Taylor Freezer C303, C314 Operation Manual

Models C303 & C314

Slush Freezers

Operating Instructions

066732-M

8/19/10

Complete this page for quick reference when service is required:

Taylor Distributor:
Address:
Phone:
Fax:
E-mail:
Service:
Parts:
Date of Installation:

Information found on the data label:

Model Number:
Serial Number:
Electrical Specs: Voltage Cycle

Phase
Maximum Fuse Size: A
Minimum Wire Ampacity: A

E August, 2010 Taylor

All rights reserved.
066732-M

The word Taylor and the Crown design
are registered trademarks in the United States
of America and certain other countries.

Taylor Company
750 N. Blackhawk Blvd.
Rockton, IL 61072

Table of Contents

Section 1 To th e Installer 1............................................

Section 2 To the Operator 4...........................................

Compressor Warranty Disclaimer 4.......................................

Section 3 Safety 5....................................................

Section 4 Operator Parts Id entification 7...............................

Model C303 7..........................................................

Model C314 8..........................................................

Beater Door Assembly 9.................................................

Accessories 10..........................................................

Section 5 Important: To the Operator 11.................................

Control Switch 11........................................................

Liquid Crystal Display 11..................................................

Operational Mode Displays 12.............................................

Operator Menu Display 12................................................

Syrup Out Indicator 19....................................................

CO2 Out Indicator 19.....................................................

Water Out Indicator 19....................................................

Audio Alarm Silencer 19..................................................

Product Not Ready Light 19...............................................

Sampling Valve 19.......................................................

Daily Procedures 19......................................................

Section 6 Operating Procedures 20.....................................

Assembly 20............................................................

Sanitizing 25............................................................

Priming/Brixing 27........................................................

Models C303 & C314 Table of Contents

Table of Contents - Page 2

120 Day Closing Procedure 30............................................

Draining Product From the Freezing Cylinders 30............................

Rinsing 31..............................................................

Cleaning 31.............................................................

Disassembly 32..........................................................

Brush Cleaning 33.......................................................

Section 7 Important: Operator Checklist 34..............................

During Cleaning and Sanitizing 34.........................................

Troubleshooting Bacterial Count 34........................................

Regular Maintenance Checks 34...........................................

Winter Storage 35........................................................

Section 8 Troubleshooting Guide 36....................................

Section 9 Parts Replacement Schedule 38...............................

Section 10 Parts List 39.................................................

Wiring Diagrams 48......................................................

Note: Continuing research results in steady improvements; therefore,information
in this manual is subject to change without notice.

E August, 2010 Taylor

All rights reserved.
066732-M

The word Taylor and the Crown design
are registered trademarks in the United States
of America and certain other countries.

Table of Contents Models C303 & C314

Taylor Company
750 N. Blackhawk Blvd.
Rockton, IL 61072

Section 1 To the Installer

The following are general installation instructions.
For complete installation details, please see the
checkout card.

Site Preparation

Review the area where the unit will be installed
before uncrating the unit. Make sure all possible
hazards to the user or equipment have been
addressed.

For Indoor Use Only: This unit is designed to
operate indoors, under normal ambient
temperatures of 70° - 75°F (21° - 24°C). The freezer
has successfully performed in high ambient
temperatures of 104°(40°C) at reduced capacities.

This unit must NOT beinstalledinanarea
where a water jet or hose can be used. NEVER use
a water jet or hose to rinse or clean the unit. Failure
to follow this instruction may result in electrocution.

This unit must be installed on a level surface
to avoid the hazard of tipping. Extreme care should
be taken when moving this equipment for any
reason. Two or more persons are required to safely
move this unit. Failure to comply may result in
personal injury or equipment damage.

Uncrate the unit and inspect it for damage. Report
any damage to your Taylor Distributor.

Air Cooled Units

Air cooled units require a minimum of 3” (76 mm) of
air space both sides, 3” (76 mm) at the rear, and 12”
(305 mm) on the top of the unit. Minimum air
clearances must be met to assure adequate air flow
for optimum performance.

Installer Safety

In all areas of the world, equipment should
be installed in accordance with existing local codes.
Please contact your local authorities if you have any
questions.

Care should be taken to ensure that all basic safety
practices are followed during the installation and
servicing activities related to the installation and
service of Taylor equipment.

S Only authorized Taylor service personnel

should perform installation and repairs on
the equipment.

S Authorized service personnel should consult

OSHA Standard 29CFRI910.147 or the
applicable code of the local area for the
industry standards on lockout/tagout
procedures before beginning any installation
or repairs.

