cables from the PC Carrier board and fold them over
the front of the instrument.
)
2. RemovethefourscrewsthatsecuretheHDDbrackettothechassisand
remove the bracket.
3. Install four grommets (part number 348-1835-XX) on the HDD bracket as
shown.
RSA6BUP and RSA5UP Options 56, 57, and 59 Upgrades 21
Installing New Drive Options
4. Place the drive assembly (part number 650-5352–XX) onto th
with the connector appears in the cutout in the HDD bracket. Secure the drive
assembly to the HDD bracket with four screws (part number 210-1543-XX)
using a torque drive with a P1 tip. Tighten the screws to 4.0 in-lbs.
5. Connect the HDD SATA cable to the drive assembly.
e HDD bracket
22 RSA6BUP and RSA5UP Options 56, 57, and 59 Upgrades
Installing New Drive Options
6. Place the drive
the HDD bracket to the chassis with four screws (part number 211-1050-XX)
using a torque driver with a T15 tip. Tighten these screws to 10 in/lb.
7. Reconne
8. Reconnect the larger video cable to the PC Carrier board.
assembly and HDD bracket on the chassis as shown. Secure
ct the smaller video cable to the PC Carrier board.
9. Reinstall the top internal cover:
a. Position the top internal cover on the instrument, so that the protrusions in
the cover match up with the slots in the chassis.
b. Reinstall the 18 T15 to secure the cover to the chassis. Tighten these
screws to 8.0 in/lb.
RSA6BUP and RSA5UP Options 56, 57, and 59 Upgrades 23
Installing New Drive Options
10. Reinstall the t
a. Place the instrument on its rear feet, so the front panel is facing up and
the top is towa
b. Place the top cover over the top of the instrument and slide it toward
the front pa
on the rear panel on all three sides.
c. Reinstall t
the top cover to the instrument, near the front edge of the top cover (next
to the folding handles).
d. Align the four screw holes on each side in the top and bottom covers with
the holes in the chassis, and install eight T15 screws, four on each side.
Tighten these screws to 8.0 in/lb.
e. Position the plastic carrying handle and its bracket on the right side of
the instrument, and install the two T15 screws that secure it in place.
Tighten these screws to 8.0 in/lb.
11. Reinstall the power cord and power on the instrument.
This completes the upgrade to Option 59.
op and bottom cosmetic covers and carrying handle:
rd you.
nel. Make sure that the top cover wraps around the flanges
he four 5/32” hex head screws (two on each side) that secure
24 RSA6BUP and RSA5UP Options 56, 57, and 59 Upgrades
Loading...