*Utilizes standard 9V alkaline battery (not included), which will provide a life
POWER REQUIREMENTS
span of approx. 70 hours. NOTE: Input jack activates battery.To conserve
energy, unplug when not in use. Power Consumption: approx. 7mA.
*USE DC POWER SUPPLY ONLY! Failure to do so may damage the
unit and void warranty. DC Power Supply Specifications:
-9V DC regulated or unregulated, 100mA minimum;
-2.1mm female plug, center negative (-).
Optional factory power supply is available: Tech 21 Model #DC2.
WARNINGS:
* Attempting to repair unit is not recommended and may void warranty.
* Missing or altered serial numbers automatically void warranty. For your own
protection: be sure serial number labels on the unit’s back plate and exterior
box are intact, and return your warranty registration card.
ONE YEAR LIMITED WARRANTY. PROOF OF PURCHASE
REQUIRED. Manufacturer warrants unit to be free from defects in materials
and workmanship for one (1) year from date of purchase to the original purchaser and is not transferable. This warranty does not include damage resulting
from accident, misuse, abuse, alteration, or incorrect current or voltage. If unit
becomes defective within warranty period, manufacturer will repair or replace
it free of charge. After expiration, manufacturer will repair defective unit for a fee.
ALL REPAIRS for residents of U.S. and Canada: Call Tech 21 for Return
Authorization Number. Manufacturer will not accept packages without
prior authorization, pre-paid freight (UPS preferred) and proper insurance.
FOR PERSONAL ASSISTANCE & SERVICE:
Contact Tech 21 on normal business weekdays from 9:00 AM to 5:00 PM, EST.
MADE IN THE U.S.A.
SansAmp Character Series - VT Bass Deluxe
T: 973-777-6996 • F: 973-777-9899
E: info@tech21nyc.com • www.tech21nyc.com
©2010 Tech 21 USA, Inc.
OWNER’S MANUAL
TECH 21, THE COMPANY
Tech 21 was formed by a guitarist possessing the unusual combination of a trained ear and electronics expertise. In 1989, B. Andrew Barta incorporated Tech 21 and made his invention commercially available to players and studios around the world. His highly-acclaimed SansAmp™ pioneered Tube Amplifier Emulation in professional applications for recording direct and performing
live, and created an entirely new category of signal processing. There have since been many entries
into this niche, yet SansAmp continues to maintain its reputation as the industry standard.
In addition to a full line of SansAmp models, Tech 21 also offers effect pedals; battery operable
MIDI footcontrollers, the MIDI Mouse and MIDI Moose; as well as “traditional” style amplifiers for
guitar and bass. Each product is thoughtfully and respectfully designed by B. Andrew Barta himself
with the player in mind.
Tech 21’s goal is to provide you with flexible, versatile tools to cultivate, control, refine and redefine your own individual sound. We take great pride in delivering consistent quality sound, studio to
studio, club to club, arena to arena.
PRODUCT OVERVIEW
SansAmp VT Bass Deluxe combines the warmth of a 100% analog signal path with the convenience
of digital programmability in a super simple, player-friendly stomp box format. Our proprietary technology captures the rich, natural harmonics and sweet overdrive characteristics inherent to tube
amplifiers, and does so even at low volume. SansAmp delivers the same dynamics, responsiveness, and
sound quality of massive pro stage rigs in a portable, programmable pedal.
You can explore and custom tailor bass tube amp tones from early '60s to classic super valve. The
ease of operation allows you to make changes on the fly, at the gig, even during your performance
--without having to take this manual with you. There are no complex formulas or numerical calculations to learn, so there’s nothing to get in the way of your creative flow.
Independent footswitches put your favorite tones right at your feet, from warm vintage to Sumosized overdrive. Custom actuators provide a smooth transition between channels for instantaneous switching, so you can dance to the music instead of your gear.
APPLICATIONS
WITH BASS AMP:
power amp input, a.k.a. “effects return” (if applicable), of an amp. This will bypass the tone coloring
section of the pre-amp and will defeat the amp’s master volume.
