Teka APOLLO PILLAR series, APL series Installation Instructions Manual

APOLLO PILLAR™ (APL)

NEEDED

FOR

INSTALLATION:

1/8” Allen Wrench

Wire Connectors

Mounting Hardware

Warning Hot Surface

Wear Gloves

High Voltage

By Others

Gloves

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS

IMPORTANT - WEAR GLOVES TO AVOID GETTING FINGERPRINTS ON THIS PRODUCT. MANY TEKA ILLUMINATION PRODUCTS ARE DESIGNED TO NATURALLY PATINA.
OILS FROM YOUR SKIN WILL ACCELERATE THIS PROCESS WHERE TOUCHED AND ARE NEARLY IMPOSSIBLE TO REMOVE. THIS PROCESS OCCURS OVER TIME AND IS
DETERMINED BY THE INSTALLATION ENVIRONMENT.

INSTRUCTIONS PERTAINING TO

A RISK OF FIRE, OR INJURY TO

PERSONS IMPORTANT SAFETY

INSTRUCTIONS

Lighted fixture is HOT!
WARNING - To reduce the risk of
FIRE OR INJURY TO PERSONS:

Turn off/unplug and allow to cool before replacing LED.
Fixture gets HOT quickly! Contact only switch/plug when
turning on. Do not touch hot lens, guard, or enclosure.
Keep fixture away from materials that may burn.
Do not operate the luminaire fitting with a missing or
damaged shield. Do not touch the source at any time. Use

a soft cloth or gloves. Oil from skin may cause damage.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY

AND INSTALLATION INSTRUCTIONS

• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local and
Provincial Codes.

• Follow product label information and instructions.

• Qualified Personnel with appropriate personal protective
equipment must perform all servicing of this product.

• Before wiring to power supply and during servicing, turn off and
lock out power at fuse or circuit breaker before service.

• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause an
unsafe condition and void product warranty.

• Do not block light emanating from product in whole or part, as
this may cause an unsafe condition.

• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.

• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body.

• Replace LED assembly only with correct wattage and type of
power supply appropriate for LED assembly.

• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.

Cap

Rings

LED Assembly

IMPORTANT LISTINGS AND CERTIFICATIONS

· Suitable for wet locations

Lens

Fixture Base

Mounting Plate

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF TEKA ILLUMINATION AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF TEKA ILLUMINATION AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF TEKA ILLUMINATION IS STRICTLY FORBIDDEN.

DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF TEKA ILLUMINATION IS STRICTLY FORBIDDEN.

40429 Brickyard Drive • Madera, CA 93636 • USA

www.tekaillumination.com • [e-mail]

559.438.5800 • FAX [phone]

DATE

2-8-17

REFERENCE NUMBER

INS-2566-00

APOLLO PILLAR™ (APL)

Phase 1 - Rough In

Installation of Back box

1. Install Conduit (By Others) to be used with
this product.

Phase 2 - Fixture Installation

Additional Info

• Please follow National and Local electrical codes for your area.

• Use 4” round cast box

• Suitable for through wire

• Suitable for installation into combustible materials.

• Rated for 90° C.

• Junction box, universal mounting ring screws, box mounting hardware
and gaskets (By Others)

Junction box must be secured to a structural member suitable for

weight of the luminaire and other weight likely to be placed upon it.

APL Series not intended for base down mounting.

2. Install junction box (By Others) so that front
face is flush with finished wall.

LINE

GROUND

COM

LINE

GROUND

COM

FIXTURE

3. Connect box to conduit and pull wires for
connections (See wiring diagram).

1. Loosen two (2) 1/4-20 1/2” socket stainless steel
cone point set screws using a 1/8” Allen wrench. Lift
fixture assembly from base plate assembly.

4. Place a bead of silicone-based sealant (By Others)
around the mounted plate to create a watertight seal.
Seal any unused hole(s) in mounting plate.

WIRING DIAGRAM

2. Connect primary branch circuit wiring to fixture
leads using watertight wire connectors (By
Others) as per NEC. Connect green fixture wire
to green supply wire. See wiring diagram.

5. Slide fixture assembly over mounted base plate

assembly. Lock in place with two (2) 1/4-20 1/2”
socket stainless steel cone point set screws
using a 1/8” Allen wrench. Ensure fixture is
completely seated.

3. Place connections inside junction box, then
attach base plate assembly to junction box
using mounting hardware (By Others).

APL Series not intended for base down

mounting.

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

40429 Brickyard Drive • Madera, CA 93636 • USA

www.tekaillumination.com • [e-mail]

559.438.5800 • FAX [phone]

DATE

2-8-17

REFERENCE NUMBER

INS-2566-00