TATUNG TDR series Digital Recording System Page 0
TDR
-22XX series
TATUNG COMPANY
OF AMERICA. INC
Digital Recording System
Installation and Operation Manual
V 1.01
2850 El Presidio St., Long Beach CA 90810 USA
Tel: 310-637-2105 Fax: 310-638-2180
www.tatungusa.com
TATUNG TDR series Digital Recording System Page 0
TATUNG TDR series Digital Recording System Page 0
Chapter 1:
Installation
1
CONTENTS
Step 1 Connect the cables 2
Step 2 Turn on the system 2
Chapter 2: Watch Mode 3
2.1 Channel display window 5
2.2 Selection of Split screen 6
2.3 Motion Tracker 7
2.4 Mode switch button 8
2.5 On/Off button 8
Chapter 3: Setup Mode 9
3.1 Channel 11
3.2 Schedule 13
3.3 Speed 15
3.4 Color 17
3.5 Motion 18
3.6 P/T/Z Control 20
3.7 Password 21
3.8 Voice 24
3.9 Exit 25
Chapter 4: Search Mode 26
4.1 Channel Play back window 28
4.2 Buttons on Play Back Console 29
4.3 Date/Time 30
4.4 Log 32
4.5 Save Disk 33
4.6 Print 34
4.7 Storage Capacity 35
4.8 Exit 35
Chapter 5: Backup Mode 36
5.1 Auto Backup 37
5.2 AVI Backup 39
5.3 Explorer 40
5.4 Cancel 40
Chapter 6: Control Mode 41
6.1 Camera Control 41
6.2 Exit 42
Appendix
A: Technical Specification 43
B: Connector Configuration 46
TATUNG TDR series Digital Recording System Page 0
TATUNG TDR series Digital Recording System Page 1
Place the Digital Recording System on the flat surface or
* For TDR
-2209 there are only 9 camera Inputs and 9 Loop through outputs on
CHAPTER 1: INSTALLATION
mount it on the 19” rack.
the back board. For TDR-2204 there are only 4 camera Inputs and 4 Loop
through outputs on the back board.
1. Camera Inputs
2. Loop Through output
3. Reserved
4. CCTV Monitor output
5. Alarm Inputs
6. Alarm Outputs
7. Audio In
8. Microphone Jack
9. Audio Out
10. COM series port
11. Printer (LPT) port
12. PC Monitor Output
13. Mouse (PS/2)
14. Keyboard (PS/2)
15. Network port (RJ-45)
16. AC Power Input
17. 115/230 VAC Power Switch (option)
18. Power Supply Switch (option)
TATUNG TDR series Digital Recording System Page 2
Au
dio In Audio Out
Camera In
Camera Out
CCTV
Alarm In/Out
Protect
PC
Network Port
Power In
Removable Storage
CDRW
* For TDR
-
2209 there are only 9 camera Inputs and 9 Loop through outputs on
Step 1: Connect the Cables
Connect all the necessary connector and signal cables into the correct ports.
Monitor Out
Monitor
Output
Socket
and
LPT
the back board. For TDR-2204 there are only 4 camera Inputs and 4 Loop
through outputs on the back board.
Step 2: Turn on the System
Turn on the power by push the power button on the front panel.
Reset
Power
TATUNG TDR series Digital Recording System Page 3
CHAPTER 2:
WATCH MODE
The buttons and icons on the screen are described below:
Note
: For TDR
-
2209 there are
Note
: For TDR
-
2209, the Butt
on
Turn on the system. The main screen of TATUNG TDR -22XX series appears as below.
only 9 channels split the screen.
For TDR-2204 there are only 4
channels split the screen
of 9 Sequence and the button of
16 will show the all 9 channel at
same time. : For TDR-2204, the
Button of 4 Sequence, the button
of 9 Sequence and the button of
16 will show the all 4 channel at
same time.
1. Company LOGO
This is the logo of TATUNG Company of America.
2. DATE/TIME Window
This window displays the date and time.
