Page 1
Dual 10 Band Equalizer
EQ5300
Page 2
Congratulations and thank you for your purchase of this Technical Pro Professional Dual 10 Band Equalizer, the EQ5300. To get the most
from your EQ5300, it is recommended that you review all of the information provided in this instruction manual before operating this
equipment.
If you've spent any time at all in professional audio, you know the name Technical Pro and what it stands for — incredible performance &
sound, and the ultimate in reliability under harsh conditions. And now, Technical Pro offers the same technology in a series of
professional
equalizers
bringing more of what sets Technical Pro apart from all others.
1- Read these instructions thoroughly before using this item.
2- Keep these instructions for future reference.
3- Heed all warnings.
4- Follow all instructions.
5- WARNING: To prevent fire or electric shock, do not expose this equipment to rain or moisture. Do not store or operate this
product near any liquids.
6- Clean only with a dry cloth.
7- Do not store or operate this product near any heat sources such as radiators, heat registers, stoves, or other apparatuses
(including amplifiers) that produce heat.
8- Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than
the other. A grounding plug has two blades and a round grounding prong. The wide blade or third prong is provided for your safety.
If the provided plug does not fit your outlet, consult an electrician for the replacement of the obsolete outlet.
9- Protect the all wires connected to this unit from being walked on or pinched, particularly plugs and the point where they exit from
the unit. When removing the cord from the power outlet, remove it by holding the plug not by pulling the cord.
10- Unplug the unit during lightning storms or when unused for long periods of time.
11- When wiring this unit and all other equipment used in connection to this unit make sure that all of your equipment is turned OFF.
12- Once installation and wiring is complete power on all your equipment with the volume and level controls turned DOWN. Once
all the equipment is ON slowly raise the volume or level controls to their proper positions.
13- When grounding this unit, be sure to do so correctly, so as not to defeat the built-in grounding in this unit.
14- Before placing, installing, rigging, or suspending any product, inspect all hardware, suspension, cabinets, transducers,brackets
and associated equipment for damage. Any missing, corroded, deformed, or non-load rated component could significantly reduce
the strength of the installation, placement or array. Any such condition severely reduces the safety of the installation and should be
immediately corrected. Use only hardware which is rated for the loading conditions of the installation and any possible short-term,
unexpected overloading. Never exceed the rating of the hardware or equipment.
15- Consult a licensed, Professional Engineer regarding physical equipment installation. Ensure that all local, state and national
regulations regarding the safety and operation of equipment are understood and adhered to.
16- Refer all servicing to qualifie nel. Servicing is required when the apparatus has been damaged in any way,
such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped.
WARNING!
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER OF THIS UNIT. THERE
ARE NOUSER-SERVICEABLE PARTS INSIDE. REFER ALL SERVICING TO A QUALIFIED TECHNICIAN.
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence
of "dangerous" voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of
electric shock to humans. Users should exhibit extra safety when this symbol appears in this instruction manual and
follow all precautions as they are stated.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in this manual.
Introduction
EQ5300
Page 3
1.LED: Press this button to power the LEDs of the sliders on and off.
2.Input:
Press this button to switch among all the input modes. The default input is TAPE input mode.
3.
EQ/BYPASS: Press this button to disable the EQ effect on the EQ5300. Press it again to activate.
When the EQ effect is activated, the signal passing through the EQ5300 will be changed depending on
the position of the EQ sliders.
4.Range
: Press this button to increase the signal by ±6dB or ±12dB. The default setting is ±6dB.
5.
Display: Press this button to switch the screen display among all the display modes.
6.Power
: Press this button to power the unit on and off.
7.High/Low
: Press this button to select spectrum display mode.
8.
Dual 10 Band Equalizers: Use the sliders to increase or decrease the respective frequencies. The
equalization points are 30Hz,64Hz,125Hz,250Hz,500Hz,1KHz,2KHz,4KHz,8KHz and16KHz. The
adjustment range is ±12dB.
EQ5300 Front Panel
134 267 5
8
EQ5300
Page 4
EQ5300 Rear Panel
1.Power Supply: Use the power cord to provide with the unit. Before connecting it to the outlet, be sure the
power of the EQ5300 is off.
2.Voltage Selector: Select between 230V AC 50Hz / 115V AC 65Hz.
3.LINE Output:Connect the line output to the input on either a recording device or another amplifier. The
signal from the line output is a passive output and can not be connected directly to a passive speaker.
4.REC Output: Connect the REC output to the input on either a recording device or another amplifier. The
signal from the REC output is a passive output and can not be connected directly to a passive speaker.
5.Tuner Input: Connect any stereo signal such as a DVD,CD,TAPE,Mixer etc to this input. To play a signal
connected to this input make sure the tuner input is selected on the front panel.
6.VCD/CD Input: Connect any stereo signal such as a DVD, CD, TAPE, Mixer etc to this input. To play a
signal connected to this input make sure the DVD input is selected on the front panel.
7.Tape Input: Connect any stereo signal such as a DVD, CD, TAPE, Mixer etc to this input. To play a signal
connected to this input make sure the tape input is selected on the front panel.
1234567
EQ5300
Page 5
Typical EQ5300 Input and Output Connections
In the typical setup, a user should wire from the output of the signal source directly to one of the RCA
inputs on the rear of the EQ5300. Once the input signal source is connected to the EQ5300, connect
the amplifier to the EQ5300’s LINE outputs. Pictured above is a TV and DVD player connected to the
EQ5300’s inputs. The REC output is connected to the input of a tape recorder. The LINE output of
EQ5300 is connected to the input of another amplifier. You can bypass the tape recorder and just
connect the LINEOUTPUT to the input of another amplifier. The LINE OUTPUT will send the signal
from the selected input (AUX,DVD,Tape,Tuner
or MP3 Player).
NOTE:WHEN MAKING THESE CONNECTIONS THE POWER OF THE E5300 AND THE SIGNAL
SOURCE SHOULD ALL BE IN THE OFF POSITION
EQ5300
Aduio Input
Power Outlet
(AUDIO OUTPUT)
TV
(AUDIO OUTPUT)
o
(AUDIO INPUT)
Page 6
Input / Output Connections
The EQ5300 has three input jacks on the rear of the unit which is designed to receive the signal directly
from your DVD, mixer or any of your other 2 Channel signal sources. To ensure that you have correctly
connected your DVD player (other sound sources) to the unit ,make sure that the DVD player has a
RCA cord coming from it’s output and that this cord is plugging into the RCA Input on the rear of the
EQ5300. Ensure that the polarity of your signal is always maintained by using color coordinated RCA
cables.
NOTE: BE SURE NOT TO CONNECT AN AMPLIFIER OR ANY AMPLIFIED SIGNAL INTO THE RCA
INPUT JACK. AS THIS COULD DAMAGE THE EQ5300. ALWAYS MAKE SURE THAT THERE IS NO
AMPLIFIER BEFORE EQ5300.
Connecting the Signal Source to the EQ5300 (DVD/MIXER/MP3 etc.)
There are two output jacks on the rear of the unit. The active speakers should be connected via the
speaker wire outputs on the rear of the EQ5300.
Connecting the EQ5300 to Active Loudspeakers
NOTE:
THE SIGNAL FROM THE REC OUTPUT IS A PASSIVE OUTPUT AND CAN NOT BE CONNECTED
DIRECTLY TO A PASSIVE SPEAKER.
EQ5300
Loading...