Technical Pro Powered Bluetooth Speaker System
User Manual
MODEL: BLUET32LG
BLUET32LG
WARNING!
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER ON THIS SPEAKER. THERE ARE NO USER-
SERVICEABLE PARTS INSIDE. REFER ALL SERVICING TO A QUALIFIED TECHNICIAN
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of "dangerous"
voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to humans. Users
should exhibit extra safety when this symbol appears in this instruction manual and follow all precautions as they are stated.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and
maintenance (servicing) instructions in this manual.
1- Read these instructions thoroughly before using this item.
2- Keep these instructions for future reference.
3- Heed all warnings.
4- Follow all instructions.
5- WARNING: To prevent fire or electric shock, do not expose this equipment to rain or moisture. Do not store or operate this
product near any liquids.
6- Clean only with a dry cloth.
7- Do not store or operate this product near any heat sources such as radiators, heat registers, stoves, or other apparatuses
(including amplifiers) that produce heat.
8- Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the
other. A grounding plug has two blades and a round grounding prong. The wide blade or third prong is provided for your safety. If
the provided plug does not fit your outlet, consult an electrician for the replacement of the obsolete outlet.
9- Protect the all wires connected to this unit from being walked on or pinched, particularly plugs and the point where they exit from
the unit. When removing the cord from the power outlet, remove it by holding the plug not by pulling the cord.
10- Unplug the unit during lightning storms or when unused for long periods of time.
11- When wiring this unit and all other equipment used in connection to this unit make sure that all of your equipment is turned OFF.
12- Once installation and wiring is complete power on all your equipment with the volume and level controls turned DOWN. Once all
the equipment is ON slowly raise the volume or level controls to their proper positions.
13- When grounding this unit, be sure to do so correctly, so as not to defeat the built-in grounding in this unit.
14- Before placing, installing, rigging, or suspending any product, inspect all hardware, suspension, cabinets, transducers, brackets
and associated equipment for damage. Any missing, corroded, deformed, or non-load rated component could significantly reduce
the strength of the installation, placement or array. Any such condition severely reduces the safety of the installation and should be
immediately corrected. Use only hardware which is rated for the loading conditions of the installation and any possible short-term,
unexpected overloading. Never exceed the rating of the hardware or equipment.
15- Consult a licensed, Professional Engineer regarding physical equipment installation. Ensure that all local, state and national
regulations regarding the safety and operation of equipment are understood and adhered to.
16- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such
as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
Introduction
Congratulations and thank you for your purchase of this Technical Pro Powered Bluetooth Speaker System, the BLUET32LG.
To get the most from your BLUET32LG, it is recommended that you review all of the information provided in this instruction
manual before operating this equipment.
If you've spent any time at all in professional audio, you know the name Technical Pro and what it stands for — incredible
performance & sound, and the ultimate in reliability under harsh conditions. And now, Technical Pro offers the same
technology in a series of power loudspeakers bringing more of what sets Technical Pro apart from all others.
P-1
BLUET32LG
BLUET32LG Rear Panel:
1. Power Supply: Connect the power cord here. The power switch should be set to the off position before the
power supply is connected.
2.Voltage selector: Select between 110V AC 60Hz / 220V AC 50Hz. When using with a 110V outlet, the unit should
be set to 110V.
3. Right Satellite Speaker Connector: Connect one of the satellite speakers to this output.
4. Left Satellite Speaker Connector: Connect one of the satellite speakers to this output.
5. AUX Line Input (RCA): Connect your sound source to this RCA input. The line volume will be controlled by
the volume knob located on the front panel of the unit. Only passive signals should be connected to this
input.
P-2
BLUET32LG
BLUET32LG Front Panel:
6. Left Satellite Speaker: Connect this speaker to the left satellite speaker output on the rear on the base unit
of the BLUET32LG.
7. Light Globe Power Switch: Press this button to power on / off the top mounted light globe.
8. Power Switch: Before the unit is powered on, all of the level controls should be turned down all the way.
Once powered on, slowly begin to raise the levels of the inputs. This will prevent damaging both the speaker
and the amplifier.
9. Master Volume: Turn this knob to increase or decrease the master volume.
10. Right Satellite Speaker: Connect this speaker to the right satellite speaker output on the rear on the base
unit of the BLUET32LG.
11. Input Selector: Use this button to switch between all the inputs.
12. Play / Pause Button: When the input selected is USB/SD/Bluetooth, press this button to pause the signal from
the USB flash drive, SD card, Bluetooth connected to the USB input. Press this button again to play. The
play/pause function will only work for the USB flash drive, SD card or Bluetooth inputs.
