Teknatool NOVA Instruction Manual

119-0811-001 1

NOVA

DVR Wireless Remote II

Publication 119-0811-001

ESL 1

Instruction Manual

119-0811-001 2

NOVA DVR Wireless Remote

Features:

 Fits on any “Remote II Ready” NOVA DVR Wood Lathe.
 Wireless control convenience at your fingertips.
 Start, stop and speed adjustments.
 Suitably sized buttons for rapid reference and control.
 Invaluable for long spindle work or large platters/bowls when

you can't be close to the headstock.

 2.4 GHz Radio Frequency (RF) operation (FCC Compliant).
 Range up to 23 feet ( 7 meter ) line of sight.
 Up to 1 years stand-by battery life.
 Up to 6 months battery life with up to 20 commands per day.
 1-Year warranty excludes battery.

NOTE:

 All values are approximate and calculated under the specific test conditions. For

end users, these values might be varied according to workshop conditions, other
electronic equipment interference, battery types and operation distance, etc.

 Wireless Remote may not be available in all countries/markets or may require an

additional optional accessory Retro Fit Kit for older DVR lathes. See our website
or your NOVA Retailer for more information.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1). This device may not cause harmful interference, and
(2). This device must accept any interference received, including interference that may cause undesired
operation.

Note:

Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment

119-0811-001 3

Contact Teknatool

New Zealand

Teknatool International Ltd

Phone: [phone]
Fax: [phone]
Email:

[e-mail]

Website: www.teknatool.com

Carbatec New Zealand

Phone: [phone]
Email:

[e-mail]

Website: www.carbatec.co.nz

United States

Teknatool Service Center

Phone: [phone]
Free Phone: [phone]
Free Fax: [phone]
Email: [e-mail]
Website: www.teknatool.com

Woodcraft Supply Corp

Technical Service: 1-800-535-4486
Orders: 1-800-225-1153
Website:

www.woodcraft.com

Australia

Carbatec Australia

Phone: [phone]
Free Fax: [phone]
Email:

[e-mail]

Website: www.carbatec.com.au

Canada

KMS Tools and Equipment Ltd

Phone: [phone]
Free Phone: [phone]
Fax: [phone]
Email:

[e-mail]

Website: www.kmstools.com

Netherlands

Baptist voor Houtbewerkers

Tel: [phone]
Website: http://www.baptist.nl

United Kingdom

Brimarc Tools and Machinery

Phone: [phone]
Fax: [phone]
Email:[e-mail]
Website:www.brimarc.com/nova

Austria

Neureiter

Phone:[phone]
Fax: [phone]
Email:

[e-mail]

France

OTELO

Phone: [phone]
Fax: [phone]
Website:

www.otelo.fr

MAISON DU TOURNAGE

Phone: [phone]
Fax [phone]

Email:

[e-mail]

Norway

VERKTOY AS

Phone: [phone]
Fax: [phone]
Email:

[e-mail]

Website: www.verktoyas.no

Belgium

Willy Vanhoutte BVBA

Phone [phone]
Fax + 32 (50) 78 19 64
Email:

[e-mail]

Website: http://www.willyvanhoutte.be

South Africa

The Hardware Centre

Phone: [phone]
Fax: [phone]
Website:

www.hardwarecentre.co.za

119-0811-001 4

Email: [e-mail]

Table of Contents:

GENERAL SAFETY RULES ................................................................. 5

ADDITIONAL SAFETY RULES: ............................................................ 7

Installation Instructions:......................................................................... 8

Remote Button Layout: ....................................................................... 11

Operating instructions: ........................................................................ 12

Troubleshooting: ................................................................................. 13

Battery Replacement: ...................................................................... 13

Remote Retro-Fit Kit: .......................................................................... 14

© Copyright 2001-2010 by Teknatool International; All Rights Reserved.
Nova DVR is a trademark of Teknatool International Ltd.

The information and specifications contained herein are subject to change. Teknatool is not
responsible for errors or omissions herein or for incidental damages in connection with the
furnishing or use of this information.

119-0811-001 5

GENERAL SAFETY RULES

!

Warning! Failure to follow these rules may result in serious personal injury.

IMPORTANT: THIS REMOTE IS NOT INTENDED FOR USE AS AN
EMERGENCY DEVICE AND SHOULD NOT BE RELIED UPON AS SUCH

1. FOR YOUR OWN SAFETY, READ THE MANUAL BEFORE

OPERATING THE TOOL. Learn the machine’s application,
limitations and the specific hazards particular to it.

