Thank you for purchasing this Team Associated product. This assembly manual contains instructions and tips for building and
maintaining your new SC10B RS RTR. Please take a moment to read through this manual to help familiarize yourself with these
steps. We are continually changing and improving our designs; therefore, actual parts may appear slightly different than the
illustrations. New parts will be noted on supplimentary sheets located in the appropriate parts bags. Check each bag for these
sheets before you start your build.
:: RTR Features
Features of the SC10B RS RTR:
• Fully assembled 2wd short course buggy based on the multi-time National Champion SC10 truck
• Full roll cage with window nets and integral nerf bars
• Water-resistant Brushless Speed Control with reverse
• XP 2.4GHz radio system with metal gear steering servo
• Powerful Reedy 540 sized brushless motor
• Factory finished body with authentic short course graphics
• Cockpit underbody with driver figure
• KMC replica hex drive wheels and aggressive short course tires with new narrow fronts
• Blue anodized aluminum V2 coil-over shock absorbers
• Sealed gear differential with heavy-duty gears
• Molded composite chassis and battery strap that accommodates NiMH or LiPo battery packs
• Water-resistant enclosed receiver box
• Realistic front and rear bumpers designed to absorb impacts
:: Additional Items Needed::: Items Included:
Your new SC10B RTR comes factory assembled including radio
gear, motor, and ESC. However, there are some items you will
need to complete your new kit.
Items needed:
• AA-size batteries for transmitter (x6)
(#302, 303 recommended)
up your hardware with the correct drawing until
you find the exact size. Each part in the foldout
has a number assigned to it for ordering
replacement parts.
Customer Service
Tel: 949.544.7500
Fax: 949.544.7501
4
:: Steering System
!
9610
Servo saver
bolt
9610
Servo saver
washer
(upper)
!
Remove bolt and
washer, continue
assembly per
instructions.
9610
Servo saver
bolt
9610
Servo saver
washer
(upper)
* With supplied wrench, tighten
servo sacer bolt completely, until it
hits bottom. Do not overtighten.
:: Steering System (cont.)
9659
Servo saver
(upper)
black grease
#6588
9659
Servo saver
(lower)
9659
Servo saver
(lower)
9657
Heavy duty
servo saver
spring
9610
Servo saver
washer
(lower)
x2
Servo saver
9610
Servo saver
bolt
9610
Servo saver
washer
(upper)
* With supplied
wrench, tighten servo
sacer bolt completely.
Do not overtighten.
9659
(lower)
!
:: Steering System (cont.)
6272
Dust cover
foam
6276
Ballstud
.20 short
(silver)
Ballstud
.20 short
6272
Dust cover
foam
6276
(silver)
x2
x2
9659
Block
carrier
bushing
x2
9659
Steering
rack
9659
Bellcrank
2221
4-40 x 7/16
bhcs
x2
:: Steering System (cont.)
9566
Top plate
3856
Steering
rack bushing
x4
6925
4-40 x 1/2
x3
shcs
5
9640
Steering
bolt
!
Do not overtighten steering
bolts. Make sure there is free
movement in the steering rack.
(right)
:: Front Suspension
6272
Foam
dust
cover
9880
Steering
blocks
hex style
(left, right)
4449
4-40 x 3/16
aluminum
locknut
Ballstud
.30 long
(silver)
.030 washer
(nylon)
6277
4187
3/16 x 3/8
x2
Steering
9640
Steering
bolt
(left)
3977
bearing
(3/16”)
9659
brace
9882
C clip
bulkhead
!
9563
Front
9823
SC10
chassis
9881
Front axle
(hex style)
6915
4-40 x 5/8
fhcs
!
Install the C clip on
the groove shown
below.
Build left and
right sides!
x2
:: Front Suspension (cont.)
!
7368
3/16” axle
shim
3977
3/16 x 3/8
bearing
!
Align the C clip on
the front axles
with the D shape
inside the steering
blocks.
9883
Wheel hex
adapter
(thin)
universal
7369
1/16”
roll pin
Build left and
right sides!
6
:: Front Suspension (cont.)
7260
4-40
small
plain nut
7922
Caster
block 30˚
(left, right)
:: Front Suspension (cont.)
9622
Outer
hinge pin
6272
Foam
dust
cover
3983
Ballstud
.30 short
(black)
9645
2-56 x 1/8
bhcs
9622
Kingpin
Build left and
right sides!
9645
2-56 x 1/8
bhcs
Build left and
right sides!
9580
Spacer
91201
Front arm
(left, right)
:: Front Suspension (cont.)
9630
Ballstud
washer,
aluminum
(.030”)
6917
4-40 x 3/8
bhcs
x2
x2
6272
Foam dust
cover
x2
2-56 x 5/16
6277
Ballstud
.30 long
(silver)
9621
Inner
hinge pin
4334
bhcs
x2
4-40 x 3/4
x2
x2
6295
4-40 plain
nut
6927
shcs
x2
9564
Front
hinge pin
brace
x2
6292
4-40 x 3/8
fhcs
x2
91202
SC10B
front shock
tower
91212
SC10B front
body mount
91200
SC10B
front bumper
(upper)
:: Front Suspension (cont.)
x2
7
6924
4-40 x 3/8
shcs
x4
:: Front Suspension (cont.)
91200
SC10B
front bumper
(lower)
91220
4-40 x 1 5/8
shcs
91200
SC10B
skid plate
2221
4-40 x 7/16
x2
bhcs
6915
4-40 x 5/8
fhcs
x2
:: Front Suspension (cont.)
Build left and
right sides!
7230
Ball cup
(large)
!
7230
Ball cup
(large)
3.30”
(83.9mm)
7253
2.62
turnbuckle
Orient the notch to the lef t throughout
the vehicle. It indicates which end of the
turnbuckle has the left hand threads.
3.48”
(88.3mm)
7101
2.80
turnbuckle
7230
Ball cup
(large)
7230
Ball cup
(large)
8
:: Front Suspension (cont.)
:: Transmission
9831
3.6x0.7mm
o-ring
9830
Outdrive
x2
x2
cup
91205
SC10B
roll cage
bracket
black grease
#6588
black grease
#6588
x2
9828
Diff gear
cover
9831
4.7x1.42mm
o-ring
9765
4-40 x 7/16
fhcs
9888
0.5mm gear
diff shim
black grease
#6588
x4
Build left and
right sides!
9830
2x8mm
round end
pin
Build two!
:: Transmission (cont.)
9829
Sun gear
#6588
black grease
Align pin with
groove in
sun gear
#6588
black grease
!
9828
Diff gear
52T, 48P
9831
4.7x1.42mm
o-ring
9888
0.5mm gear
diff shim
black grease
#6588
9830
2x8mm
round end
pin
:: Transmission (cont.)
spacer
9601
Top
shaft
9829
Sun gear
black grease
#6588
!
9829
x4
Planet gear
shims
2.5x6mm
9829
Planet
gear
4675
fhcs
x4
9
x4
!
