VIF FREQUENCY :
SIF FREQUENCY :
CHROMA IF FREQUENCY :
INTER-CARRIER FREQUENCY :
SCANNING HORIZONT AL :
VERTICAL :
ANTENNA INPUT IMPEDANCE :
CRT :
SM -38PM P. 1
PAL - I / I
4 - 13
21 - 69
38.9
32.9
34.47
6.0
PAL - BG
2 - 4
5 -12
21 - 69
38.9
33.4
34.47
5.5
PAL - I
(UK)
21 -69
39.5
33.5
35.07
6
PAL - SECAM -
BG / DK
1 - 5
6 - 12
21 - 69
38.0
31.5 32.5
33.57 33.57
6.5 5.5
PAL - SECAM -
BG / DK
( HYPER )
1 - 5
6 - 12
21 - 69
38.9
32.4 33.4
34.47 34.47
5.5 6.5
15625 LINE
50 Hz
75 OHM
34" 38"
PAL - BG
( HYPER )
E2 - S10
E5 - S41
E21 - E69
38.9
33.4
34.47
5.5
PAL - BG
( CATV )
E2 - S2
E5 - S20
E21 - E69
38.9
33.4
34.47
5.5
SECAM -
L
1 - Q
21 - 69
38.9
32.4
34.47
6.5
L'
FB - FC
32.7
39.2
6.5
P AL-DK
1-5
6-12
13-57
38
31.5
33.57
6.5
CH
CH
CH
MHz
MHz
MHz
MHz
ITEMS OF MEASUREMENT
VIDEO SENS. AT S/N 30db
L - VHF
H - VHF
UHF
STANDARD
34"
< 57
< 57
< 60
STANDARD
38"
< 57
< 57
< 60
UNIT
dbuv
dbuv
dbuv
SOUND SENS. AT S/N 30db
AGC CHARACTER
SELECTIVITY -1.5 MHz
+ 8 MHz
COLOR SENS.
COLOR LOCK - IN RANGE
VERTICAL LOCK - IN RANGE
HORIZONTAL LOCK - IN RANGE
MAX BRIGHTNESS
MAX OUTPUT POWER
OUTPUT POWER AT 10% THD
BUZZ
AFC RANGE
1. Never disconnect any leads while receiver is in operation.
2. Disconnect all power before attempting any repairs.
3. Do not short any portion of the circuit while power is on.
4. For safety reasons, all parts replaced should be identical, ( for parts and part numbers see parts list ).
5. Before alignment the set must be pre-heated for 30 minutes or more and erase magnetism thoroughly
from CRT front chassis frame by erase coil. ( Except IF, SYNC, COLOR, SECAM, B+, SOUND )
II.
TEST EQUIPMENT
1. Colour Bar, Dot, Cross Hatch Generator
2. DC Power Supply
3. Oscilloscope
4. Vacuum Tube Voltmeter
5. Volt Ohmmeter
6. High Voltage Meter
7. Ampere Meter ( 0.5 Class, DC 3mA Max )
8. Demagentizing Coil
9. Philips Pattern Generator
10. High Pot Tester
III. FACTORY ADJUSTMENT : See table 1- 4
1. Press REMOTE FACTOR Y ON button.
2. Press REMOTE FACTO RY button.
3. Press REMOTE UP or DOWN button select item.
4. Press REMOTE value (+) (-) button,adjust the value.
5. REMOTE DIALOG CENTRE button can turn off factory mode function.
REMARK : NO this factory on Normal remote control .
IV.B+ ADJUSTMENT
1. Connect a digital voltmeter between the W237 and Ground.
2. Press REMOTE Picture button.
3. Press REMOTE UP/DOWN and value (-) button set Brigntness,contrast,color to minimum.
4. Adjust Screen Volume on FBT Until the picture can just been seen
5. Adjust VR901 and obtain a reading of 143V +1V (DC).
.
V. AGC ALIGNMENT
1. Receive CH69 ( UHF ) and input field strength.
2. Connect a digital voltmeter between the TUNER AGC TERMINAL and Ground.
3. Press REMOTE AGC button.
4. Press REMOTE value (+) (-) button adjust value to (0) and then adjust AGC take over value
obtain drop down 0.4V. (DC)
REMARK : ( 1/ The drop down voltage should be more than and tends to 0.2V )
( 2/ No observable noise can be seen )
SM - 38PM P. 3
VI. SOUND TRACKING ALIGNMENT
1. Receive a gray scale pattern.
2. Connect a oscilloscope and monitor IC202 PIN 13 and Ground.
3. Adjust T200 to obtain the waveform Fig.6.Connect a volt meter to IC202 PIN15
and GND,adjust T200 to obtain 2.7+0.1V.
Fig.6
Remark: All frequency of Marker points are +0.2% tolerance.
VII. EAST - WEST CORRECTION ADJUSTMENT
1) Receive a crosshatch and center cross pattem.
2) Set the Brightness,contrast to middle position.
3) Press REMOTE EW-Par/wid,EW-trap button,Press REMOTE VALUE (+) (-) button adjust Value
to normal regular picture.
4) Press REMOTE WE-width button,Press REMOTE value (+) (-) button adjust value to proper horizontal
width ( 90% + 2% )
VIII. HORIZONT AL SHIFT ADJUSTMENT
1. Receive Monoscope Pattern input signal 70dB +10dB.
2. Press REMOTE H-shift button.
3. Press REMOTE value (+) (-) button adjust value to obtain the picture at center +2mm.
( Specification show in Fig.8 )
IX. VERTICAL LINEARTY ADJUSTMENT
1) Receive a cross hatch and center cross pattem.
