Taylor Freezer 8752, 8756, 8757 Operation Manual
Models 8752, 8756, 8757
Soft Serve Freezers
Operating Instructions
028752-M
8/99 (Original Publication)
(Updated 11/10)
Complete this page for quick reference when service is required:
Taylor Distributor:
Address:
Phone:
Service:
Parts:
Date of Installation:
Information found on the data label:
Model Number:
Serial Number:
Electrical Specs: Voltage Cycle
Phase
Maximum Fuse Size: Amps
Minimum Wire Ampacity: Amps
Part Number:
E August, 1999 Taylor (Original Publication)
(Updated November, 2010)
All rights reserved.
028752--M
The word Taylor and the Crown design
are registered trademarks in the United States
of America and certain other countries.
Taylor Company
750 N. Blackhawk Blvd.
Rockton, IL 61072
Table of Contents
Section 1 To the Installer 1............................................
Section 2 To the Operator 4...........................................
Compressor Warranty Disclaimer 4.......................................
Section 3 Safety 5....................................................
Section 4 Operator Parts Id en t ificatio n 7...............................
Model 8752 7..........................................................
8752 Beater Door Assembly 9............................................
Model 8756 11..........................................................
Model 8757 13..........................................................
8756 & 8757 Beater Door Assembly 15.....................................
Accessories 16..........................................................
Section 5 Important: To the Operator 17.................................
Symbol Definitions 18....................................................
Power Switch 18.........................................................
Indicator Lights -- MIX LOW and MIX OUT 18................................
Reset Button 18.........................................................
SOFTECH Control Operation 18...........................................
MIX REF 18.............................................................
Standby 19..............................................................
Wash 19................................................................
Auto 19.................................................................
Pump 19................................................................
Adjustable Draw Handle 19...............................................
Section 6 Operating Procedures 20.....................................
Prior to Set--Up (Model 8757) 20...........................................
Assembly 20............................................................
Air/Mix Pump Assembly 24................................................
Models 8752, 8756, & 8757 Table of Contents
Table of Contents -- Page 2
Air/Mix Pump Assembly Exploded View 28..................................
Sanitizing 29............................................................
Priming 31..............................................................
Closing Procedure 32....................................................
Draining Product From the Freezing Cylinder 32.............................
Rinsing 33..............................................................
Cleaning 33.............................................................
Disassembly 34..........................................................
Brush Cleaning 34.......................................................
Check Topping Pump Temperature and Volume -- Model 8757 35..............
Section 7 Important: Operator Checklist 36..............................
During Cleaning and Sanitizing 36.........................................
Troubleshooting Bacterial Count 36........................................
Regular Maintenance Checks 36...........................................
The Air/Mix Pump 37.....................................................
Winter Storage 37........................................................
Section 8 Troubleshooting Guide 38....................................
Section 9 Parts Replacement Schedule 43...............................
Section 10 Parts List 44.................................................
Wiring Diagrams 56......................................................
E August, 1999 Taylor (Original Publication)
(Updated November, 2010)
All rights reserved.
028752--M
The word Taylor and the Crown design
are registered trademarks in the United States
of America and certain other countries.
Table of Contents Models 8752, 8756, & 8757
Taylor Company
750 N. Blackhawk Blvd.
Rockton, IL 61072
Section 1 To the Installer
The following are general installation instructions. For
complete installation details, please see the check out
card.
Installer Safety
In all areas of the world, equipment should be
installed in accordance with existing local codes.
Please contact your local authorities if you have any
questions.
Care should be taken to ensure that all basic safety
practices are followed during the installation and
servicing activities related to the installation and
service of Taylor equipment.
S Only authorized Taylor service personnel
should perform installation and repairs on
the equipment.
S Authorized service personnel should consult
OSHA Standard 29CFRI910.147 or the
applicable code of the local area for the
industry standards on lockout/tagout
procedures before beginning any installation
or repairs.
S Authorized service personnel must ensure
that the proper PPE is available and worn
when required during installation and
service.
S Authorized service personnel must remove
all metal jewelry, rings, and watches before
working on electrical equipment.
Site Preparation
Review the area the unit is to be installed in before
uncrating the unit making sure that all possible
hazards the user or equipment may come into have
been addressed.
Air Cooled Units
DO NOT obstruct air intake and discharge openings:
Air cooled units require a minimum of 3” (76 mm) of
clearance around all sides of the freezer and 12” (305
mm) on top to allow for adequate air flow across the
condenser(s). Failure to allow adequate clearance can
reduce the refrigeration capacity of the freezer and
possibly cause permanent damage to the compressor.