Use the 1.5mm allen
wrench to tighten the
2.5x6mm fhcs on the
diff gear cover
!
black grease
#6588
Align pin with
groove in
sun gear
:: Transmission (cont.)
Transmission case
Ball bearing
3/16 x 3/8
9829
Cross pin
9826
(left, right)
3977
x2
x2
x2
!
Align flat
spots
9831
Diff gear
seal
9360
Idler
gear
black grease
#6588
!
Ensure free outdrive
rotation before
installation!
9602
Top shaft
spacer
9601
Top
shaft
:: Transmission (cont.)
6925
4-40 x 1/2
shcs
9832
x2
Ball bearing
10 x 16mm
9630
.030 alum.
ballstud
washer
x3
9819
Motor
guard
6928
4-40 x 1
shcs
3977
Ball bearing
3/16 x 3/8
6919
x2
4-40 x 5/16
bhcs
x3
x2
9361
Idler gear
shaft
10
:: Transmission (cont.)
6913
4-40 x 1 1/4
shcs
:: Transmission (cont.)
9603
Slipper
pad
x2
x2
7485
V2 slipper
hub
thread lock
#1596
!
x2
9654
Spur gear
(87T, 48P)
thread lock
#1596
* Install locknut until even with end of
shaft. Then tighten 3 turns for kit
slipper setting. Recheck after initial run.
91203
SC10B rear
bumper brace
(left, right)
9600
Motor
plate
7486
V2 slipper
washer
x2
Compress
spring !
!
7486
V2 slipper
spring
6629
5-40
locknut
:: Transmission (cont.)
6915
4-40 x 5/8
fhcs
x4
91203
SC10B
engine bay
side panel
(left, right)
x2
91203
SC10B rear
bumper
6924
4-40 x 3/8
shcs
6932
4-40 x 5/16
shcs
x2
x2
x2
:: Rear Suspension
11
9818
Rear chassis
plate
Hinge pin
(rear, inner)
:: Rear Suspension (cont.)
7448
Rear A-arms
(left, right)
9621
x2
x2
7487
Anti squat
shim
(2 degrees)
9645
2-56 x 1/8
bhcs
7487
Rear arm
mount
(3.5 degrees)
x2
9269
5-40 x 1/2
fhcs
x2
:: Rear Suspension (cont.)
x2
6277
Ballstud
.30 long
(silver)
6272
Dust cover
foam
x2
.030 alum.
ballstud
9564
Rear chassis
brace
9630
washer
x2
9269
5-40 x 1/2
fhcs
9643
5-40 x 7/16
shcs
x2
x4
12
:: Rear Suspension (cont.)
6927
4-40 x 3/4
shcs
:: Rear Suspension (cont.)
x2
7260
4-40 small
plain nut
9824
Rear shock
tower
x2
9644
5-40 x 9/16
shcs
x2
9643
5-40 x 7/16
shcs
x2
:: Rear Suspension (cont.)
6924
4-40 x 3/8
shcs
6922
4-40 x 1/2
fhcs
x2
x2
91212
SC10B rear
body mount
6928
4-40 x 1
shcs
x2
:: Rear Hubs
13
6272
Dust cover
foam
3983
Ballstud
.30 short
(black)
LEFT SIDE
SHOWN
:: Rear Hubs (cont.)
9584
Rear hub
carrier
(left, right)
7260
4-40 small
plain nut
7368
3/16 axle
shim
3977
Ball bearing
3/16 x 3/8
7377
Bearing
spacer
x2
Build left and
!
right sides!
9670
Rear axle
7369
1/16
universal
roll pin
9883
Wheel hex
adapter
!
Build left and
right sides!
7462
Dogbone
4187
Spacer
x2
:: Rear Hubs (cont.)
Build left and
right sides!
5407
O-ring
7230
Ball cup
(large)
9645
2-56 x 1/8
bhcs
x2
Orient the notch to the lef t
throughout the vehicle.
It indicates which end of
the turnbuckle has the left
hand threads.
(90.9mm)
7101
2.80
turnbuckle
9622
Hinge pin
(rear, outer)
!
3.58”
7230
Ball cup
(large)
14
:: Shocks
6469
Shock
cap
o-ring
7484
Shock
internal
spacer
Front
Shock
:: Shocks (cont.)
V2 RTR
front shock
body 1.02”
stroke
(blue)
5407
o-ring
Lower shock
seal cap
6465
Shock
piston
#3
9884
Red
7484
6469
Shock
cap
o-ring
7484
Shock
internal
spacer
Rear
Shock
6299
E-clip
9885
V2 RTR
front shock
body 1.39”
stroke
(blue)
5407
Red
o-ring
7484
Lower shock
seal cap
Remove
spurs
Piston
Piston number here
Use #3 = front shocks
Use #1 = rear shocks
6465
Shock
piston
#1
6459
Shock
shaft
1.02”
stroke
Front
Shock
:: Shocks (cont.)
6466
Downstop
thin
1/32”
x5
Front
Shock
6299
E-clip
7217
Eyelet
7217
Pivot
ball
6299
E-clip
Rear
Shock
Downstop
Rear
Shock
6458
Shock
shaft
1.32”
stroke
6466
thin
1/32”
x2
6299
E-clip
7217
Eyelet
7217
Pivot
ball
:: Shocks (cont.)
Shock fluid
30wt #5422
:: Shocks (cont.)
Shock fluid
30wt #5422
6441
Shock
cap
(molded)
15
* Shock Bleeding Steps:
1. Pull shock shaft down.
2. Fill shock body 3/4 full with silicone fluid.
3. Slowly move the shock shaf t up and
down to remove air from under piston.
4. Wait for bubbles to come to surface.
5. Fill shock body to top with silicone fluid.
6. Place several drops of oil in the cap and
on cap threads.
7. Install cap and tighten completely.
8. Slowly compress shaf t all the way to
the top. If there is pressure at the top
of the stroke, there is too much oil or air.
You must bleed it out.
9. Slowly pull shaft down.
10. Unscrew the cap 3/4 turn and tilt the
shock at a slight angle.
11. Slowly compress the shaft to push out
excess oil and air. You should see
bubbles coming out from under the cap.
12. With the shaft compressed, tighten the
cap and re-check for pressure at the top
Step 7Step 5-6Step 3-4Step 1-3
of the stroke. If there is still pressure,
repeat steps 9 thru11.
6475
Spring
collar
8846
7425
Front
Preload
spacers
spring
(gold)
3.70lb
Front
Shock
.12
:: Shocks (cont.)
6473
Shock
bushing
x1
x1
.03
x1
.02
6475
Spring
cup
Build left and
!
right sides!