S Authorized service personnel must ensure

that proper PPE is available and worn when
required during installation and service.

S Authorized service personnel must remove

all metal jewelry, rings, and watches before
working on electrical equipment.

This piece of equipment is made in the USA and has
USA sizes of hardware. All metric conversions are
approximate and vary in size.

Models C303 & C314 To the Installer

cause severe injuries.

1

This unit has many sharp edges that can

Water Cooled Refrigeration Units
(Water Cooled Units Only)

It is always a good practice to have a filter system to
improve the quality of the water and to avoid
clogging the operating components.

On the back of the unit, two additional 3/8” (9.5 mm)
F.P.T. water connections for condenser inlet and
outlet have been provided for easy hook-up. 3/8”
(9.5 mm) inside diameter water lines should be
connected to the machine. Flexible lines are
recommended if local codes permit. Failure to use
adequate size water lines may cause the unit to go
out on high head pressure and shut down.

Depending on local water conditions, it may be
advisable to install a water strainer to prevent
foreign substances from clogging the automatic
water valve.

DO NOT INSTALL A HAND SHUT-OFF VALVE ON
THE “OUT” LINE! Water cooled units are counter
flow and the water should flow in this order: First,
through the automatic water valve. Second, through
the inlet located at the bottom of the condenser.
Third, through the outlet fitting located at the top of
the condenser toanopentrapdrain.

IMPORTANT: Water pressures are pre-set at the
factory. Do not adjust the water pressure.
Improper water adjustments may cause operation
discrepancies.

IMPORTANT: The water filter (064422-SER) must
be thoroughly flushed with water before connecting it
to the machine. This removes any loose particles
present from the manufacture of the filter that could
clog the flow control. To flush the filter, connect the
inlet end of the filter to the water supply. Position the
outlet end of the filter over an empty pail. Open the
water supply. Allow water to flow through the filter
until the water exiting the filter is clear. Close the
water supply. Attach the outlet end of the filter to the
machine. Reopen the water supply.

Figure 1

Water Connections

An adequate cold water supply must be provided
with a hand shut-off valve. On the back of the
remote carbonat or , a 3/8” (9. 5 m m ) M.F.L. water
connection has been provided for easy hook-up. A
flexible line is recommended, if local codes permit. A
minimum of 25 psi (1.7 bar) water pressure is
required to avoid having the unit cut out the low
water pressure switch. A booster pump must be
provided if this pressure is not available.

Note: Water lines beyond 200 ft. (61 m) require 1/2”
(13 mm) water lines.

INSTALL POTABLE WATER CONNECTION
WITH ADEQUATE BACK-FLOW
PROTECTION TO COMPLY WITH
APPLICABLE NATIONAL, STATE AND
LOCAL CODES.

Electrical Connections

Each freezer requires two power supplies. One for
the main unit and one for the remote carbonator.
Check the data label on the freezer for fuse, circuit
ampacity and electrical specifications. Refer to the
wiring diagram provided inside the control box for
proper power connections.

In the United States, this equipment is intended to
be installed in accordance with the National
Electrical Code (NEC), ANSI/NFPA 70-1987. In all
other areas of the world, equipment should be
installed in accordance with the existing local codes.
Please contact your local authorities.

The purpose of the NEC code is the practical
safeguarding of persons and property from hazards
arising from the use of electricity. This code contains
provisions considered necessary for safety.

The NEC is a United States regulatory agency.
International users must follow local electrical codes.

2

Models C303 & C314To the Installer

DO NOT operate this freezer with larger
fuses than specified on the unit data label. Failure to
follow this instruction may result in electrocution or
damage to the machine.

This unit is provided with an equipotential
grounding lug that is to be properly attached to the
rear of the frame by the authorized installer. The
installation location is marked by the equipotential
bonding symbol (5021 of IEC 60417-1) on both the
removable panel and the equipment's frame.

Stationary appliances which are not equipped with a
power cord and a plug or another device to
disconnect the appliance from the power source
must have an all-pole disconnecting device with a
contact gap of at least 3mm installed in the external
installation.

CAUTION: THIS EQUIPMENT MUST BE
PROPERLY GROUNDED! FAILURE TO DO SO
CAN RESULT IN SEVERE PERSONAL INJURY
FROM ELECTRICAL SHOCK!

FOLLOW YOUR LOCAL ELECTRICAL CODES!

Beater Rotation

Beater rotation must be clockwise as

viewed looking into the freezing cylinder.

