Techne DB200-3 User Manual

DB100/2, DB100/3, DB100/4,

DB100/2TC,

DB200/2, DB200/3

Dri-Block® Heaters

OPERATOR’S MANUAL

Issue 7
06/2014
Part code: 6106451

2

CONTENTS

INTRODUCTION ........................................................................................................ 5

BEFORE USE............................................................................................................. 6

Unpacking .................................................................................................................................................6

SAFETY AND INSTALLATION .................................................................................. 7

Warning ....................................................................................................................................................7

Operator Safety ........................................................................................................................................7

Installation ................................................................................................................................................7

Environmental Conditions ........................................................................................................................8

Guarantee .................................................................................................................................................8

SÉCURITÉ ET CONSIGNES D’INSTALLATION ....................................................... 9

Avertissement ...........................................................................................................................................9

Sécurité de l’opérateur .............................................................................................................................9

Installation ................................................................................................................................................9

Conditions environnementales .............................................................................................................. 10

Garantie ................................................................................................................................................. 10

SICHERHEITS- UND INSTALLATIONSINFORMATIONEN .................................... 11

Achtung ................................................................................................................................................. 11

Sicherheit des Bedienpersonals ............................................................................................................ 11

Inbetriebnahme...................................................................................................................................... 11

Umweltbedingungen .............................................................................................................................. 12

Garantie ................................................................................................................................................. 12

INFORMAZIONI SULLA SICUREZZA E L'INSTALLAZIONE ................................. 13

Avvertenza ............................................................................................................................................. 13

Sicurezza dell'operatore ........................................................................................................................ 13

Installazione ........................................................................................................................................... 13

Condizioni ambientali ............................................................................................................................ 14

Garanzia ................................................................................................................................................ 14

INFORMACIÓN DE SEGURIDAD E INSTALACIÓN ............................................... 15

Advertencia ............................................................................................................................................ 15

Seguridad del operario .......................................................................................................................... 15

Instalación ............................................................................................................................................. 15

Condiciones ambientales ...................................................................................................................... 16

Garantía ................................................................................................................................................. 16

CONTACT INFORMATION ...................................................................................... 17

SPECIFICATIONS .................................................................................................... 18

DB100/2, DB100/3 and DB100/4 .......................................................................................................... 18

DB200/2 and DB200/3 .......................................................................................................................... 19

DB100/2TC ............................................................................................................................................ 20

OPERATION ............................................................................................................ 21

Installation ............................................................................................................................................. 21

Power up screen.................................................................................................................................... 22

The front panel controls ......................................................................................................................... 22

Setting the temperature units ................................................................................................................ 23

Setting the operating temperature ......................................................................................................... 23

Setting the timer .................................................................................................................................... 23

After use ................................................................................................................................................ 24

User maintenance ................................................................................................................................. 24

Calibration ............................................................................................................................................. 25

ADDITIONAL INFORMATION.................................................................................. 26

Fault Finding .......................................................................................................................................... 26

Fuses ..................................................................................................................................................... 26

Safety over-temperature cut-out............................................................................................................ 26

Support contacts.................................................................................................................................... 27

3

ACCESSORIES ........................................................................................................ 28

REPLACEMENT PARTS .......................................................................................... 29

DECLARATION OF CONFORMITY ......................................................................... 30

4

INTRODUCTION

Voltage,

Please read all the information in this manual before using the unit.

Techne Dri-Block® heaters provide a safe, dry, constant temperature source in the laboratory. The
units can be used for incubation, boiling, inactivation, wet ashing, sample concentration, enzyme
analysis and many other clinical and industrial purposes.

The units cover the temperature range from ambient +5°C to 100°C or 200°C (depending on model)
using machined aluminium alloy blocks as the heat transfer medium. Independent indicator lights
indicate mains power, heater action and over-temperature cut-out. An ON/OFF switch is mounted on
the rear panel, together with the mains connector and a double fuse holder.

Temperature setting is via a simple push button display. Temperatures can be displayed in °C or °F.
Each unit also has a built-in count-down timer which can be set in 1 minute intervals to 99h 59m.

The units are constructed of painted aluminium alloy and polyphenylene sulphide (PPS) plastic,
which is strong yet lightweight and can resist sustained temperatures as high as 260°C. Even though
the units heat up rapidly, venting and highly efficient insulation ensure that the cases remain cool
enough to handle even at maximum operating temperatures.

Each unit is supplied with an extraction tool for easy removal of the insert blocks.

The operating instructions in this Operator’s Manual cover the following range of digital Dri-Block®
heaters:

Model number Description

DB100/2 Dri-Block® heater ambient to 100°C, accepts 2 insert blocks 230V, 50-60Hz

DB100/2/115 Dri-Block® heater ambient to 100°C, accepts 2 insert blocks 115V, 50-60Hz

DB100/3

DB100/3/115

DB100/4

DB100/4/115

DB100/2TC

DB100/2TC/115

DB200/2

DB200/2/115

DB200/3

DB200/3/115

The features of individual models are outlined in the Specifications section of this manual.

Note: This manual covers the digital Dri-Block® heater range. The analogue Dri-Block® heaters DB-2A,
DB-3 and DB-3A are covered in a separate user manual.

Dri-Block® heater ambient to 100°C, accepts 3 insert blocks 230V, 50-60Hz

Dri-Block® heater ambient to 100°C, accepts 3 insert blocks 115V, 50-60Hz

Dri-Block® heater ambient to 100°C, accepts 4 insert blocks 230V, 50-60Hz

Dri-Block® heater ambient to 100°C, accepts 4 insert blocks 115V, 50-60Hz
Dri-Block® heater ambient to 100°C, accepts 2 insert blocks,

twin control
Dri-Block® heater ambient to 100°C, accepts 2 insert blocks,

twin control
Dri-Block® heater ambient to 200°C, accepts 2 insert blocks 230V, 50-60Hz

Dri-Block® heater ambient to 200°C, accepts 2 insert blocks 230V, 50-60Hz

Dri-Block® heater ambient to 200°C, accepts 3 insert blocks 230V, 50-60Hz

Dri-Block® heater ambient to 200°C, accepts 3 insert blocks 115V, 50-60Hz

frequency

230V, 50-60Hz

115V, 50-60Hz

5

BEFORE USE

Before using the Dri-Block® heater please make sure you have read this manual carefully. If there is
any doubt relating to the proper use of this equipment, the staff at Bibby Scientific Ltd. or your
supplier will be happy to assist you.

UNPACKING

When unpacking the unit please ensure that the following have been removed from the packaging:

• Dri-Block® heater

• 6101308 Extraction tool

• Mains cables (UK and EU or US)

• Operator’s manual

• Guarantee card

The user is advised to keep the original packaging in case the instrument ever needs to be returned
for service or repair. Bibby Scientific Ltd. accepts no responsibility for damage incurred unless the
unit is correctly packed and transported in its original packaging.