NOTE: BE SURE the BASS GUITAR VOLUME is OFF --BEFORE you turn on
the amp. Then slowly increase the volume of the bass. If it’s too loud overall, check that the 1/4”
Out Boost switch is disengaged (up) and then edit your presets accordingly. If it doesn’t get loud
enough for you, engage (depress) the 1/4” Out Boost switch to add 10dB.
Or, you can run the SansAmp into the front input of an amp. Be sure to keep the Level of
SansAmp close to unity gain, so as not to overload the amp’s input, which could result in undesirable distortion.
Tips for setting up your amp when using front input:
1. Plug into low gain channel or input.
2. Turn off Bright switch.
3. Turn presence control (if applicable) to 12 o’clock or below.
4. Set tone controls as flat as possible.
Run the 1/4” output of the SansAmp directly into the input of the
TO DRIVE A POWER AMP: Run the output of the SansAmp into the input of a power
amp with an input sensitivity of -10dB to 0dB. Then use the master volume control of the power
amp to adjust your stage volume.
TO RECORD DIRECT: You can plug directly into the input of a mixer/recorder and use
the on-board sounds of the SansAmp. Bear in mind, full-range systems yield a wide frequency
response. Therefore, you may need to adjust the EQ settings of the SansAmp to compensate.
THE INS AND OUTS
Standard Audio Procedure: TURN (
avoid unwanted and potentially speaker-damaging “pops” when connecting or disconnecting any
equipment, always mute mixing board and/or turn down amp volume before plugging or
unplugging!
SansAmp)
ON FIRST. TURN OFF LAST. To
WARNING:
DO NOT run the speaker output of any amp directly into the
SansAmp. Severe damage to the amp and/or SansAmp may result.
SIGNAL LEVEL TO INPUT
SansAmp VT Bass is designed to accommodate instrument level signals to the Input, such as the
output of a bass, the output of distortion pedals, etc. Signal level to Input should be close to that
of a standard electric guitar (approx. -10dB / 250mV). NOTE: Hot pickups will increase the gain
structure of the SansAmp VT Bass.
IN A (MAIN): 1/4-inch 1 megOhm, instrument level. Use as your main input when using a
single instrument. Also switches battery power on/off. To avoid battery drain, unplug when unit is
not in use.
IN B: 1/4-inch 1 megOhm, instrument level. For second instrument.
PARALLEL OUTPUT: 1/4-inch buffered, unbalanced direct output. Instrument signal pass-
es through, Uneffected, to the input of your stage amplification system or tuner.
BALANCED XLR OUTPUT: Balanced 600-Ohm low Z output. Sends effected or
bypassed signal to mixing console/recorder.
XLR Out Pad Switch: -20dB pad to match the output to equipment
with different input level requirements. In the line level (up) position, the
output is 0dB. In the instrument level (down) position, the output is -20dB.
1/4” OUTPUT: Unbalanced 1KOhm low Z output. Sends effected or
bypassed signal to amp rig or power amp.
1/4” Out Boost Switch: +10dB boost to match the output to equipment with different
input level requirements. In the instrument level (up) position, the nominal output is -10dB. In
the line level (down) position, the output is 0dB.
PHANTOM POWER
Allows you to “tap into” the power of a suitably equipped mixer. As the 3-conductor XLR sends
the audio signal to the input of a mixer, the mixer sends voltage back to the unit via the same 3
wires, eliminating the need for an external power supply. Consult your mixer’s owner’s manual for
set-up instructions. For live and studio use, let the engineer know your SansAmp is phantom
power operable.
NOTE: Minimum 24V DC regulated phantom power supply, however, 48V DC regulated is recom-
mended to optimize headroom and illuminate LEDs.
PHANTOM & GROUND CONNECT SWITCH: When engaged (depressed), the
ground connects and unit will accept phantom power through the XLR Output. Disengaged (up),
the ground of your stage system and other interconnected gear is lifted/isolated from the ground
of the mixing console.
With a mixer only: If you are plugging your bass into the VT Bass and taking the XLR Output
to a mixer --and do not have any other grounded equipment connected in the
setup-- you will have to engage (depress) the switch to connect the ground and activate the
phantom power.
