Page 1
Page 2
2
:: Introduction
Thank you for purchasing this Team Associated product. This assembly manual contains instructions and tips for building and
maintaining your new RC10B5M Team Kit. Please take a moment to read through this manual to help familiarize yourself with
these steps.
We are continually changing and improving our designs; therefore, actual parts may appear slightly different than in the
illustrations. New parts will be noted on supplementary sheets located in the appropriate parts bags. Check each bag for these
sheets before you start to build.
:: KIT Features
Features in the RC10B5M Team Kit:
• Narrowed hard anodized aluminum chassis with centralized mass and mid-motor position for improved handling on high grip
off road tracks
• Chassis fits R.O.A.R. approved 2S saddle packs and 2S short packs using optional foam insert
• V2 12mm “Big Bore” threaded aluminum shocks with 3mm shafts and updated O-rings for improved smoothness
• VTS (Variable Torque multi-plate Slipper) with 3 drive surfaces and high-resolution spring
• New transmission has stronger gears, precision ball bearings, and a 14 carbide ball differential for increased life and torque
capacity
• Adjustable front suspension mount angle (kick-up) options of 25˚ and 30˚
• New Gullwing front suspension features heavy duty steering and caster blocks, while the insert system allows for easy caster and
trailing axle adjustments
• One piece front axle/hex adapter and larger front wheel bearing for added durability
• Updated full bearing steering system with horizontal ball studs for finer Ackermann adjustments
• Heavy-duty ball cups and ball studs allow for maximum suspension travel while reducing binding and friction
• Rear hubs feature larger bearings as well as the quick and easy insert system to adjust camber link position and rear toe-in.
• B5M clear body and wing included
:: Additional
Your new B5M Team Kit comes unassembled
and requires the following items for completion
(refer to catalog section for suggestions):
• R/C two channel surface frequency radio system
• AA-size batteries for transmitter
(#302 alkaline, #303 rechargealble)
• Electronic Speed Control, ESC (#29140, #29143)
• Steering servo (#29166, #29167) • R/C electric motor
• Pinion gear, size determined by type/wind of motor
• Battery charger (a peak detection charger, or LiPo compatible charger)
• 6 cell NiMH battery pack (#700) or a 2 cell LiPo battery pack (#714)
• Calipers or a precision ruler • Needle nose pliers
• Lexan specific spray paint
• Reamer / hole punch
• Cyanacrylate glue (#1597)
• Thread locking compound (#1596)
• Tires and Inserts, Fronts and Rears
Tools included:
• Allen wrenches 1.5mm, 2.0mm
• #1113 12mm Shock Tool
• Multi-wrench
:: Other Helpful Items
• Silicone Shock Fluid (Refer to catalog for complete listings)
• Body Scissors (AE Part # 1737) • Reamer / Hole Punch • Wire Cutters • Hobby Knife
• FT Hex Wrenches (AE Part # 1655) • Needle Nose Pliers • Multi Tool (AE Part #7494)
• Soldering Iron • Calipers or a Precision Ruler • Green Slime shock lube (AE Part # 1105)
Associated Electrics, Inc.
26021 Commercentre Dr.
Lake Forest, CA 92630
http://www.TeamAssociated.com · http://www.RC10.com · http://twitter.com/Team_Associated · http://bit.ly/AEonFacebook
Customer Service
Tel: 949.544.7500
Fax: 949.544.7501
Page 3
12/13
:: Table of Contents
1................... Cover
2................... Introduction
3................... Table of Contents
3
11 - 12........Turnbuckles Build
(Bag H-HH)
12 - 14........ Shocks Build
(Bag I-II)
4 - 5..............Front Top Plate and
Steering Build
(Bag A-AA)
5 - 6..............Front Arms and Uprights Build
(Bag B)
6 - 7.............. Shock Towers and Rear
Chassis Brace Build
(Bag C)
8................... Differential Build
(Bag D-DD)
9................... Gearbox Build
(Bag E)
9 - 10.......... Slipper Build
(Bag F-FF)
10 - 11.........Rear Hub and CVA Build
(Bag G)
14 - 16........Electronics Build
(Bag J)
16 - 17.........Wheels, Tires, and Body Build
(Bag K)
18 - 20....... Tuning Tips
21 - 29....... Catalog
30................ Notes / Contact Info
31................ Setup Sheet “Kit Setup”
32................ 1:1 Hardware “Fold Out”
33................ Setup Sheet “Blank”
34................ Back Cover
:: Notes
This symbol indicates a special
note or instruction in the manual.
!
There is a 1:1 hardware foldout page in the back
of the manual. To check the size of a part, line
This symbol indicates a Racers Tip.
Associated Electrics, Inc.
26021 Commercentre Dr.
Lake Forest, CA 92630
http://www.TeamAssociated.com · http://www.RC10.com · http://twitter.com/Team_Associated · http://bit.ly/AEonFacebook
up your hardare with the correct drawing until
you find the exact size. Each part in the foldout
has a number assigned to it for ordering
replacement parts.
Customer Service
Tel: 949.544.7500
Fax: 949.544.7501
Page 4
4
:: Front Top Plate and Steering Build - Bag A - AA - Step 1
91048
5407
Red
O-Ring
x2
Heavy-duty
Ballstud,
8mm
!
Note orientation
of steering rack.
:: Front Top Plate and Steering Build - Bag A - AA - Step 2
x2
91475
3 x 7 x 3
Ball Bearing
FT Ballstud
x4
31286
Washer,
aluminum
(2mm)
91391
Steering
Rack
M3 x 12mm
x2
91391
Steering
Bellcrank
89202
BHCS
!
Brace
x2
Do not overtighten steering bolts. Make sure
there is free movement in the steering rack.
91047
Heavy-duty
Ballstud,
6mm
!
Note orientation
of the brace.
91362
B5 Top
Plate
25189
M3 x 22mm
BHCS
x2
91475
3 x 7 x 3
Ball Bearing
91391
Steering
Bellcrank
Brace
x4
:: Front Top Plate and Steering Build - Bag A - AA - Step 3
25202
M3 x 10mm
FHCS
x4
!
91512
RC10B5M
Front Chassis
Plate
25202
M3 x 10mm
FHCS
x5
91510
RC10B5M
Chassis
Remove any flashing
materieal from part
#91512 to ensure a
smooth fit to
part #91514.
91514
RC10B5M
Chassis
Cradle
25201
M3 x 8mm
FHCS
x6
Page 5
:: Front Top Plate and Steering Build - Bag A - AA - Step 4
91364
Bulkhead
(25 °)
25202
M3 x 10mm
FHCS
!
There are two
bulkheads included
(25 °, 30 °). 25 ° is
the standard one
used.
M3 x 16mm
:: Front Arms and Uprights Build - Bag B - Step 1
31530
M3 x 5mm
BHCS
25237
5 x 10 x 4
Bearing
M3 Locknut,
x2
25215
black
Build 2 (1 left, 1 right)
91047
Heavy-duty
Ballstud,
6mm
Front Axle
Crush Tube
91407
91404
Steering
Block
91406
Front
Axles
91404
Steering
Block Insert
(2-4)
x2
25204
FHCS
x2
x2
Trailing Axle Inserts
2
!
There are multiple options for the
trailing axle inserts. 4mm is the
standard setting. Make sure the
arrow is pointing forward for your
desired selection. Also make sure
both the right and left sides are on
4
the same setting.
5
:: Front Arms and Uprights Build - Bag B - Step 2
!
There are two
caster block inserts
included (0°, 5 °). 5 ° is the
standard one used.
You can install an
optional #4670 set
screw to better hold
the caster block inserts
and hinge pin.
91049
Heavy-duty
Ballstud,
10mm
91400
Caster
Block Insert
(5°)
4670
M3 x 8mm
Set Screw
(not included in kit)
M3 Locknut,
25215
black
31520
M2.5 x 6mm
BHCS
(not included in kit)
91400
Caster
Block
You can install an
optional #31520
screw to use as a
steering stop setting.
Build 2 (1 left, 1 right)
Page 6
6
:: Front Arms and Uprights Build - Bag B - Step 3
x2
91400
Caster Block
Spacer
91394
Hinge Pin
(front, outer)
91526
RC10B5M
Front Arms
31510
M2 x 4mm
BHCS
x2
89202
M3 x 12mm
BHCS
91402
Caster
Block
Bushing
x2
Build 2 (1 left, 1 right) Build 2 (1 left, 1 right)
:: Shock Towers and Rear Chassis Brace Build - Bag C - Step 1
91410
Front
Bumper
31521
M2.5 x 8mm
BHCS
x2
91371
Front Hinge
Pin Brace
91394
Hinge Pin
(front, Inner)
25204
M3 x 16mm
FHCS
x2
:: Shock Towers and Rear Chassis Brace Build - Bag C - Step 2
89204
M3 x 24mm
BHCS
31286
FT Ballstud
Washer,
aluminum
(2mm)
Front Shock
x2
x2
91516
RC10B5M
Tower
91477
M3 Nut
(black)
Ballstud, 10mm
x2
91049
Heavy-duty
x2
89202
M3 x 12mm
BHCS
x4
Page 7
:: Shock Towers and Rear Chassis Brace Build - Bag C - Step 3
7
25215
M3 Locknut,
black
91532
RC10B5M
Arm Mount,
C (3+1)
25202
M3 x 10mm
FHCS
x2
x2
RC10B5M
Rear Arms
91532
RC10B5M
Arm Mount, D
:: Shock Towers and Rear Chassis Brace Build - Bag C - Step 4
91477
M3 Nut
(black)
x2
25202
M3 x 10mm
FHCS
x4
91528
(rear, Inner)
x2
91394
Hinge Pin
91049
Heavy-duty
Ballstud, 10mm
x2
31286
FT Ballstud
Washer,
aluminum
(2mm)
RC10B5M
Rear Ball
Stud Mount
91531
Rear Wing
Mount
x2
89204
M3 x 24mm
BHCS
91518
RC10B5M
Rear Shock
Tower
x2
:: Shock Towers and Rear Chassis Brace Build - Bag C - Step 5
91531
RC10B5M
Rear
Bumper
x2
91518
25203
M3 x 12mm
FHCS
x2
89209
M3 x 18mm
FHCS
x2
Page 8
8
:: Differential Build - Bag D - DD - Step 1
#6591
diff lube
6581
3/32 carbide
x14
diff balls
#6591
diff lube
91419
Diff Gear,
52T
:: Differential Build - Bag D - DD - Step 2
6573
Diff thrust
washer
x2
7666
Diff Drive
Ring
91420
Ball Diff
Outdrive
#6591
diff lube
7666
Diff Drive
Ring
91420
Ball Diff
Outdrive
#6588
black grease
6574
x6
5/64 diff
thrust
balls
6573
Diff thrust
bolt
:: Differential Build - Bag D - DD - Step 3
6575
Locking
t-nut
!