3. 1 Sequence Button
Click to select the 1-window (1x1) format. Only 1 camera can be
displayed at a time. The sequential dwell time can be adjusted in
SETUP mode.
4. 4 Sequence Button
Click to select the 4-window (2x2) format. Up to 4 cameras can be
displayed at the same time. The sequential dwell time can be adjusted
in SETUP mode.
5. 9 Sequence Button
Click to select the 9-window (3x3) format. Up to 9 cameras can be
displayed at the same time. The sequential dwell time can be adjusted
in SETUP mode.
6. 16 Button
Click to select the 16-window (4x4) format. Up to 16 cameras can be
displayed at the same time. The sequential dwell time can be adjusted
in SETUP mode.
TATUNG TDR series Digital Recording System Page 4
7.
Full SCR Bu
tton
This button allows you to hide all buttons and icons and enlarge the
display windows to the FULL SCREEN. You have to right click to get
back to normal. Once you get the full screen, if you LEFT click, the
screen can not go back to normal, instead, the picture the mouse
arrow sitting on will be enlarged to full screen.
8. Motion Button
Click to enable the motion tracking function. This is a very powerful
function which allows you to track a moving object from one channel
to another. All image windows this object passed by will be enlarged
one by one.
9. Setup Button
Click to switch to SETUP MODE. The setup mode includes buttons of
CHANNEL, SCHEDULE, SPEED, COLOR, MOTION, P/T/Z
PROTOCOL, PASSWORD, and VOICE. With these buttons your
system can be custom- programmed to fit your operation needs.
10. Search Button
Click to switch to SEARCH MODE. In this mode, you may either use
LOG button to check the image database or use DATE/TIME button
to get the recorded images within seconds. The images found may
either print out or save to a floppy disk for your emergency needs.
The usage of the storage can be found by STORAGE button.
11. Backup Button
Click to switch to BACKUP MODE. In this mode, you may either
choose auto-backup function to save images to a second removable
hard disk or choose AVI backup function to save images onto a
CDRW available from this system.
12. Control Button
Click to switch to CONTROL MODE. In this mode the
PAN/TILT/ZOOM of each camera can be controlled by clicking the
buttons on the screen.
13. On/Off Button
Click to turn off the entire system.
14. Display windows
Display camera images on 1, 4, 9 or 16 windows depending on your
selection. Left click a window will enlarge the picture in that specific
window. And left click again the picture will go back to the normal
size. RIGHT click any window will hide all buttons and icons and
enlarge all pictures. And right click again will go back to normal
15. On Screen Display (OSD)
Display the camera name and recording status. The recording status
indicates camera active or inactive and the recording method
(continuous recording, motion recording or alarm recording).
TATUNG TDR series Digital Recording System Page 5
1.
Channel
(Camera)
name
2.1 Channel display window
1. Channel (Camera) name
2. Image display window
3. Record status lamp
Identify the name for each channel. You may assign the channel name in
SETUP mode.
2. Image Display window
This area displays the image comes from the camera.
3. Recording status lamp
This lamp turns red at consecutive recording
When motion recording, this lamp becomes blue and white. (on and
off)
At sensor recording, this lamp turns yellow and white. (on and off)
TATUNG TDR series Digital Recording System Page 6
Note: You can always use
Note
: At
all
Ch Display, left
Note
: For TDR
-
2209, the
b
utton
2.2 Selection of Split screen
Selection of window division mode that is available in 1 division window (sequence from channel 1
to channel 16), 4 window, 9 window, 16 window, and Full screen display.
Click on the one of these buttons to perform the function
click a specific camera, the
image of this camera will be
enlarged without sequencing.
And left-click again can go
back to the normal status.
of 9 Sequence and the button of
16 will show the all 9 channel at
same time. : For TDR-2204, the
button of 4 Sequence, the button
of 9 Sequence and the button of
16 will show the all 4 channel at
same time.
one-window Sequence
four-window Sequence
nine-window Sequence
all channel
right-click on mouse to
switch between these Full
screen status and normal
screen status.