The Dri-Block® heater range

6

SAFETY AND INSTALLATION

Connection

s 230V

, 50/60Hz

115V

, 50/60Hz

Live Brown

Black

Neutral

Blue White

Earth

Green/yellow

Green

Please read all the information in this manual before using the Dri-Block® heater.

WARNING

HIGH TEMPERATURES ARE DANGEROUS: they can cause serious burns to operators and ignite
combustible material.

Techne have taken great care in the design of these units to protect operators from hazards, but
operators should pay attention to the following points:

• USE CARE AND WEAR PROTECTIVE GLOVES TO PROTECT HANDS

• DO NOT use combustible substances near hot objects

• DO NOT operate the instrument in the vicinity of inflammable liquids or gases.

• DO NOT place any liquid directly into the instrument.

OPERATOR SAFETY

All operators of Techne equipment must have available the relevant literature needed to ensure their
safety. It is important that only suitably trained personnel operate this equipment, in accordance with
the instructions contained in this manual and with general safety standards and procedures. If the
equipment is used in a manner not specified by Bibby Scientific Ltd. the protection provided by the
equipment to the operator may be impaired.

All Techne instruments are designed to conform to international safety requirements and are fitted
with an over-temperature cut-out.

If a safety problem should be encountered, switch off the unit at the mains socket and remove the
plug from the electricity supply.

INSTALLATION

The instrument should be carried using both hands. Never move or carry the instrument when in use
or connected to the mains electricity supply.

1. All Techne instruments are supplied with a power cable; this may be integral or plug-in.

2. Before connecting the instrument to the mains electricity supply, check the voltage
against the rating plate (located on the back of the unit). Please note that the unit
must be earthed to ensure proper electrical safety. Connect the mains cable to a
suitable plug according to the table below.

UK ONLY: The fused plug supplied with the mains cable is fitted with a 5 amp fuse to protect the
instrument and the operator.

Note that units marked 230V on the rating plate work at 207V; units marked 115V work at 104V. In
both cases, however, the heating rate will degrade by approximately 8%.

3. Place the unit on a suitable flat bench or in a fume cupboard if required, ensuring that the air inlet

vents on the underside are free from obstruction.

4. Plug the mains cable into the socket on the back of the instrument.

5. Switch on the instrument. Symbols on or near the power switch of the unit have the following

meanings:

7

I Mains Switch On
O Mains Switch Off

Replacement cable

Should the mains lead need replacement, a cable of 1mm2 of harmonized code H05VV-F connected
to an IEC320 plug should be used. IF IN DOUBT CONSULT A QUALIFIED ELECTRICIAN.

ENVIRONMENTAL CONDITIONS

The Dri-Block® heater is designed operate under the following conditions:

• Indoor use

• Ambient temperature range +5ºC to +40ºC

• Altitude to 2000m

• Relative humidity up to 80%

• Mains supply fluctuations not exceeding 10%

• Over voltage category II IEC 60364-4-443

• Pollution degree 2

• Use with a minimum distance all-around of 200mm from walls or other items

Note: The control specifications are quoted at an ambient temperature of 20ºC. The specification
may deteriorate outside an ambient temperature of between 10ºC and 30ºC.

The instrument has been tested for radio frequency interference and is certified under EN61326.

GUARANTEE

The instrument is guaranteed against any defect in material or workmanship for the period specified
on the enclosed guarantee card. This period is effective from the date of purchase; within this period
all defective parts will be replaced free of charge provided that the defect is not the result of an
accident, misuse or negligence. Servicing under this guarantee should be obtained from the supplier
of the instrument.

This manual has been prepared for the convenience of Techne’s customers and nothing in this
manual shall be taken as a warranty, condition or representation concerning the description,
merchantability, fitness for purpose or otherwise of the unit or components.

Notwithstanding the description and specification(s) of the instruments contained in the operator’s
manual, Techne reserves the right to make such changes as it sees fit to the instruments or to any of
the components.

8

SÉCURITÉ ET CONSIGNES D’INSTALLATION

Connexion

s 230V

, 50/60

Hz 115V

,

50/60

Hz

Phase

Marron

Noir

Neutre

Bleu Blanc

Terre

Vert/jaune

Vert

Veuillez lire attentivement toutes les instructions de ce document avant d’utiliser le Dri-Block® heater.

AVERTISSEMENT

Les TEMPÉRATURES ÉLEVÉES SONT DANGEREUSES car elles peuvent provoquer de graves
brûlures chez l’opérateur et enflammer les matériaux combustibles.

Techne a apporté un soin tout particulier à la conception de ces appareils de façon à assurer une
protection maximale des opérateurs, mais il est recommandé aux utilisateurs de porter une attention
spéciale aux points suivants :

• PROCEDER AVEC PRUDENCE ET PORTER DES GANTS POUR SE
PROTEGER LES MAINS

• NE PAS utiliser de matériaux combustibles auprès d’objets chauds.

• NE PAS utiliser l’appareil à proximité de liquides ou de gaz inflammables

• NE PAS verser de liquides directement dans l’appareil.

SECURITE DE L’OPÉRATEUR

Tous les utilisateurs de produits Techne doivent avoir pris connaissance des consignes et instructions
nécessaires à la garantie de leur sécurité. Important: cet appareil doit impérativement être manipulé
par un personnel qualifié et être utilisé selon les instructions données dans ce document, en accord
avec les normes et procédures de sécurité générales. Dans le cas où cet appareil ne serait pas utilisé
selon les consignes précisées par Bibby Scientific Ltd., la protection pour l’utilisateur ne serait alors
plus garantie.

Tous les appareils Techne sont conçus pour répondre aux normes de sécurité internationales et sont
dotés d’un coupe-circuit en cas de surchauffe.

En cas de problème de sécurité, couper l’alimentation électrique au niveau de la prise murale et
enlevez la prise connectée à l’appareil.

INSTALLATION

Porter l'appareil à deux mains. Ne jamais déplacer ou transporter l’appareil lorsqu’il est en
fonctionnement ou branché à l’alimentation électrique.

1. Tous les appareils Techne sont livrés avec un câble d'alimentation, qui peut être intégré à l'appareil
ou à raccorder.

2. Avant de raccorder l’appareil à l’alimentation électrique sur secteur, vérifier la tension

requise indiquée sur la plaque d’identification (située au dos de l’appareil). Il est

important que l’appareil soit relié à la terre pour assurer la protection électrique
requise. Brancher le câble secteur sur une prise appropriée, voir tableau ci-après.

ROYAUME-UNI SEULEMENT: La prise avec fusible intégré fournie avec le câble secteur est
munie d’un fusible 5 A destiné à protéger l’appareil et l’utilisateur.

Remarque : les appareils dont la plaque indique 230 V peuvent fonctionner sur 207 V, et ceux dont
la plaque indique 115 V peuvent fonctionner sur 104 V. Dans les deux cas cependant, la capacité
de chauffage diminuera d’environ 8 %.

9

3. Placer l’appareil sur une surface plane ou si nécessaire sous une hotte d’aspiration, veiller à ce
que les trous d’aération situés sous l’appareil ne soient pas obstrués.

