Taylor 7322 Instruction Manual

Thank you for purchasing a Taylor® Lithium Electronic scale. All of our
precision instruments for weight measurement are engineered and
designed to meet the highest quality standards …to assure you years of
uncompromising accuracy and consistently dependable, convenient
performance.
Please read this instruction manual carefully before use. Keep these
instructions handy for future reference.

1. Clean exposed parts with a soft, slightly damp cloth. To remove
stains, use a mild soap. Never use detergents, excess water, treated
cloths, harsh cleaning agents, or sprays. Do not attempt to lubricate
or open scale casing as this will void your warranty.

2. Although your scale is designed to be maintenance-free, it contains
sensitive electronic parts. Avoid rough treatment. Do not drop, kick,
or jump on it. Treat it with care to ensure the best performance.

3. This scale is designed to read weights between 25 and 330 lbs and
12 and 150 kgs. To prevent damage, do not place more than 330 lbs
or 150 kgs on it.

4. Do not store scale where you store cleaning chemicals. The vapors
from some household products may affect the electronic components
of your scale. Do not store scale on its side.

5. This scale is an extremely sensitive weighing device. In order to
prevent run down of the battery, do not store anything on the scale.

6. Do not dispose of batteries in fire. Batteries may explode or leak.
Remove the battery if the scale will not be used for a long period of
time.

1. There is a red strip under the Lithium battery cover to prevent
battery drain in shipping. Please remove the strip before continuing
with these instructions. Also, some models have a static cling label
on the lens to prevent scratching. Please remove before use.

2. Your scale has been set at the factory to read weight in pounds. You
may select kilograms by moving the slide switch on the bottom of the
scale.

3. Place scale on flat, hard surface. Carpeted or uneven floors may
affect accuracy.

4. Step on the scale (disregarding the reading) and step off. This
process insures the scale is set and is now ready for use. Do this
whenever the scale is moved. At all other times step straight

onto the scale.

5. Step onto the scale platform and remain still. The display will show

“0.0 ”, then count up to your weight. The display will flash twice
when the weight is locked. Your weight is now displayed.

6. If you step off of the scale, the display will turn off automatically
within 5 seconds. If you continue to stand on the scale, your weight
will be displayed for 30 seconds and then the scale will turn off
automatically.

Your Taylor® scale has a lithium battery installed to provide extra long
energy life for your scale. Under heavy usage (Health Club, Wellness
Clinic, etc.) the battery may eventually need to be replaced.

Maintaining proper weight is essential to healthy living. Obesity
has been linked to a higher risk of heart disease, diabetes and
some forms of cancer. The Body Mass Index (BMI) is the most
widely accepted measurement of weight according to health
professionals.
Use the chart below to determine your own BMI by matching
your height in the left hand column with your weight in the
center. Anyone, male or female, with a BMI of 25 to 29 is
considered over weight and a body mass index of 30 is
considered obese. Remember to eat right and exercise.

In Case of Difficulty...

1. Place your feet in the same position every time you weigh

yourself. Stand still during measurement.

2. Weigh yourself without clothing whenever possible. Clothes can
vary in weight.

3. Move the scale to a location where it won't be bumped. If your
scale is bumped while being activated or while in use, an
inaccurate reading may occur.

4. For the most consistent readings, weigh yourself at the same
time of day. Allow for weight fluctuations due to food or drink in
your system.

5. The maximum capacity of this scale is 330 lbs / 150 kgs. Should
“Err ” appear on the display during a weighing, this indicates that
the maximum weighing capacity of the scale has been exceeded.
Remove the weight immediately; otherwise, permanent damage
may occur.

CP7322 12.10

Lithium
Electronic Scale

Battery Replacement

Reaching Target Weight

Low Battery

Trouble Shooting

General Operation

Battery Information

7322

Leading the Way in Accuracy®

1. Use one 3 volt CR2032 lithium battery (as installed).

2. Open the battery compartment on the bottom of the scale by

pushing the tab in the direction of the “open” arrow and lifting up
the cover.

3. Remove the old battery from the compartment.

4. Place the new battery with the “+”

sign up into the battery compartment.

5. Push gently down on the compartment
cover until it clicks shut.

Your Taylor® scale is equipped with a low
battery indicator. It will display “ LO ” or
readings will grow dim or become irregular
if the battery needs replacement.

Five (5) Year Limited Warranty

There are no express warranties except as listed above. This warranty gives you specific
legal rights, and you may have other rights which vary from state to state.

For additional product information, or warranty information outside the USA, please
contact us through www.taylorusa.com.

©2010 Taylor Precision Products and its affiliated companies, all rights reserved. Taylor®
and Leading the Way in Accuracy® are a registered trademarks of Taylor Precision
Products and its affiliated companies. All rights reserved.

Made to our exact specifications in China.

Not legal for trade.
www.taylorusa.com

This scale is warranted against defects in materials of workmanship five (5)
years of the original purchaser from date of retail purchase (excluding
batteries). It does not cover damages or wear resulting from accident, misuse,
abuse, commercial use, or unauthorized adjustment and/or repair. Do not
return to retailer. Should this scale require service (or replacement at our
option) while under warranty, please pack the item in the original packaging
and return it prepaid, along with store receipt showing date of purchase and a
note explaining reason for return to:

Taylor Precision Products

2220 Entrada Del Sol, Suite A

Las Cruces, New Mexico 88001 USA