6475
Spring
collar
6480
Rear
spring
(green)
1.90lb
Rear
Shock
6473
Shock
bushing
8846
Preload
spacers
.25x2.12
x1
x1
.02
6475
Spring
cup
6472
Shock
mount nut
6927
4-40 x 3/4
shcs
6472
Shock
mount nut
Front x2Rear x2
6925
4-40 x 1/2
shcs
16
:: Electronics
6272
Dust cover
foam
Servo
7336
Servo
spacers
x2
3981
Ballstud
.20 short
(black)
Screw supplied
with servo
Servo horn
:: Electronics (cont.)
9180
9170
Servo
link
!
See page 40 for
correct servo
horn on the
servo chart
washer
6917
4-40 x 3/8
bhcs
7337
Gold
x4
x4
7336
Servo
mount
See page 40 for
correct servo
spacing on the
!
servo chart
x2
!
Leave a
1/16 gap
:: Electronics (cont.)
Motor
6936
Washer #4
aluminum
x2
31531
M3 x 6mm
bhcs
x2
6292
4-40 x 3/8
fhcs
!
See page 25 for
gear mesh setting
instructions.
8255
18T 48P
pinion gear
w/setscrew
Gear cover
x2
7460
w/button
(black)
6285
4-40 x 1/4
shcs
x2
:: Electronics (cont.)
17
9643
5-40 x 7/16
shcs
9877
Receiver
box
(bottom)
:: Electronics (cont.)
9878
Receiver
box
grommet
Speed Control
(ESC)
6727
Servo
tape
!
9878
Wire
grommet
plug
:: Electronics (cont.)
Receiver grommet plug
can be removed if you use
!
a personal transponder!
!
Install the ESC and servo
wires into the wire
grommet before installing
the grommet into the
receiver box!
Receiver
!
You may need to reposition
the receiver in order to
geit it to fit with the plugs
installed and the receiver
box lid installed.
Once you find a good fit,
use #6727 servo tape to
install your receiver.
18
:: Electronics (cont.)
3862
5-40 x 1/8
setscrew
9879
Thumb
knob
x2
!
6338
Antenna
and cap
9643
5-40 x 7/16
shcs
9878
Receiver
box seal
x2
:: Electronics (cont.)
9877
Receiver
box (top)
9879
4-40 x 1/2
setscrew
!
x2
!
Leave
no gap!
9879
Battery
strap
Batttery
(Not included)
!
!
9815
foam
spacer
You can trim the foam
to move the battery
pack and adjust the
weight balance of the
vehicle!
To install the battery
strap, slide the back
section in between
the top of the battery
and the bottom of the
shock tower!
9146
2-56 x 3/16
bhcs
x3
91214
SC10B
body, clear
Install left and
right sides!
:: Electronics (cont.)
Note placement of window net tab!
19
UnlockedLocked
:: Rollcage
To remove your battery pack from the vehicle, twist the thumb knobs to the
unlocked position, remove the battery strap, and then remove the battery.
When you install the battery, make sure the thumb knobs are locked before
operation.
You may need to adjust the height of the thumb knobs and/or the set
screws that the thumb knobs are attached to for your specific battery
pack type.
91204
SC10B
roll cage
side panel
(left, right)
91208
SC10B
window
nets
9146
2-56 x 3/16
bhcs
x2
Note placement of window net tab!
6927
4-40 x 3/4
shcs
6919
4-40 x 5/16
bhcs
x2
91204
SC10B
roll cage
rear panel
(left, right)
x2
Build left and
right sides!
20
:: Rollcage (cont.)
6925
4-40 x 1/2
shcs
:: Rollcage (cont.)
x2
91204
SC10B roll cage
rear body
mount bar
91204
SC10B
roll cage
hood
91204
SC10B
roll cage
front panel
(left, right)
91206
SC10B
rollcage
roof
6924
4-40 x 3/8
shcs
6927
4-40 x 3/4
shcs
4-40 x 1/2
:: Rollcage (cont.)
6925
shcs
x2
6927
4-40 x 3/4
shcs
6927
4-40 x 3/4
shcs
6927
4-40 x 3/4
shcs
6925
4-40 x 1/2
shcs
x2
6924
4-40 x 3/8
shcs
:: Rollcage (cont.)
91213
SC10B
foam body
spacer
Adhesive
!
side down!
Note placement
of foam spacer!
21
91214
SC10B body,
clear
Align holes on
body panel
for nerf bars!
:: Rollcage (cont.)
91207
SC10B lower
nerf bar
(left, right)
x2
91207
SC10B
upper
nerf bar
4-40 x 3/8
x2
6924
shcs
x2
Build left and
right sides!
22
:: Rollcage (cont.)
6292
4-40 x 3/8
fhcs
!
Do not overtighten!
It will deform the parts.
Stop turning the screw
when the gap between
the parts disappears.
:: Rollcage (cont.)
!
Do not overtighten!
It will deform the
parts. Stop turn-
ing the screw when
the gap between the
parts disappears.
6924
4-40 x 3/8
shcs
6292
4-40 x 3/8
fhcs
6924
4-40 x 3/8
shcs
:: Rollcage (cont.)
91217
SC10B cockpit underbody
(clear) and helmet
!
Install #6936
washer onto #6924
screw as shown.
Install helmet onto
cockpit.
!
9146
2-56 x 3/16
bhcs
x4
23
:: Rollcage (cont.)
6936
#4 Washer
aluminum
6924
4-40 x 3/8
shcs
6332
Body
clip
!
!
!
!
x2
!
!
Rollcage will clip into
brackets as shown.
24
:: Wheels and Tires
Note: Clean the rims and tire bead
where the two will mount to each other
before you glue them together. You
can clean them with either rubbing
alchohol, or r/c electric motor spray.
91101
KMC hex
wheel
(black)
Place the foam insert inside the tire.
Install the tire on the rim, and push the
tire beads inside the groves on the rim.
Use Tire glue #1597 (not included)
to glue the tire to the wheel. Glue one
side at a time, allowing enough time for
the glue to dry before continuing to the
Tip: You can use a rubber band to hold
the tire tight against the wheel while
CA tire glue
#1597
other side.
the glue is drying.
CA tire glue
#1597
91209
SC10B front
wheel
(black)
!
Build 2 Front!
91210
SC10B front
tire insert
SC10B front
!
Build 2 Rear!
91210
tire
w/insert
Racing Pin Tire
Soft Compound
(use on rear)
The rear tires included in this
RTR are made by JConcepts.
JConcepts tires can be
purchased at their website:
http://www.jconcepts.net
:: Wheels and Tires (cont.)
6953
8-32 steel
locking wheel
nut (low-prefile)
Build left and
right sides!
6952
8-32 steel
locking
wheel nut
25
:: Tuning Tips
Tips for Beginners:
Before making any changes to the standard setup, make sure you can get around the track without crashing. Changes
to your vehicle will not be beneficial if you can’t stay on the track. Your goal is consistent laps.
Once you can get around the track consistently, start tuning your vehicle. Make only ONE adjustment at a time, testing
it before making another change. If the result of your adjustment is a faster lap, mark the change on the included setup
sheet (make addtional copies of the sheet before writing on it). If your adjustment results in a slower lap, revert back to
the previous setup and try another change.