4. Raccorder le câble d’alimentation à la prise située à l’arrière de l’appareil.

5. Allumer l'appareil. Les symboles situés sur ou à côté de l’interrupteur de l’appareil ont la
signification suivante :

I Interrupteur secteur en position Marche
O Interrupteur secteur en position Arrêt

Câble de rechange

S’il s’avère nécessaire de remplacer le cordon d’alimentation, utiliser un câble de 1 mm² conforme à
la norme H05VV-F relié à une prise IEC320. EN CAS DE DOUTE, CONSULTER UN ELECTRICIEN

QUALIFIE.

CONDITIONS ENVIRONNEMENTALES

Le Dri-Block® heater est conçu pour fonctionner dans les conditions suivantes:

• Pour un usage intérieur seulement

• Température ambiante +5°C à +40°C

• Altitude inférieure à 2000m

• Humidité relative ne dépassant pas 80%

• Fluctuations de l’alimentation n’excédant pas 10% de la valeur nominale

• Catégorie II IEC 60364-4-443 de surtension

• Degré de pollution 2

• Utiliser à une distance minimale sur le pourtour de 200mm par rapport aux murs et autres

équipements

Remarque: Les paramètres sont indiqués pour une température ambiante de 20°C. Ces
caractéristiques peuvent se détériorer en dehors d’une température ambiante de 10 à 30°C.

L’appareil a été testé en matière de radiofréquences et est certifié selon la norme EN61326.

GARANTIE

L’appareil est garanti contre tout défaut de matériaux ou vice de fabrication pendant la période
précisée sur la carte de garantie jointe. Cette période s’applique à compter de la date d’achat. Au
cours de cette période, toutes les pièces défectueuses seront remplacées gratuitement dans la
mesure où la défaillance n’est pas due à un accident, une mauvaise utilisation ou une négligence.
Toute réparation sous garantie sera effectuée par le fournisseur.

Le présent manuel a été exclusivement rédigé à l’attention des clients de la marque Techne et rien
dans son contenu ne doit être pris comme une garantie, une condition ou une affirmation concernant
la description, la commercialisation, l’adéquation à un usage particulier de l'appareil ou de ses
composants.

Malgré la description et les caractéristiques techniques des appareils données dans le manuel de
l’utilisateur, la société Techne se réserve le droit d’apporter les changements nécessaires à l’appareil
ou à tout élément qui entre dans sa composition.

10

SICHERHEITS- UND INSTALLATIONSINFORMATIONEN

Anschluss

230V

, 50/60Hz

115V

, 50/60Hz

Phase

Braun

Schwarz

Neutral

Blau Weiß

Erde

Grün/Gelb

Grün

Lesen Sie diese Anleitung vor Verwendung des Dri-Block® heater bitte sorgfältig durch.

ACHTUNG

HOHE TEMPERATUREN STELLEN EINE GEFAHRENQUELLE DAR. Sie können schwere
Brandverletzung verursachen und brennbare Stoffe entzünden.

Techne hat bei der Konstruktion dieses Gerätes sehr darauf geachtet, daß der Bediener vor
Gefahren geschützt ist. Dennoch sollten Sie auf die folgenden Punkte achten:

• UMSICHTIG VORGEHEN UND SCHUTZHANDSCHUHE TRAGEN

• KEINE brennbaren Stoffe in der Nähe heißer Gegenstände verwenden

• Das Gerät NICHT in der Nähe entzündlicher Flüssigkeiten oder Gase betreiben

• Flüssigkeiten NICHT direkt auf das Gerät auftragen.

SICHERHEIT DES BEDIENPERSONALS

Alle Benutzer von Techne Geräten müssen Zugang zu der entsprechenden Literatur haben, um ihre
Sicherheit zu gewähren. Es ist wichtig, daß diese Geräte nur von entsprechend geschultem Personal
betrieben werden, das die in dieser Gebrauchsanweisung enthaltenen Maßnahmen und allgemeine
Sicherheitsbestimmungen und - vorkehrungen beachtet. Wenn das Gerät anders eingesetzt wird als
vom Hersteller empfohlen, kann dies die persönliche Sicherheit des Anwenders beeinträchtigen.

Die Geräte von Techne entsprechen den internationalen Sicherheitsbestimmungen und sind mit einem
automatischen Übertemperaturabschalter ausgestattet.

Wenn ein Sicherheitsproblem auftreten sollte, muß das Gerät ausgeschaltet und vom Stromnetz
getrennt werden.

INBETRIEBNAHME

Das Gerät mit beiden Händen tragen. Das Gerät unter keinen Umständen transportieren, wenn es in
Betrieb ist, oder während das Gerät noch am Netz angeschlossen ist.

1. Alle Geräte von Techne werden mit einem Netzkabel geliefert, das entweder eingesteckt wird
oder fest mit dem Gerät verbunden ist.

2. Vor dem Anschluss bitte kontrollieren, ob die Stromversorgung den Angaben auf dem

Typenschild (auf der Geräterückseite) entspricht. Um die elektrische Sicherheit zu
gewährleisten, muss dieses Gerät geerdet werden. Schließen Sie das Netzkabel
entsprechend der folgenden Tabelle an einen geeigneten Stecker an.

NUR FÜR GROSSBRITANNIEN: der mit dem Netzkabel gelieferte Sicherungsstecker enthält
eine 5 Amp. Sicherung zum Schutz des Geräts und des Anwenders.

Geräte, die für 230 Volt ausgelegt sind, können auch bei 207 Volt arbeiten, Geräte für 115 Volt
auch bei 104 Volt. In beiden Fällen verringert sich die Aufheizrate um ca. 8%.

3. Stellen Sie das Gerät auf einen geeigneten ebenen Tisch oder in einem Abzugsschrank auf und
sorgen Sie dafür, dass die Lufteinlassschlitze auf der Geräteunterseite nicht blockiert sind.

4. Stecken Sie das Netzkabel in die Buchse auf der Geräterückseite ein.

5. Schalten Sie das Gerät ein:

11

I Netzschalter Ein

muss

O Netzschalter Aus

Ersatzkabel

Bei einem eventuellen Austausch des Netzkabels wird ein Kabel vom Typ H05VV-F mit 1 mm2
Adernquerschnitt und Europastecker (IEC 320) benötigt. IM ZWEIFELSFALL EINEN ELEKTRO-

FACHMANN HINZUZIEHEN.

UMWELTBEDINGUNGEN

Der Dri-Block® heater ist für den Einsatz unter folgenden Bedingungen ausgelegt:

• Gebrauch in Innenräumen

• Umgebungstemperatur zwischen +5ºC to +40ºC

• Höhe: bis zu 2000 m

• Relative Feuchte nicht über 80%

• Netzspannungsschwankungen nicht über 10%

• Überspannungsklasse 2 IEC 60364-4-443

• Verschmutzungsgrad 2

• Der Mindestabstand zwischen dem Gerät und umgebenden Wänden oder Gegenständen

200mm betragen

Hinweis: Die Gerätespezifikationen beziehen sich auf eine Umgebungstemperatur von 20ºC und
können sich außerhalb des Bereichs 10ºC bis 30ºC verschlechtern.