For Indoor Use Only: This unit is designed to operate
indoors, under normal ambient temperatures of
70_-75_F(21_-24_C). The freezer has successfully
performed in high ambient temperatures of
104_(40_C) at reduced capacities.
This unit must NOT be installed in an area
where a water jet or hose can be used. NEVER use a
water jet or hose to rinse or clean the unit. Failure to
follow this instruction may result in electrocution.
The main power supply(s) to the freezer must
be disconnected prior to performing any repairs.
Failure to follow this instruction may result in personal
injury or death from electrical shock or hazardous
moving parts as well as poor performance or damage
to the equipment.
Note:Allrepairsmustbeperformedbyan
authorized Taylor Service Technician.
This unit has many sharp edges that can
cause severe injuries.
Models 8752, 8756, 8757 To the Installer
to avoid the hazard of tipping. Extreme care should be
taken in moving this equipment for any reason. Two or
more persons are required to safely move this unit.
Failure to comply may result in personal injury or
equipment damage.
Uncrate the unit and inspect it for damage. Report any
damage to your Taylor Distributor.
This piece of equipment is made in the USA and has
USA sizes of hardware. All metric conversions are
approximate and vary in size.
1
This unit must be installed on a level surface
081208
Water Connections
(Water Cooled Units Only)
An adequate cold water supply must be provided with
a hand shut--off valve. On the underside rear of the
base pan, two 3/8” I.P.S. (for single--head units) or two
1/2” I.P.S. (for double--head units) water connections
for inlet and outlet have been provided for easy
hook--up. 1/2” inside diameter water lines should be
connected to the machine. (Flexible lines are
recommended, if local codes permit.) Depending on
local water conditions, it may be advisable to install a
water strainer to prevent foreign substances from
clogging the automatic water valve. There will be only
one water “in” and one water “out” connection for both
single--head and double--head units. DO NOT install a
hand shut--off valve on the water “out” line! Water
should always flow in this order: first, through the
automatic water valve; second, through the
condenser; and third, through the outlet fitting to an
opentrapdrain.
A back flow prevention device is required
on the incoming water connection side. Please
refer to the applicable National, State, and local codes
for determining the proper configuration.
Each unit requires one power supply for each data
label on the unit. Check the data label(s) on the freezer
for branch circuit overcurrent protection or fuse, circuit
ampacity and other electrical specifications. Refer to
the wiring diagram provided inside of the electrical box,
for proper power connections.
CAUTION: THIS EQUIPMENT MUST BE
PROPERLY GROUNDED! FAILURE TO DO SO
CAN RESULT IN SEVERE PERSONAL INJURY
FROM ELECTRICAL SHOCK!
DO NOT operate this freezer with larger fuses
than specified on the unit data label. Failure to follow
this instruction may result in electrocution or damage
to the machine.
This unit is provided with an equipotential
grounding lug that is to be properly attached to the rear
of the frame by the authorized installer. The installation
location is marked by the equipotential bonding
symbol (5021 of IEC 60417-1) on both the removable
panel and the equipments frame.
Electrical Connections
In the United States, this equipment is intended to be
installed in accordance with the National Electrical
Code (NEC), ANSI/NFPA70-1987. The purpose of the
NEC code is the practical safeguarding of persons and
property from hazards arising from the use of
electricity. This code contains provisions considered
necessary for safety. In all other areas of the world,
equipment should be installed in accordance with the
existing local codes. Please contact your local
authorities.
FOLLOW YOUR LOCAL ELECTRICAL CODES!
Stationary appliances which are not equipped
with a power cord and a plug or another device to
disconnect the appliance from the power source must
have an all-pole disconnecting device with a contact
gap of at least 3mm installed in the external
installation.
Appliances that are permanently connected to
fixed wiring and for which leakage currents may
exceed 10 mA, particularly when disconnected or not
used for long periods, or during initial installation, shall
have protective devices such as a GFI, to protect
against the leakage of current, installed by the
authorized personnel to the local codes.
101122
2
Models 8752, 8756, 8757To th e Installer
Supply cords used with this unit shall be
oil-resistant, sheathed flexible cable not lighter than
ordinary polychloroprene or other equivalent synthetic
elastomer-sheathed cord (Code designation 60245
IEC 57) installed with the proper cord anchorage to
relieve conductors from strain, including twisting, at
the terminals and protect the insulation of the
conductors from abrasion.