The following repairs must be
performed by an authorized Taylor Service
Technician.

To correct rotation on a single-phase unit, change
the leads on the capacitor in the watt-control
electrical box. (See wiring diagram for details.)

Appliances that are permanently connected
to fixed wiring and for which leakage currents may
exceed 10 mA, particularly when disconnected or
not used for long periods, or during initial installation,
shall have protective devices such as a GFI, to
protect against the leakage of current, installed by
the authorized personnel to the local codes.

Supply cords used with this unit shall be
oil-resistant, sheathed flexible cable not lighter than
ordinary polychloroprene or other equivalent
synthetic elastomer-sheathed cord (Code
designation 60245 IEC 57) installed with the proper
cord anchorage to relieve conductors from strain,
including twisting, at the terminals and protect the
insulation of the conductors from abrasion.

To correct the rotation on a three-phase unit,
interchange any two incoming power supply lines at
the freezer main terminal block only.

Initial F reezing Cylinder Cleaning

Due to the types of products used in FCB
equipment, it is imperative that the freezing cylinder
and the inlet tube be thoroughly brush cleaned,
rinsed, and sanitized before running any product.

Prepare a cleaning solution, using 2 oz. of liquid
detergent in 2 gallons of warm water. Using this
solution, brush clean the freezing cylinder and the
inlet tube. Rinse the freezing cylinder and the inlet
tube with clean water. Sanitize, using the sanitizing
procedures outlined in this Operator Manual, starting
on page 25.

Models C303 & C314 To the Installer

3

Section 2 To the Operator

The freezer you have purchased has been carefully
engineered and manufactured to give you
dependable operation.

When properly operated and cared for, your freezer
will produce a consistent quality product. Like all
mechanical products, this machine will require
cleaning and scheduled maintenance. A minimum
amount of care and attention is necessary if the
operating procedures outlined in this manual are
followed closely.

This Operator's Manual should be read before
operating or performing any maintenance on your
equipment.

Your freezer will NOT eventually compensate and
correct for any errors during the set-up or filling
operations. Thus, the initial assembly and priming
procedures are of extreme importance. It is strongly
recommended that all personnel responsible for the
equipment's operation study these procedures
together in order to be properly trained and to make
sure that no misunderstandings exist.

In the event you should require technical assistance,
please contact your local authorized Taylor
Distributor for service.

Note: Warranty is valid only if the parts are
authorized Taylor parts, purchased from an
authorized Taylor Distributor, and the required
service work is provided by an authorized Taylor
service technician. Taylor reserves the right to deny
warranty claims on equipment or parts if
non-approved parts or refrigerant were installed in
the machine, system modifications were performed
beyond factory recommendations, or it is determined
that the failure was caused by neglect or abuse.

Note: Con st ant research result s in steady
improvements; therefore, information in this
manual is subject to change without notice.

If the crossed out wheeled bin symbol is
affixed to this product, it signifies that this product is
compliant with the EU Directive as well as other
similar legislation in effect after August 13, 2005.
Therefore, it must be collected separately after its

use is completed, and cannot be disposed as
unsorted municipal waste.

The user is responsible for returning the product to
the appropriate collection facility, as specified by
your local code.

For additional information regarding applicable local
laws, please contact the municipal facility and/or
local distributor.

Compressor Warranty Disclaimer

The refrigeration compressors on this machine are
warranted for the term indicated on the warranty
card accompanying this machine. However, due to
the Montreal Protocol and the U.S. Clean Air Act
Amendments of 1990, many new refrigerants are
being tested and developed, thus finding their way
into the service industry.

Some of these new refrigerants are being advertised
as “drop-in” replacements for numerous
applications. It should be noted that, in the event of
ordinary service to this machine’s refrigeration
system, only the refrigerant specified on the
affixed data label should be used. The
unauthorized use of alternate refrigerants will void
your compressor warranty. It will be the owner’s
responsibility to make this fact known to any
technician he employs.

It should also be noted that Taylor does not warrant
the refrigerant used in its equipment. For example, if
the refrigerant is lost during the course of ordinary
service to this machine, Taylor has no obligation to
either supply or provide its replacement either at
billable or unbillable terms. Taylor does have the
obligation to recommend a suitable replacement if
the original refrigerant is banned, obsoleted, or no
longer available during the five year warranty of the
compressor.

Taylor will continue to monitor the industry and test
new alternates as they are being developed. Should
a new alternate prove, through our testing, that it
would be accepted as a drop-in replacement, then
the above disclaimer would become null and void.