Das Gerät wurde auf HF-Störeinflüsse geprüft und entspricht den EMV-Bedingungen nach EN61326.

GARANTIE

Techne gewährleistet, dass dieses Gerät für den auf der Garantiekarte angegebenen Zeitraum keine
Herstellungs- und Materialmängel aufweist. Dieser Zeitraum tritt ab dem Verkaufsdatum in Kraft.
Innerhalb dieses Zeitraums werden alle defekten Teile kostenlos ausgetauscht, soweit der Defekt
nicht auf einen Unfall, Missbrauch oder Nachlässigkeit zurückzuführen ist. Wartungsarbeiten, die
unter diese Garantie fallen, müssen von der Verkaufsstelle für dieses Gerät gehandhabt werden.

Diese Anleitung wurde zur Information der Kunden von Techne erstellt und stellt in keinster Weise
eine Gewährleistung, Bedingung oder Darstellung bezüglich der Beschreibung, Marktgängigkeit oder
Zweckdienlichkeit dieser Geräte oder Bauteile dar.

Unabhängig von Beschreibung und Spezifikation(en) des hier beschriebenen Geräts behält sich
Techne das Recht vor, Änderungen an diesem Gerät oder dessen Bauteilen vorzunehmen.

12

INFORMAZIONI SULLA SICUREZZA E L'INSTALLAZIONE

Connessione

230V

, 50/60Hz

115V

,

50/60Hz

Sotto tensione

Marrone

Nero

Neutr

o Blu

Bianco

Terra

Verde/giallo

Verde

Leggere attentamente il presente manuale prima di usare il Dri-Block® heater.

AVVERTENZA

Le ALTE TEMPERATURE SONO PERICOLOSE in quanto possono provocare serie ustioni agli
operatori e dare fuoco al materiale combustibile.
La Techne ha posto particolare cura nel progettare questo strumento, al fine di proteggere gli
operatori da eventuali pericoli, ma gli utilizzatori devono prestare attenzione ai seguenti punti:

• PRESTARE ATTENZIONE ED INDOSSARE GUANTI PROTETTIVI PER LE
MANI

• NON usare sostanze combustibili vicino ad oggetti caldi

• NON mettere in funzione lo strumento nei pressi di liquidi o gas infiammabili

• NON collocare alcun tipo di liquido direttamente nello strumento.

SICUREZZA DELL'OPERATORE

Il personale che utilizza l’apparecchiatura Techne deve avere a disposizione la documentazione
necessaria al fine di assicurare la loro incolumità. È importante che solo personale adeguatamente
addestrato utilizzi questo apparecchio, in conformità alle istruzioni contenute in questo manuale e nel
rispetto delle normative e procedure generali di sicurezza. Se l’apparecchio è utilizzato in modo non
specificato da Bibby Scientific Ltd., la protezione fornita dall’apparecchiatura all’utilizzatore potrebbe
essere a rischio.

Tutte le unità Techne sono state progettate in conformità ai requisiti internazionali di sicurezza e sono
equipaggiate con un interruttore anti surriscaldamento.

Se si dovesse verificare qualche problema di sicurezza, disconnettere l’apparecchio dalla rete.

INSTALLAZIONE

Occorre trasportare lo strumento usando entrambe le mani. Non spostare né trasportare lo
strumento quando è in funzione o collegato all’alimentazione elettrica di rete.

1. Tutti gli strumenti Techne sono forniti con un cavo di alimentazione; può essere integrale o
plugin.

2. Prima di collegare lo strumento all'alimentazione elettrica di rete, controllare la

tensione confrontandola con la targhetta riportante i valori nominali (si trova sul retro
dell'unità). Notare che al fine di garantire la corretta sicurezza elettrica, occorre
che l'unità sia messa a terra. Collegare il cavo di rete ad una presa idonea secondo
la tabella riportata alla pagina successiva.

SOLO REGNO UNITO: la spina con fusibile fornita con il cavo di rete è dotata di un fusibile da 5
Amp per proteggere lo strumento e l'utente.

Tenere presente che gli apparecchi riportanti sulla targhetta 230 V funzionano a 207V. Gli
apparecchi riportanti 115V funzionano a 104V. Comunque, in entrambi i casi la velocità di
riscaldamento diminuirà approssimativamente dell’8%.

13

3. Collocare l'unità su un banco piano idoneo o in una cappa aspirante se necessario, assicurandosi
che gli sfiati delle prese d'aria nella parte inferiore non siano ostruiti.

4. Inserire il cavo di rete nella presa che si trova sul retro dello strumento.

5. Accendere lo strumento:

I Interruttore di rete Acceso
O Interruttore di rete Spento

Cavo di ricambio

Qualora occorra sostituire il cavo di rete, si dovrà utilizzare un cavo di 1mm2 codice armonizzato
H05VV-F collegato ad una spina IEC 320. IN CASO DI DUBBIO, RIVOLGERSI A UN

ELETTRICISTA QUALIFICATO.

CONDIZIONI AMBIENTALI

Il Dri-Block® heater è stato progettato per funzionare nelle seguenti condizioni:

• uso interno

• range di temperatura ambiente da +5ºC a +40ºC

• altitudine massima 2000 m.

• umidità relativa non superiore all’80%

• oscillazione dell’alimentazione di rete non superiore al 10%

• categoria di sovratensione II IEC 60364-4-443

• grado di inquinamento 2

• Con distanza minima tra i lati dell’apparecchio e il muro o altri oggetti di almeno 200mm

Nota: le specifiche di controllo sono indicate ad una temperatura ambiente di 20ºC. Le specifiche
potrebbero peggiorare fuori da una temperatura ambiente compresa tra 10ºC e 30ºC.

Lo strumento è stato collaudato per interferenze da radiofrequenze ed è certificato secondo la norma
EN61326.

GARANZIA

Lo strumento è garantito da qualsiasi difetto nei materiali o nella lavorazione per il periodo specificato
nella scheda di garanzia allegata. Questo periodo è valido dalla data di acquisto; entro tale periodo,
tutte le parti difettose saranno sostituite gratuitamente, a condizione che il difetto non sia la
conseguenza di un incidente, un uso improprio o negligenza. L'assistenza secondo quanto stabilito
dalla presente garanzia deve essere ottenuta dal fornitore dello strumento.

Il presente manuale è stato preparato ad uso dei clienti di Techne e niente di quanto in esso
contenuto costituisce garanzia, condizione o rappresentanza riguardo la descrizione, la
commerciabilità, l'idoneità allo scopo o altrimenti dell'unità o dei componenti.

Nonostante la descrizione e le specifiche dello strumento contenuti nel manuale dell'operatore,
Techne si riserva il diritto di apportare le modifiche ritenute opportune agli strumenti o a qualsiasi loro
componente.