Beater Rotation
Beater rotation must be clockwise as viewed
looking into the freezing cylinder.
Note: The following procedures should be
performed by a trained service technician.
To correct the rotation on a three--phase unit,
interchange any two incoming power supply lines at
freezer main terminal block only.
To correct rotation on a single--phase unit, change the
leads inside the beater motor. (Follow the diagram
printedonthemotor.)
Refrigerant
In consideration of our environment, Taylor
proudly uses only earth friendly HFC refrigerants. The
HFC refrigerant used in this unit is R404A. This
refrigerant is generally considered non-toxic and
non-flammable, with an Ozone Depleting Potential
(ODP) of zero (0).
However, any gas under pressure is potentially
hazardous and must be handled with caution.
NEVER fill any refrigerant cylinder completely with
liquid. Filling the cylinder to approximately 80% will
allow for normal expansion.
Refrigerant liquid sprayed onto the skin may
cause serious damage to tissue. Keep eyes and skin
protected. If refrigerant burns should occur, flush
immediately with cold water. If burns are severe, apply
ice packs and contact a physician immediately.
Taylor reminds technicians to be cautious of
government laws regarding refrigerant recovery,
recycling, and reclaiming systems. If you have any
questions regarding these laws, please contact the
factory Service Department.
Electrical connections are made directly to the
terminal block provided in the splice box which is
mounted on the base pan on the right side of the
freezer for the Model 8752 and located in the splice
boxes which are mounted mid--level on the frame
channel on the right and left sides for the Models 8756
and 8757.
WARNING: R404A refrigerant used in
conjunction with polyolester oils is extremely moisture
absorbent. When opening a refrigeration system, the
maximum time the system is open must not exceed 15
minutes. Cap all open tubing to prevent humid air or
water from being absorbed by the oil.
080815
Models 8752, 8756, 8757 To the Installer
3
Section 2 To the Operator
The freezer you have purchased has been carefully
engineered and manufactured to give you dependable
operation. The Taylor Models 8752, 8756, and 8757
are highly sophisticated pieces of equipment, and
when properly operated and cared for, will produce a
consistent quality product. Like all mechanical
products, they will require cleaning and maintenance.
A minimum amount of care and attention is necessary
if the operating procedures outlined in this manual are
followed closely.
This Operator’s Manual should be read before
operating or performing any maintenance on your
equipment.
Your freezer will NOT eventually compensate and
correct for any errors during the set--up or filling
operations. Thus, the initial assembly and priming
procedures are of extreme importance. It is strongly
recommended that all personnel responsible for the
equipment’s operation study these procedures
together in order to be properly trained and to make
sure that no misunderstandings exist.
In the event you should require technical assistance,
please contact your local authorized Taylor Distributor.
Note: Warranty is valid only if the parts are authorized
Taylor parts, purchased from an authorized Taylor
Distributor, and the required service work is provided
by an authorized Taylor service technician. Taylor
reserves the right to deny warranty claims on
equipment or parts if non--approved parts or
refrigerant were installed in the machine, system
modifications were performed beyond factory
recommendations, or it is determined that the failure
was caused by neglect or abuse.
Note: Constant research results in steady
improvements; therefore, information in this
manual is subject to change without notice.
If the crossed out wheeled bin symbol is
affixed to this product, it signifies that this product is
compliant with the EU Directive as well as other similar
legislation in effect after August 13, 2005. Therefore,
it must be collected separately after its use is
completed, and cannot be disposed as unsorted
municipal waste.
The user is responsible for returning the product to the
appropriate collection facility, as specified by your local
code.
For additional information regarding applicable local
laws, please contact the municipal facility and/or local
distributor.
Compressor Warranty Disclaimer
The refrigeration compressor(s) on this machine are
warranted for the term indicated on the warranty card
accompanying this machine. However, due to the
Montreal Protocol and the U.S. Clean Air Act
Amendments of 1990, many new refrigerants are
being tested and developed, thus seeking their way
into the service industry. Some of these new
refrigerants are being advertised as drop--in
replacements for numerous applications. It should be
noted that, in the event of ordinary service to this
machine’s refrigeration system, only the refrigerant
specified on the affixed data label should be used.
The unauthorized use of alternate refrigerants will void
your compressor warranty. It will be the owner’s
responsibility to make this fact known to any technician
he employs.