13. Previous Track Button: Press this button to go back to the beginning of the previous track on either the USB
flash drive, SD Card or Bluetooth inputs. Press and hold down this button to decrease the volume.
14. Next Track Button: Press this button to go back to the beginning of the next track on either the USB flash
drive, SD Card or Bluetooth inputs. Press and hold down this button to increase the volume.
15. EQ Mode Selector: When playing from the USB flash drive, SD Card or Bluetooth Inputs press this button to
switch among the pre-set equalization modes.
16. AUX (1/8”) Input: Connect your MP3 player or computer here. Make sure to press the input selector button (11)
until the unit is set to the AUX input.
17. SD Card Input: Insert your SD card into this slot. The unit will only read .mp3 & .wma files from SD card. The
maximum storage size of the SD card cannot exceed 16GB. Make sure to set the input is set to USB / SD.
18. USB Input: Insert your USB flash drive into this slot. The unit will only read .mp3 & .wma files from the USB
flash drive. The maximum storage size of the USB flash drive cannot exceed 16GB. Make sure to set the input is
set to USB / SD.
19. Input Indicator: See details on following page.
P-3
BLUET32LG
BLUET32LG Operation:
Using the AUX (RCA) Input:
to the speaker outputs on the rear of the base unit. Connect the AUX source to either the RCA inputs on the
rear of the unit or the 1/8” input on the front panel. Power the unit on. Press the input button until the input
indicator (19) illuminates SOLID green. Begin to play your audio and slowly raise the volume to the desired
levels.
Using the USB Flash Drive / SD Card Input:
satellite speakers to the speaker outputs on the rear of the base unit. Connect the USB flash drive or SD
Card to the inputs on the front panel of the base unit. Power the unit on. Press the input button until the
input indicator (19) illuminates FLASHING green. Using the controls on the front panel play the audio from
the USB flash drive / SD Card and slowly raise the volume to the desired levels.
Using the Bluetooth Input: Power off the BLUET32LG and lower the volume. Connect the satellite speakers
to the speaker outputs on the rear of the base unit. Power the unit on. Press the input button until the input
indicator (19) illuminates blue. Open the Bluetooth device’s Bluetooth connections and search for Bluetooth
enabled devices. The Bluetooth device should be able to locate a device named “BLUET32LG”. Select this
device and connect to it. The unit will then beep indicating that the unit has successfully paired with the
Bluetooth device. Play music directly on the BLUET32LG directly from the Bluetooth device. Slowly raise the
volume to the desired levels.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Federal Communications Commission Requirements:
The equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction, may cause harmful interference to radio communication. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
● Consult the dealer or an experienced radio/TV technician for help.
THE CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE
COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
FCC Radiation Exposure Statement
The equipment complies with FCC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency
(RF) Exposure Guidelines in Supplement C to OET65. The equipment has very low levels of RF energy that it is deemed to comply
without testing of specific absorption ratio (SAR).
The Bluetooth word mark and logos are registered trademarks owned by SIG, Inc. and any use of such marks by Technical Pro is under
license. Other trademarks and trade name are those of their respective owners.
Power off the BLUET32LG and lower the volume. Connect the satellite speakers
Power off the BLUET32LG and lower the volume. Connect the
P-4
BLUET32LG
BLUET32LG Remote:
1. USB / SD / Bluetooth Power Button: Press this button to turn on and off the USB/SD/Bluetooth module on
the rear of the unit.
2. Input Selector: Use this button to switch between all the inputs.
3. Mute
4. Previous Track Button: Press this button to go back to the beginning of the previous track on either the USB
flash drive or SD Card input. Press and hold down this button to decrease the volume.
Next Track Button: Press this button to go back to the beginning of the next track on either the USB flash
drive or SD Card input. Press and hold down this button to increase the volume.
5. Master Volume: Press these buttons to increase or decrease the master volume.
6. Number Keys: The number keys are used to input the track number when using the USB / SD Card inputs. For
example if you press 9, the unit will go to track number 9 on either the USB flash drive, SD Card. If you press 1
then 9 the unit will go to track 19.
7. Play / Pause: Press this button to pause the signal from the USB flash drive, SD Card, press again to play.
8. EQ Mode Selector: The unit has five built-in pre-set equalization modes. Press this button to switch among the
pre-set equalization modes when using the USB or SD Card inputs.
9. Repeat Control: Press this button to repeat the current track, all tracks on the USB flash drive, SD Card.
10. USB / SD Card Mode Selector: Press this button to switch between the USB flash drive input and SD
Card input.
P-5
Loading...