When you are satisfied with your vehicle, fill in the setup sheet thoroughly and file it away. Use this as a guide for future
track days or conditions.
Parts Maintenance:
Periodically check all moving suspension parts. Suspension components must be kept clean and move freely without
binding to prevent poor and / or inconsistent handling.
Recommended Gearing:
Proper motor gearing will result in maximum performance and run time while reducing the chance of overheating and
premature motor failure. The gear ratio chart lists recommended starting gear ratios for the most widely used
motor types. Gear ratios will vary depending upon track conditions, driving style, and personal preference.
Generally, you should not increase the pinion gear size more than one tooth greater than the starting size.
SC10B Gear Ratio Chart
MOTOR
17.5 Brushless Motor
13.5 Brushless Motor
10.5 Brushless Motor
3300kV Brushless Motor
Pinion
28
26
24
18
Spur
75
75
87
87
FDR
6.96 :1
7.50 :1
9.42 :1
12.57 :1
Setting Gear Mesh:
You should be able to rock the teeth of the spur gear slightly back and forth in the teeth of the pinion gear without
making the pinion gear move. If the gear mesh is tight, then loosen the #31531 motor screws and move the motor back
a little. Tighten the motor screws, then check gear mesh again. Gear mesh that is too tight or too loose can reduce
power and damage or overheat the motor or damage the teeth of the gears.
Slipper Clutch:
The assembly instructions give you a base setting for your slipper clutch. Turn the nut on the shaft so that the end of
the top shaft is even with the outside of the nut. Tighten the nut 3 more turns. At the track, tighten or loosen the nut in
1/8 turn increments until you hear a faint slipping sound for 1-2 feet on takeoffs.
Another popular way to set the clutch is to hold both rear tires firmly in place and apply short bursts of throttle.
If the clutch is properly set, the front tires should lift slightly up of f the surface.
Front Toe-In:
Zero degrees toe-in (tires pointing straight forward) is the setting that should be used in almost all track conditions.
Occasionally, adding a little bit of toe-out (tires pointing slightly out) can increase initial turn in response. A slight amount
of toe-in will increase front end stability a little and results in less aggressive steering, but this option is rarely used.
Caster:
The vehicle comes with 30 degree caster blocks (#7922). For less aggressive steering try the optional 25 degree
caster blocks (#7919).
26
:: Tuning Tips (cont.)
Front Camber:
Camber is the angle of the wheel when looked at from the front. The angle is measured from a line perpendicular to the
ground to the face of the wheel. Camber is used to ensure a wider tire contact patch while cornering. A good starting
point for the front is -1°. Performance will begin to decrease after -3°. Positive camber, where the top of the tire is
leaning out, is not recommended in the front. To set your camber use the included #1719 camber gauge.
Front Camber Links and Vertical Ballstud Adjustment:
Changing the length of the camber link is considered a bigger change than adjusting the ballstud height on the shock
tower. Shortening the camber link (or lowering the ballstud) will give the front end less roll and quicken steering
response, especially on corner entry. Lengthening the camber link (or raising the ballstud) will give the front end more
roll and slower steering response, but can produce more corner exit steering. Longer camber links are typically used
on high grip tracks and shorter links tend to work better on medium grip and loose tracks.
Rear Camber:
A good starting point for the rear camber setting is -1°. In loose track conditions, going to 0° camber can improve
straight-line acceleration.
Rear Camber Links and Vertical Ballstud Adjustment:
Changing the length of the camber link is considered a bigger step than adjusting the ballstud height on the rear chassis
brace. Shortening the camber link (or lowering the ballstud) will give the rear end less roll and the car will tend to
accelerate or “square up” better. Lengthening the camber link (or raising the ballstud) will give the rear more roll and
more cornering grip. Longer camber links are typically used on high grip tracks, while shorter links tend to work better
on medium grip and loose tracks.
Rear Hub Spacing:
There are three options for rear hub spacing, FORWARD, MIDDLE, & BACK. The kit setting provides the best possible
rear traction. The FORWARD position will provide more rear traction for low grip tracks. The BACK position will provide
more steering on high grip tracks.
Ride Height:
Ride height is the distance from the bottom of the chassis to the ground. The standard front ride height setting is with
the inner and outer hinge pins of the front arms level on the same imaginary horizontal line, or 31mm as measured from
the bottom of the chassis directly behind the skid plate. The standard rear ride height setting is with the driveshafts
slightly below level i.e., the dif f outdrives are slightly lower than the axles giving the driveshafts a small angle relative to
the ground. More specifically, the standard rear ride height is 29mm measured to the bottom of the gearbox where
it sticks through the rear chassis plate. To check ride height, lift up the entire car about 8-12 inches off the bench
and drop it level. After the suspension “settles” into place, add or remove pre-load clips until the desired ride height is
achieved. For precise ride height measurements, use the Factory Team ride height gauge #1449.
Anti-Squat:
Anti-squat denotes the angle of the rear arms relative to the ground. The kit setting is 2 degrees and can be adjusted
to 1 degree by removing the included 2 degree shim below the rear arm mount and replacing it with a 1 degree shim.
Changing to less anti-squat tends to make the truck produce more rear traction and less steering in the corners.
Shock Piston and Fluid:
The SC10B’s shocks are built with our 2 hole, #1 pistons in the front and our #3 pistons in the rear.
All pistons have a number molded on them (use a black marker to color in the numbers for easy identification).
As a rule of thumb, larger hole pistons decrease damping which can help the vehicle in bumpy and low-grip situations.
On smoother tracks, or for large jumps, you may want to use a smaller hole piston which will increase damping and take
away some grip. [#1 large hole, #2 medium hole, #3 small hole]
Typically, your SC10B shocks will work best with shock fluid rates between 25 and 35 wt (275 - 425 CST).
Use the thicker weight fluids when changing to larger hole pistons. Use the thinner weight fluids when changing to
smaller hole pistons.
Setup Sheets:
Often, the best way to get your car handling right is to use one of the setups from our website as a starting point.
Go to www.rc10.com and click on the links to Setup Sheets, then SC10B setups. Our team of professional drivers helps
develop these setups at National events. Most drivers have a “base” setup that they use as a starting point for every
event. Try running some of our base setups OR look for track conditions and tires that are similar to your local track and
mimic that setup. Remember, each adjustment has a purpose, so copy everything from the setup sheet and then make
adjustments based on the recommendations in here and in our online tuning guide.