2
With a mixer and bass amp: If you are going to the mixer via the XLR and using the 1/4”
Output to feed a bass amp (with its own AC ground), you should set the switch in the up position
for “Ground Lift” mode. If you experience hum and/or buzz with the switch in either position,
there is probably a problem with the AC outlets you are plugging into.
NOTE: If using vintage equipment without proper grounds, take extra care connecting it
to modern grounded equipment. The inadequacies of the ground in vintage gear could result in
damaging anything it is connected to.
NOTE: While operating under phantom power, we recommend keeping a 9V alkaline
battery installed at all times to avoid the previously mentioned “pops” when lifting the ground (see
Standard Audio Procedure on page 2).
GUIDE TO CONTROLS
CHARACTER
amplifier. In addition to modifying the frequency response, Character also influences the attack and drive
characteristics. Therefore, you may need to adjust your gain and tone settings after tweaking the
Character control.
sweeps through an entire range of tonal possibilities associated with this style of
• Settings below 12 o’clock will give you the ‘70s powerhouse, the SVT.
• Around 12 o’clock will introduce you to the studio staple, the flip top.
• Above 12 o’clock increases the gain and crunch for less polite, modern
rock, indie bass sounds.
• Full up yields distorted bass tones from Yes to Crimson to King’s X styles.
DRIVE adjusts the overall amount of gain and overdrive, similar to when the output section of a
tube amp is being pushed.
LOW, MID, HIGH. Unlike passive controls that only cut, these active tone controls cut or
boost ±12dB from unity gain (12 o’clock). MID is custom tuned to 12dB @ 500 Hz.
LEVEL adjusts the output level of both the 1/4” and XLR outputs.
PROGRAMMING THE CHANNELS
HOW TO SAVE A PROGRAM
Select a channel where you want the setting located. Set the knob controls to taste. Double click
on that channel’s footswitch and it’s saved. It’s that easy.
HOW TO FIND KNOB POSITIONING WITHIN A PRESET
When you turn a knob from its stored position, it “unlocks” and the channel indicator LED will
blink. The slower the blink, the farther away you are from the preset point. The faster the blink,
the closer you are. At the preset point, the LED stops blinking and remains on.
LAZY POT™
Another Tech 21 first, this is a unique safety feature engineered for the Drive and Level controls.
When you “unlock” the EQ settings, for instance, they will “jump” to the new setting of the knob
position. For the Drive and Level controls, however, this could result in you jumping out of your skin if
they’re at a high setting. With the Lazy Pot, there’s a gradual increase to the new setting position, giving you time to turn it down. This will only happen when you initially unlock a preset. Once unlocked,
the pot will react according to how you reposition it.
BYPASS
SansAmp VT Bass can go into bypass mode from any of the three channels. Whichever channel
you’re already in, hit that channel’s footswitch once and you’ll be in bypass mode.
BANK A and B
You can program 3 presets per bank for a total of 6 presets. You can utilize 3 per instrument or all
6 for one bass. Just follow the same save procedure for each channel in each bank.. When you
alternate between banks via the footswitch, the corresponding LED lights up to let you know
which bank you’re in.
Allows you to connect and control external effects. Run the input of your effect to FX SEND;
EFFECT LOOP
output of your effect to FX RETURN. We recommend time-based effects (i.e., chorus or delay) be
inserted in the Effect Loop and external distortion/wah pedals be placed between the bass and
the SansAmp.
To engage/disengage the effect loop, double-click the Bank/FX footswitch.
NOTE: The effect loop automatically stores the position of the last state it is in. For example, if
the effect loop is on when you save a program, it will engage when you recall that preset. If you
should spontaneously disengage the effect loop during a performance, the next time you recall
that preset, the effect loop will be off.
SPEAKER SIMULATION
Built-in speaker simulation is tuned to match 10-inch American-style bass speakers and is an integral part of the SansAmp circuitry. It is specifically designed for a smooth, even response as would
be achieved by a multiply-miked cabinet, without the peaks, valleys, and notches associated with
single miking. Therefore, it will not adversely affect or interfere with the sound of your own
speaker cabinet.