It should also be noted that Taylor does not warrant the
refrigerant used in its equipment. For example, if the
refrigerant is lost during the course of ordinary service
to this machine, Taylor has no obligation to either
supply or provide its replacement either at billable or
unbillable terms. Taylor does have the obligation to
recommend a suitable replacement if the original
refrigerant is banned, obsoleted, or no longer available
during the five year warranty of the compressor.
The Taylor Company will continue to monitor the
industry and test new alternates as they are being
developed. Should a new alternate prove, through our
testing, that it would be accepted as a drop--in
replacement, then the above disclaimer would
become null and void. To find out the current status of
an alternate refrigerant as it relates to your
compressor warranty, call the local Taylor Distributor
or the Taylor Factory . Be prepared to provide the
Model/Serial Number of the unit in question.
080815
4
Models 8752, 8756, 8757To th e Operator
Section 3 Safety
We at Taylor Company are concerned about the safety
of the operator when he or she comes in contact with
the freezer and its parts. Taylor has gone to extreme
efforts to design and manufacture built--in safety
features to protect both you and the service technician.
As an example, warning labels have been attached to
the freezer to further point out safety precautions to the
operator.
IMPORTANT -- Failure to adhere to the
following safety precautions may result in severe
personal injury or death. Failure to comply with
these warnings may damage the machine and its
components. Component damage will result in
part replacement expense and service repair
expense.
DO NOT operate the freezer without reading
this Operator Manual. Failure to follow this instruction
may result in equipment damage, poor freezer
performance, health hazards, or personal injury.
This unit is provided with an equipotential
grounding lug that is to be properly attached to the rear
of the frame by the authorized installer. The installation
location is marked by the equipotential bonding
symbol (5021 of IEC 60417-1) on both the removable
panel and the equipments frame.
DO NOT use a water jet to clean or rinse the
freezer. Failure to follow these instructions may result
in serious electrical shock.
S DO NOT operate the freezer unless it is
properly grounded.
S DO NOT operate the freezer with larger
fuses than specified on the freezer data
label.
S DO NOT attempt any repairs unless the
main power supply to the freezer has been
disconnected.
S Stationary appliances which are not
equipped with a power cord and a plug or
another device to disconnect the appliance
from the power source must have an all-pole
disconnecting device with a contact gap of
at least 3mm installed in the external
installation.
S Appliances that are permanently connected
to fixed wiring and for which leakage
currents may exceed 10 mA, particularly
when disconnected or not used for long
periods, or during initial installation, shall
have protective devices such as a GFI, to
protect against the leakage of current,
installed by the authorized personnel to the
local codes.
S Supply cords used with this unit shall be
oil-resistant, sheathed flexible cable not
lighter than ordinary polychloroprene or
other equivalent synthetic
elastomer-sheathed cord (Code designation
60245 IEC 57) installed with the proper cord
anchorage to relieve conductors from strain,
including twisting, at the terminals and
protect the insulation of the conductors from
abrasion.
Failure to follow these instructions may result in
electrocution. Contact your local authorized Taylor
Distributor for service.
080820
Models 8752, 8756, 8757 Safety
5
S DO NOT allow untrained personnel to
operate this machine.
S DO NOT operate the freezer unless all
service panels and access doors are
restrained with screws.
S DO NOT remove any internal operating
parts (example: freezer door, beater,
scraper blades, etc.) unless all control
switches are in the OFF position.
Failure to follow these instructions may result in severe
personal injury from hazardous moving parts.
This unit has many sharp edges that can
cause severe injuries.
S DO NOT put objects or fingers in the door
spout. This may contaminate the product
and cause severe personal injury from blade
contact.
S USE EXTREME CAUTION when removing
the beater asssembly. The scraper blades
are very sharp.
Cleaning and sanitizing schedules are
governed by your state or local regulatory agencies
and must be followed accordingly. Please refer to the
cleaning section of this manual for the proper
procedure to clean this unit.
DO NOT obstruct air intake and discharge openings:
Air cooled units require a minimum of 3” (76 mm) of
clearance around all sides of the freezer and 12” (305
mm) on top to allow for adequate air flow across the
condenser(s). Failure to allow adequate clearance can
reduce the refrigeration capacity of the freezer and
possibly cause permanent damage to the compressor.
For Indoor Use Only: This unit is designed to operate
indoors, under normal ambient temperatures of 70_ -
75_F(21_ -24_C). The freezer has successfully
performed in high ambient temperatures of
104_(40_C) at reduced capacities.
This freezer must be placed on a level
surface. Failure to comply may result in personal injury
or equipment damage.