14

INFORMACIÓN DE SEGURIDAD E INSTALACIÓN

Conexión

230V, 50/60Hz

115V

, 50/60Hz

Con corriente

Marrón

Negro

Neutro

Azul Blanco

Toma de tierra

Verde/amarillo

Verde

Lea atentamente este manual antes de utilizar el Dri-Block® heater.

ADVERTENCIA

LAS ALTAS TEMPERATURAS SON PELIGROSAS, ya que pueden ocasionar quemaduras graves a
los operarios y prender el material combustible. Techne ha puesto gran cuidado en el diseño de estos
aparatos para proteger al usuario de cualquier peligro; aún así se deberá prestar atención a los
siguientes puntos:

• TENGA CUIDADO Y LLEVE GUANTES DE PROTECCIÓN PARA
PROTEGERSE LAS MANOS

• NO utilice sustancias combustibles cerca de objetos calientes

• NO utilice el instrumento cerca de líquidos o gases inflamables

• NO coloque un líquido directamente en el instrumento.

SEGURIDAD DEL OPERARIO

Todos los usuarios de equipos Techne deben disponer de la información necesaria para asegurar su
seguridad. De acuerdo con las instrucciones contenidas en este manual y con las normas y
procedimientos generales de seguridad, es muy importante que sólo personal debidamente
capacitado opere estos aparatos. De no ser así, la protección que el equipo le proporciona al usuario
puede verse reducida.

Todos los equipos Techne han sido diseñados para cumplir con los requisitos internacionales de
seguridad y traen incorporados un sistema de desconexión en caso de sobre temperatura.

En caso de que surgiera un problema de seguridad, desconecte el equipo de la red.

INSTALACIÓN

El instrumento se debe transportar con las dos manos. No mueva ni lleve el instrumento cuando se
utilice o esté conectado al suministro eléctrico principal.

1. Todos los instrumentos Techne se suministran con un cable de alimentación, que puede ser
integrado o ‘enchufable’.

2. Antes de conectar el instrumento al suministro eléctrico, compruebe que el voltaje

coincida con el indicado en la placa de régimen (situada en la parte trasera de la
unidad). El instrumento debe disponer de una toma de tierra para garantizar la
seguridad eléctrica adecuada. Conecte el cable de alimentación a un enchufe
adecuado según la siguiente tabla.

SÓLO PARA EL REINO UNIDO: El enchufe suministrado con el cable de alimentación incluye
un fusible de 5 amperios para ofrecer protección al instrumento y al usuario.

Asegúrese de que los equipos marcados 230V en la placa indicadora funcionan a 207V y de
que los equipos marcados 115V funcionan a 104V. No obstante, en ambos casos la velocidad
de calentamiento se verá reducida en un 8% aproximadamente.

15

3. Sitúe la unidad sobre una mesa plana o en una campana de laboratorio si es necesario, y
asegúrese de que los orificios de ventilación situados en la parte inferior no tienen ninguna
obstrucción.

4. Conecte el cable de alimentación en el enchufe situado en la parte trasera del instrumento.

5. Encienda el instrumento:

O Interruptor de alimentación apagado

Cable de repuesto

Si es necesario sustituir el cable de alimentación, se debe utilizar un cable de 1mm2 de código
armonizado H05VV, conectado a un enchufe IEC320. EN CASO DE DUDA, PÓNGASE EN

CONTACTO CON UN ELECTRICISTA.

I Interruptor de alimentación encendido

CONDICIONES AMBIENTALES

El Dri-Block® heater está diseñado para utilizarse en las condiciones siguientes:

• Uso en interior

• Intervalo de temperatura ambiente +5ºC a +40ºC

• Altitud: hasta 2000 m

• Humedad relativa no superior al 80%

• Fluctuaciones del suministro eléctrico no superiores al 10%

• Categoría de sobrevoltaje II IEC 60364-4-443

• Nivel de contaminación 2

• Separado de paredes u otros objetos a una distancia mínima de 200mm

Nota: Las especificaciones de control corresponden a una temperatura ambiental de 20ºC. Las
especificaciones pueden empeorar si se utiliza el instrumento fuera del intervalo de temperatura
comprendido entre 10ºC y 30ºC.

Se han realizado pruebas para comprobar la interferencia de radiofrecuencia del instrumento, el cual
cumple la normativa EN61326.

GARANTÍA

El instrumento está garantizado contra cualquier defecto en el material o la fabricación durante el
período especificado en la tarjeta de garantía que se adjunta. Este período entra en vigor a partir de
la fecha de compra. Durante este período, se reemplazarán sin cargo alguno todas las piezas
defectuosas, a condición que el defecto sea resultado de un accidente, uso incorrecto o negligencia.
El distribuidor del instrumento proporcionará información sobre las reparaciones realizadas bajo esta
garantía.

Este manual se ha preparado con una finalidad informativa para los clientes de Techne y ninguna
parte del manual se deberá considerar como una garantía, condición o reflejo con respecto a la
descripción, comerciabilidad, idoneidad para un fin determinado o de otro tipo de la unidad o sus
componentes.

Con independencia de la descripción y las especificaciones del instrumento que se indican en el
manual del operario, Techne se reserva el derecho de realizar cambios en el instrumento o en
cualquiera de sus componentes cuando lo estime oportuno.

16

CONTACT INFORMATION

UK

North and South America

France

Asia

Middle East

For technical, sales or servicing information, contact your local Techne dealer or:

Bibby Scientific Ltd.
Beacon Road
Stone
Staffordshire
ST15 0SA
UK
Tel: [phone]
Fax: [phone]
E-mail: [e-mail]

www.techne.com

Bibby Scientific Limited
Bâtiment Le Deltaparc Parc Silic PN2
7 rue du Canal
BP 55437 VILLEPINTE
95944 ROISSY Charles de Gaulle
France
Tel: [phone]
Fax: [phone]
E-mail: [e-mail]

www.bibby-scientific.com

Bibby Scientific Middle East Ltd.
PO Box 27887, Engomi 2433
Nicosia
Cyprus
Tel: [phone]
Fax: [phone]
e-mail: [e-mail]

Bibby Scientific US Inc. t/a Techne Inc.
3 Terri Lane, Suite 10
Burlington, N.J. 08016
USA
Toll Free (in NA): 800-225-9243
Tel: [phone]
Fax: [phone]
E-mail: [e-mail]

www.techneusa.com

Bibby Scientific - Singapore
Prudential Tower, Level 26
30 Cecil Street
Singapore 049712
Tel: [phone]
Fax: [phone]
e-mail: [e-mail]

www.bibby-scientific.com

17

DB100/2, DB100/3 AND DB100/4

SPECIFICATIONS

Specification

Number of insert blocks 2 3 4
Temperature display 5 character LED 5 character LED 5 character LED

