Tektronix DPO4VID, DPO4AUTO, DPO4COMP, DPO4AUTOMAX, DPO4PWR Declassification

xx

MDO4000B Series Oscilloscopes and Application Modules

ZZZ

Declassification and Security

Instructions

www.tektronix.com

P077085800*

*

077-0858-00

Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries
or suppliers, and are protected by national copyright laws and international treaty provisions.

Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication
supersedes that in all previously published material. Specifications and price change privileges reserved.

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

TekSecure is a trademark of Tektronix, Inc.

Contacting Tektronix

Tektronix, Inc.
14150 SW Karl Braun Drive
P.O . B ox 50 0
Beaverton, OR 97077
USA

For product information, sales, s ervice, and technical support:

In North America, call 1-800-833-9200.
Worl d wide, vi s it www.tektronix.com to find contacts in your area.

Table of Contents

Preface .............................................................................................................. iii

Clear and Sanitize Procedures. ... ... . .. . ... ... . ... ... ... . ... ... . ... ... ... . ... ... ... . ... ... . .. . ... ... . ... ... ... . ... 1

Memory Devices............................................................................................... 2

Data Export

Sanitizing an Application Module .. ... . .. . ... ... . ... ... . ... ... ... . ... ... . .. . ... ... . ... ... ... . ... ... . ... ... .. 5

Built-In Security Features .................. ................................ ................................ ....... 7

Disable the LAN Port and Clear LAN Ethernet Settings.. . .. . ... ... . ... ... ... . ... ... ... . ... ... . ... ... ... . 9

Disable the USB Device Port................................................................................ 10

Clear and Sanitize a Nonfunctional Instrument . ... . ... ... . .. . ... ... . .. . ... ... . .. . ... ... . .. . ... ... . ... ... ... . .. 11

Devices........................................................................................... 4

MDO4000B Series Oscilloscopes and Application Modules Declassification and Security Instructions i

Table of Contents

ii MDO4000B Series Oscilloscopes and Application Modules Declassification and Security Instructions

Preface

If you have data security concerns, this document helps you to sanitize or
remove memory devices from the Tektronix MDO4000B Series Mixed Domain
Oscilloscop

The MDO4000B Series products have data storage (memory) devices and data
output devi
the memory devices, and also tell you how to declassify an instrument that is not
functioning.

Instrument code and calibration settings reside in nonvolatile fl ash memory.
Instrument setups and reference waveforms may also be stored in flashmemoryor
on USB d rives connected to the instrument.

If you have any questions, contact the Tektronix Technical Support Center at
www.tektronix.com/support.

es and Modules.

ces (USB ports). These instructions tell you how to clear or sanitize

Reference

The procedures in this document are written to meet the requirements specified in:

NISPO

ISFO Process Manual for Certification & Accreditation of Classified Systems
under

M, DoD 5220.22–M, Chapter 8

NISPOM

MDO4000B Series Oscilloscopes and Application Modules Declassification and Security Instructions iii

Preface

Products

The following T

Oscilloscopes:

MDO4104B-6

MDO4104B-3

MDO4054B-6

MDO4054B-3

MDO4034B-

MDO4014B-3

Application Modules:

DPO4AERO

DPO4AUDIO

DPO4AUTO

DPO4AU

DPO4COMP

DPO4EMBD

ektronix products are covered by this document:

3

TOMAX

DPO4ENET

DPO4LMT

DPO4PWR

4USB

DPO

DPO4VID

MDO4TRIG

iv MDO4000B Series Oscilloscopes and Application Modules Declassification and Security Instructions