6582
Diff
thrust
spring
Compress
spring first.
31400
x2
5 x 8mm,
Bearing
As you tighten the diff bolt, you will notice the T-nut ears moving
closer to the bottom of the outdrive slot. This compresses the
spring behind the T-nut. The spring should be completely
compressed at the same time the T-nut reaches the end of the
slot. Caution! Pay close attention to the feeling when the spring
is completely compressed. Do not overtighten the bolt. When
you feel the spring completely compressed, loosen the diff bolt
1/8” of a turn. Your diff should now operate smoothly with
resistance as the outdrives move in opposite directions.
After you have driven the car once, re-check the diff setting.
6575
Diff
cover
Page 9
:: Gearbox Build - Bag E - Step 1
25238
6 x 12 x 4,
Bearing
x2
91011
4x4 Idler
Gear Shaft
x2
9
91426
Top Shaft
Spacer
91425
Top Shaft
25616
10 x 15 x 4,
Bearing
x2
91530
RC10B5M
Gearbox
(right & left)
:: Gearbox Build - Bag E - Step 2
Install the Diff with
the head of the
Diff Thrust Bolt
(#6573) facing the
!
opposite side of the
spur gear.
91521
RC10R5M
Chassis
Brace
91429
Idler Gear
31531
M3 x 6mm
BHCS
x2
x2
25237
5 x 10 x 4,
Bearing
x4
:: Slipper Build - Bag F - FF - Step 1
!
There’s also a72T
48P spur gear
(#9649)
included for stock
motor use!
91428
Motor Plate,
blue
89203
M3 x 16mm
BHCS
x5
Slipper Hub
25202
M3 x 10mm
FHCS
7485
FT V2
x3
9603
Slipper
Pad
9651
81T 48P
Spur Gear
91176
VTS Slipper
Housing
91177
VTS Slipper
Pads
91178
VTS Slipper
Plate
91179
VTS Slipper
Hub, outer
x2
Page 10
10
:: Slipper Build - Bag F - FF - Step 2
9739
Slipper
Spring
!
Set nut
flush with
top shaft.
91423
Slipper
Spring
Adapter
:: Slipper Build - Bag F - FF - Step 3
25211
M3 x 10mm
BHCS
x2
91148
M4 Locknut,
with flange
and knurl
89209
M3 x 18mm
FHCS
!
x2
See page 18 for gear
mesh, and slipper clutch
setting instructions!
25202
M3 x 10mm
x4
FHCS
:: Rear Hub and CVA Build - Bag G - Step 1
25616
91047
Heavy-duty
Ballstud, 6mm
91414
Rear Hub
Link Insert
(A)
Build x2 (right and left side)
Rear Hub
10 x 15 x 4
Bearing
91414
91416
Rear Hub
Link Nut
(A)
91414
Rear Hub
Insert
(0°)
91476
6 x 13 x 5
Bearing
!
!
Rear Hub Link Setting:
A
CBBAA
Up
Down
Up
B
Down
There are multiple
optional inserts
for the Rear Hub
Insert (0°, 0.5 °, 1 °).
0° is the standard
insert used.
Page 11
:: Rear Hub and CVA Build - Bag G - Step 2
91438
CVA
Coupler
#6588
black grease
11
91436
CVA Wheel
Hex Pin
91439
CVA Bone
91437
CVA Axle
Build x2 (right and left side) Build x2 (right and left side)
91438
CVA
Pin
91441
Wheel
Hex (rear)
:: Rear Hub and CVA Build - Bag G - Step 3
You can install optional
#4670 set screws to
better hold the rear
hub inserts and
hinge pin.
91394
Hinge Pin
(rear, outer)
91414
Rear Hub
Spacer
x2
31510
M2 x 4mm
BHCS
4670
M3 x 8mm
Set Screw
(not included in kit)
x2
Build x2 (right and left side)Build x2 (right and left side)
:: Turnbuckles Build - Bag H - HH - Step 1
!
Orient the notch
to the left throughout the
car. It indicates which end
has the left hand threads!
Racers Tip:
Use black grease
(#6588) on the
threads of the
turnbuckles for
easier ball cup
installation!
91453
HD Ball Cup
Install the ballstuds on
curved side of the ballcup!
6263
Turnbuckle,
2.06”
HD Ball Cup
Steering Turnbuckle
27.50mm
!
Build x2 (right and left side)
91453
(right)
Page 12
12
:: Turnbuckles Build - Bag H - HH - Step 2
91453
HD Ball Cup
6263
Turnbuckle,
2.06”
91453
HD Ball Cup
Front Camber Turnbuckle
23.85mm
!
Orient the notch
to the left throughout the
car. It indicates which end
has the left hand threads!
:: Turnbuckles Build - Bag H - HH - Step 3
!
Orient the notch
to the left throughout the
car. It indicates which end
has the left hand threads!
Racers Tip:
Use black grease
(#6588) on the
threads of the
turnbuckles for
easier ball cup
installation!
91453
HD Ball Cup
Racers Tip:
Use black grease
(#6588) on the
threads of the
turnbuckles for
easier ball cup
installation!
!
Install the ballstuds on
curved side of the ballcup!
Build x2 (right and left side)
6263
Turnbuckle,
2.06”
91453
HD Ball Cup
Rear Camber Turnbuckle
23.50mm
!
Install the ballstuds on
curved side of the ballcup!
Build x2 (right and left side)
:: Shocks Build - Bag I - II - Step 1
91308
12mm
Shock Piston
(1.6 front)
(1.7 rear)
91488
3 x 21
Shock Shaft
(front)
91489
3 x 27.5
Shock Shaft
(rear)
numbers on the pistons to
make them easily visible!
6299
1/8 E-Clip
Racers Tip:
Use a marker over the
6299
1/8 E-Clip
4187
Nylon Spacer,
(.030)
Front:
2 spacers
Rear:
2 spacers
Page 13
:: Shocks Build - Bag I - II - Step 2
91480
12x23mm V2
Shock Bodies
(front)
91482
12x31mm V2
Shock Bodies
(rear)
5407
O-Ring
91491
V2 Shock
Spacer
91491
V2 Shock
Hat Bushing
x2
x2
91491
12mm
Shock Cap
O-Ring
31327
VCS3 Shock
Bottom Cap
O-Ring
#1105
green slime
31327
VCS3 Shock
Bottom Cap
:: Shocks Build - Bag I - II - Step 3
!
Lightly rub shock oil
on the o-ring before
installation!
Racers Tip:
Coating the o-rings
with green slime
(#1105) helps seal
& reduce o-ring
swell! Green slime
not included in kit!
#1105
green slime
91448
Shock
eyelet
91448
Shock
Pivot Ball
13
Shock oil
#5432
Step 2-3
Shock oil
#5432
Front Shock: 32.5 wt
Rear Shock: 32.5 wt
:: Shocks Build - Bag I - II - Step 4
91304
12mm
threaded
collar
o-ring
x4
Racers Tip:
Use your finger to rub
shock oil on the o-ring for
smoother adjustment!
91328
12mm front
spring, White
(3.30lb)
Shock Bleeding Steps:
1. Before assembly, get each bleed
screw and thread it 1-2 turns into
the shock cap. This will make it easier
when you are bleeding your shocks.
2. Pull shock shaft down.
3. Fill shock body 3/4 full with silicone
shock fluid.
4. Slowly move the shock shaf t up and
down to remove air from under the
piston.
5. Wait for bubbles to come to surface.
6. Fill shock body to top with silicone
shock fluid.
7. Place a drop of oil in the cap and on
cap threads.
8. Install cap (without bleed screw) and
tighten completely.
9. Slowly compress shaf t all the way to
bleed excess silicone shock fluid out
the hole in the cap (use rag aroundshock to catch excess fluid).
10. Install M2x4mm button head screw
until snug while shaft is fully compressed.
Front:
4mm
Rear:
7mm
31510
M2 x 4mm
BHCS
Step 9-10Step 8Step 6-7Step 4-5
91310
12mm shock
spring cup
(5mm offset)
91304
12mm
threaded
collar
x4
91336
12mm rear
spring, Green
(2.00lb)
Build x2 front and x2 rear shocks
Page 14
14
:: Shocks Build - Bag I - II - Step 5
!