Working temperature range

Minimum set temperature 0°C 0°C 0°C
Set point resolution 0.1°C 0.1°C 0.1°C
Set point accuracy at 37°C ≤±1°C ≤±1°C ≤±1°C
Set point accuracy at 100°C ≤±1.5°C ≤±1.5°C ≤±1.5°C
Temperature stability at 37°C ≤±0.1°C ≤±0.1°C ≤±0.1°C
Temperature stability at 100°C ≤±0.15°C ≤±0.15°C ≤±0.15°C
Max. temperature variation

within a block
Max. temperature variation

between similar blocks
Heat up time 25°C to 100°C 8 minutes 7 minutes 7 minutes

Countdown Timer with audible
beeps

Minimum / Maximum timer 1min / 99h59min 1min / 99h59min 1min / 99h59min

DB100/2

DB100/2/115

Ambient +5°C to

100°C

<0.2°C at 37°C

<0.3°C at 100°C

<0.5°C at 37°C

<1.0°C at 100°C

Yes Yes Yes

DB100/3

DB100/3/115

Ambient +5°C to

100°C

<0.2°C at 37°C

<0.3°C at 100°C

<0.5°C at 37°C

<1.0°C at 100°C

DB100/4

DB100/4/115

Ambient +5°C to

100°C

<0.2°C at 37°C

<0.3°C at 100°C

<0.5°C at 37°C

<1.0°C at 100°C

Safety over-temp cut-out Thermal fuse Thermal fuse Thermal fuse
Overall dimensions (W x D x H) 202 x 260 x 105mm 279 x 260 x 105mm 356 x 260 x 105mm

Electrical supply

Power 300W 450W 600W
Shipping weight 5kg 6kg 7kg

Note: The control specifications are quoted for an ambient temperature of 20°C for units fitted with
2, 3 or 4 insert blocks type F3506. The specification will be closely held if the ambient temperature is
in the range 10°C to 30°C. Outside this range the quoted figures may deteriorate but the unit will still
work safely.

Note: Different block inserts may take different amounts of time to equilibrate to the same
temperature.

18

230V or 115V,

50-60Hz

230V or 115V,

50-60Hz

230V or 115V,

50-60Hz

DB200/2 AND DB200/3

Specification

Number of insert blocks 2 3
Temperature display 5 character LED 5 character LED
Working temperature range Ambient +5°C to 200°C Ambient +5°C to 200°C
Minimum set temperature 0°C 0°C
Set point resolution 0.1°C 0.1°C
Set point accuracy at 37°C ≤±1°C ≤±1°C
Set point accuracy at 100°C ≤±1°C ≤±1°C
Temperature stability at 37°C ≤±0.1°C ≤±0.1°C

DB200/2

DB200/2/115

DB200/3

DB200/3/115

Temperature stability at 100°C ±0.15°C ±0.15°C

Max. temperature variation within a block

Max. temperature variation between
similar blocks

Heat up time 25°C to 100°C 8 minutes 7 minutes
Heat up time 25°C to 200°C 23 minutes 19 minutes
Countdown Timer with audible beeps Yes Yes
Minimum / Maximum timer 1min / 99h59min 1min / 99h59min
Safety over-temp cut-out Thermal fuse Thermal fuse
Overall dimensions (W x D x H) 202 x 260 x 105mm 279 x 260 x 105mm
Electrical supply 230V or 115V, 50-60Hz 230V or 115V, 50-60Hz
Power 300W 450W
Shipping weight 5kg 6kg

<0.2°C at 37°C

<0.2°C at 100°C

<0.5°C at 37°C

<1.5°C at 100°C

<0.2°C at 37°C

<0.2°C at 100°C

<0.5°C at 37°C

<1.5°C at 100°C

Note: The control specifications are quoted for an ambient temperature of 20°C for units fitted with
2, 3 or 4 insert blocks type F3506. The specification will be closely held if the ambient temperature is
in the range 10°C to 30°C. Outside this range the quoted figures may deteriorate but the unit will still
work safely.

Note: Different block inserts may take different amounts of time to equilibrate to the same
temperature.

19

DB100/2TC

Specification

Number of insert blocks 2
Temperature display 5 character LED

DB100/2TC

DB100/2TC/115

Working temperature range
“Temperature setting range”

Minimum set temperature 0°C
Set point resolution 0.1°C
Set point accuracy at 37°C ≤±1°C
Set point accuracy at 100°C ≤±1.5°C
Temperature stability at 37°C ≤±0.1°C
Temperature stability at 100°C ≤±0.15°C

Max. temperature variation within a block

Max. temperature variation between similar
blocks when set to the same temperature

Heat up time 25°C to 100°C 8 minutes
Overall dimensions (W x D x H) 279 x 260 x 105mm
Countdown Timer with audible beeps Yes
Minimum / Maximum timer 1min / 99h59min
Safety over-temp cut-out Thermal fuse
Overall dimensions (W x D x H) 279 x 260 x 105mm

Ambient +5°C to 100°C

<0.2°C at 37°C

<0.3°C at 100°C

<0.5°C at 37°C

<1.0°C at 100°C

Electrical supply

Power 300W
Shipping weight 5kg

230V or 115V,

50-60Hz

Note: The control specifications are quoted for an ambient temperature of 20°C for units fitted with
2, 3 or 4 insert blocks type F3506. The specification will be closely held if the ambient temperature is
in the range 10°C to 30°C. Outside this range the quoted figures may deteriorate but the unit will still
work safely.

Note: Different block inserts may take different amounts of time to equilibrate to the same
temperature.

20

OPERATION

INSTALLATION

See also the sections on Safety and Installation.

1. Place the unit on a suitable flat bench or in a fume cupboard if required, ensuring that the air inlet
vents on the underside are free from obstruction.

2. Select the insert aluminium alloy block(s) appropriate for the application. A list of available blocks
is given in the section ‘Accessories’. Ensure that both the underside of the block(s) and the top of
the hotplate are clean; efficient heat conduction between these two surfaces is essential.

Top view showing three insert blocks in place

3. Place the insert blocks onto the hotplate in the well of the unit and place the tubes containing the
sample liquid in the blocks.

4. The heater design, temperature sensor and control circuit give good temperature control and
uniformity, but it is important that there is a close fit of the tubes in the block to allow efficient heat
transfer.

5. If less than the maximum number of insert blocks are fitted it is recommended that plastic half
blocks (part code F4466) are fitted to the space either side of the aluminium block. The half blocks
have the effect of reducing heat loss, thus improving temperature stability.

Rear view

1. Power ON/OFF switch.

2. Mains cable socket.

6. Plug the mains cable into the socket in the rear of the unit. Connect to the mains electricity supply
with the plug provided or one wired correctly for your supply. Switch the power ON from the switch
located next to the mains input lead. The front display will then light up.

21

POWER UP SCREEN

When you first switch on, the display will initially flash the currently installed firmware version of the
unit. It will display this for 1 second and then the actual temperature of the plate will be indicated.

THE FRONT PANEL CONTROLS

The front panel controls consist of four buttons for controlling the display, a five digit LED display and
three indicators.

The front panel controls

1. Five digit LED display.

2. Power indicator. When lit, this shows that there is power to the unit.

3. Heater indicator. When this is flashing, it indicates that the heater is heating the unit or
controlling the temperature. If the Dri-Block® is above the set temperature then the indicator
will be off.