2) Set the Brightness,contrast to middle position.
3) Press REMOTE V-SIope,S-Correction button,Press REMOTE Velue (+) (-) button adjust value to normal
regular picture.
4) Press REMOTE V-Shift button,Press REMOTE Value (+) (-) button adjust value to obtain the picture at center.
X. VERTICAL AMPL ADJUSTMENT
1. Receive the Monoscope Pattern.
2. Press REMOTE V-ampl button.
3. Press REMOTE value (+) (-) button adjust value to obtain a normal picture.
XI. WHITE BALANCE ALIGNMENT STEP
( Degauss the picture by degaussing coil if necessary )
1. Receive a black and white pattern.
2. Press REMOTE picture button.
3. Press REMOTE UP/DOWN and value (-) button set the brightness,contrast,
colour to minimun.
4. Adjust screen volume on FBT unitl the picture can just been seen.
5. Press REMOTE sub bri button.
6. Press REMOTE value (+) (-) button adjust value to (31).
7. Press REMOTE with bal button.
8. Press REMOTE Value (+) (-) button adjust value to (1) see the picture at horizontal line.
9. Adjust screen volume on FBT until the horizontal line can just been seen.
10. Repeat item 7.8 Can obtain normal screen.
SM - 38PM P. 4
XII.SUB - BRIGHTNESS ALIGNMENT
1. Receive a colour bar pattern.
2. Press REMOTE picture button,.
3. Press REMOTE UP/DOWN and value (-) button set the brightness, contrast to minimun.
4. Press REMOTE sub bright button.
5. Press REMOTE value (+) (-) button adjust value to brightess bar can just be seen.
XIII. FOCUS ALIGNMENT
1) Set the Brightness and Contrast to middle position.
2) Receive a monoscope pattern.
3) Adjust focus control to obtain sharpest picture.
XIV. PINCUSHION CORECTION ALIGNMENT
1. Thg TV Set face to east.
2. Receive a cross hatch patten.
3. Adjust VR020 to change the amplitude of pin cushion corection.
4. Adjust L020 to change the balance of horizontal line.
Repeat item (3) , (4) until best condition.
PCB 190-283300-20
XV. HIGH POT TESTING
1) Short the L - pole and N - pole of AC line cord.
2) Switch on the power switch of the TV Set.
3) Connect The High Pot Tester ( - ) to L and N pole, ( + ) to the METAL PART of CABINET.
CONDITION
SAFETY STD.
VDE, SAA
BS
CHINA STANDARD
UL
TEST STANDARD
3.0KV 10mA / 1MIN
4.0KV 10mA / 1MIN
3.0KV 10mA / 1MIN
1.0KV 5mA / 1MIN
TEST ST ANDARD
FOR PRODUCTION
>3.5 KV <10mA / >10 SEC.
>4.0 KV <10mA / >10 SEC.
>3.3 KV < 5mA / > 6 SEC.
>1.25KV < 5mA / > 1 SEC.
Remark:
1) If no other specify, the strength of input signal should be 70dB +10dB.
2) The High Pot Tester can have < +5% tolerance.
SM - 38PM P. 5
DISTRICT
CENTRE (mm)
POSITION
LIMIT (mm)
SCANNING
SIZE (%)
SCANNING
SIZE
LIMIT (%)
THAILAND
FRANCE
GERMANY
*GROUP A
*GROUP B
*GROUP C
mm -5 -4 -3 -2 -1 0 1 2 3 4 5 mm
LEFTRIGHT
-1
+3
+3
-2
0
+3
0 ~ -2
0 ~ +5
0 ~ +5
-5 ~ -1
-2 ~ +2
0 ~ +5
CENTRE OF
THE SCREEN
90
90
90
90
90
90
CRT MUST
FACE TO EAST
88 ~ 92
88 ~ 94
90 ~ 95
88 ~ 94
88 ~ 94
88 ~ 94
FIG. 8
REMARK :
1. SUITABLE FOR 14" OR ABOVE TV.
2. Adjust the centre position must take the upper side of monoscope
pattern for standard.
3. Group A : AUSTRALIA, NEW ZEALAND, TAHITI.
4. Group B : HONG KONG, CHINA, AMERICA, CANADA, MALAYSIA,
MEXICO.
5. Group C : ENGLAND, ITAL Y, GERMANY, RUSSIA, SWITZERLAND,
JUGOSLAVIA, SPANISH.
If the above countries are not include, please consult to
Engineering Dept.
SM - 38PM P. 6
FACTORY MODE TABLE 1
REF
ITEM
REMARK
VALUE
AVL
1
2
3
4
5
POWER
TDA884X
S.SYS
LOGO
CTI
OSD.
6
LANGUAGE
ANTENNE
7
WOOFER
0
P
3
1
2
1
0
0
0
1
0= OFF 1 = SHORT DECAY
2 = MEDIUM DECAY 3=LONG DECA Y
O = TV Status S = Power Status P = Last power status
1=PAL/NTSC.W/O EW 3=PAL/NTSC.W/EW
2=PAL/SECAM/NTSC.W/O EW 4=PAL/SECAN/NTSC,W/EW