Use outside
hole in
front arm!
Bushing
91445
Shock
25612
M3 Locknut,
with flange
(black)
91445
Shock
Bushing
!
Use inside
hole in
rear arm!
25189
M3 x 22mm
BHCS
Build x2 (right and left side) Build x2 (right and left side)
25612
M3 Locknut,
with flange
(black)
89202
M3 x 12mm
BHCS
:: Electronics Build - Bag J - Step 1
91443
Servo
Mount
91455
Servo
Spacers
31286
FT Ballstud
Washer,
aluminum
(1mm)
9180
Servo
Horn
Servo screw
not included!
91047
Heavy-duty
Ballstud, 6mm
91455
Steering
Link
89009
Servo Horn
Ring
Servo not
included!
!
A - Airtronics
F - Futaba
H - Hitec
J - JR
Printed here
Align the servo
horn 90 degrees
31532
M3 x 8mm
BHCS
x4
7337
Gold
Washer
x4
x2
x2
:: Electronics Build - Bag J - Step 2
31532
M3 x 8mm
BHCS
x2
Motor not included!
89218
3 x 8mm
Washer
31532
M3 x 8mm
BHCS
x2
x2
Page 15
:: Electronics Build - Bag J - Step 2
gear mesh setting
!
See page 18 for
instructions!
15
91435
Gear
Cover
91089
Belt Cover
Cap
Pinion / Setscrew
not included!
:: Electronics Build - Bag J - Step 3
ESC not included!
6727
Servo Tape
Receiver not
included!
25225
M3 x 3mm
Set Screw
6338
Antenna
Tube & Cap
!
There are two options
for mounting your
antenna.
31530
M3 x 5mm
BHCS
x2
:: Electronics Build - Bag J - Step 4
4689
M3 x 16mm
Set Screw
91536
RC10B5M
Battery
Spacer
x2
Battery
not included!
91536
RC10B5M
Battery
Spacer
Page 16
16
:: Electronics Build - Bag J - Step 5
91458
x2
Battery Strap
Thumb Wheel
91534
RC10B5M
Battery
Strap
Batteries
not included!
:: Wheels / Tires and Body - Bag K - Step 1
9690
Buggy Front
Wheel Hex,
White
x2
91458
x2
Battery Strap
Thumb Wheel
O-Ring
9695
x2
Buggy Rear
Wheel Hex,
White
Tires / Inserts
not included!
#1597
ca glue
Carefully apply ca glue
(tire adhesive) to the tire
Tires / Inserts
not included!
Build x2 Build x2
bead on both sides. Do
one side at a time, allow it
to dry before gluing the
CA glue not included!
!
other side!
#1597
ca glue
:: Wheels / Tires and Body - Bag K - Step 2
91148
M4 Locknut,
with flange
and knurl
91148
M4 Locknut,
with flange
and knurl
Build 2 (1 left, 1 right) Build 2 (1 left, 1 right)
Page 17
:: Wheels / Tires and Body - Bag K - Step 3
89222
M2.5 x 8mm
SHCS
x2
21173
Small
Body Clips
91531
x2
RC10B5M
Rear
Body Mounts
17
91537
Clear Body,
B5M
:: Wheels / Tires and Body - Bag K - Step 4
21173
Small
Body Clips
x2
Instead of using the included body clips
(#21173), you can use hook and loop tape
on the inside of the body, and the sides of
the chassis to keep your body in place!
Racers Tip:
21173
x2
Small
Body Clips
91471
Clear Wing,
B5
91531
Wing Angle
Shim
:: Wheels / Tires and Body - Bag K - Step 4
Painting Tips:
Your B5M Team Kit comes with a clear polycarbonate body. You will need to prep the body before you
can paint it. Wash the inside thoroughly with warm
water and liquid detergent. Dry the body using a
clean, soft, lint-free cloth. Use the supplied window
masks to cover the windows from the INSIDE of the
body (RC cars get painted from the inside). Using
high quality masking tape, apply tape to the inside of
the body to create a design. Spray (use either rattle
can or airbrush) the paint on the inside of the body
(prefferably dark colors first, lighter colors last).
NOTE: ONLY use paint that is recommended for use
with (polycarbonate) plastics. If you do not, you can
destroy the plastic body!!!!.
After paint has completely dried, cut the body along
the trim lines. Make sure to drill or use a body reamer
to make the holes for the body mounts and antenna!
Page 18
18
:: Tuning Tips
Tips for Beginners:
Before making any changes to the standard setup, make sure you can get around the track without crashing.
Changes to your vehicle will not be beneficial if you can’t stay on the track. Your goal is consistent laps.
Once you can get around the track consistently, start tuning your vehicle. Make only ONE adjustment at a time, testing
it before making another change. If the result of your adjustment is a faster lap, mark the change on the included setup
sheet (make adddtional copies of the sheet before writing on it). If your adjustment results in a slower lap, revert back
to the previous setup and try another change.
When you are satisfied with your vehicle, fill in the setup sheet thoroughly and file it away. Use this as a guide for future
track days or conditions. Peridicaly check all moving suspension parts. Suspension components must be kept clean
and move freely without binding to prevent poor and/or inconsistent handling.
Motor Gearing:
Proper motor gearing will result in maximum performance and run time while reducing the chance of overheating and
premature motor failure. The gear ratio chart lists recommended starting gear ratios for the most widely used
motor types. Gear ratios will vary depending upon motor brand, wind, and electronic speed control. Consult your
motor and electronic speed control manufacturers for more information.
Team Associated is not responsible for motor damage due to improper gearing.
B5M Gear Ratio Chart (Internal Gear Ratio 2.60:1)
Motor
Pinion
Spur
Final Drive Ratio
17.5 Reedy Sonic Brushless *
17.5 Reedy Sonic Brushless
13.5 Reedy Sonic Brushless *
13.5 Reedy Sonic Brushless
10.5 Reedy Sonic Brushless
9.5 Reedy Sonic Brushless
8.5 Reedy Sonic Brushless
7.5 Reedy Sonic Brushless
6.5 Reedy Sonic Brushless
3300kV Brushless
3900kV Brushless
4900kV Brushless
6100kV Brushless
* These gearings are for use with advanced timing speed control settings!
23
31
22
30
24
23
22
21
21
21
21
19
18
78
69
81
75
81
81
81
81
81
81
81
81
81
8.82:1
5.79:1
9.57:1
6.50:1
8.78:1
9.15:1
9.57:1
10.03:1
10.03:1
10.03:1
10.03:1
11.08:1
11.70:1
Set The Gear Mesh:
You should be able to rock the spur gear back and forth in the teeth of the pinion gear without making the pinion gear
move. If the spur gear mesh is tight, then loosen the #31532 screws and move the motor away, then try again.
A gear mesh that is too tight or too loose will reduce power and damage the gear teeth.
Slipper Clutch:
The assembly instructions give you a base setting for your clutch. Turn the nut on the shaft so that the end of the top
shaft is even with the outside of the nut. At the track, tighten or loosen the nut in 1/8 turn increments until you hear
a faint slipping sound for 1-2 feet on takeoffs. Another popular way to set the clutch is to hold both rear tires firmly in
place and apply short bursts of throttle. If the clutch is properly set, the front tires should lift slightly up off the surface.
Ride Height:
Ride height is the distance from the ground to the bottom of the chassis.
The standard front ride height setting is with the front arms level
(reffered to as “arms level”) or 24mm (Ride Height Gauge #1449).
Check the ride height by lifting up the entire car about 8-12 inches off the
bench and drop it. After the suspension “settles” into place, measure
ride height (Ride Height Gauge #1449). Raise or lower the shock collars
as necessary so that the left & right arms appear to be level.
*Front arms inner
and outer hinge pins
imaginary horizontal
line when ride height
!
should be in a
is set
The rear ride height setting you should use most often is with the
outdrive, driveshaft, and axles all on the same imaginary horizontal line
(reffered to as “bones level”) or 24mm (Ride Height Gauge#1449).
Check the ride height by lifting up the entire car about 8-12 inches off the
bench and drop it. After the suspension “settles” into place, measure
ride height (Ride Height Gauge #1449). Raise or lower the shock collars
as necessary so that the left & right driveshafts appear to be level.
!
*CVA bones should
be in a straight line
when ride height is
set at “CVA bones
level”
Page 19
:: Tuning Tips (cont.)
Wheelbase Adjustment:
You have three options for rear hub spacing, Forward, Middle, & Back.
The kit setting of Middle is the most neutral, and will be used most often.
For improved handling in bumps or rhythm sections, try moving the hubs to the
Back position. This can also make the car handle better in 180° turns.
*Spacers to the rear
will place hubs for-
ward, shortening
the wheelbase
!
Front Camber:
Camber describes the angle at which the tire and wheel rides when
looked at from the front. Negative camber means that the tire leans
inward at the top. A good starting camber setting is -1°. Positive camber,
where the top of the tire is leaning out, is not recommended.
Optional #1719 camber gauge can be used to more accurately set camber.
*Testing camber
with camber gauge
!
Rear Camber:
Camber describes the angle at which the tire and wheel rides when looked at from the back. Negative camber means
that the tire leans inward at the top. A good starting camber setting is -1°. Adding a small amount of positive camber,
where the top of the tire is leaning out, will tend to improve straight-line acceleration on loose tracks.
Optional #1719 camber gauge can be used to more accurately set camber.