27
:: Shocks
5407
6299
6441
6458
6459
6465
6466
6469
6473
6475
6925
6927
7217
7484
8846
9884
9885
9884 (F)
9885 (R)
Red O-Rings
1/8” E-Clips
Shock Cap, Molded
Shock Shaft, 1.32“ stroke
Shock Shaft, 1.02” stroke
Shock Pistons, 4 each
Shock Down Stops, Set
Black Shock Cap O-Ring
Shock Bushings
Preload Spacers 5 thicknesses,
Collars & Cups, 4 each
4-40 x 1/2“ SHCS
4-40 x 3/4” SHCS
Shock Rod Ends / Plastic Pivot Balls
V2 1/10 Shocks Rebuild Kit
Preload Spacers, 4 each
V2 RTR Front Shock Bodies 1.02“
V2 RTR Rear Shock Bodies 1.39”
FT Truck Front Spring Kit. I pair of green,
silver, blue, gold, and red front springs
FT Truck Front Spring Kit. I pair of green,
silver, blue, gold, and red rear springs
Rear Spring Silver 2.10 lb
Rear Spring Green 1.90 lb (Kit)
Rear Spring Black 1.74 lb
Rear Spring Gray 2.33 lb
Front Spring Gold 3.70 lb (Kit)
Front Spring Black 2.765 lb
Front Spring Green 2.99 lb
Front Spring Silver 3.225 lb
Front Spring Blue 3.45 lb
Front Spring Red 3.90 lb
Rear Spring Blue 2.55 lb
Rear Spring Gold 2.75 lb
Rear Spring Red 2.95 lb
Ball Bearing, 3/16” x 3/8“
4-40 x 1 1/4” SHCS
4-40 x 1/2” SHCS
4-40 x 1” SHCS
Idler Gear, molded
Idler Gear Shaft
B4/T4 Motor Plate
B4/T4 Top Shaft
B4/T4 Top Shaft Spacer
Ball End Washer
SC10 Transmission Case (left & right)
Ball Bearing, 10 x 16mm
9600
3977
9602
9826
9832
9360
9361
9832
9826
9601
:: Slipper Clutch / Pinions
6285
6629
7460
7461
7485
7486
9603
9650
9651
9652
9653
9654
7485
4-40 x 1/4 SHCS
5-40 Locknuts
Molded B4/T4 Gear
Cover, black (Kit)
Molded B4/T4 Gear
Cover, clear
V2 Slipper Hubs
V2 Slipper Spring
and Washer
B4/T4 Slipper Pad
75T 48P Spur Gear
81T 48P Spur Gear
78T 48P Spur Gear
84T 48P Spur Gear
87T 48P Spur Gear
(Kit)
Ballstud .20” Black (short)
Foam Ballend Dust Cover
4-40 x 3/8” FHCS
4-40 x 3/8” BHCS
Turnbuckle 2.80”
Ballcups, large
Turnbuckle 2.62”
Servo Mount Set
Gold Washer
B4 / T4 Servo Link
Servo Horns Set
6
28
6
6
Pr.
12
Pr.
1
4
1
1
6917
9180
7337
3981
7336
6272
7230
7664
7666
6582
Steering
servo link
9170
9170
9170
Front Camber
Turnbuckle
7253
Steering Turnbuckle
Rear Camber Turnbuckle
6575
7230
6917
7337
6292
7230
7101
7230
:: Steering
2221
3856
6272
6276
6925
9566
9610
9640
9657
9659
4-40 x 7/16” BHCS
Steering Bushings, Set
Foam Ball end Dust Covers
Ballstud .20” Silver (short)
4-40 x 1/2” SHCS
B4 / T4 Top Plate
Servo Saver / Steering Hardware
B4 / T4 Steering Bolt, left & right
B4 / T4 HD Servo Saver Spring
B4 / T4 Steering Set. Includes Rack,
Bellcrank, Servo Saver, Steering Brace
6
1
28
6
6
1
1
1
1
1
6276
9659
2221
9659
2221
6727
6276
69256925
9566
3856
9659
3856
29
3856
6925
9610
9610
9657
6727
9610
6276
9659
9659
:: Front Shock Tower
6272
6277
6292
6295
6917
6924
6927
9630
91202
91212
Foam Ballend Dust Covers
Ballstud .30” long (silver)
4-40 x 3/8 FHCS
4-40 Nuts
4-40 x 3/8 BHCS
4-40 x 3/8 SHCS
4-40 x 3/4 SHCS
Ballstud Washer
SC10B Front Shock Tower
SC10B Body Mounts, front & rear
28
6
6
6ea
6
6
6
10
1
1ea
9640
6272
6277
6927
6917
9659
3856
9640
6295
6292
6292
6924
6924
9630
6924
6917
6924
91202
6277
9630
6295
6272
91212
30
:: Front Bumper
2221
6915
91200
91220
4-40 x 7/16 BHCS
4-40 x 5/8 FHCS
SC10B Front Bumper Set
4-40 x 1 5/8 SHCS
6
6
1
6
2221
2221
91200
91200
91220
91200
:: Front Suspension
3977
3983
4187
4449
6272
6277
6953
7260
7368
7369
7922
9621
9622
9645
9880
9881
9882
9883
91201
3/16 x 3/8 RS Ball Bearing
Ballstud .30” short (black)
.030” Nylon Washers
4-40 x 3/16 Aluminum Locknut
Foam Ballend Dust Covers
Ballstud .30” Silver, short
8-32 Low Profile Steel Locknut
4-40 Small Plain Nut
3/16” Axle Shim
1/16” Universal Roll Pins
30D Caster Blocks L&R
Front / Rear Inner Hinge Pins
Hinge Pin Set, outer, & King Pin
2-56 x 1/8 BHCS
SC10 Steering Blocks, Hex
SC10 Front Axle & C-Clips, Hex
C-Clips, 3/16”
SC10 Wheel Hex Adapters, Set
SC10B Front Arms
12
28
12
14
Pr.
Pr.
Pr.