FULL screen
Click this button to hide all buttons and icons and enlarge the display
windows to FULL screen. You must right click on mouse or touch pad to
go back to the normal.
TATUNG TDR series Digital Recording System Page 7
Click on this button to enable the motion tracking function.
Note
: To enable this
2.3 Motion Tracker
This function allows you to track the path of a moving object from one channel to another. All image
windows this object passed by will be enlarged. Therefore, the object will always display on an
enlarged window.
function, all channels
need to be programmed
to motion recording.
TATUNG TDR series Digital Recording System Page 8
Click
on the one of these buttons to perform the function
Click on
this button and click on “YES” as the system prompt out “ARE YOU SURE?”
2.4 Mode Switch button
There are four function modes can be selected in this system.
SETUP: Click to switch to SETUP MODE. The setup mode
includes buttons of CHANNEL, SCHEDULE, SPEED,
COLOR, MOTION, P/T/Z PROTOCOL, PASSWORD, and
VOICE. With these buttons your system can be custom programmed to fit your operation requirements.
SEARCH: Click to switch to SEARCH MODE. . In this mode, you
may either use LOG button to check the image database
or use DATE/TIME button to get the recorded images
within seconds. The images found may either be printed
out or saved to a floppy disk for your emergency needs.
The usage of the storage can be found by STORAGE
button.
BACKUP: Click to switch to BACKUP mode. It can backup the data
to the other storage or other type of media which is
available for this system. This mode include the auto backup function, immediate AVI type backup function and
have a windows explorer opened for your convenience.
CONTROL: Click to switch to CONTROL MODE. In this mode the
PAN/TILT/ZOOM of each camera can be controlled
by clicking the buttons on the screen.
2.5 ON/OFF Button
to shutdown the DVR system.
TATUNG TDR series Digital Recording System Page 9
CHAPTER 3: SETUP
MODE
The control buttons contained in the main screen are described below:
Note
: For TDR
-
2209, CH 10 to
The first screen of the setup mode will be the channel setting as the following picture
CH 16 will be empty by the
factory’s setting. For TDR-2204,
CH 05 to CH 16 will be empty by
factory’s setting
1. Channel
Click on this button to setup the channel and channel name. There are two
different ways to setup the channel -automatically scan and manually
designate. You can also set the name for each channel.
2. Schedule
Click this button to setup the recording schedules. There are 16 recording
groups and three recording modes (continuous, motion, sensor) can be
separately set up for your application. Alarm output can also be set up
separately.
3. Speed
Click to assign the recording speed and other options. The recording
speeds include speeds on normal recording, motion recording, and sensor
recording. You can also set up the times for display sequence, post alarm
and post motion in this mode.
4. Color
Click to adjust the image color, including the adjustment of Brightness,
Contrast, Color (saturation), and TINT for each indi vidual channel.
5. Motion
Click to assign the motion function. You can set up each individual
channel’s motion detection area (up to 10 zones for each channel),
sensitivity, and the beep time for motion detection.
TATUNG TDR series Digital Recording System Page 10
6.
P/T/Z camera protocol
Click to setup the communication port and protocol used to communicate
between Tatung’s DVR and the camera connected.
7. Password
Click on this button to setup the user name and password for access security.
The passwords are divided in SETUP, VIEWER, SHUTDOWN, and REMOTE
four levels. Hiding camera can also be programmed with this setup.
8. Audio
Click to setup the audio recording function.
9. Exit
Click to exit to the setup mode and back to watch mode.
TATUNG TDR series Digital Recording System Page 11
This is the first
Click to have the list.
Click this button to start the channel setup and the screen will be
shown as below.
First Channel
Note
: For TDR
-
2209, CH 10 to
3.1 Channel
This function button (as shown below) can be us ed to setup the channels. There are two different
types of channel setting, manual or automatic.