Front Camber Links:
Changing the length of the camber link is considered a bigger step than
adjusting the ball end height on the tower. Shortening the camber link
(or lowering the ball end) will give the front end less roll and quicken steering
response. Lengthening the camber link (or raising the ball end) will give the
front more roll and slower steering response. Longer camber links are
typically used on high grip tracks and shorter links tend to work better on
medium-grip loose tracks.
*Raise or lower the
ball end by adding
!
or subtracting
washers here
19
Rear Camber Link:
Changing the length of the camber link is considered a bigger step than adjusting
the ball end height on the rear chassis brace. Shortening the camber link
(or lowering the ball end) will give the rear end less roll and the car will tend to
accelerate or “square up” better. Lengthening the camber link (or raising the ball
end) will give the rear more roll and more cornering grip. Longer camber links are
typically used on high grip tracks, while shorter links tend to work better on
medium grip loose tracks. The kit setting is the best compromise of cornering grip
and acceleration.
*Raise or lower
!
the ball end by
adding or
subtracting
washers here
Kickup:
Kickup is the angle the front suspension arm mounts at where the front of the arm is higher than the rear.
The standard kickup angle for the B5 is 25°, and is most common. If more corner entry steering is desired, try the
included 30° front bulkhead. It is important to adjust the bumpsteer to match the kickup angle adjustment.
Refer to the chart below for some common settings:
Kickup
Angle
25° 1mm 0mm
Less Agressive
Bumpsteer Shims
Standard
Bumpsteer Shims
More Agressive
Bumpsteer Shims
N/A
30° 3mm 2mm 1mm
Caster:
Caster describes the angle of the kingpin as it leans toward the rear of the vehicle. Positive caster means the kingpin
leans rearward at the top. The B5 includes two inserts to adjust caster angle at the caster block, 0° and +5°. The total
caster angle is the sum of the kick-up angle and the caster block angle. Standard total caster angle for the B5 is 30°,
with 25° kick-up and 5° caster block angle. For less entry steering and more exit steering, try 0° caster block angle.
Page 20
20
:: Tuning Tips
Trailing Axle:
Trailing axle is the distance from the king pin to the axle that “trails” behind the pin. The B5 includes inserts to allow
adjustments for trailing axle to three positions: 4mm (standard), 3mm, and 2mm. The standard setup uses 4mm
trailing axle for the most stable handling. For more corner entry steering, try the 3mm trailing axle option.
It is important to adjust the ackermann and wheelbase settings to match the trailing axle adjustment. refer to the
chart below for some common settings:
Trailing Axle
Position
4mm
3mm
2mm
# of Shims
on Rack for
Less Ackermann
3mm
2mm
1mm
# of Shims
on Rack for
Std. Ackermann
2mm
1mm
0mm
# of Shims
on Rack for
More Ackermann
1mm 2mm (forward)
0mm 1mm (middle)
N/A 0mm (back)
Rear Caster Block
Wheelbase Shim
Ackermann:
Ackermann is the angle difference between the front wheels when they are turned to steer the car. For minimal tire
slip, it is standard for the inside wheel to steer to a greater angle than the outside wheel. The B5 allows ackermann
adjustments by changing the washer thickness used behind the steering rack ballstuds. The kit setup uses 2mm washers and is most common for racing conditions. If corner entry steering is too aggressive, try increasing the ackermann
by removing shims from behind the steering rack ballstuds. Increasing the ackermann will increase the angle dif ference
of the front wheels when steered, resulting in a more stable car on corner entry.
Anti-Roll Bars:
The optional #91468 rear anti-roll bar kit (also called the “swaybar”) allows you to add roll resistance to the rear end
with minimal effect on handling over bumps and jumps. It is an especially helpful tuning item on high-grip tracks
(try the gold bar). The silver and black anti-roll bars are typically used on medium-grip loose tracks.
Page 21
21
:: Shocks
4187
.030 Nylon Washer
5407
Red O-Rings
6299
31327
31510
91304
91308
91310
91448
91449
91480
91482
91488
91489
91491
91496
91498
E-Clip
VCS3 Shock Bottom Cap and O-Ring
M2 x 4mm BHCS
12MM Threaded Collar and O-Ring
12MM Shock Pistons, (1.5, 1.6, 1.7)
12MM Shock Spring Cups (+0mm, +5mm, +9mm)
Shock Pivot Ball and Rod End
12MM V2 Composite Shock Cap
w/O-ring and bleeder screw
12x23MM V2 Shock Bodies
12x31MM V2 Shock Bodies
3x21MM Shock Shaft
3x27.5MM Shock Shaft
12MM V2 Shock Rebuild Kit
12x23B/21S V2 Shock Kit (B5 Front)
12x31B/27.5S V2 Shock Kit (B5 Rear)
91449
91491
31510
6299
91308
91304
12
8
12
2 ea.
6
2
4 ea.
4 ea.
4
4
2
2
1
1
1
2
2
:: Ball Differential
6573
6574
6575
6581
6582
7666
7677
31400
91419
91420
91421
Diff Thrust Washer & Bolt
Precision Diff Thrust Balls, 5/64”
Locking T-Nut, Diff Thrust Bolt, & Cover
3/32” Carbide Diff Balls
Diff Thrust Spring
Diff Drive Rings, 2.60:1
Ball Diff Rebuild Kit
Bearing, 5 x 8mm
Diff Gear, B5
Ball Diff Outdrive, B5
Ball Diff Kit, B5
6575
6582
91420
2
6
1
12
1
2
1
2
1
1 ea.
1
91421
31400
7666
91420
91480
91482
5407
91491
5407
31327
31327
:: Shock Springs
91325
91326
91327
91328
91329
91330
91331
91332
91333
91334
91335
91336
91337
91338
91339
91340
91341
91342
91343
91344
91345
12MM Front SPRING BRN 2.85
12MM Front SPRING BLK 3.00
12MM Front SPRING GRN 3.15
12MM Front SPRING WHT 3.30 - Kit
12MM Front SPRING GRY 3.45
12MM Front SPRING BLU 3.60
12MM Front SPRING YLW 3.75
12MM Front SPRING RED 3.90
12MM Front SPRING ORN 4.05
12MM Front SPRING PRL 4.20
12MM Rear SPRING BLK 1.90
12MM Rear SPRING GRN 2.00 - Kit
12MM Rear SPRING WHT 2.10
12MM Rear SPRING GRY 2.20
12MM Rear SPRING BLU 2.30
12MM Rear SPRING YLW 2.40
12mm Big Bore Front Soft Spring Kit
12mm Big Bore Front Medium Spring Kit
12mm Big Bore Front Hard Spring Kit
12mm Big Bore Rear Soft Spring Kit
12mm Big Bore Rear Medium Spring Kit
6299
91488
91489
4187
91304
91310
91448
91448
Pr.
Pr.
Pr.
Pr.
Pr.
Pr.
Pr.
Pr.
Pr.
Pr.
Pr.
Pr.
Pr.
Pr.
Pr.
Pr.
1
1
1
1
1
:: Shock Oil
5420
5421
5422
5423
5424
5425
5426
5427
5428
5429
5430
5431
5432
5433
5434
5435
5436
5437
5438
10 Weight Silicone Shock Oil
20 Weight Silicone Shock Oil
30 Weight Silicone Shock Oil
40 Weight Silicone Shock Oil
22.5 Weight Silicone Shock Oil
80 Weight Silicone Shock Oil
27.5 Weight Silicone Shock Oil
15 Weight Silicone Shock Oil
25 Weight Silicone Shock Oil
35 Weight Silicone Shock Oil
45 Weight Silicone Shock Oil
55 Weight Silicone Shock Oil
32.5 Weight Silicone Shock Oil
37.5 Weight Silicone Shock Oil
42.5 Weight Silicone Shock Oil
50 Weight Silicone Shock Oil
60 Weight Silicone Shock Oil
70 Weight Silicone Shock Oil
47.5 Weight Silicone Shock Oil
31400
7666
6573
6574
6573
6581
6575
91419
6575
2oz.
2oz.
2oz.
2oz.
2oz.
2oz.
2oz.
2oz.
2oz.
2oz.
2oz.
2oz.
2oz.
2oz.
2oz.
2oz.
2oz.
2oz.
2oz.
Page 22
22
:: Transmission
25202
25211
25237
25238
25616
31531
31532
89203
89218
91011
91425
91426
91428
91429
91521
91530
M3 x 10mm FHCS
M3 x 10mm BHCS
Bearing, 5 x 10 x 4
Bearing, 6 x 12 x 4
Bearing, 10 x 15 x 4
M3 x 6mm BHCS
M3 x 8mm BHCS
M3 x 16mm BHC
3 x 8mm Washer
4x4 Idler Gear Shaft
Top Shaft, B5
Top Shaft Spacer, B5
Motor Plate (Blue), B5
Idler Gears, B5
RC10B5M Chassis Brace
RC10B5M Gearbox
(Right & Left)
20
20
2
2
2
6
6
10
10
1
1
1
1
2
1
1 ea.