NOISE LEVEL: Airborne noise emission does not
exceed 78 dB(A) when measured at a distance of 1.0
meter from the surface of the machine and at a height
of 1.6 meters from the floor.
080826
6
Models 8752, 8756, 8757Safety
Section 4 Operator Parts Identification
Model 8752
Models 8752, 8756, 8757 Operator Parts Identification
7
8752 Parts Identification
Item Description Part No.
1 Panel A.--Front X22997
2 Stud-- Nose Cone 022822
3 Bolt-- Carriage 012347
4 Panel A.--Lower Side (R & L) X23956
5 Panel-- Upper Side Left 028599
6 Hood 050464
7 Panel-- Upper Rear 022074
8 Panel-- Lower Rear 025128
9 Panel-- Upper Side Right 028600
10 Pan--Drip 11 --5/8” Long 027503
11 Caster--Swivel 3/4--10, 3” Wheel 021279
12 Gasket--Cabinet Mix Door 020134
13 Probe A.--Mix X35981
14 Boot--Mix Cover 037200
Item Description Part No.
15 Tank--Mix 020275
16 Cover A.-- Mix Tank X38726
17 Funnel-- Mix 036637
18 Tray--Drip 16--7/8 x 5--1/8 020157
19 Shield--Splash 23” Long 022765
20 Cover--Mix Storage--Center
Single
21 Trim--Rear Corner 022071
22 Trim A.-- Upper Side Left/Right X22423
23 Trim A.-- Shelf X20426
24 Trim--Front--Left 024824 --SP
25 Trim--Front--Right 024825
26 Trim--Bottom Mix Door 024974
27 Trim--Mix Door 024976
038827
8
Models 8752, 8756, 8757Operator Parts Identification
8752 Beater Door Assembly
Models 8752, 8756, 8757 Operator Parts Identification
9
8752 Beater Door Parts Identification
Item Description Part No.
1 Seal-- Drive Shaft 032560
2 Shaft--Beater 032564
3 Beater A.-- 3.4 Qt. 1 Pin X46231
4 Clip--Scraper Blade 046236
5 Blade-- Scraper--Plastic 046235
*6a Bearing--Front 050348
*6b Shoe-- Front Helix--Front 050347
*6c Shoe-- Front Helix--Rear 050346
7 Gasket-- Door HT 4” Double 048926
8 Door A.--1 Spout Long Baffle X51531--10
9 Handle A.--Draw--Adj. X26996
9a Draw Handle --Adj. 028804
Item Description Part No.
9b Screw--Adjustment 026592
9c O--Ring (Adj. Screw) 015872
9d Nut--Jam 5/16--24 029639--BLK
10 O--Ring -- 5/16 OD x .070 W 016272
11 Pin A.--Pivot X22820
12 Nut-- Stud 021508
13 Val ve A .- -Dr aw X18303
14 O-- Ring -- 7/8 OD x .103 W 014402
15 Cap--Design -- 1.010” ID 014218
16 Plug-- Prime 028805
17 O-- Ring -- 3/8 OD x .070 W 016137
*Order as X50350 only.
10
Models 8752, 8756, 8757Operator Parts Identification
Model 8756
Models 8752, 8756, 8757 Operator Parts Identification
11
8756 Parts Identification
Item Description Part No.
1 Panel A.--Front X22879
2 Stud-- Nose Cone 022822
3 Bolt-- Carriage 012347
4 Panel A.--Lower Side (R & L) X23956
5 Panel-- Upper Side Left 028599
6 Hood 048526
7 Panel-- Upper Rear 022015
8 Panel-- Lower Rear 023598
9 Panel-- Upper Side Right 028600
10 Pan-- Drip 17--1/4” Long 027504
11 Caster--Swivel 3/4--10, 3” Wheel 021279
12 Gasket--Cabinet Mix Door 024629
13 Probe A.--Mix (2) X35981
14 Boot--Mix Cover 037200
15 Tank A.-- Mix w/Decals X38755
Item Description Part No.
15a Tank (only) 034928
16 Cover--Mix Tank 024590
17 Funnel--Mix 036637
18 Tray-- Drip 22--7/8 x 5-- 1/8 014533
19 Shield--Splash 23” Long 022766
20 Cover--Left Mix Storage 037138
21 Cover--Right Mix Storage 037139
22 Tr im-- Corner--Left/Right 022013
23 Trim A.--Side Left/Right X22424
24 Trim A.-- Shelf X24813
25 Trim--Front--Left 024824--SP
26 Trim--Front--Right 024825
27 Trim--Bottom Cabinet 024826
28 Strip-- Top Trim 024827
12
Models 8752, 8756, 8757Operator Parts Identification
Model 8757
Models 8752, 8756, 8757 Operator Parts Identification
13
8757 Parts Identification
Item Description Part No.