CH 16 will be empty by the
factory’s setting. For TDR-2204,
CH 05 to CH 16 will be empty by
factory’s setting
You can setup the channel either by auto setting or manual setting.
1. Setup the Channel
Auto
Setting
Manual
Setting
Click on the setup will be executed automatically
Select the Board (B01-B04) and Channel
(C01-C04) from the list to setup the
Channel Name
Board and first
Camera
CH01
Select the Board # and
Camera # from the list.
Then left -click
TATUNG TDR series Digital Recording System Page 12
1. Click to
2
. Key in the
2. Setup the name
Setup the channel name by following the procedure
1. Click the channel number
2. Key in the name of the channel
3. Limited to 14 characters and number including space.
channel name
here
choose channel
3. EXIT
You may click any other icon to exit Channel Setup Mode and go directly into
other setup mode. Click EXIT button, you will be back to Watch Mode.
TATUNG TDR series Digital Recording System Page 13
Click on this button to start schedule setup and the screen will display as
Note:
The shutdown time is
Note
: For TDR
-
2209, Camera’s
Note
: Alarm Out 09 to 16 was
3.2 Schedule
This function button (as shown below ) is used to setup the schedules.
CH 10 to CH 16 and Motion’s
CH 10 to CH 16 will be useless
even you activate it. For TDR2204, Camera’s CH 05 to CH 16
and Motion’s CH 05 to CH 16 will
be useless even you activate it.
not configured in all TDR-22XX
series DVR.
to set the time for turning off
the system, which is different
to the restart system.
Select the Group number (total 16 groups are available and
programmable).
Activate the group by checking the box.
follow. (Please follow the 7 steps below)
1. Select the Group
2. Activate Group
3. Schedule the Recording DATE/TIME and DVR Shutdown Time
• Setup the days of the week (Sunday to Saturday) by checking the box of the
day.
• If you want to assign the recording time (default is 24 hours), setup [Start
Time] and [End Time] by using military time system. (00:00 to 00:00 means
24 hours).
• If you want to assign the shutdown time, check the box of Shutdown Time
and setup the time.
TATUNG TDR series Digital Recording System Page 14
4. Activate the camera
Click the camera icon to activate the cameras which are used in this group.
5. Select the Recording mode
Select the recording mode for each channel. There are three recording modes.
DEFAULT Continuous recording
Motion
Sensor
Record while motion detected
Record while Sensor is active
6. Setup Alarm Out: Alarm Output may setup when either a sensor is triggered or
motion is detected.
7. Set up another group
Repeat the step from 1 to 5 if you want to set up another group.
8. Exit
You may click any other icon to exit Schedule Setup Mode and go directly
into other setup mode. Click EXIT button to go back to Watch Mode.
TATUNG TDR series Digital Recording System Page 15
3.3 Speed
This function button (as shown below) can be used to setup the recording speeds.
Click this button the screen displays as below.
Normal Recording Speed
Dragging the cursor can designate normal recording speed (frame rate) for each
camera or all cameras (Separate frame rate for each camera is available).
Motion Recording Speed
Dragging the cursor can designate motion recording spe ed (frame rate) for each
camera or all cameras (Separate frame rate for each camera is available).
Sensor Recording Speed
Dragging the cursor can designate sensor recording speed (frame rate) for each
camera or all cameras (Separate frame rate for each camera is available).
Sequential Time
Adjust the dwell time interval for sequential display.
Post Motion Time
Keep recording for a period of time after motion detection is over.
Post Alarm Time
Keep recording for a period of time after sensor alarm is finished.
TATUNG TDR series Digital Recording System Page 16
MISC
Check on the box if you want the following features to be enabled.
Sensor Beep Activate beep sound when sensor is triggered.
Proportion
Motion Log Activated Motion log function.
When activated, only 1, 4, 9, 16 divisions are available, to
keep the horizontal and vertical ratio of each channel window.
Recording While
Searching
Removable HDD System Will BEEP when the removable HDD is almost full.
Continue to record when the system in search mode.
