How it Works
Teac
Loading...
DA-88
Quick Reference
8 pgs223.17 Kb0

Teac DA-88 Quick Reference

DA-88 quick ref.doc 10/14/97 7:27 PM
Page 1
© TEAC America, Inc., 1997 All rights reserved.
BASIC FUNCTIONS Software Version 4.01
Items marked SY are only available when the SY-88 is installed.
Function Display
To Enter Function To Enter
Data
Remarks
1 Display ABS Time ABS
Hold DISPLAY +
--
2 Display H:M:S:F TC difference DIFF SY DISPLAY - ­3 Display Sub-Frame difference “ SY DISPLAY -
Press
to return to H:M:S:F display
4 Auto Offset Calculate & Store “ SY DISPLAY
and
Time code offset only
5 Display Generator Start Time & Enter
Data
GEN SY DISPLAY
or
-
6 Column by column Generator or
Offset time Setting
GEN
or
OFFSET
Hold
and
then
press DISPLAY
or
A period will start blinking in the Hours column, use
or
to enter hours. Press DISPLAY to move the period to next column. After setting last column, pressing DISPLAY will exit column setting mode
7 Display MEMO 1 & Enter data MEMO 1 DISPLAY
or
By pushing MEMO 1, point can be set on the fly
8 Display MEMO 2 & Enter data MEMO 2 DISPLAY
or
By pushing MEMO 2, point can be set on the fly
9 Display OFFSET & Enter data OFFSET DISPLAY
or
ABS time Offset entry in Frames only.
10 Display OFFSET & Enter Data “ SY DISPLAY
or
SMPTE T/C Offset entry in Frames, or when DISPLAY is pressed again, in Sub-Frames.
11 Display PITCH & Enter data PITCH DISPLAY or VARI
or
-
12 Display Tape Time Code TC SY
Hold DISPLAY +
--
13 Display User Bits on tape SY
Hold
+ DISPLAY
-
TC LED will flash
14 Display Incoming Time Code “ SY
Hold
+
Display
- TC LED will flash. Press DISPLAY to exit.
15 Pull Up / Down mode setting “ SY
Hold
and press Fs
or
Press DISPLAY to exit
16 Display Pull Up / Down Status Any SY Press Fs button
-
Display will exit automatically
DA-88 quick ref.doc 10/14/97 7:27 PM
Page 2
© TEAC America, Inc., 1997 All rights reserved.
Basic Functions cont. Software Version 4.01
Items marked SY are only available when the SY-88 is installed.
Function Display
To Enter Function To Enter
Data
Remarks
17 Slave reference, Time Code or ABS
time
ABS SY
Press
&

or
Press DISPLAY to exit
18 Digital or Analog output mode
selection
Hold
press Digital In
- This sets a 43Fs delay on all 8 tracks for digital dubbing. Display will exit automatically
19 Track Delay
Hold
press DISPLAY
or
Press Track Assign to select track to delay. Press DISPLAY to exit
20 ALL Track Delay
Hold
press DISPLAY then Hold Rec. for track 1 & press Rec. for track 2
or
If no change is made, individual track delay values are retained. Press DISPLAY to exit
21 Crossfade
Hold
press DISPLAY
or
Press DISPLAY to exit
22 Shuttle Monitor Mode
Hold
press SHUTTLE
or
When ON this will mute all tracks not in Rec Ready when in shuttle mode. Rec Ready tracks will switch to Input. Press DISPLAY to exit
23 OFFSET Tally, On / Off
Hold
press CHASE
or
Press DISPLAY to exit
24 Punch In point Display & Modify MEMO 1 Perform Rehearsal
or
Press DISPLAY +  to Exit or DISPLAY to go to Punch out point
25 Punch Out point Display & Modify MEMO 2 Perform Rehearsal
or
Press DISPLAY +  to Exit
26 Display Preroll and Enter or modify
data
ABS
Press
&  when Rehearsal or Auto In LED is blinking or On
or
Press DISPLAY +  to Exit
27 Greeting ABS
In TEST mode Hold
+
+ DISPLAY + and press remote. Release
&
first then DISPLAY
or
and
DISPLAY
Use
or
to scroll through letters. Press
DISPLAY after each correct letter. Press
&
when done to Exit message mode. Reboot.
28 Display Errors Any Press REMOTE button
when in TEST mode
-
Track Meters 1 & 2 show Block Error Rate in real time for playback heads A & B
29 Enter SY-88 Menu System TC SY
Press
&
-
This enters the SY-88 Menu system
30 Exit SY-88 Menu System “ SY
Hold DISPLAY press
-
This will exit SY-88 Menu system
31 Chase Record Enable ABS
Hold  press TC Rec button
or
Allows front panel Record command on slave units. Must have SYS version.34.02
32 20dB or 16dB Headroom Select ABS Hold press ALL INPUT
or
Requires Modification & SYS ver 61.03
DA-88 quick ref.doc 10/14/97 7:27 PM
Page 3
© TEAC America, Inc., 1997 All rights reserved.
SY-88 MENU FUNCTIONS Software Version 4.01
These items are available after you enter the SY-88 Menu System by switching display to TC and pressing  and
simultaneously.
Once in
the Menu System, pressing DISPLAY will scroll forward through the Menu Items. Holding DISPLAY and pressing
will scroll back to the previous
Menu items, Holding DISPLAY and pressing
will exit the Menu system.
Display Description
Item Choices Setting Dip
No Item Item Sw
Default Default
1 Select DA-88 Time Base Select operating Frame rate: 30 ndF, 29 ndF, 29 dF, 25 F and 24 F 2 t Display Only Displays Frame Rate of time code recorded on tape 3 t.out tc Abs ABS to TC conversion off on
The following menus are available DA-88 SYS Ver 3.10 or later, and SY-88 Ver 4.01
S1-#2 Must be in the down position for 9-pin control
4 ChS rEch FrEE Chase Mode rechase free S1 #3 5 vSync OFF on Video Sync Off On S1 #7 6 tCt. AnLG dGEL Time code timing analog digital S1 #5 7 rEnt. EnA dSA 9-pin Remote control Enable Disable 8 d. Device Type (See table 2) 9 pin device Ack. (See Table 2) S3 #1,2,3
9 rcdLy. Record delay (See Manual) Record Delay See Manual for settings 10 trKArm. on oFF Track arming enable disable S3 #7 11 tm. Track Mapping (See Table 3) Track Mapping See Table 3 for settings S3 #4&5 12 Shtmute 0 1 Shuttle Mute don’t mute mute 13 FASt. 8 100 Fast wind speed X8 X100 S3 #6 14 CutLy. StP StL Cue up tally Stop Still S3 #8 15 morE… 0 1 More Menu No Yes
The following Menu items are available only when item 15, more is set to 1
16 v. Example 4.01. 3 Software Version (Display only) 17 rEchwd. 1 2 Rechase Window 1 second 2 seconds S1 #4 18 vsy. FrEE rESy Video re-Sync mode Free Re-Sync 19 LtC. LEAP 5F LTC mode leap 5 frames S1 #8 20 tCrEc 0 1 9-pin TC record enable Disable Enable 21 PSP. mute on Pgm Spd Play mode mute don’t mute 22 rESEt Reset to factory defaults 23 rEAd Read current hardware switch settings
Loading...
+ 5 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use