4. Over-temperature indicator. If this is lit, it indicates that the unit has developed a fault and the
over-temperature cut-out has been triggered. This will cause the heater to be switched off and
the unit will begin to cool even if the heater light is on. The unit should be returned to Bibby
Scientific or its authorised agent for investigation.

5. Set/reset. Press to show the set temperature. If the timer is activated, pressing and holding
this button deactivates the timer. This button also silences the beeper.

6. Up arrow button. Used together with the set/reset button or timer button to increase the set
temperature or time. Used together with the Down arrow button, this button can be used to
change the temperature display from °C to °F.

7. Down arrow button. Used together with the set/reset button or timer button to decrease the set
temperature or time.

8. Timer. Press to set or activate the timer. This button also silences the beeper.

22

SETTING THE TEMPERATURE UNITS

1. Press the Up arrow and Down arrow buttons together to toggle between °F and °C.

Note: When the unit is tuned off, on subsequent power-up the units will revert to °C.

SETTING THE OPERATING TEMPERATURE

1. To display the set temperature on the digital display, press and hold the set/reset button.

2. To adjust the set temperature, press the set/reset button and hold it while pressing the Up or
Down arrow buttons. Each press of the Up arrow or Down arrow buttons will increase or
decrease the set temperature by 0.1°C. If the buttons are held down the temperature change
will accelerate to 20°C per second.

3. When the set/reset button is released, the current heater temperature is displayed.

4. The heater indicator will flash if the new set temperature is higher than the current heater
temperature and will continue to flash to show that the unit is controlling the temperature.

5. The heater indicator will turn off if the new set temperature is lower than the current heater
temperature and will only start to flash when approaching the set temperature.

6. For optimal accuracy, allow the block inserts to equilibrate to the set temperature for about 30
minutes.

DB100/2TC

The model D100/2TC accommodates 2 aluminium blocks with independent temperature controls so
that each block may be set to a different temperature. The operation of the controls for each block is
as described above.

If using this model with only one block in place, the side with no block should have its set temperature
adjusted to 30°C.

Note: Due to variations in heat losses with different designs of insert block, the actual temperature
may vary. The units are calibrated using model F3506 insert blocks. If you need to control the
temperature to a greater accuracy than the instrument’s set point, place a thermometer in a
designated hole in one of the blocks. For greater accuracy still, you can place a thermometer in the
sample liquid in one of the test tubes.

In either of these cases, it may be necessary to readjust the set temperature to achieve the precise
temperature required. Allow the temperature of the unit to stabilise after each adjustment. There will
be a time lag between the heater plate and the insert block achieving the set temperature due to the
thermal contact between them.

SETTING THE TIMER

1. To set the timer, press and hold the timer button and press the Up or Down arrow buttons.
Each press of the Up arrow or Down arrow buttons will increase or decrease the set time by 1
minute. If the buttons are held down, the time change will accelerate to 200 min per second.

2. Release the timer button to activate the timer. An audible beep will be heard once the timer is
activated.

3. When the count-down time has completed, an audible beep will be heard and the display will
show the word ‘End’ alternatively with the current heater temperature. Press the set/reset
button to cancel the beeper. The unit will start to cool to ambient once the count-down time
has completed.

4. To stop the timer at any point during the count-down period, press and hold the set/reset
button or the timer button until the word ‘Stop’ appears and an audible beep is heard.

23

5. To display the current heater temperature while the timer is active, press the timer button. The
display will show the heater temperature and the letter ‘t’ will flash on the left hand side
indicating the timer is counting down. Press the timer button again to revert to the timer count­down.

6. To re-run the same timer count-down, press the timer button until an audible beep is heard.

7. To turn the timer function off, press and hold the timer button and press the Down arrow
button until the word ‘OFF’ appears.

AFTER USE

When you have finished heating samples, remember that parts of the unit – the tubes, blocks and
associated accessories – may be very hot. Take the precautions listed in the section Safety and
Installation. We recommend that the blocks should be allowed to cool to 70°C or below before being
removed from the heating unit.

To remove an insert block, screw the extractor tool into the threaded hole and lift the block out
vertically. Never leave the extractor tool in the block while it is being used in the Dri-Block® heater.

Removing an insert block with the extractor tool

USER MAINTENANCE

Before cleaning your unit, disconnect it from the power supply. The outer case of the Dri-Block®
heater may be cleaned with a cloth dipped in water or ethanol (methanol can also be used). No part
of the case or cover should be immersed in the solvents. Do not use aggressive solvents such as
acetone or abrasive cleaners. Do not use bleach or strong acids.

Before using any cleaning or decontamination method except those recommended here, the
responsible person should check with Techne that the proposed method will not damage the
equipment.

24

CALIBRATION

Note that if you change the calibration from that set at the factory you may change the
calibration at all temperatures. You may get different calibration with different blocks.

Make sure that you have good thermal contact between the insert blocks and the heater plate in the
Dri- Block® heater. For best results, push all the block inserts to the right hand side so they are
touching. In order to ensure that the calibration you are setting is correct, you will need to use an
independently calibrated temperature probe or thermometer.

First, measure the actual temperature of the particular block you want to use in the Dri-Block® heater
using the calibrated probe or thermometer. If the calibration is not correct then you can follow the
procedure outlined below. Before you begin, make sure that the block and the unit are below 35°C.

1. Set the temperature display to the lowest setting. This will ensure that the block is at ambient
temperature for the next procedure.

2. Insert your calibrated probe or thermometer into the thermometer hole of the right hand block
insert. A little silicone oil can be placed in the hole if necessary to give a better heat transfer.

3. Press and hold the Down arrow button then press the Up arrow button. The word ‘CAL’ will be
shown on the display. The unit will now heat to 40°C and stabilise for 30 minutes.

4. After a period of 30 minutes the unit will beep and the display will change to show the word
‘rEAdy’. Measure the actual temperature of the block using the thermometer or probe.

5. Press the set/reset button and using either the Up arrow or the Down arrow buttons, adjust the
display to show the same temperature as the value measured by the thermometer.

6. Press and hold the set/reset button then the timer button. The unit will beep and proceed to
the next calibration temperature. With the DB100 units the second calibration temperature is
95°C and with the DB200 units the temperature is 195°C. The unit will now heat and stabilise
for 30 minutes.

7. After a period of 30 minutes the unit will beep and the display will change to show the word
‘rEAdy’. Measure the actual temperature of the block using the thermometer or probe.

8. Press the set/reset button and using either the Up arrow or the Down arrow buttons, adjust the
display to show the same temperature as the value measured by the thermometer.

Note: Up to this point it is possible to cancel the calibration by turning the unit off.

9. To complete the calibration procedure, press and hold the set/reset button then the timer
button. The unit will beep and the word ‘done’ will briefly flash on the display. The unit will
return to normal operation.

Note: The calibration routine for the DB100/2TC is the same as above except each block position
should be calibrated separately.