PLACEMENT ORDER OF OTHER EFFECTS
One of the key attributes of any SansAmp is its responsiveness to the dynamics and nuances of
your playing technique. In most cases, your bass should be plugged directly into the SansAmp. We
suggest experimenting to find the order that’s best for you. As a general guide, we recommend:
Place the following effects BEFORE the SansAmp VT Bass:
Wah-Wah, Pre-Amp, Compressor, Fuzz Box, Envelope Follower.
Place the following in the FX loop or AFTER SansAmp VT Bass: Chorus, Delay,
EQ, Pitch Shifter, Reverb.
NOTE: Low quality digital effects placed after the SansAmp may compromise your signal and
degrade the sound.
NOTEWORTHY NOTES
1) Do not A/B (compare) the SansAmp IN LINE with a digital product. When
linked in series with a digital pre-amp/processor, the A/D to D/A conversion will impact the unit’s
sound. For an accurate comparison, run them parallel (separately) and manually plug in and out of
each.
2) SansAmp is very responsive. Our controls are unusually sensitive and powerful. You
need not set everything at max to get maximum results. For instance, to brighten your sound,
rather than automatically boosting Treble all the way up, try cutting back on the Bass first.
The tone controls also help compensate for the EQ curves found in bass amps. To find the best
settings for interacting with your amp, start with the tone controls at 12 o’clock and cut or boost
as necessary. Be aware that amplifiers vary greatly and some may require you to use radical EQ
settings on the SansAmp to achieve your desired sound. You need not be discouraged or suspect
something is wrong with the unit. If you’ve got your sound, you’ve simply found the right balance
for your particular amp.
3) The noise level of SansAmp is exceptionally low. However, it may amplify noise
emanating from the input source. To minimize noise going into the SansAmp VT Bass, we recommend active electronic instruments have the volume set at unity gain/maximum and tone controls
positioned flat. If you need to boost, do so slowly and sparingly.
Also check for pickup interference by moving your guitar or turning the volume off. Be aware single coil pickups are more likely to generate noise.
3
4) Preset and Sample Setting levels and tones will vary depending on the bass, amp
SAMPLE SETTINGS SAMPLE SETTINGS
F
AT TUBE
FLIP-TOP-style
RAGE
SVT
®
-style
T
FUZZED OUT
and cabinet you use. They were determined using a “typical” bass and cabinet, and are provided as
a starting point. So, some adjustments may be necessary, particularly to the Level control. For
instance, if you have a high output bass, a clean setting will be louder than a distorted one.
Conversely, a low output bass will require a higher level for a clean setting. If you have a big cabinet, the Fat Tube setting will be louder. With a smaller cabinet, the Flip Top setting will be louder.
5) Buffered bypass eliminates the shortcomings associated with “true bypass” (pops and clicks,
and high-end loss when multiple pedals are connected together), as well as signal loss associated
with other types of switching circuits.
6) Custom actuators. All Tech 21 pedals feature smooth, silent-switching actuators that are
licensed by other major manufacturers.
7) REMEMBER THIS WARNING: DO NOT run the speaker output of any amp
directly into the SansAmp. Severe damage to the amp and/or SansAmp may
result.
GLOBAL RESET
To reset your unit back to factory specifications, you can perform the following procedure: Hold
down the footswitches for Channels 1 and 3 while simultaneously applying power (either plugging in
an adapter or, if a battery is installed, plugging in your guitar cable). Then release the switches.
Or, you can reprogram each of the first six Sample Settings:
[Bank A] (1) Fat Tube (2) Flip Top-style (3) Rage
[Bank B] (4) SVT®-style (5) Thumpy Funk (6) Fuzzed Out
4
WARM COMPRESSION
YES-style
®
R
egistered trademarks. Names of sample settings are intended for descriptive purposes only.
Name/Description ______________________________
Name/Description ______________________________
Name/Description ______________________________
Name/Description ______________________________
SAMPLE SETTINGS
5
Name/Description ______________________________
Name/Description ______________________________
Name/Description ______________________________
Name/Description ______________________________
N
ame/Description
______________________________
N
ame/Description
______________________________
Name/Description ______________________________
Name/Description ______________________________
6
Loading...