2. ALWAYS USE A FULL FACE SHIELD. Strongly recommended.

(Must comply with ANSI STANDARD Z87.1 -USA) Everyday eye­glasses usually are only impact resistant and safety glasses only
protect eyes. A full face shield will protect the eyes and face. Also
use face or dust mask if cutting operation is dusty.

3. WEAR PROPER APPAREL. Do not wear loose clothing, gloves,

neckties, rings, bracelets or other jewelry which may get caught in
moving parts. Non-slip footwear is recommended. Wear protective
hair covering to contain long hair.

4. USE EAR PROTECTORS. Use ear plugs or muffs for any period of

operation. Use muffs rated to 103 DBA LEQ (8 hour).

5. DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use power

tools in damp or wet locations, or expose them to rain. Keep work
area well lighted. The DVR Wood Lathe is intended for indoor use
only. Failure to do so may void the warranty.

6. KEEP WORK AREA CLEAN. Cluttered areas and benches invite

accidents. Build-up of sawdust is a fire hazard.

7. KEEP CHILDREN AND VISITORS AWAY. The Nova DVR is not

recommended for children or the infirm. Such personnel and
onlookers should be kept at a safe distance from the work area.

8. MAKE WORKSHOP CHILDPROOF. Utilize locks, master switches,

or by removing starter/lockout keys.

9. GROUND ALL TOOLS. If the tool is equipped with a three-prong

plug, it should be plugged into a three hole electrical receptacle. If an
adapter is used to accommodate a two prong receptacle, the
adapter plug must be attached to a known ground. NEVER remove
the third or grounding prong.

10. DISCONNECT TOOLS. Ensure the plug is removed from the wall

socket before servicing and when changing accessories such as
blades, bits, cutters and fuses, etc.

11. AVOID ACCIDENTAL STARTING. Make sure switch is in the Off

position before plugging in power cord into the wall socket.

119-0811-001 6

12. NEVER LEAVE MACHINE RUNNING UNATTENDED. Do not

leave machine unless it is turned off and has come to a complete
stop.

13. KEEP GUARDS IN PLACE. Ensure guards are in working order.

14. USE CORRECT TOOLS. Do not use a tool or attachment to do a job

for which it was not designed.

15. DON’T FORCE THE TOOL. It will do the job better and be safer at the

rate/force for which it was designed.

16. MAINTAIN TOOLS IN TOP CONDITION. Keep tools sharp and clean

for the best and safest performance. Follow instructions for lubricating
and changing accessories.

17. NEVER STAND ON THE TOOL. Serious injury could occur if the tool

is tipped or if the cutting tool is accidentally contacted.

18. REMOVE ADJUSTING KEYS AND WRENCHES. Form a habit of

checking to see that keys and adjusting wrenches are removed from
tool before turning it on.

19. DON’T OVERREACH. Keep proper footing and balance at all times.

20. DIRECTION OF FEED. Feed work into the blade or cutter against the

direction of rotation.

21. ATTENTION TO WORK. Concentrate on your work. If you become

tired or frustrated, leave it for awhile and rest.

22. SECURE WORK. Use clamps or a vice to hold work when practical.

It’s safer than using your hand and frees both hands to operate tool.

23. CHECK DAMAGED PARTS. Before further use of the tool, any part

that is damaged should be carefully checked to ensure that it will
operate properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts, mounting, and any
other conditions that may affect its operation. Any damaged part
should be properly repaired or replaced.

24. DRUGS, ALCOHOL OR MEDICATION. Do not operate machine while

under the influence of drugs, alcohol, or any medication.

25. DUST WARNING. The dust generated by certain woods and wood

products can be harmful to your health. Always use an approved dust
mask and operate machinery in well-ventilated areas. In addition,
provide a means for proper dust removal. Use wood dust collection
systems whenever possible.

119-0811-001 7

ADDITIONAL SAFETY RULES:

!

Warning! Failure to follow these rules may result in serious personal

injury. IMPORTANT: THIS REMOTE IS NOT INTENDED FOR USE AS

AN EMERGENCY DEVICE AND SHOULD NOT BE RELIED UPON

1. DO NOT RELY ON THIS DEVICE AS AN EMERGENCY STOP DEVICE.

2. DO NOT OPERATE THE WIRELESS. REMOTE UNTIL IT IS COMPLETELY
ASSEMBLED AND INSTALLED. Follow instructions and recommendations.