To find out the current status of an alternate
refrigerant as it relates to your compressor warranty,
call the local Taylor Distributor or the Taylor factory.
Be prepared to provide the Model/Serial Number of
the unit in question.

4

Models C303 & C314To the Operator

Section 3 Safety

We, at Taylor Company, are concerned about the
safety of the operator when he or she comes in
contact with the freezer and its parts. Taylor has
gone to extreme efforts to design and manufacture
built-in safety features to protect both you and the
service technician. As an example, warning labels
have been attached to the freezer to further point
out safety precautions to the operator.

IMPORTANT - Failure to adhere to the
following safety precautions may result in
severe personal injury or death. Failure to
comply with these warnings may damage the
machine and its components. Component
damage will result in part replacement expense
and service repair expense.

DO NOT attempt to run the equipment

unless you have been properly trained to do so.

must be disconnected prior to performing any
repairs. Failure to follow this instruction may result in
personal injury or death from electrical shock or
hazardous moving parts as well as poor
performance or damage to the equipment.

Note:Allrepairsmustbeperformedbyan
authorized Taylor Service Technician.

parts (example: freezer door, beater, scraper
blades, etc.) unless all control switches are in the
OFF position. Failure to follow this instruction may
result in severe personal injury from hazardous
moving parts.

The main power supply(s) to the freezer

DO NOT remove any internal operating

Do not operate this unit without reading
the Operator's Manual. Additional warning labels
have been attached to the unit to further point out
hygiene and safety precautions to the operator.

This equipment must be properly

grounded.

Do not operate this freezer unless it is properly
grounded and all service panels and access doors
are restrained with screws. Failure to do so can
result in severe personal injury from electrical shock.

This unit is provided with an equipotential
grounding lug that is to be properly attached to the
rear of the frame by the authorized installer. The
installation location is marked by the equipotential
bonding symbol (5021 of IEC 60417-1) on both the
removable panel and the equipment's frame.

This unit has many sharp edges that can

cause severe injuries.

S DO NOT put objects or fingers in the door

spout. This may contaminate the product
and cause severe personal injury from blade
contact.

S USE EXTREME CAUTION when removing

the beater asssembly. The scraper blades
are very sharp.

CAUTION: This unit is pressurized when

in operation. The control switch must be in the OFF

position until the unit is completely assembled. No
part should ever be removed from the machine while
it is in operation. No parts should be removed until
the control switch has been turned to the OFF
position and all pressure has been relieved by
opening the draw valve. Failure to follow this
instruction may result in severe personal injury from
hazardous moving parts or from the impact of
propelled parts.

Models C303 & C314 Safety

5

This unit must be installed on a level
surface to avoid the hazard of tipping. Extreme care
should be taken in moving this equipment for any
reason. Two or more persons are required to safely
move this unit. Failure to comply may result in
personnel injury or equipment damage.

This unit must NOT beinstalledinanarea
where a water jet or hose can be used. NEVER use
a water jet or hose to rinse or clean this unit. Using a
water jet or hose on or around this equipment may
result in electrocution to the user or damage to the
equipment.

Cleaning and sanitizing schedules are
governed by your state or local regulatory agencies
and must be followed accordingly. Please refer to
the cleaning section of this manual for the proper
procedure to clean this unit.

DO NOT obstruct air intake and discharge openings:
Air cooled units require a minimum of 3” (76 mm) of
air space on both sides, 3” (76 mm) at the rear, and
12” (305 mm) on the top of the unit. Minimum air
clearances must be met to assure adequate air flow
for optimum performance.

NOISE LEVEL: Airborne noise emission does not
exceed 78 dB(A) when measured at a distance of

1.0 meter from the surface of the machine and at a
height of 1.6 meters from the floor.

6

Models C303 & C314Safety

Section 4 Operator Parts Identification

Model C303

Figure 2

ITEM DESCRIPTION PART NO.

1 PANEL-SIDE-LEFT 059721
2 PANEL A.-REAR X66671
3 PANEL-SIDE-RIGHT 059722
4 DISPLAY-LED *C303 P.O.P. 066670
5 PANEL-FRONT-UPPER 066682
6 PANEL-FRONT-SHELL 066647

Models C303 & C314 Operator Parts Identification

ITEM DESCRIPTION PART NO.

7 PANEL-FRONT-LOWER 066678
8 SCREW-10-32 X 1/2 SLTD TRUS 037734

9 SHELF-DRIP TRAY 066677
10 TRAY-DRIP 066676
11 SHIELD-SPLASH 066680

7

Model C314

ITEM DESCRIPTION PART NO.

