Tatung TLM1905, TLM-1705 User Manual
OPERATING INSTRUCTIONS
TLM-1705 / TLM1905
PREFACE
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Opeartion is subjected to
the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference
that may cause undesired operation.
FCC WARNING
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
inerference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution:
To comply with the limits for an FCC Class B computing device, always use the
shielded signal cord supplied with this unit.
i
The Federal Communications Commission warns that changes or modifications
of the unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
CE mark for Class B ITE (Following European standard EN55022/1998; EN610003-2/1995; EN61000-3-3/1995, EN55024/1998, EN60950/1992+A1+A2+A3+A4+A11)
Radio Frequency Interference Statement
Warning:
This is a Class B product. In a domestic environment, this product may cause
radio interference in which case the user may be required to take adequate
measures.
Canadian Doc Notice
For Class B Computing Devices
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus as set out in the Radio Interference Regulation
of the Canadian Department of Communications.
“Le présent appareil numérique n’èmet pas de bruits radioélectriques dépassant
les limites applicables aux appareils numériques de la class B prescrites dans le
Règlement sur le brouillage radioélectrique édicté par le ministère des
Communications du Canada”
ii
Important Operating Instructions
Please read the following instructions carefully. This manual should be retained
for future use.
1. To clean the LCD monitor screen, first, make sure the monitor is in the
power off mode. Unplug the monitor from its power source before cleaning
it. Do not spray liquid cleaners directly onto the unit. Without applying
excessive pressure, clean the screen with a slightly dampened rag.
2. Do not place your LCD monitor near a window. Exposing the monitor to
rain, water, moisture, or sunlight can severely damage it.
3. Do not place anything on top of the monitor-to-PC signal cord. Make sure
the cord is placed in an area where it will not be stepped on.
4. Do not apply pressure to the LCD screen. Excessive pressure may cause
permanent damage to the display.
5. Do not remove the cover or attempt to service this unit by yourself. You may
void the warranty. Servicing of any nature should be performed only by an
authorized technician.
6. Safe storage of the LCD monitor is in a range of minus 20 to plus 60 degrees
Celsius. Storing your LCD monitor outside this range could result in
permanent damage.
7. Immediately unplug your monitor and call an authorized technician when:
• The power or monitor-to-PC signal cord is frayed or damaged.
• Liquid has been spilled into the monitor, or it has been exposed to rain.
• The monitor has been dropped or the case has been damaged.
8. Only with use of supplied adaptor, in case of loss or replacement contact the
retailer or service center.
9. If you lost the power cord that we given, you must to purchase a same
configuration/type of power cord (with ground-connection)
Japan： VCTF type, 3 wires or with ground-wire, T-mark approval is
required.
U.S.：VW-1; 18AWG X 3C; SVT with national approval as UL
and/or CSA approval/number(s)
Europe：VDE/ÖVE and/or KEMA approval; H05VV-F, 3G,
2
0.75mm
, or equivalent.
Above power cord should bear with the type and manufacturer name on.
iii
Introduction
CONTENTS
PREFACE .....................................................................................................................I
CHAPTER 1................................................................................................................. 1
Unpacking 1
Identifying Components 2
The LCD Multimedia Monitor — Front View 2
The LCD Multimedia Monitor — Rear View 2
Adjusting the Tilting Angle 3
Raising Your Monitor to an Upright Position and Adjusting Monitor Angle4
Power Management System 5
CHAPTER 2................................................................................................................. 6
LCD Multimedia Monitor Control Panel 6
Adjusting the Monitor’s Display 7
OSD Main Menu 7
Hot-Key Buttons for Quick Adjustment of Monitor Settings. (〝AUTOADJUST〞hot-key is effective only when analog input signal is selected for
application) 16
APPENDIX A............................................................................................................. 17
Troubleshooting Procedures 17
APPENDIX B ............................................................................................................. 19
LCD Monitor Specifications 19
APPENDIX C............................................................................................................. 21
iv
CHAPTER 1
The LCD Multimedia Monitor
Unpacking
After you unpack your LCD multimedia monitor, make sure the following items are
included in the box and in good condition:
Standard Item
• LCD multimedia monitor
• Monitor-to-PC analog signal cable (15-pin)
• Monitor-to-PC digital signal cable (24-pin) – (Optional)
• Power cord
• Addendum
• User’s manual
• 1.5M Stereo Jack audio cable
If you find that any of these items are missing or appear damaged, contact your dealer
immediately. Do not throw away the packing material or shipping carton in case you
need to ship or store the LCD multimedia monitor in the future.
1
Identifying Components
The LCD Multimedia Monitor — Front View
Figure 1-1: The LCD multimedia Monitor Front View
1. Power-On Indicator
This LED indicator stays lit when the power is on and blinks
when the LCD multimedia monitor is in power saving mode.
2. Monitor Stand
3. LCD Screen
4. LCD Multimedia Monitor Control Panel
Refer to Chapter 2 for a detailed.
The LCD Multimedia Monitor — Rear View
Figure 1-2: LCD Multimedia Monitor Rear View
2
1. Audio Line-in
2. AC Power Jack
3. VGA (Analog) Cable With 15-Pin D-Sub VGA Connector (Male)
4. S-Video connector
5. AV connector
6. Digital VGA (DVI) Cable Connector (Optional)
Adjusting the Tilting Angle
The LCD multimedia monitor’s angle settings range from -3° to 20°. See Figure 1-3.
Figure 1-3: Tilting the Monitor
3
Loading...