Image Quality
Dragging the cursor can adjust the compression rate, the higher the compression the
worse the image quality. The recorded image with best quality (100%) is clear and
vivid. But the size of a frame is the largest (15KB-20KB). At lower percentage of
quality (higher compression rate) image quality is relatively low. But the size of a
frame is relatively small (3KB-8KB). 34% -50% of image quality is recommended.
Compression Rate Image Quality
HIGH
LOW
10%
20%
30%
40%
50%
60%
70%
80%
90%
100%
Frame Size**
Range Average
0% 2400-7200 byte
2600-8100 byte
2900-9300 byte
3500-10300 byte
4100-12000 byte
5000-14000 byte
6000-16000 byte
6600-17000 byte
8200-20000 byte
9200-22000 byte
14000-24000 byte
*Frame size may vary from image to image according to the situation of site
EXIT
You may click any other icon to exit Speed Setup Mode and go directly into other
setup mode. Click EXIT button to go back to Watch Mode.
5.0 KB
5.5KB
6.0 KB
7.0 KB
8.0 KB
9.5 KB
11.0 KB
12.0 KB
14.0 KB
16.0 KB
19.0 KB
TATUNG TDR series Digital Recording System Page 17
Bright:
Adjust the brightness.
3.4 Color
This function button (as shown below) is used to setup the colors.
Click this button to setup the color, the screen will be shown as below.
1. Select channel
Select the channel (from 1 to 16) you want to adjust.
2. Adjust the Color
Drag the cursor to adjust the followings for each channel.
3. EXIT
You may click any other icon to exit Color Setup Mode and go directly
into other setup mode. Click EXIT button to go back to Watch Mode.
Const: Adjust the contrast.
Color: Adjust the color saturation.
Tint: Adjust the tint.
Default color: Load default color value.
TATUNG TDR series Digital Recording System Page 18
Click on this button to setup the motion, the screen display as the below
Note:
If no detection zone was
Note:
After the
camera is
3.5 Motion
This function button (as shown bel ow) can be used to setup the motions.
Select the channel from 1 to 16.
defined, system will recognize
the whole windows as a
detection zone.
Setup the motion detection zone for each channel by click and drag. It would be
seen in red square (Maximum 10 areas per camera).
motion activated in Schedule
Motion beep
Setup Mode and after the
In motion recording mode, BEEP sound (if the speaker was included in the
detect zone is set, this
channel will be motion-
system) can be activated/inactivated by checking the box or not. Beep time can
activated in the define area. If
be also be adjusted by dragging the cursor.
anything falls in this area, the
detected motion will be seen
in a lot of small blue squares.
And red wording “MOTION
DETECTION” will be blinking.
(Please following the 4 steps)
1. Select channel
2. Set up motion detection zone.
3. Set up the MISC options.
TATUNG TDR series Digital Recording System Page 19
Sensitivity
Set the sensitivity of software motion detection. At highest sensitivity even very
trivial motion will be detected.
Clear all block
All of the detecting zones for a specific channel.
4. EXIT
You may click any other icon to exit Motion Setup Mode and go directly
into other setup mode. Click EXIT button to go back to Watch Mode.
TATUNG TDR series Digital Recording System Page 20
Click on this button to setup the P/T/Z Protocol, the screen display as the
Click to choose a
Click to assign
3.6 P/T/Z Protocol
This function button (as shown below) is used to setup P/T/Z Protocol.
Please select the same protocol as that of your camera.
You may click any other icon to exit Protocol Setup Mode and go directly into
other setup mode. Click EXIT button to go back to Watch Mode.
below
manufacturer
brand from list
communication
port.
EXIT
TATUNG TDR series Digital Recording System Page 21
Note:
See next page for the
1.
Sel
ect the password type.
Note
: For TDR
-
2209, the Hide
3.7 Password
This function button (as shown below) can be used to setup the password.
Click on this button to setup the Password.