89203
91530
91521
25616
31531
25211
25238
91429
91425
25237
91426
91011
25238
91429
25237
91011
25237
25211
91428
:: Slipper Clutch
7485
9603
9648
9649
9650
9651
9652
9653
9739
31530
91089
91148
91175
91176
91177
91178
91179
91423
91435
FT V2 Slipper Hubs
Slipper Pad
69T 48P Spur Gear
72T 48P Spur Gear (Kit)
75T 48P Spur Gear
81T 48P Spur Gear (Kit)
78T 48P Spur Gear
84T 48P Spur Gear
Slipper Spring
M3 x 5 BHCS
4X4 Belt Cover Cap
M4 Locknut, w/flange and knurl
FT VTS Slipper Conversion
VTS Slipper Housing
VTS Slipper Pads
VTS Slipper Plate
FT VTS Slipper Hub, outer
Slipper Spring Adapter
Gear Cover (Black), B5
25616
91530
89218
2
2
1
1
1
1
7485
1
1
1
6
2
4
1
1
2
1
1
2
1
9649
9651
9603
91176
91178
91179
91423
91177
91177
9739
91148
31530
25202
25202
31532
31532
91435
31530
91089
:: Pinion Gears
8253
8254
8255
8256
8257
8258
8259
8260
8261
8263
8264
8265
8266
16T 48P Pinion Gear
17T 48P Pinion Gear
18T 48P Pinion Gear
19T 48P Pinion Gear
20T 48P Pinion Gear
21T 48P Pinion Gear
22T 48P Pinion Gear
23T 48P Pinion Gear
24T 48P Pinion Gear
26T 48P Pinion Gear
27T 48P Pinion Gear
28T 48P Pinion Gear
29T 48P Pinion Gear
8267
1
8268
1
8269
1
8270
1
8271
1
8272
1
1
1
1
1
1
1
1
30T 48P Pinion Gear
31T 48P Pinion Gear
32T 48P Pinion Gear
33T 48P Pinion Gear
34T 48P Pinion Gear
35T 48P Pinion Gear
1
1
1
1
1
1
Page 23
:: Optional Gear Differential
4675
91461
91462
91463
91465
M2.5 x 6 FHCS
Gear Diff Kit, B5
Gear Diff Gear/Cover, B5
Gear Diff Rebuild, B5
Gear Diff Outdrives, B5
6
1
1
1
2
91465
91465
91465
91465
4675
91465
4675
23
91462
91463
:: Differential Fluids
5450
5451
5452
5453
5454
5455
5456
5457
5458
5459
Silicone Diff Fluid 1,000CST
Silicone Diff Fluid 2,000CST
Silicone Diff Fluid 3,000CST
Silicone Diff Fluid 5,000CST
Silicone Diff Fluid 7,000CST
Silicone Diff Fluid 10,000CST
Silicone Diff Fluid 20,000CST
Silicone Diff Fluid 30,000CST
Silicone Diff Fluid 60,000CST
Silicone Diff Fluid 100,000CST
1
1
1
1
1
1
1
1
1
1
:: Turnbuckles and Servo Mounts
6263
7337
9180
31286
31532
89007
91047
91443
91453
91455
Turnbuckle, 2.06”
.250 x .125 x .015” Washer
Servo Horns, Molded
FT Ballstud Washer, aluminum
(1mm, 2mm)
M3 x 8 BHCS
Steering Servo Ring, blue
Heavy-duty Ballstud, 6mm
Servo Mount, B5
HD Ball Cup Set (Small), B5
Steering Link, B5
6263
91453
91453
2
4
1
4 ea.
6
1
8
2
1
4
31286
91047
9180
7337
31532
31532
89007
91455
7337
91455
7337
31532
31532
91465
31532
91443
7337
91462
91465
91465
91465
31532
91443
91455
:: Front Bulkhead / Steering
5407
21173
25189
25202
31286
89202
91047
91048
91362
91391
91475
Red O-Ring
Small Body Clips
M3 x 22mm BHCS
M3 x 10mm FHCS
FT Ballstud Washer, aluminum
(1mm, 2mm)
M3 x 12mm BHCS
Heavy-duty Ballstud, 6mm
Heavy-duty Ballstud, 8mm
Top Plate, B5
Steering Set, B5
3x7x3 Ball Bearing
8
12
20
20
4 ea.
10
8
8
1
1
8
21173
5407
25202
31286
91048
91362
5407
25202
91475
31286
91048
91391
89202
91475
91475
91475
91391
91475
25189
91047
91391
91475
91391
Page 24
24
Steering Block, Hex
:: Front Arm
4670
25189
25237
31510
31520
31530
31550
89202
91047
91049
91148
91394
91400
91402
91404
91406
91407
91526
M3 x 8mm Set Screw
M3 x 22mm BHCS
Bearing, 5 x 10 x 4
M2 x 4mm BHCS
M2.5 x 6mm BHC
M3 x 5mm BHCS
FT M3 Locknut, blue aluminum
M3 x 12mm BHCS
Heavy-duty Ballstud, 6mm
Heavy-duty Ballstud, 10mm
M4 Locknut, with flange and knurl
Hinge Pin Set, B5
Caster Block, B5
Caster Block Bushing, B5
Steering Block, B5
Front Axles, B5
Front Axle Crush Tubes, B5
RC10B5M Front Arms
6
20
2
6
6
6
6
10
8
8
8
1
Pr.
4
Pr.
2
2
Pr.
91049
91400
4670
91400
89202
89202
31530
91402
31550
31520
91404
91404
25237
91047
91407
25237
:: Rear Arm
4670
25616
31510
89202
91047
91148
91394
91414
91416
91436
91437
91438
91439
91441
91476
91528
M3 x 8mm Set Screw
Bearing, 10 x 15 x 4
M2 x 4mm BHCS
M3 x 12mm BHCS
Heavy-duty Ballstud, 6mm
M4 Locknut, with flange and knurl
Hinge Pin Set, B5
Rear Hubs, B5
Rear Hub Link Nut Set, B5
CVA/Wheel Hex Pin, B5
CVA Axle, B5
CVA Rebuild Kit, B5
CVA Bone, B5
Wheel Hex (Rear), B5
6x13x5 Ball Bearing
RC10B5M Rear Arms
10
Pr.
Pr.
31550
31510
91394
25189
91526
91400
6
2
6
8
8
1
1
4
2
1
1
2
2
91439
91438
91438
91437
25616
91416
91414
91404
91406
91148
31510
91394
91414
91047
91414
91476
91528
31510
91394
91414
91414
89202
91441
4670
91436
91148
Page 25
:: Battery Strap
4689
91458
91534
91536
M3 x 16mm Set Screw
Battery Strap Thumbwheel, B5
RC10B5M Battery Strap
RC10B5M Battery Foams
25
6
2
1
1
91458
91458
4689
91458
91458
4689
:: Front Shock Tower
25612
31286
89202
89204
91049
91445
91477
91516
M3 Locknut, with flange
FT Ballstud Washer, aluminum
(1mm, 2mm)
M3 x 12mm BHCS
M3 x 24mm BHCS
Heavy-duty Ballstud, 10mm
Shock Bushing (Composite), B5
M3 Nut, Black
RC10B5M Front Shock Tower
20
4 ea.
10
10
8
4
6
1
91536
91536
89204
89204
31286
91477
91534
91536
91049
91445
91536
91049
31286
25612
25612
:: Rear Shock Tower
21173
25202
25203
25612
31286
89204
91445
91477
91518
91531
Small Body Clips
M3 x 10mm FHCS
M3 x 12mm FHCS
M3 Locknut, with flange
FT Ballstud Washer, aluminum
(1mm, 2mm)
M3 x 24mm BHCS
Shock Bushing Composite, B5
M3 Nut, Black
RC10B5M Rear Shock Tower/Mount
RC10B5M Wing Mounts and Shim
12
20
20
20
4 ea.
10
4
6
1
1
89202
25612
91049
31286
89202
91445
91518
25202
91477
91445
25612
89204
91477
91516
21173
91531
91518
91445
91477
21173
91531
91531
25203
89204
Page 26
26
:: Chassis
6338
21173
25201
25202
25225
31521
31550
89209
89222
91364
91371
91394
91410
91510
91512
91514
91531
91532
Antenna Tube & Cap (black)
Small Body Clips
M3 x 8mm FHCS
M3 x 10mm FHCS
M3 x 3mm Set Screw
M2.5 x 8mm BHCS
FT M3 Locknut, Blue Aluminum
M3 x 18mm FHCS
M2.5 x 8mm SHCS
Bulkhead (25° & 30°), B5
Hinge Pin Brace, B5
Hinge Pin Set, B5
Front Bumper, B5
RC10B5M Chassis
RC10B5M Front Chassis Plate
RC10B5M Chassis Cradle
RC10B5M Wing Mount/Rear Bumper
RC10B5M Composite Arm Mount Set
1
12
20
20
20
6
6
10
10
1
1
1
1
1
1
1
1
1
31521
91364
91371
25202
25225
6338
6338
89222
91531
25202
21173
89222
91531
21173
91514
25201
31550
91532
25202
:: Wheels
9690
9691
9695
9696
Buggy Front Wheel, hex, white
Buggy Front Wheel, hex, yellow
Buggy Rear Wheel Hex, white
Buggy Rear Wheel Hex, yellow
91394
25202
91394
31550
91532
91531
89209
91512
91510
2520425204
91410
25204
25204
2
2
2
2
9691
25201
25202
25201
25202
25202
9696
89209
25201
25202
89209
25201
25202
25201
Not included
in Kit!
Not included
in Kit!