1 DISPLAY-LED-15.4"TALL 068575
2 PANEL-SIDE-LEFT 059721
3 PANEL A.-REAR X68182
4 SCREW-10-32X1/2 SLTD TRUS 037734
5 PANEL-FRONT-UPPER 068496
6 PANEL-FRONT-SHELL 059576

Figure 3

8

ITEM DESCRIPTION PART NO.

7 PANEL-FRONT-LOWER 059652

8 PANEL-SIDE-RIGHT 059722

9 SHELF-DRIP-TRAY 059653
10 TRAY-DRIP 059654
11 SHIELD-SPLASH 059659

Models C303 & C314Operator Parts Identification

Beater Door Assembly

ITEM DESCRIPTION PART NO.

1 DOOR A.-SLUSH PRESS. X39572-BLA
1a CAP-SPOUT-DOOR-FCB-BLK 046191-BLA
1b SPRING-COMP.480X.072X3.0 039320
1c VALVE-DRAW-DOOR-PRESS. 039324
1d O-RING-9/16 OD X .103W 016369
1e SPOUT-DOOR-FCB-BLACK 046190-BLA
1f HANDLE-DRAW-FCB-BLACK 046192-BLA
1g PIN-PIVOT-SPOUT-DOOR 039321
1h SLIDE-HANDLE-DOOR-BLK 046193-BLA
1i SCREW-10-32X3/8PHL 053869
1j O-RING-9/32 OD X 1/16 WALL 029751
1k PLUG-PRIME-SLUSH-PRESS. 039568

Figure 4

ITEM DESCRIPTION PART NO.

1l DOOR-FREEZER-SLUSH-PRES 039573
1m O-RING-1.129 ODX.989ID 039219
1n NUT-SPOUT-DOOR-PRESS. 039323
1o O-RING-5-1/4ODX.210W DOOR 017003
2 NUT-STUD 043666
3 BEARING-FRONT-PRESSURE 039349
4 BEATER-PLASTIC-FCB-PRESS. 041182
5 BLADE-SCRAPER-FCB-16INCH 041103
6 SHAFT-BEATER-SLUSH-PRES 066679
7 BUSHING-BEATER

SHAFT/BOOT SEAL

8 SEAL-DRIVE SHAFT 032560

042278

Models C303 & C314 Operator Parts Identification

9

Accessories

ITEM DESCRIPTION PART NO.

1 PAIL-MIX 10 QT 013163
2 BRUSH A. (INCLUDES 2a-2d) X64275
2a BRUSH-MIX PUMP BODY-3”X7” 023316
2b BRUSH-DOUBLE ENDED 013072
2c BRUSH-REAR BRG 1”DX2“L 013071

Figure 5

10

ITEM DESCRIPTION PART NO.

2d BRUSH-DRAW VALVE 1-1/2”OD 014753
3 KIT A.-TUNE UP X59121
4 LUBRICANT-TAYLOR HI PERF 048232
5 SANITIZER-STERA SHEEN SEE NOTE

*Note: A sample container of sanitizeris sent with the
unit. For reorders, order SteraSheen partno. 055492
(100 packs) or Kay-5 partno. 041082 (125 packs).

Models C303 & C314Operator Parts Identification

Section 5 Important: To the Operator

ITEM DESCRIPTION

1 CONTROL SWITCH
2 LIQUID CRYSTAL DISPLAY
3 KEYPADS
4 PRODUCT LIGHT

To identify the freezing cylinders in these units, the
barrels are referred to as follows:

Starting from left to right: barrel 1, barrel 2, barrel 3,
and for the C314 only, barrel 4.

Control Switch

The control switch(s) is located at the top left corner
of the upper front panel, behind the illuminated
display. When placed in the ON position, this control
switch allows machine operation.

Figure 6

Liquid Crystal Display

There is one Liquid Crystal Display (LCD) located on
the upper front panel behind the illuminated display.
The LCD displays information for the freezing
cylinders located directly beneath it.

The LCD shows the current operating mode of the
freezing cylinders. It also indicates whether there is
enough syrup, CO2, and water being supplied to the
freezer. If an error in the machine operation occurs,
a warning tone will sound and the word “FAULT” will
flash on the third line of the display.

Models C303 & C314 Important: To the Operator

11

Operational Mode Displays

Line 1 indicates the operating mode for each
freezing cylinder.