6915
2
6
5
6
6
4
1
1
6
2
6
1
6272
9645
3983
7922
9622
7260
9881
9880
3977
9882
6272
6277
4187
3977
7369
6953
4449
7368
9621
91201
9883
9645
7922
9622
:: Battery Strap
9815
9879
SC10 Foam Battery Spacer
SC10 Battery Strap, Thumb
Screws, and Setscrews
31
1
1
9879
:: Chassis / Radio Tray
3862
4334
6272
6277
6338
6915
6919
6922
6924
7487
9269
9563
9564
9630
9643
9645
9765
9818
9819
9823
9877
9878
91205
5-40 x 1/8” Set Screw
2-56 x 5/16” BHCS
Foam Ballend Dust Cover
Ballstud .30” Silver (long)
Antenna Tube (black)
4-40 x 5/8” FHCS
4-40 x 5/16” BHCS
4-40 x 1/2” FHCS
4-40 x 3/8” SHCS
Arm Mounts, 2.5, 3, 3.5, 4
5-40 x 1/2” FHCS
B4 / T4 / GT2 Front Bulkhead
RR / FR Hinge Brace
.030 Ballstud Washer
5-40 x 7/16” SHCS
2-56 x 1/8” BHCS
4-40 x 7/16 FHCS
SC10 Arm Mount / Chassis Plate
SC10 Rear Motor Guard
SC10 Chassis
SC10 Receiver Box
SC10 Receiver Box Seals
SC10B Roll cage Bracket
6
8
28
4
1
6
6
6
6
1
6
1
1
10
6
8
6
1
1
1
1
1
2
7487
7487
9879
9879
9645
9879
9818
9819
9879
6919
6922
9643
9877
9878
9878
9877
9765
9815
3862
9643
9643
9564
9643
6277
9630
6338
6924
6272
6272
6277
9630
9269
4334
4334
9564
6915
9563
91205
9823
9643
9765
91205
32
:: Rear Shock Tower
6927
6928
7260
9643
9644
9824
91212
4-40 x 3/4” SHCS
4-40 x 1” SHCS
4-40 Plain Nut
5-40 x 7/16” SHCS
5-40 x 9/16” SHCS
T4 / SC10 Rear Shock Tower
SC10B Body Mounts, front & rear
SC10 Tires w/Foam Inserts
1/8 Molded Tire Inserts
KMC Hex Wheels, Black (Kit)
KMC Hex Wheels, Silver
KMC Hex Wheels, Chrome
KMC Hex Wheels/Tire Black
KMC Hex Wheels/Tire Silver
KMC Hex Wheels/Tire Chrome
SC10B Front Wheels Hex, Black
SC10B Front Tires w/ Foam Inserts
SC10B Front Wheels/Tire Black
SC10B Front Wheel Hex, Chrome
SC10B Front Wheels/Tire Chrome
91203
6915
2
2
2
2
2
2
2
2
2
2
2
2
2
6915
91209
6913
6924
6924
6932
91101
:: Body and Driver
6924
6936
9146
91213
91214
91215
91216
91217
91218
91219
6924
4-40 x 3/8” SHCS
#4 Washer, Aluminum
2-56 x 3/16” BHCS
SC10B Foam Body Spacers
SC10B Body, clear
SC10B Team AE Body, pre-painted
SC10B Blue AE Body, pre-painted
SC10B Cockpit Underbody w/Driver, clear
SC10B Blue AE Body Decals
SC10B Team AE Body Decals
6936
6
10
6
2
1
1
1
1
1
1
91217
9146
91210
91213
Soft compound
pin tire
91210
9146
91214
9146
91214
34
:: Roll Cage
6292
6919
6924
6925
6927
9146
91204
91206
91207
91208
4-40 x 3/8” FHCS
4-40 x 5/16” BHCS
4-40 x 3/8” SHCS
4-40 x 1/2” SHCS
4-40 x 3/4” SHCS
2-56 x 3/16” BHCS
SC10B Rollcage
SC10B Roll cage Roof
SC10B Nerf Bars, left & right
SC10B Window Nets, left & right
FT T4 Ti Turnbuckle Set
FT Ti Turnbuckle, 2.65” (blue) for front steering
FT Ti Turnbuckle, 1” (sway bar) (blue)
FT Ti Turnbuckle, 2.80” (blue)
FT B4 Aluminum Trailing Axle,
requires # 9581, 4187 (Not for hex wheels)
FT Blue Aluminum Shock Caps, (blue)
FT Solid Axle Pins
FT Blue Body Clip, 4 long, 6 short
FT Blue Body Clip, long
FT Blue Body Clip, short
FT Milled Aluminum Motor Plate, (blue)
Blue Aluminum Shock Ball Ends with Eyelets, Set
FT Milled Aluminum Motor Plate, (black)
FT Servo Mounts, blue aluminum
FT Blue Aluminum Threaded Shock Bushings
FT Rear Shock Bushing (short)
FT Battery Strap Thumb Screws, Set
8-32 LP Locknuts (blue)
Steering Rack Bearings
Gold Shock Shaft, 1.32” stroke
Gold Shock Shaft, 1.02” stroke
Bleeder Shock Caps, 1/10
Shock Pistons, Blank
3/32“ Ceramic Diff Balls
Ball Bearing, PTFE Sealed 3/16 x 3/8”
FT 4-40 Aluminum Locknuts (blue)
FT 8-32 Aluminum Locknuts (blue)
CVD/CVA Rebuild Kit
FT Threaded Shock Collar & O-Rings
T4 Rear A-Arm, Carbon
CVD Axle Bone T4 (black)
CVD Set T4
FT V2 1.02” Threaded Shocks Kit
FT V2 1.02” Threaded Shock Bodies
FT V2 1.39” Threaded Shocks Kit
FT V2 1.39” Threaded Shock Bodies
FT Vented V2 Slipper Hubs
Caster Block 30 deg, (left & right) (Kit)
Crush Tube (for use with FT Aluminum Hubs Only)
.187 x .50 x .196 Bearing
(for use with FT Aluminum Hubs Only)
Aluminum Front Bulkhead (blue)
B4 / T4 Chassis Brace, Hinge Pin Brace, Carbon
B4 / T4 Top Plate, Carbon
B4 / T4 Caster Block 20 deg, (left & right)
FT SC10 / T4 CVA Bones, requires #9755
CVD Axles B4, T4, SC10
FT B4 / T4 Aluminum Motor Plate (blue)
RR Axle Wheel Spacer (silver)
B4 / T4 Blue Servo Saver Bolt
B4 / T4 Sway Bar Kit.