Page 27
27
:: Factory Team and Option Parts
1406
1409
1734
1735
1736
7485
7486
7495
31286
91175
91176
91177
91178
91179
91363
91372
91374
91376
91378
91381
91382
91385
91389
91392
91395
91399
91401
91403
91405
91408
91409
91413
91415
91442
91446
91447
91450
91457
91468
91492
91493
91495
91513
91515
91517
91519
91520
91522
91523
91524
91525
91527
91529
91533
91535
FT Ti Turnbuckle, 2.00” (blue)
FT Ti Turnbuckle, 1” (sway bar) (blue)
FT Blue Body Clip, 4 long, 6 short
FT Blue Body Clip, long
FT Blue Body Clip, short
FT V2 Slipper Hubs
FT V2 Slipper Spring and Washer
Vented V2 Slipper Hubs
FT Ballstud Washer, aluminum (1mm, 2mm)
FT VTS Slipper Conversion
VTS Slipper Housing
VTS Slipper Pads
VTS Slipper Plate
FT VTS Slipper Hub, outer
Top Plate (HARD), B5
Aluminum Front Pin Brace, B5
Front Tower (HARD), B5
Rear Tower (HARD), B5
Chassis Brace (HARD), B5
ESC Mount, B5
Arm Mount Set, B5
Arm Mount Inserts Set (C), B5
Arm Mount Insert (D), B5
Aluminum Steering Set, B5
TiN Hinge Pin Set, B5
Front Arms (HARD), B5
Caster Block (HARD), B5 w/inserts
Caster Block Bushing (Offset - long/short), B5
Steering Block (HARD), B5
Front Axle (Clamp Hex), B5 - Req. #91409
Clamping Hex (Front), B5 - Req. #91408
Rear Arms (HARD), B5
Rear Hubs (HARD), B5 w/inserts
Clamping Hex (Rear), B5
Shock Bushing (Aluminum), B5 - Req. #91447
Shock Bushing Ball, B5 - Req. #91446
12mm V2 Aluminum Shock Cap
(2 screws, 2 bleeder gaskets, and 2 o-rings)
Graphite Battery Strap, B5
Anti-Roll Bar Kit, B5
12mm V2 Bleeder Gasket/Screw
FT Low Friction X-Rings
12mm V2 X-Ring Rebuild Kit
(4 clear x rings, 2 spacers, 4 hat bushings)
RC10B5M Front Chassis Plate (HARD)
RC10B5M Chassis Cradle (HARD)
RC10B5M Front Tower (HARD)
RC10B5M Rear Tower/Mount (HARD)
RC10B5M Rear Ball Stud Mount, Aluminum
RC10B5M Aluminum Arm Mount C
RC10B5M Brass Arm Mount (C)
RC10B5M ALuminum Arm Mount D
RC10B5M Brass Arm Mount (D)
RC10B5M Front Arm (HARD)
RC10B5M Rear Arm (HARD)
RC10B5M Shock Bushing, Short
RC10B5M Anti-Roll Bar Kit
:: Body and Decals
91538
91471
91537
RC10B5M Clear Body
RC10B5 Clear Wing
RC10B5M Sticker Sheet
Pr.
Pr.
10
4
6
Pr.
1
2
4ea.
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
Pr.
Pr.
2ea.
Pr.
2
2
Pr.
Pr.
2
4
4
2
1
1
1
8
1
1
1
1
1
1
1
1
1
1
Pr.
Pr.
4
1
1
1
1
:: XP Electronics
29107
29133
29134
29138
29139
29140
29141
29142
29143
29144
29145
29146
29166
29167
29168
29209
29210
29211
29212
29214
29215
29216
29250
29251
29252
29253
29254
XP DS1903/S1903 Metal Gear Set
XP DS1903 Digital Servo
XP DS1903MG Digital Servo
XP SC500-BL Brushless ESC
XP SC900-BL Brushless ESC
XP SC200 Brushed ESC
XP SC450 Brushless ESC
XP ESC Fan Option
XP SC700-BL Brushless ESC
XP SC1200-BL Brushless ESC
XP SC1300-BL Brushless ESC
XP SC1300DB Brushless ESC
XP DS1313 Digital Servo
XP DS1015 Digital Servo
XP DS1510MG Digital Servo
Gear Set, DS1313
Gear Set, DS1015
Servo Case , DS1313/DS1015
Accessory Pack, DS1313/DS1015
TRS403-SSi 2.4GHz 4Ch Receiver
XP2G 2.4GHz Radio System
XP3G 2.4GHz Radio System
XP DS1505 Digital Servo
XP DS1505MG Digital Servo
XP DS1505 Metal Gear Set
XP DS1510 Metal Gear Set
XPSSi Receiver Antenna
:: Reedy Accessories
247
248
249
250
604
606
607
609
610
643
644
645
646
647
648
650
654
655
656
658
659
660
661
663
664
669
716
961
962
974
975
978
979
980
981
982
992
Sonic 540 Mach 2 Sensor w/bearing
Sonic 540 Mach 2 Steel Bearing Set
Sonic 540 Mach 2 Ceramic Bearing Set
Sonic 540 Mach 2 Insulator Set
526-S AC/DC 2S-6S LiPo/LiFe Charger
Charge Harness 2S Saddle Pack 4mm
Charge Harness 2S Standard Pack 4mm
TAM to DEANS® charge adapter
447-S AC/DC NiMH Peak Charger
Low-Profile Bullet Connector, 4mm x 14mm (2)
Low-Profile Bullet Connector, 4mm x 14mm (10)
Low-Profile Bullet Connector, 5mm x 14mm (2)
Low-Profile Bullet Connector, 5mm x 14mm (10)
Pro Silicone Wire, 12AWG Black
Pro Silicone Wire, 14AWG Black
Shrink Tubing (Yellow, Orange, Red, Blue, Black)
4.0mm Bullet Plugs (2M, 2F)
4.0mm Bullet Plugs (2M, 10F)
4.0mm Bullet Plugs (10F)
4.0mm Bullet Plugs (10M)
4.0mm Bullet Plugs (30M)
3.5mm Bullet Plugs (3M, 3F)
3.5mm Bullet Plugs (10F)
3.5mm Bullet Plugs (10M)
3.5mm Bullet Plugs (30M)
5mm Bullet Connector
Reedy 09 Decal Set
Sonic 540/550 Timing Cap with Screws
Sonic 540 Case Screws
540-SL/550-SL Steel Bearing Set
540-SL/550-SL Ceramic Bearing Set
Flat Sensor Wire 70mm
Flat Sensor Wire 110mm
Flat Sensor Wire 150mm
Flat Sensor Wire 200mm
Flat Sensor Wire 270mm
Sonic 540 Rotor Spacers
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3ea.
1
1
1
1
1
1
1
1
1
2
1
1
3
1
1
1
1
1
1
1
1
Page 28
28
:: Reedy Batteries
302
310
314
602
632
637
737
738
AA Alkaline 1.5V (4)
LiPo 65C 5700mAh 7.4V SP
LiPo 65C 6000mAh 7.4V SQ
LiPo 65C 4100mAh 7.4V Shorty
LiPo TX Lightweight Battery 1350mAh 11.1V
LiPo TX Battery - M11X 2500mAh 7.4V
Wolfpack LiPo 4800mAh 7.4V 25C S.P.
Wolfpack LiPo 3800mAh 7.4V 25C Shorty
:: Reedy Motors and ESC’s
228
231
232
233
233S
234
235
236
237
238
239
240
241
242
243
244
245
246
908
920
921
922
923
941S
954
955
956
957
958
965
966
967
983
984
985
986
987
Sonic 540 Mach 2 25.5 Competition Brushless Motor
Sonic 540 Mach 2 21.5 Competition Brushless Motor
Sonic 540 Mach 2 17.5 Competition Brushless Motor
Sonic 540 Mach 2 13.5 Competition Brushless Motor
Sonic 540/540 Mach 2 Stator 13.5
Sonic 540 Mach 2 10.5 Competition Brushless Motor
Sonic 540 Mach 2 9.5 Competition Brushless Motor
Sonic 540 Mach 2 8.5 Competition Brushless Motor
Sonic 540 Mach 2 8.0 Competition Brushless Motor
Sonic 540 Mach 2 7.5 Competition Brushless Motor
Sonic 540 Mach 2 7.0 Competition Brushless Motor
Sonic 540 Mach 2 6.5 Competition Brushless Motor
Sonic 540 Mach 2 6.0 Competition Brushless Motor
Sonic 540 Mach 2 5.5 Competition Brushless Motor
Sonic 540 Mach 2 5.0 Competition Brushless Motor
Sonic 540 Mach 2 4.5 Competition Brushless Motor
Sonic 540 Mach 2 4.0 Competition Brushless Motor
Sonic 540 Mach 2 3.5 Competition Brushless Motor
Replacement Rotor 540-SL
540-SL Brushless Motor 3300kV
540-SL Brushless Motor 3900kV
540-SL Brushless Motor 4900kV
540-SL Brushless Motor 6100kV
Sonic 540/540 Mach 2 Stator 17.5
Sonic 540 Stock Rotor 12.3 x 24.2 (7.25)
Sonic 540 Stock Rotor 12.3 x 25.0 (7.25)
Sonic 540 Stock Rotor 12.5 x 25.0 (7.25)
Sonic 540 Modified Rotor 12.2 x 25.0 (5.0)
Sonic 540 Modified Rotor 12.5 x 25.0 (5.0)
Reedy 540-SL 3300kV/XP SC700-BL ESC Combo
Reedy 540-SL 3900kV/XP SC700-BL ESC Combo
Reedy 540-SL 4900kV/XP SC700-BL ESC Combo
Reedy 540-SL 3300kV/XP SC1200-BL ESC Combo
Reedy 540-SL 3900kV/XP SC1200-BL ESC Combo
Reedy 540-SL 4900kV/XP SC1200-BL ESC Combo
Reedy 540-SL 6100kV/XP SC1200-BL ESC Combo
Sonic 540 Modified Rotor 13.0 x 25.0 (5.0)
:: Lubes & Adhesives / Decals / Misc.