The screens illustrated in this section are those seen
on the Model C303. (The Model C314 screens vary
slightly to include the fourth barrel information.)

These screens illustrate the operational mode
information displayed during normal operation. The
LCD displays information corresponding to the
freezing cylinders located directly beneath them.

When the unit is plugged into the wall receptacle
and the control switch is in the ON position, the
following screen appears.

SAFETY TIMEOUT

ANY KEY ABORT

The display will remain on the LCD for 60 seconds
unless a key is pressed. If any key is pressed (or 60
seconds passes) the following screen appears.

OFF OFF OFF
OK OK OK

CO2-OK WATER-OK

Note: Syrup, CO2and water are satisfied.

Pressing the A UTO (- ->) keys for each freezing
cylinder will display the following screen.

Line 2 indicates the status of the syrup systems in
each freezing cylinder. As long as syrup is available,
the word “OK” will appear on the LCD. When the
syrup supply is insufficient, the word “OUT” will flash
on the LCD. The same rules apply to the fourth line
which indicates the status of the CO

and the H2O.

2

The third line of this display is a fault indicator. If an
error in machine operation occurs, the word “FAULT
will be displayed on the LCD. See the example
screen below.

BEATER BEATER BEATER
OUT OUT OUT

- -FAULT- -

CO2-OUT H2O-OUT

Operator Menu Display

The OPERATOR MENU is used to enter the
operating screens. To access the OPERATOR
MENU, press the MENU (SEL) key. The cursor will
flash under the letter “A”, indicating that this is
screen A. To select a different screen, use the
AUTO (- ->) and OFF (<- -) keys to move the cursor
to the desired screen selection and press the MENU
(SEL) key.

AUTO AUTO AUTO
OK OK OK

CO2-OK WATER-OK

12

OPERATOR MENU

B C D E F G H I

A

EXIT MENU
<- - - -> SEL

Models C303 & C314Important: To the Operator

Operator Menu Timeout

If the display is left in the operator menu or in any of
the operator menu selections except “Current
Conditions”, the display will return to the system
mode screen 60 seconds after the last key press.
The Current Conditions screen will be displayed until
manually changed.

Finding Current Fault Conditions

Screen B is FAULT DESCRIPTION. The fault

description screen will indicate if there is a fault in
one of the freezing cylinders. Upon correction of the
fault, the warning tone will stop.

Note: “BRL NOT COOLING” is the only fault that
requires pressing the OFF (<- -) key t o clear the
fault message and the warning tone.

The following are explanations of possible faults and
the display screens. Pressing the +++ key shows
the faults for each freezing cylinder. The freezing
cylinders are referred to as barrel 1 (left barrel),
barrel 2 (center barrel), and barrel 3 (right barrel).

1. NO FAULT FOUND - No fault conditions are
apparent.

FAULT DESCRIPTION
BARREL 1
NO FAULT FOUND
CLR + + + SEL

2. BEATER OVERLOAD - Beater motor is out on
overload. When this fault occurs, the affected
barrel automatically turns off. The fault clears
when the condition is corrected.

FAULT DESCRIPTION
BARREL 1
BEATER OVERLOAD
CLR + + + SEL

3. CHK REFRIG SYS PSI - The compressor is
out on high head pressure. When this fault
occurs, the machine automatically turns off.
The fault clears when the condition is corrected.

Fault Messages

Beater Overload Beater is out on overload.
Chk Refrig Sys Psi Out on compressor high

pressure cut-out.
Thermistor Short Shorted thermistor probe.
Thermistor Open Open thermistor probe.
H2O Pressure Low Water pressure is low.
CO2 Pressure Low CO2pressure is low.
Syrup Pressure Low Syrup is no longer present.
BRLTemp2High Freezing cylinder

temperature is above 120_F

(49_C).
BRL Not Cooling Freezing cylinder is not

cooling after 5 minutes.
No Fault Found No fault conditions are

apparent.

FAULT DESCRIPTION
BARREL 1
CHK REFRIG SYS PSI
CLR + + + SEL

4. THERMISTOR SHORT - One of the barrel
(freezing cylinder) thermistor probes is faulty.

FAULT DESCRIPTION
BARREL 1
THERMISTOR SHORT
CLR + + + SEL

5. THERMISTOR OPEN - One of the barrel
(freezing cylinder) thermistor probes is faulty.

FAULT DESCRIPTION
BARREL 1
THERMISTOR OPEN
CLR + + + SEL

Models C303 & C314 Important: To the Operator

13