Note: Aluminium block inserts are designed to allow for thermal expansion up to 200°C. For this
reason there will be a small air space around the blocks at ambient temperature. The heat source is
the base of the Dri- Block® heater. For best results push all the block inserts to the right hand side so
they are touching.

25

ADDITIONAL INFORMATION

Note that this equipment should only be dismantled by properly trained personnel. Removing the
outer cover exposes potentially lethal mains voltages. There are no user serviceable parts within this
equipment.

FAULT FINDING

Should you have any problems with your Dri-Block® heater which cannot be easily remedied, you
should contact your supplier and return the unit if necessary. Please include details of the fault
observed and remember to return the unit in its original packing. Bibby Scientific Ltd. accepts no
responsibility for damage to units which are not properly packed for shipping: if in doubt, contact your
supplier, giving the full serial number of the unit.

FUSES

If the display on the front panel is not lit, one of the two fuses may have blown. Check that there is no
external cause, such as a faulty plug or lead. Check both fuses and replace the faulty fuse with a
new one of the correct value (fuse values are given on the label next to the power inlet). Note that
fuses should only be replaced by a qualified electrician.

The holder for the two fuses is built into the mains input socket. First remove the power cable and
then gently prise the fuse drawer open with a flat-bladed screwdriver or similar tool. Each fuse can be
removed by using the screwdriver as a lever.

Exchange the faulty fuse in the fuse holder for a working fuse of the correct value. Finally, replace
the fuse drawer in the fuse compartment and push the drawer shut. Fuses which blow repeatedly
indicate a serious fault and you should return the unit to your supplier for repair.

Model Fuses for 230V Fuses for 115V

DB100/2 2 x 3.15 Amp 2 x 4.00 Amp
DB100/3 2 x 3.15 Amp 2 x 6.30 Amp
DB100/4 2 x 4.00 Amp 2 x 6.30 Amp
DB200/2 2 x 3.15 Amp 2 x 4.00 Amp
DB200/3 2 x 3.15 Amp 2 x 6.30 Amp
DB100/2TC 2 x 3.15 Amp 2 x 4.00 Amp

SAFETY OVER-TEMPERATURE CUT-OUT

In the event of a fault occurring which could cause the heater to over-heat, a thermal fuse will cut in
and remove power from the heater. This will occur when the temperature reaches approximately
192°C in the DB100 models and 240°C in the DB200 models.

26

SUPPORT CONTACTS

If you require further technical or application assistance please contact Techne at:
E-mail: [e-mail].
Phone: [phone]
Fax: [phone]

For servicing information please contact:
Bibby Scientific Ltd.

Service Department
Beacon Road
Stone
Staffordshire
ST15 0SA
E-mail: [e-mail].

Phone: [phone]
Fax: [phone]

We are continually striving to improve our products and software. If you have any comments and
suggestions on how we can do things better please send them to us at: technehelp@bibby-

scientific.com.

27

ACCESSORIES

Insert blocks are made of aluminium alloy and must be ordered separately from the heater units. The
following block inserts can be obtained from Bibby Scientific Ltd. or your Techne distributor:

Part

code

F3501 Plain block (single) None - - - 95 x 75 x 50
F3502 6mm 30 6.5 38 Conical 95 x 75 x 50
F3503 10mm 20 10.5 48 Conical 95 x 75 x 50
F3504 12mm 20 12.75 48 Conical 95 x 75 x 50
F3505 13mm 20 13.8 48 Conical 95 x 75 x 50
F3506 15mm 12 15.75 48 Conical 95 x 75 x 50

F3507

F3508 19mm 8 19.75 48 Conical 95 x 75 x 50
F3509 25mm 6 25.75 48 Conical 95 x 75 x 50
F3510 10mm Cuvettes 2 channels 13 x 95 38 Flat 95 x 75 x 50

F3512 Plain block (triple)

F4460 Plain block (single)

F4461 7mm and 9mm 20 + 10 7.0 and 9.5 38 Conical 95 x 75 x 50
F4462 24mm 6 24.75 48 Conical 95 x 75 x 50
F4463 26mm 6 26.75 48 Conical 95 x 75 x 50

F4464

F4464R

F4464B

F4465

F4466

F4470

F4471

F4473 96-Well PCR plate 96 5.5 17.3 Tapered 95 x 150 x 61

F4476

F4477 384-Well PCR plate 384 3.57 7 Tapered 95 x 150 x 61
F4480 50ml Falcon tubes 5 28.9 48 Conical 95 x 75 x 50

F4481

F4485 30mm tubes 5 30.5 48 Conical 95 x 75 x 50
F4487 43mm vessels 2 43.8 45 Flat 95 x 75 x 50
F4490 20mm tubes 8 20.75 48 Conical 95 x 75 x 50
F4501 12mm Vials 20 12.75 25 Conical 95 x 75 x 50
F4515 20mm Vials (triple) 18 20.2 35 Flat 95 x 225 x 50
F4516 23mm Vials (triple) 18 23.2 35 Flat 95 x 225 x 50
F4567 12mm Vials 20 12 24 Flat 95 x 75 x 50
F4568 15mm Vials 12 15.75 30 Flat 95 x 75 x 50
F4569 12mm Vials 20 12.75 20 Flat 95 x 75 x 50
F4675 16mm Vials 12 16.75 35 Flat 95 x 75 x 50
F4676 13mm Vials 20 13.8 25 Flat 95 x 75 x 50

Nominal tube size

16mm and 15ml

Falcon tubes

1.5ml Microfuge
tubes

1.5ml Microfuge

tubes (red)

1.5ml Microfuge

tubes (blue)

0.5ml Microfuge
tubes

Half block plastic

spacers

2.0ml Microfuge
tubes

0.2ml Microfuge
tubes

Gelation timer

sample cup

96-Well flat-bottom

plate

Number of

holes

12 16.75 48 Conical 95 x 75 x 50

Thermometer

only

Thermometer

only

20 10.9 35 Tapered 95 x 75 x 50

20 10.9 35 Tapered 95 x 75 x 50

20 10.9 35 Tapered 95 x 75 x 50

30 7.9 27 Tapered 95 x 75 x 50

- - - -

20 10.8 35 Conical 95 x 75 x 50

72 4.4 13.8 Tapered 95 x 75 x 50

1 46.5 48 Flat 95 x 75 x 50

Rectangular

ridge

Hole

diameter

(mm)

- - - 95 x 225 x 50

- - - 95 x 75 x 50

28.9 48 Flat 95 x 150 x 61

Hole

depth

(mm)

Base

profile

Block

dimensions

(mm)

98.8 x 40.2 x

18.5

28

REPLACEMENT PARTS

The following replacement parts can be obtained from Bibby Scientific Ltd. or your Techne dealer:

Product code Description

HH179(S) UK mains lead with plug, 230V
HH180(S) European mains lead with plug, 230V
FCABLEUS US mains lead with plug, 115V
6101308 Spare block extraction tool

29

DECLARATION OF CONFORMITY

30