1105
1596
1597
6588
6591
6636
6727
716
3816
3820
3834
9787
FT Green Slime Shock Lube
FT Locking Adhesive
FT Tire Adhesive, medium
Black Grease - 4cc
S.Diff Lube - 4cc
Silicone Grease - 4cc
Servo Tape
Reedy 2009 Sticker Set
American Bumper Sticker
AE Logo Decal Sheet
AE Blue Embossed Logo Sticker
FT Chassis Protective Sheet
1
1
1
1
1
1
2
1
1
1
2
1
:: Qualifier Series Vehicles
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
7052
20111
20119
20510
30112
:: 1/18 Kits and RTR’s
20103
20121
:: 1/12, 1/10 Kits and RTR’s
4020
7025
7028C
7030
7030C
7038
7039
7046
7049
7050
7051
7054
7055
7093
8020
8022
9040
9041
9042
9050
9062
30101
30109
90001
90003
90005
90006
90008
90010
Pro Lite 4x4 RTR, 1/10 Scale (ready-to-run)
Rival Mini Monster Truck 1/18 Scale (ready-to-run)
APEX Mini Touring RTR
RIVAL Electric Monster Truck RTR, 1/8 Scale
(ready-to-run)
APEX Touring V-Type, 1/10 Scale (ready-to-run)
RC18B2 - RC18T2 Team Kit
SC18 RTR Brushless (ready-to-run)
RC12R5.2 Factory Team Kit
RC10T4.2 Factory Team Kit
SC10 Pro Comp RTR (ready-to-run) Combo
SC10 KMC Wheels Race Truck RTR (ready-to-run)
SC10 KMC Wheels RTR (ready-to-run) Combo
SC10.2 Factory Team Kit
RC10T4.2 RS RTR 2.4GHz Brushless (ready-to-run)
SC10 RS RTR, Lucas Oil (ready-to-run)
SC10 RS RTR, Rockstar/Makita (ready-to-run)
SC10 RS RTR, Hart and Huntington (ready-to-run)
SC10 RS RTR, Lucas Slick Mist® Body
SC10 RS RTR, Toyota Racing/TRD
SC10 RS RTR, Monster Energy Toyota
SC10GT RTR (ready-to-run)
RC10R5 Factory Team Kit
RC10R5.1 Factory Team Kit
RC10B4.1 Worlds Kit
RC10B4.2 Factory Team Kit
RC10B4.2 RS RTR 2.4GHz Brushless (ready-to-run)
SC10B RS RTR (ready-to-run)
RC10B44.2 Factory Team 4WD Buggy Kit
TC4 Club Racer 4WD Touring Car Race Roller
RC10TC6.2 Factory Team 4WD Touring Car Kit
RC10B5 Team Kit
RC10B5M Team Kit
SC10 4x4 Lucas Oil RTR (ready-to-run)
SC10 4x4 Pro Comp RTR (ready-to-run)
Limited Edition SC10 4x4 RTR Monster Energy
SC10 4x4 Factory Team Kit
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Page 29
29
:: 1/8 Kits and RTR’s
20501
20502
20503
20504
80906
80907
80908
80909
80912
80933
80934
MGT 4.60 SE RTR (ready-to-run)
MGT 8.0 Nitro RTR (ready-to-run)
Limited Edition MGT 4.60 Nitro RTR, w/flag body
(ready-to-run)
Limited Edition MGT 8.0 Nitro RTR, w/flag body
(ready-to-run)
RC8.2 Nitro Buggy Factory Team Kit
RC8.2e Electric Buggy Factory Team Kit
RC8.2e Electric Buggy RTR (ready-to-run)
RC8.2RS Nitro Buggy RTR (ready-to-run)
RC8T Championship Edition
SC8.2e Short Course Race Truck, Rockstar/Makita
Electric RTR (ready-to-run)
SC8.2e Short Course Race Truck, Slick Mist Electric
RTR (ready-to-run)
:: Tools
1111
1113
1449
1541
1542
1543
1544
1545
1546
1547
1548
1553
1554
1561
1562
1563
1564
1565
1567
1589
1590
1592
1655
1656
1657
1658
1659
1660
1661
1662
1663
1664
1665
1666
1667
1668
1669
1670
1671
1672
1673
1674
1719
1737
3718
3719
3720
3987
6429
6956
7494
7709
FT Turnbuckle Wrench
12mm Big Bore Shock Tool
FT Off Road Ride Height Gauge
FT Hex Driver Set, (7 pcs)
FT .050” Silver Hex Driver
FT 1/16” Black Hex Driver
FT 1.5mm Purple Hex Driver
FT 5/64” Blue Hex Driver
FT 3/32” Gold Hex Driver
FT 2.5mm Green Hex Driver
FT 3mm Red Hex Driver
FT Phillips Silver Screwdriver
FT Silver Spring Hook Tool
FT Nut Driver Set, (6 pcs)
FT 3/16” Black Nut Driver
FT 1/4” Red Nut Driver
FT 5.5mm Red Nut Driver
FT 11/32” Green Nut Driver
FT 8mm Gold Nut Driver
FT 5/64” Blue Ball Hex Driver
FT 3/32” Gold Ball Hex Driver
FT Ball Hex Driver Set, (3 pcs)
FT 8-Piece 1/4” Hex Drive Set
FT 1/4” Hex Drive Handle, without tips
FT 1/4” Hex Drive .050” Tip
FT 1/4” Hex Drive 1/16” Tip
FT 1/4” Hex Drive 5/64” - 2.0mm Tip
FT 1/4” Hex Drive 3/32” Tip
FT 1/4” Hex Drive 1.5mm Tip
FT 1/4” Hex Drive 2.5mm Tip
FT 1/4” Hex Drive 3/16” Nut Driver Tip
FT 1/4” Hex Drive 1/4” Nut Driver Tip
FT 1/4” Hex Drive 11/32” Nut Driver Tip
FT 1/4” Hex Drive 5.5mm Nut Driver Tip
FT 1/4” Hex Drive 7.0mm Nut Driver Tip
FT 1/4” Hex Drive 8.0mm Nut Driver Tip
FT 1/4” Hex Drive 5/64” - 2.0mm Ball End Tip
FT 1/4” Hex Drive 3/32” Ball End Tip
FT 1/4” Hex Drive Standard Screwdriver Tip
FT 1/4” Hex Drive Phillips Screwdriver Tip
FT 1/4” Hex Drive 2.5mm Ball End Tip
FT 1/4” 5 Piece Power Tool Tips Set (5/64-2.0mm,
1.5mm, 2.5mm, 5/64”- 2.0mm ball, 2.5mm ball)
FT Camber + Track Width Tool
FT Body Scissors
12 Inch Nylon Wire Ties
6 Inch Nylon Wire Ties
8 Inch Nylon Wire Ties
Composite Droop Gauge
Shock Building Tool
Molded Tools, Set
V2 Stamped Multi-tool
4 Inch Nylon Wire Ties
:: RePlay Cameras
1
RP001
1
RP002
1
RP021
RP022
1
RP023
RP024
1
RP029
1
RP030
1
RP032
1
RP033
1
RP034
1
RP036
RP038
1
RP041
RP042
RP043
RP044
RP045
RP046
1
RP047
1
RP048
1
RP049
1
RP054
1
1
1
1
1
1
1
1
:: Apparel
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
SP420**
:: Notes
1
1
1
1
1
1
1
1
1
110684
12
12
12
1
1
1
1
12
SP31**
SP32**
SP37**
SP38
SP39
SP71**
SP77**
SP78**
SP79**
SP84**
SP86**
SP90**
SP91**
SP92**
SP93**
SP94**
SP95**
SP96**
SP97**
SP98**
SP416
SP417
SP421S
SP421L
SP422S
SP422L
SP423S
SP423L
SP424S
SP424L
Replay XD1080 Complete Camera System
Replay XD720 Complete Camera System
Replay XD1080 Lens Bezel Kit
Replay XD1080 Clear Lens Cover
Replay XD1080 Lens Bezel & Rear Cap O-Ring
Replay XD Lens Bezel
Replay XD1080 HDMI to Mini-HDMI
Replay XD1080 Mini 8-pin USB Charge Data Cable
USB DC Car Charger 1A Stubby
USB DC Car Charger 500mAh
Micro SDHC USB Reader
3M VHB 4991 Mount Adhesive for SnapTray
3M VHB 5962 Mount Adhesive for SnapTray
Replay XD Suction Cup Arm Mini Clamp
Replay XD Suction Cup Short Arm Base
Replay XD Skateboard Mount
Replay XD VHB SnapTray, Convex
Replay XD VHB SnapTray, Flat
Au Plug for Universal DC Wall Charger
Eu Plug for Universal DC Wall Charger
Uk Plug for Universal DC Wall Charger
Universal USB DC Wall Charger 1A
Replay ReView Field Monitor
27 Time WC T-Shirt, Black (S, M, L, XL, 2XL, 3XL)
Kids AE 2012 T-Shirt, Blue (S, M, L)
Reedy 2012 T-shirt - Black (S, M, L, XL, 2XL, 3XL)
Reedy Trucker Hat
Reedy Patch
Associated Winter Jacket (M, L, XL)
AE 2012 T-Shirt, Blue (S, M, L, XL, 2XL, 3XL)
AE 2012 T-Shirt, White (S, M, L, XL, 2XL, 3XL)
AE 2012 T-Shirt, Black (S, M, L, XL, 2XL, 3XL)
Reedy 3D T-Shirt, Black (S, M, L, XL, 2XL, 3XL)
Reedy Womens 3D T-Shirt, Black (S, M, L, XL)
AE Retro T-Shirt, Blue (S, M, L, XL, 2-5XL)
AE Retro T-Shirt, Black (S, M, L, XL, 2-5XL)
AE Retro T-Shirt, White (S, M, L, XL, 2-5XL)
2013 Worlds T-Shirt, Blue (S, M, L, XL, 2-5XL)
2013 Worlds T-Shirt, Black (S, M, L, XL, 2-5XL)
2013 Worlds Hoodie, Black (S, M, L, XL, 2-3XL)
AE Retro Womens T-Shirt, Pink (S, M, L, XL)
AE Retro Womens T-Shirt, Black (S, M, L, XL)
AE Womens T-Shirt, Black (S, M, L, XL)
Associated Car Carrier Bag, Medium
1/10 FT Motor Bag
AE Pit Gloves (L, XL)
