Taylor Freezer 220 General Manual
Item No. _______________________________
220
Batch Ice Cream Freezer
Features
Serve homemade, high overrun ice cream, sorbet or Italian
ice. Fruits, candies and nuts can be folded in as product is
being drawn into your container.
Freezing Cylinder
One, 20 quart (18.9 liter).
Mix Hopper
One, 10 quart (9.5 liter). Mix flows into the freezing cylinder through
an opening in the hopper mounted funnel. With the funnel closed,
more mix can be added to the hopper in preparation for the next
batch.
Automatic Temperature Control
Refrigeration system shuts off when set temperature is reached. A
buzzer will sound to remind the operator to eject the finished
product into tubs or other containers.
Adjustable Shelf
Three positions for filling large to small containers.
Rockton, Illinois 61072
800-255-0626
Phone 815-624-8333 Fax 815-624-8000
www.taylor-company.com
e-mail: info@taylor-company.com
220
International Office
Taylor Company S.r.l.
Roma, Italy
Tel: +39-06-420-12002 Fax: +39-06-420-12034
e-mail: romeoff@taylor-company.com
220Batch Ice Cream Freezer
FAUCET
COUPLINGS (2)
1-1/16 (2.7) DIA
ELECTRICAL HOLE
FAUCET
COUPLINGS (2)
WATER OUT
1-1/2
(38)
20-1/2
(521)
1-1/16 (27) DIA
ELECTRICAL HOLE
WATER IN
4
(102)
18-7/16
(468)
4-7/8
(13)
5-3/4
(146)
3-3/4
(95)
1-1/4
(32)
5-3/4
(146)
3-3/4
(95)
1-1/4
(32)
1-1/2
(38)
14-3/4
(375)
1-1/2
(38)
14-3/4
(375)
FIGURES IN PARENTHESES INDICATE MILLIMETERS.
17-1/2
(445)
TOP VIEW BASE - OPERATOR END
WATER COOLED
AIR COOLED
17-1/2
(445)
1-1/2
(38)
40-1/2
(1029)
15-3/4
(40)
4-1/2
(115)
AIR IN
RESET BUTTON
56-1/2
(1435)
AIR IN
32-3/8
(823)
6-3/8
(162)
11
(280)
14-3/4
(375)
13-1/2
(343)
5
(127)
36
(915)
9-1/4
(235)
1-9/16 (40)
4-1/4
(108)
AIR OUT
(AIR COOLED ONLY)
220
Weights lbs. kgs.
Net 500 226.8
Crated 598 271.3
cu. ft. cu. m.
Volume 59.9 1.69
Dimensions in. mm.
Width 18-7/16 468
Depth 40-1/2 1029
Height 56-1/2 1435
Floor Clearance 4-1/4 108
*Mounted on standard casters
Electrical Maximum Minimum Poles (P)
Fuse Size Circuit Ampacity Wires (W)
208-230/60/1 Air 50 35 2P 3W
208-230/60/1 Water 50 33 2P 3W
208-230/60/3 Air 30 23 3P 4W
208-230/60/3 Water 30 20 3P 4W
220-240/50/1 Air 30 24 2P 3W
380-415/50/3N~ Air 15 12 4P 5W
This unit may be manufactured in other electrical and cooling characteristics.
Refer to the local Taylor Distributor for availability.
(For exact electrical information, always refer to the data label of the unit.)
Bidding Specs
Electrical: Volt ___________________ Hz__________ ph _________
Options:_________________________________________________
_________________________________________________________
Neutral: Yes No Cooling: Air Water NA
Specifications
Electrical
One dedicated electrical connection is required. See the Electrical chart for
the proper electrical requirements. Manufactured to be permanently
connected. Consult your local Taylor distributor for cord & receptacle
specifications as local codes allow.
Beater Motor
One, 1.5 HP.
Refrigeration System
One, approximately 15,000 BTU/hr. R404A.
(BTUs may vary depending on compressor used.)
Air Cooled
Minimum clearance: 3” (76 mm) around all sides. Install the deflector
provided to prevent recirculation of warm air. Minimum air clearances must
be met to assure adequate air flow for optimum performance.
Water Cooled
Water inlet and drain connections under side of base 3/8” FPT.
Options
Faucet
Knife Door
Tub Locator
Continuing research results in steady improvements; therefore, these
Taylor Company,
A Division of Carrier Commercial Refrigeration, Inc.
Rockton, Illinois 61072
815-624-8333 800-255-0626 Fax 815-624-8000
www.taylor-company.com
specifications are subject to change without notice.
Printed in U.S.A.
026148-ADV
6/06
Loading...