FT B4 / T4 Aluminum Hinge Pin Brace V2
T4 Shiny CVD Dogbone, requires #9598
FT SC10 / T4 CVA Set
CVA Axle, Rear B44, B4, T4, SC10
SC10 / B4 FT Ti Front Axles, Set,
requires # 9581, 4187 (Not for hex wheels)
Ti Nitride Ballstuds 4-40 x .20 - long
Ti Nitride Ballstuds 4-40 x .30 - long
Ti Nitride Ballstuds 4-40 x .40 - long
Ti Nitride Ballstuds 4-40 x .20 - short
Ti Nitride Ballstuds 4-40 x .30 - short
SC10 Battery Strap, Carbon
FT Aluminum Hub, 0 deg
(requires #7933, #7935, #6906)
FT Aluminum Hub, 0.5 deg
(requires #7933, #7935, #6906)
FT Aluminum Hub, 1 deg
(requires #7933, #7935, #6906)
FT Aluminum Hub, 1.5 deg
(requires #7933, #7935, #6906)
FT Aluminum Hub Tower Set
FT Aluminum Hub Tower C, carbon fiber
Aluminum Ballstud Washers, blue
M3 Aluminum Locknuts, blue
Hi -Torque Slipper Pad
VTS Slipper Conversion
VTS Slipper Housing
VTS Slipper Pads
VTS Slipper Plate
VTS Slipper Hub, Outer
12 x 27.5 Threaded Shock Body
12 x 36 Threaded Shock Body
12mm Shock Cap
12mm Threaded Collar and O-Ring
27.5 x 3 TiN Shock Shaft (front)
35 x 3 TiN Shock Shaft (rear)
12mm Shock Piston, (1.5, 1.6, 1.7)
12mm Shock Rebuild Kit
12mm Shock Spring Cups (+0mm, +5mm, +9mm)
12mm Shock Kit (SC10, T4 fr - all model versions)
12mm Shock Kit (SC10, T4 rr - all model versions)
12mm Front Spring Brown 2.85
12mm Front Spring Black 3.00
12mm Front Spring Green 3.15
12mm Front Spring White 3.30
12mm Front Spring Gray 3.45
12mm Front Spring Blue 3.60
12mm Front Spring Yellow 3.75
12mm Front Spring Red 3.90
12mm Front Spring Orange 4.05
12mm Front Spring Purple 4.20
12mm Rear Spring Black 1.90
12mm Rear Spring Green 2.00
12mm Rear Spring White 2.10
12mm Rear Spring Gray 2.20
12mm Rear Spring Blue 2.30
12mm Rear Spring Yellow 2.40
12mm Front Soft Spring Kit (3 pair)
12mm Front Medium Spring Kit (3 pair)
12mm Front Hard Spring Kit (3 pair)
12mm Rear Soft Spring Kit (3 pair)
12mm Rear Medium Spring Kit (3 pair)
DS1903/S1903 Metal Gear Set
S1903MG Servo
DS1903MG Servo
XP SC900-BL Brushless ESC
XP ESC Fan Option
XP SC700-BL Brushless ESC
XP SC1200-BL Brushless ESC
XP SC1300-BL Brushless ESC
Wall Charger, 120V 350MaH
XP DS1313 Digital Servo
XP DS1015 Digital Servo
Gear Set, DS1313
Gear Set, DS1015
Servo Case , DS1313 / DS1015
Accessory Pack, DS1313 / DS1015
TRS403-SSi 2.4GHz 4Ch Receiver
XP2G 2.4GHz Radio System
XP3G 2.4GHz Radio System
TRS402-SSi 2.4GHz 4Ch Receiver
XP2-SSi 2.4GHz Radio System
XP3-SSi 2.4GHz Radio System
35
Pr.
1
Pr.
1
6
2
1
1
2
1
1
2
2
2
2
1
1
4ea.
1
4ea.
2
2
Pr.
Pr.
Pr.
Pr.
Pr.
Pr.
Pr.
Pr.
Pr.
Pr.
Pr.
Pr.
Pr.
Pr.
Pr.
Pr.
Replacement Rotor 540-SL
540-SL Brushless Motor 3300kV
540-SL Brushless Motor 3900kV
540-SL Brushless Motor 4900kV
540-SL Brushless Motor 6100kV
Sonic 540 21.5 Competition Brushless Motor
Sonic 540 17.5 Competition Brushless Motor
Sonic 540 17.5 Replacement Stator
Sonic 540 13.5 Competition Brushless Motor
Sonic 540 10.5 Competition Brushless Motor
Sonic 540 9.5 Competition Brushless Motor
Sonic 540 8.5 Competition Brushless Motor
Sonic 540 7.5 Competition Brushless Motor
Sonic 540 6.5 Competition Brushless Motor
Sonic 540 5.5 Competition Brushless Motor
Sonic 540 5.0 Competition Brushless Motor
Sonic 540 4.5 Competition Brushless Motor
Sonic 540 4.0 Competition Brushless Motor
Sonic 540 3.5 Competition Brushless Motor
Sonic 540 Stock Rotor 12.3 x 24.2 (7.25)
Sonic 540 Stock Rotor 12.3 x 25.0 (7.25)
Sonic 540 Stock Rotor 12.5 x 25.0 (7.25)
Sonic 540 Modified Rotor 12.2 x 25.0 (5.0)
Sonic 540 Modified Rotor 12.5 x 25.0 (5.0)
Sonic 540 Modified Rotor 12.5 x 25.0 (5.0)
Motor Cooling Fans (2)
Charge Harness 2S Standard Pack 4mm
4.0mm plugs (2M, 2F)
4.0mm plugs (2M, 10F)
4.0mm plugs (10F)
4.0mm plugs (10M)
3.5mm plugs (3M, 3F)
3.5mm plugs (10F)
Sonic 540/550 Sensor w/Bearing
Sonic 540/550 Insulator Set (2 pcs.)
Sonic 540/550 Timing Cap w/Screws
Sonic 540 Case Screws (3 pcs.)
Sonic 540 Steel Bearing Set
Sonic 540 Ceramic Bearing Set
540-SL/550-SL Steel Bearing Set
540-SL/550-SL Ceramic Bearing Set
Flat Sensor Wire 70mm
Flat Sensor Wire 110mm
Flat Sensor Wire 150mm
Flat Sensor Wire 200mm
Flat Sensor Wire 270mm
Sonic 540 Rotor Spacers
:: LRP Speed Controls
1
LRP80230
1
LRP80250
1
LRP80960
1
LRP80970
1
1
1
:: LRP Brushless Motors / Combos
1
LRP50430
1
LRP50440
1
LRP50450
1
LRP50460
1
LRP50480
1
LRP50643
1
LRP50644
1
LRP50654
1
LRP50664
1
LRP50674
1
LRP50684
1
LRP50689
1
LRP50694
1
LRP50704
1
LRP80741
1
LRP80742
1
LRP80743
1
Spin Super Brushless
Spin Pro Brushless
Flow Competition
Flow Works Team
Quadra Pro 2 Charger
Pulsar Touch Competition Charger
LiPo Balance Board XH
LiPo Balance Board FP/TP
LiPo Balance Board PQ
Pulsar Touch Temperature Sensor
Pulsar Touch Sensor Wire Splitter
LRP Competition 20A Power Supply
LRP 2in1 LiPo Guard + BEC
LiPo Parallel Balancer
High Power Solder Station
Soldering Tip 5mm
Soldering Tip 1.2mm
Soldering Handle
LRP Speedo Updater Spec 2
X-12 Optional Ceramic Ball Bearings