AE 2012 Hat, Black, Flat Bill, S/M
AE 2012 Hat, Black, Flat Bill, L/XL
AE 2012 Hat, Black, Curved Bill, S/M
AE 2012 Hat, Black, Curved Bill, L/XL
AE 2012 Hat, White, Flat Bill, S/M
AE 2012 Hat, White, Flat Bill, L/XL
AE 2012 Hat, White, Curved Bill, S/M
715
AE 2012 Hat, White, Curved Bill, L/XL
Reedy 2009 Track Banner
Team Associated Track Banner
** Use part number plus the desired size when ordering!
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Pr.
1
1
1
1
1
1
1
1
1
1
Page 30
30
:: Notes
:: Contact Information
Associated Electrics, Inc.
26021 Commercentre Drive
Lake Forest, CA 92630-8853 USA
http://www.TeamAssociated.com
http://www.RC10.com
http://twitter/Team Associated
http://bit.ly/AEonFacebook
call: (949) 544-7500
fax: (949) 544-7501
Check out the following web sites for all
of our electric kits, current products, new
releases, setup help, tips, and racing info!
www.TeamAssociated.com. - www.RC10.com
Page 31
Front Suspension:
Camber: °
Total Toe: °
Ride Height:
Arm Type:
Tower Type:
Caster Block Insert: °
Kick-Up Angle: °
Notes:
-1
0
24mm
Kit
Kit
5
25
Driver: Date:
Track: Event:Setup Sheet
Axle Height:
Bump Steer
Spacing:
0mm
Steering
Stop
Spacing:
Trailing Axle
Insert:
2mm 3mm 4mm
Up
Middle
Down
A
B
Ball Stud
Spacing:
Ball Stud
Spacing:
2mm
2mm
3
2
1
12
Rear Suspension:
Camber: °
Ride Height:
Hub Spacing:
Forward Middle Back
Notes:
Electronics:
Radio: Servo:
EPA: Throttle: % Brake: %
ESC:
ESC Settings:
Motor:
Wind: Timing:
Pinion: Spur:
Battery:
Battery Position:
Track Info:
Size:
Surfaces:
Traction:
Moisture:
Condition:
Temperature:
Notes:
Race Results:
Qualify: Main:
Finish: TQ:
Best Lap Time:
Small
Dirt
Low
Dry
Bumpy
Ambient: Track:
-1
24mm
Medium
Carpet
Medium
Damp
Outdoor
Grooved
:: For more setups, visit RC10.com and click on “Setup Sheets”
Large
Astroturf Multi Surface
High
Wet
Dusty
Smooth
2mm 0mm
Caster Block Spacing:
Anti Roll Bar:
None
Black (1.2mm)
Silver (1.3mm)
Gold (1.4mm)
Rear Hub Link Setting:
A
B
Arm Mount:
Inboard Toe: °
Anti-Squat: °
Drivetrain:
Differential:
Ball:
Setting:
Gear:
Oil:
Slipper Clutch:
Type:
# of Pads:
Notes:
Tires:
Extra Large
Very High
Hard PackedIndoor
Loamy
Vehicle Comments:
Tires (F/R):
Compound (F/R):
Insert (F/R):
Wheel (F/R):
Notes:
Body & Wing:
Body:
Wing:
Wing Angle: 0° 3° 6°
Notes:
3
1
Tight
VTS
3
CBBAA
0° 0.5° 1°
Up
Down
Up
Down
Hub Insert:
Shocks:
Piston:
Oil:
Spring:
Limiters:
Cup Offset:
Stroke:
Free Length:
Notes:
A
B
Ball Stud
Spacing:
2mm
AB
Front Rear
1.6
32.5 wt
White
2
5mm
RC10B5M Stock
RC10B5M Stock
Total Vehicle Weight:
1.7
32.5 wt
Green
2
5mm
/
/
/
/
3
2
1
12
Free
Length
Stroke
Page 32
:: Hardware - 1:1 Scale View
32
Button Head (bhcs)
3x8mm Aluminum (8552)
2x4mm (31510)
2.5x6mm (32520)
2.5x8mm (31521)
3x4mm (91158)
3x5mm (31530)
3x6mm (31531)
3x8mm (31532)
3x10mm (25211)
3x12mm (89202)
3x14mm (25187)
3x16mm (89203)
3x18mm (2308)
3x22mm (25189)
3x24mm (89204)
3x30mm (91478)
Flat Head (fhcs)
3x8mm Aluminum (8553)
Ballstuds
Ti Nitride HD 6mm (91118)
Ti Nitride HD 8mm (91119)
Ti Nitride HD 10mm (91120)
Ti Nitride HD 12mm (91121)
Nuts (lock/plain)
M3 Alum. Locknut, Blue (31550)
3x8mm (25201)
3x10mm (25202)
3x12mm (25203)
3x14mm (89208)
3x16mm (25204)
HD 6mm (91047)
HD 8mm (91048)
HD 10mm (91049)
HD 12mm (91050)
M3 Nut (91477)
Ball Bearings
3x7x3mm (91475)
5x8mm (31400)
5x10x4mm (25237)
6x12x4mm (25238)
6x13x5 (91476)
10x15x4 (25616)
Set Screws
3x3mm (25225)
3x8mm (4670)
Shims and Washers
Servo Mount Washer (7337)
(.250 x .125 x .815)
FT Ballstud Washer, Aluminum
(1mm and 2mm, 4 each) (31286)
Notes:
M3 Locknut w/Flange (25612)
FT 3mm Locknuts, Blue(25392)
M4 Locknut w/Flange (91148)
FT M4 Locknuts w/Flange,
Blue (31551)
3x16mm (4689)
Clips
E-clip 1/8 (6299)
Diff Balls
5/64 Diff Thrust Balls (6574)
3/32 Carbide Diff Balls (6581)
Page 33
Front Suspension:
Camber: °
Total Toe: °
Ride Height:
Arm Type:
Tower Type:
Caster Block Insert: °
Kick-Up Angle: °
Notes:
Rear Suspension:
Camber: °
Ride Height:
Hub Spacing:
Forward Middle Back
Notes:
Driver: Date:
Track: Event:Setup Sheet
Axle Height:
Up
Down
Up
Down
Up
Middle
Down
A
B
Ball Stud
Spacing:
B
Ball Stud
Spacing:
Bump Steer
Spacing:
Steering
Stop
Spacing:
Caster Block Spacing:
Anti Roll Bar:
None
Black (1.2mm)
Silver (1.3mm)
Gold (1.4mm)
Trailing Axle
2mm 3mm 4mm
Insert:
Rear Hub Link Setting:
CBBAA
A
B
Ball Stud
Spacing:
A
3
2
1
3
2
1
12
Electronics:
Radio: Servo:
EPA: Throttle: % Brake: %
ESC:
ESC Settings:
Motor:
Wind: Timing:
Pinion: Spur:
Battery:
Battery Position:
Track Info:
Size:
Surfaces:
Traction:
Moisture:
Condition:
Temperature:
Notes:
Race Results:
Qualify: Main:
Finish: TQ:
Best Lap Time:
Small
Dirt
Low
Dry
Bumpy
Medium
Carpet
Medium
Damp
Outdoor
Grooved
Ambient: Track:
:: For more setups, visit RC10.com and click on “Setup Sheets”
Large
Astroturf Multi Surface
High
Wet
Dusty
Smooth
Arm Mount:
Inboard Toe: °
Anti-Squat: °
Drivetrain:
Differential:
Ball:
Setting:
Gear:
Oil:
Slipper Clutch:
Type:
# of Pads:
Notes:
Tires:
Extra Large
Very High
Hard PackedIndoor
Loamy
Vehicle Comments:
Tires (F/R):
Compound (F/R):
Insert (F/R):
Wheel (F/R):
Notes:
Body & Wing:
Body:
Wing:
Wing Angle: 0° 3° 6°
Notes:
Hub Insert:
0° 0.5° 1°
Shocks:
Piston:
Oil:
Spring:
Limiters:
Cup Offset:
Stroke:
Free Length:
Notes:
Total Vehicle Weight:
12
AB
Front Rear
Free
Length
Stroke
/
/
/
/
Page 34
current products, new releases, setup help, tips, and racing info!
Check out the following web sites for all of our kits,
www.TeamAssociated.com. - www.RC10.com
call: (949) 544-7500 - fax: (949) 544-7501
http://twitter/Team_Associated
http://bit.ly/AEonFacebook
http://www.TeamAssociated.com
Lake Forest, CA 92630 USA
26021 Commercentre Dr.
http://www.RC10.com
Associated Electrics, Inc.
Loading...