Camera function CH 10 to CH 16
will be useless even you activate
it. For TDR-2204, the Hide
Camera function CH 05 to CH 16
will be useless even you activate
it.
remote access password.
• Password
There are five levels of password for security purpose.
(Please follow the steps below)
2. Key in the new password. (From keyboard, mouse, or touch screen).
3. Click on “Apply” when finished or “Clear” to canceled
TATUNG TDR series Digital Recording System Page 22
NOTE:
To set up the Remote
Sign up
• Remote username/password
Select the Remote Access in the Password Select window. An Input
Password window will be prompted up. After entering the password and
click OK, the following screen will be shown. TATUNG TDR series allow the
administrator to sign up remote users.
username/password. The
system will ask the SETUP
password again to confirm
the authority of the user
§
o Click “Sign up” button will prompt the Register Account window.
o Key in the New ID and Password.
o Then click Entry button.
o Click “Exit” button to leave above window.
§ Delete
o Click on the user’s name in the Registered ID window above.
o Click on “Delete ” button.
o Click “Exit” button to leave above window.
§ Edit User
o Click on user’s name in the Registered ID window above. The
user’s ID and Password will be shown in the “User information ”
and “Select Hide camera ” window.
o If you want to change the password, click the “Change Password”
button. After entering the new password, you have to confirm it.
Then click APPLY and OK in Account window to complete.
o If you want to hide the cameras for this user, check the box for
each camera or click on the button of either “Select All Camera ” or
“Clear All Camera”.
o Click “Exit” button to leave above window.
TATUNG TDR series Digital Recording System Page 23
Note
: For TDR
-
2209, the Hide
• Hide Cameras
Check the box(es) to hide the channel(s) from the server site.
Camera function of Remote
Client CH 10 to CH 16 will be
useless even you activate it. For
TDR -2204, the Hide Camera
function of Remote Client CH 05
to CH 16 will be useless even
you activate it.
• Restart Window
Check the box of the day and assign the time to restart the system.
EXIT
You may click any other icon to exit Password Setup Mode and go directly into
other setup mode. Click EXIT button to go back to Watch Mode.
TATUNG TDR series Digital Recording System Page 24
Click on this button to setup the voice, the screen display as the below
Note:
To have a better voice
Audio
3.8 Voice
This function button (as shown below) is used to setup the voice settings.
(Please follow the steps)
Channel
one
play back quality. The image
recording speed is better to set
to mote than 2 FPS.
Check on this box to enable the sound recording.
Adjust this number to coordinate the synchronization of sound playback and
video playback. The number 700 means the system coordinates the
synchronization every 700 seconds. The faster the image recording speed, the
smaller the delay time should be chosen. This means the two playbacks need
to be coordinated more frequently. However, if the image recording speed is
slow, we may choose longer time (large number) to coordinate the two
playbacks.
For TDR-22XX series, audio can be recorded only in channel one (01).
1. Check the box of “sound”
2. Adjust the “Play Sound Delay”
3. Check on the box of the channel you want to activate
4. EXIT
You may click any other icon to exit Voice Setup Mode and go directly int o other
setup mode. Or click EXIT button to go back to Watch Mode.
TATUNG TDR series Digital Recording System Page 25
Note:
You can always click on
3.9 Exit
Click on EXIT button to switch back to WATCH MODE after you complete all the setting in the
SETUP mode.
the EXIT to switch back to
watch mode no matter what
function mode you are in.
TATUNG TDR series Digital Recording System Page 26
CHAPTER 4: SE
ARCH
MODE
The buttons and icons of the main screen are described below:
Note
: For TDR
-
2209 there are
The main screen of the search mode is shown below.
only 9 channels split the
screen. For TDR-2204 there
are only 4 channels split the
screen
1. Date/Time
Click on this button to search the images from Date and Time. A calendar
like data selection window including From -Time and To-Time will be
prompted up.
2. Log
Click this button can check the sensor recording log and motion recording
log of the system. It can also search the images from these logs.