1 Panel A.-- Front X36711
2 Stud--Nose Cone 022822
3 Bolt--Carriage 1/4--20 x 3/4 012347
4 Panel A.-- Lower Side--L/R X36741
5 Panel--Upper Side Left 028599
6 Hood 048526
7 Panel--Upper Rear 042068
8 Panel--Lower Rear 042067
9 Panel--Upper Side Right 028600
10 Pan-- Drip 036232
11 Caster--Swivel 3/4-- 10 ST 021279
12 Gasket--Cabinet--Mix Door 024629
13 Probe A.-- Mix X35981
14 Boot--Mix Cover 037200
15 Tank--Mix X38755
Item Description Part No.
15a Tank (only) 034928
16 Cover--Mix Tank 024590
17 Funnel--Mix 036637
18 Tray-- Drip 014533
19 Shield--Splash 23” Long 022766
20 Cover--Mix Storage Left 037138
21 Cover--Mix Storage Right 037139
22 Trim--Rear Corner-- Left/Right 036740
23 Trim A.-- Side Left/Right X22424
24 Trim A.--Shelf X36732
25 Trim-- Front-- Left 024824--SP
26 Trim-- Front--Right 024825
27 Trim-- Bottom Cabinet 024826
28 Strip--Top Trim 024827
14
Models 8752, 8756, 8757Operator Parts Identification
8756 & 8757 Beater Door Assembly
Item Description Part No.
1 Seal-- Drive Shaft 032560
2 Shaft--Beater 032564
3 Beater A.-- 3.4 Qt. 1 Pin X46231
4 Clip--Scraper Blade 046236
5 Blade-- Scraper--Plastic 046235
*6a Bearing--Front 050348
*6b Shoe-- Front Helix--Rear 050346
*6c Shoe-- Front Helix--Front 050347
7 Gasket-- Door 4” Double 048926
8 Door A.--3 Spout Long Baffle X51532--12
9 Handle A.--Draw--Adj. X33687
9a Draw Handle --Adj. 028804
9b Screw--Adjustment 033662
Models 8752, 8756, 8757 Operator Parts Identification
Item Description Part No.
9c O--Ring (Adj. Screw) 015872
9d Nut--Jam 5/16--24 029639--BLK
10 O--Ring -- 5/16 OD x .070 W 016272
11 Rod A.--Pivot X22387
12 Nut-- Stud (Long) 034382
13 Val ve A .- -Dr aw (3) X18303
14 O-- Ring -- 7/8 OD x .103 W (6) 014402
15 Cap--Design -- 1.010” ID 014218
16 Nut--Stud (Short) 034383
17 Rod A.--Pivot X22388
18 Plug-- Prime (2) 028805
19 O-- Ring -- 3/8 OD x .070 W (4) 016137
*Order Kit X50350
15
Accessories
L
U
B
E
0
4
8
2
6
0
3
10
0
4
8
2
6
0
1
2
9
11
4
5
6
Item Description Part No.
1 Brush-- Mix Pump Body 023316
2 Brush--Pressure Switch 027647
3 Brush--Feed Tube 021101
4 Brush--Double Ended 013072
5 Brush--Rear Bearing 013071
6 Brush--Draw Valve 013073
7 Lubricant-- Taylor 4 oz. 047518
SS
TERA HEEN
GREEN LABEL
SANITIZER & CLEANER
(MILKSTONE REMOVER)
KAY-5
Sanitizer/Cleaner
CAUTION
FORINSTITUTIONAL USE ONLY
1OZ(28.4g)
®
8
R
7
KEEPOUT OF REACH OF CHILDREN
Item Description Part No.
8 Sanitizer--Kay --5 (8752, 8757) 041082
9 Pail--Mix 10 Qt. 013163
Kit A.-- Tune Up (Model 8752) X49463--15
10
Kit A.--Tune Up
(Models 8756 & 8757)
11 Sanitizer-- Stera Sheen --Green
X49463--2
065293
(8756)
071017
16
Models 8752, 8756, 8757Operator Parts Identification
Section 5 Important: To the Operator
Model 8752
Model 8756
Model 8757
Models 8752, 8756, 8757 Important: To the Operator
17
Loading...