3. REMOTE MUST BE SECURELY FASTENED. Fasten to either wrist or to the wood
lathe with the magnetic back.

4. DO NOT GET WET. The remote may be destroyed or become inoperative if it gets
wet.

5. AVOID EXCESS SAWDUST. Limit sawdust contact with the remote.

6. FOLLOW ELECTRICAL CODES. Make sure wiring codes and recommended
electrical connections are followed and that the machine is properly grounded.

7. KEEP WORK AREA CLEAN. Do not turn the wood lathe on before clearing it of all
objects (tools, scraps of wood, etc.). Keep the nearby area and floor clear of debris.

8. CHECK SET-UP WITH SPINDLE OFF. Examine the set-up carefully and rotate the
work piece, by hand, to check clearance. In addition, check to see speed is correctly
selected before turning on spindle.

9. ALWAYS CHECK CORRECT SPEED IS SELECTED BEFORE SWITCHING ON
THE SPINDLE.

10. USE LOWEST SPEED when turning a new or unbalanced work piece.

11. TURN AT RECOMMENDED SPEED. Always operate the wood lathe at the
recommended speeds. Consult your wood lathe manual for suggested speeds.

12. WHEN ROUGHING STOCK, do not jam the wood lathe tool or chisel into work piece
or take too big/deep a cut.

13. DO NOT OPERATE LATHE IF DAMAGED OR FAULTY. If any part of your wood
lathe is missing, damaged or broken, in any way, or if any electrical component fails,
shut off the wood lathe and disconnect the wood lathe from the power supply. Replace
missing, damaged, or failed parts before resuming the operation.

14. ADDITIONAL SAFETY INFORMATION. The instruction for the safe and proper

operation of this product is available from the National Safety Council, 444 N. Michigan
Avenue, Chicago, IL 60611 in the Accident Prevention Manual of Industrial Operations
and also in the Safety Data Sheets provided by the NSC. Also refer to the American
National Standards Institute ANSI 01.1 Safety Requirements for Woodworking
Machines and the U.S Department of Labor OSHA 1910.213 Regulation.

119-0811-001 8

Installation Instructions:

1. Unpack the two parts from

packaging. The small circuit

board is the ‘Receiver
Module’ which goes in the

control panel of the wood
lathe. The larger device is
the ‘Remote’.

Receiver Module (C):

Remote:

2. Turn off the wood lathe and unplug its power cord. Wait 2
minutes for the control circuitry to power down.

3. Remove the Control Panel

from the headstock by
loosening or removing the
3 screws on the front of the
Control Panel. Gently
remove the Control Panel
from the head stock.

119-0811-001 9

Inside the Control Panel:

4. Plug the Receiver to the user interface board in the position
shown below.

119-0811-001 10

5. Put Control panel back to the on the Headstock and screw in its
three mounting screws. Check that the control panel is secure and
tighten mounting screws as necessary.

6. Power on your DVR and select the Wireless Remote in the Menu.

7. Select “Pair ID” on the screen to begin pairing procedures.

8. Press the <OFF> key on the remote to pair to the lathe, your

DVR lathe and remote should now be paired.

Note: If the remote still does not pair, please contact your local
Teknatool Agent.

.

119-0811-001 11

Remote Button Layout:

119-0811-001 12

Operating instructions:

Starting and stopping:

To start the lathe with
the remote, press and
hold the Start/Stop
button for 2 seconds.

To stop the lathe, just
press and release the
Start/Stop button
once.

Changing the speed:

To change the
operating speed of the
wood lathe with the
remote, simply press

or hold the ‘Speed Up’
or ‘Speed Down’

button.

NOTE: When
changing the speed,
the lathe can be
running or stopped.

119-0811-001 13

Troubleshooting:

Battery Replacement:

If the battery fails, you can unscrew the 2 screws on the bottom of the
remote and replaced with a CR1632 battery.

Note: The remote will still be paired with or communicate with your
NOVA DVR Lathe after battery replacement.

119-0811-001 14

Remote Retro-Fit Kit:

The NOVA DVR Wireless Remote Retro-Fit Kit enables older DVR
Wood Lathes to use the NOVA DVR Wireless Remote.

Fast and easy to fit with Step-by-Step instructions.

Suitable for all NOVA DVR Lathes.

SKU: 55519

Available online or through your NOVA Dealer.

www.teknatool.com

119-0811-001 15

© Teknatool® International 2011

All Rights Reserved. Teknatool USA, Inc.

Register your warranty online

www.teknatool.com