X-12 Small Parts Set
X-12 PreciSensor Unit
X-12 Alum Rear Cover
X-12 12.0mm Sintered Rotor
X-12 13.0mm Sintered Rotor
X-12 Stock Spec Rotor 12.45mm
Works Team X-12 12.0mm Rotor
Works Team X-12 12.5mm Rotor
Works Team X-12 13.0mm Rotor
X-12 Stock Spec 1S LiPo Rotor
BEC Stabilizing Capacitor
SXX Low Profile Fan
30mm Motor Fan/Clamp, Gunmetal
Radical Cooling Set, Blue
SXX Power Cap 3.7-4.8V
SXX Power Cap 6.0-7.4V
70mm High Flex Sensor Wire
100mm High Flex Sensor Wire
150mm High Flex Sensor Wire
200mm High Flex Sensor Wire
Reedy 09’ White T-Shirt (M, L, XL, 2XL, 3XL)
Reedy 09’ Black T-Shirt (M, L, XL, 2XL, 3XL)
Reedy 2012 T-shirt - Black (S, M, L, XL, 2XL, 3XL)
Reedy Trucker Hat
Reedy Patch
AE Stencil Blue T-Shirt (S, M, L, XL, 2-6XL)
AE Stencil Gray Sweatshirt (S, M, L, XL, 2XL, 3XL)
AE 26 Time World Championship T-Shirt, Black
(S, M, L, XL, 2XL, 3XL)
Associated Windbreaker (S, M, L, XL, 2XL, 3XL)
Associated Winter Jacket (S, M, L, XL, 2XL)
AE Long Sleeve T-Shirt (S, M, L, XL, 2XL)
AE White T-Shirt (S, M, L, XL, 2XL, 3XL, 4XL)
AE Blue T-Shirt (S, M, L, XL, 2-6XL)
AE Black T-Shirt (S, M, L, XL, 2XL, 3XL, 4XL)
AE 2012 T-Shirt, Blue (S, M, L, XL, 2XL, 3XL)
AE 2012 T-Shirt, White (S, M, L, XL, 2XL, 3XL)
AE 2012 T-Shirt, Black (S, M, L, XL, 2XL, 3XL)
AE Hat 11’ Flat Bill Black S/M
AE Hat 11’ Flat Bill Black L/XL
26 Time World Championship Hat S/M
26 Time World Championship Hat L/XL
1/10 FT Motor Bag
Factory Team 1/10 Car Carrier Bag
AE Pit Gloves (M, L, XL)
AE 2012 Hat, Black, Flat Bill, S/M
AE 2012 Hat, Black, Flat Bill, L/XL
AE 2012 Hat, Black, Curved Bill, S/M
AE 2012 Hat, Black, Curved Bill, L/XL
AE 2012 Hat, White, Flat Bill, S/M
AE 2012 Hat, White, Flat Bill, L/XL
AE 2012 Hat, White, Curved Bill, S/M
AE 2012 Hat, White, Curved Bill, L/XL
Reedy 2009 Track Banner
Reedy 09 Decal Set
Team Associated Track Banner
Replay XD1080 Complete Camera System
Replay XD720 Complete Camera System
Replay XD1080 Lens Bezel Kit
Replay XD1080 Clear Lens Cover
Replay XD1080 Lens Bezel & Rear Cap O-Ring
Replay XD1080 HDMI to Mini-HDMI
Replay XD1080 Mini 8-pin USB Charge Data Cable
USB DC Car Charger 1A Stubby
USB DC Car Charger 500mAh
Micro SDHC USB Reader
3M VHB 4991 Mount Adhesive for SnapTray
3M VHB 5962 Mount Adhesive for Pro Flat Mount
3M VHB 5962 Mount Adhesive for SnapTray
Replay XD Suction Cup Arm Mini Clamp
Replay XD Suction Cup Short Arm Base
Replay XD Skateboard Mount
Replay XD VHB SnapTray, Convex
Replay XD VHB SnapTray, Flat
Au Plug for Universal DC Wall Charger
Eu Plug for Universal DC Wall Charger
Uk Plug for Universal DC Wall Charger
Universal USB DC Wall Charger 1A
:: 1/8 Kits and RTR’s
20501
20502
20503
20504
80905
1
80906
1
80907
1
80908
1
80912
1
1
80933
1
1
80934
1
1
1
1
1
1
1
1
1
1
1
1
1
1
MGT 4.60 SE RTR (ready-to-run)
MGT 8.0 Nitro RTR (ready-to-run)
Limited Edition MGT 4.60 Nitro RTR, w/flag body
(ready-to-run)
Limited Edition MGT 8.0 Nitro RTR, w/flag body
(ready-to-run)
RC8RS “Race Spec” Nitro Buggy RTR (ready-to-run)
RC8.2 Nitro Buggy FT Kit
RC8.2e Electric Buggy FT Kit
RC8.2e Electric Buggy RTR (ready-to-run)
RC8T Championship Edition
RC8T-RS “Race Spec” Nitro Truggy RTR (ready-to-run)
SC8.2e Short Course Race Truck, Rockstar/Makita
Electric RTR (ready-to-run)
SC8.2e Short Course Race Truck, Slick Mist Electric
RTR (ready-to-run)
FT Turnbuckle Wrench
FT Ride Height Gauge
FT Hex Driver Set, (7 pcs)
FT .050” Silver Hex Driver
FT 1/16” Black Hex Driver
FT 1.5mm Purple Hex Driver
FT 5/64” Blue Hex Driver
FT 3/32” Gold Hex Driver
FT 2.5mm Green Hex Driver
FT 3mm Red Hex Driver
FT Screwdriver Set
FT Phillips Silver Screwdriver
FT Silver Spring Hook Tool
FT Nut Driver Set, (6 pcs)
FT 3/16” Black Nut Driver
FT 1/4” Red Nut Driver
FT 5.5mm Red Nut Driver
FT 11/32” Green Nut Driver
FT 7.0mm Silver Nut Driver
FT 8mm Gold Nut Driver
FT 5/64” Blue Ball Hex Driver
FT 3/32” Gold Ball Hex Driver
FT Ball Hex Driver Set, (3 pcs)
FT 8-Piece 1/4” Hex Drive Set
FT 1/4” Hex Drive Handle, without tips
FT 1/4” Hex Drive .050” Tip
FT 1/4” Hex Drive 1/16” Tip
FT 1/4” Hex Drive 5/64” - 2.0mm Tip
FT 1/4” Hex Drive 3/32” Tip
FT 1/4” Hex Drive 1.5mm Tip
FT 1/4” Hex Drive 2.5mm Tip
FT 1/4” Hex Drive 3/16” Nut Driver Tip
FT 1/4” Hex Drive 1/4” Nut Driver Tip
FT 1/4” Hex Drive 11/32” Nut Driver Tip
FT 1/4” Hex Drive 5.5mm Nut Driver Tip
FT 1/4” Hex Drive 7.0mm Nut Driver Tip
FT 1/4” Hex Drive 8.0mm Nut Driver Tip
FT 1/4” Hex Drive 5/64” - 2.0mm Ball End Tip
FT 1/4” Hex Drive 3/32” Ball End Tip
FT 1/4” Hex Drive Standard Screwdriver Tip
FT 1/4” Hex Drive Phillips Screwdriver Tip
FT 1/4” Hex Drive 2.5mm Ball End Tip
FT 1/4” 5 Piece Power Tool Tips Set (5/64-2.0mm,
1.5mm, 2.5mm, 5/64”- 2.0mm ball, 2.5mm ball)
FT Camber + Track Width Tool
FT Body Scissors
12 Inch Nylon Wire Ties
6 Inch Nylon Wire Ties
8 Inch Nylon Wire Ties
FT Droop Gauge
Shock Building Tool
Molded Tools, Set
4 Inch Nylon Wire Ties