3. Save Disk
Click this button to save a short period of images to a floppy disk. Channels
and frames are selectable in this function.
4. Print
Click to print the specific image on the system printer as an immediately
data retrieve. Channels and frames are selectable in this function no matter
the printer is a local printer or a network printer.
5. Storage Capacity
Click to check the usage information of the data storage (removable HDD).
The information includes both the sound recording capacity and the image
recording capacity.
6. Buttons on Play Back Console
These control buttons are used to playback the data, Which includes the
starting of the record, 1 previous minute, 1 previous frame, playback, quick
play, stop, 1 next frame, 1 next minute and the ending of the record.
TATUNG TDR series Digital Recording System Page 27
7.
Exit
Click this button to exit the Search Mode and back to the Watch Mode.
8. Mute Box
Check this box to disable the audio playback.
9. Channel playback window
This is the area to display the playback images along with the channel names and
the recording date and time.
TATUNG TDR series Digital Recording System Page 28
Check this box to mute the
Channel
Note:
The digital zoom works
Note:
You can always enlarge a
Time indicator indicates this image was
Note
: For TDR
-
2209 there are
4.1 Channel play back window
This area is the 16 channels play -back window. All channels can be played back synchronously.
specific channel by left clicking
on this channel and left click
again to back to the multi
channel playback mode.
Name
only 9 channels split the screen.
For TDR-2204 there are only 4
channels split the screen
recorded at 19 (o’clock):25 (minutes): 31
(second) 125(millisecond)
play of audio
• Time Indicator:
Displays the time when the image was recorded. Its format is in
hh:mm:ss.(milisec)
• Mute:
Check the Mute box to stop the audio play back.
• Display one specific channel only:
You can always left click a specific channel to put this channel in the middle
of the window and enlarge it. And left click again to back to the multi channel
playback.
only on a playback stopped
channel
• Digital zoom on specific channel
When playback one specific channel, you may enlarge this channel to full
screen by right -clicking. Back to normal only need right clicking again. You
can also check the digital zoom box and enlarge the image step by step by
continuously right clicking on the image or shrink the image step by step (8
steps total) by continuously left clicking. Clear the digital zoom box and left
click the image will go back to the multi channel playback.
TATUNG TDR series Digital Recording System Page 29
Beginning of
1 frame
Quick
1 frame
End of the
1 min
1 min
Note:
You can always playback
4.2 Buttons on Play Back Console
These buttons are used to control the data stream.
the images no matter you are in
the multi channel playback mode
or one specific channel playback
mode.
back
Stop Play
forward
the record
back
play
forward
Record
• START : From the very beginning of the recorded images.
• PREV 1 MIN : BACKWARD one minute from the current playback time.
• PREV FRAME : BACK one frame from the current playback time.
• PLAY : PLAYBACK the images with normal speed.
• QUICK PLAY : PLAYBACK with faster speed.
• STOP : STOP the playback.
• NEXT FRAME : NEXT one frame from the current playback time.
• NEXT 1 MIN : FORWARD one minute from the current playback time.
• END : To the end of the recorded images.
TATUNG TDR series Digital Recording System Page 30
Date selection:
From
-
Time selection:
To-Time selection:
Start:
window will disappear)
EXIT:
Click this button, the screen will prompt out a calendar like data selection
Note:
You can always select the
4.3 Date/Time
This function button is used to search the images from date and time.
date/time no matter you are in
the multi channel playback mode
or one specific channel playback
mode.
window displayed as the below. You may search the images recorded on the
selected date and time. (Please follow the steps below)
Please click on the date with a
red mark to select
Key in the From -Time may also accomplish
by clicking on the arr ows or drag scroll bar.
Key in the To-Time may also accomplish by
clicking on the arrows or drag the scroll bar.
Click on this button to start the
searching. (The whole selection
Click on this button to exit (The whole selection window will disappear)
1. Date selection
Select the date you want to search by clicking the red check mark . If this is
not the correct month, use the arrow to choose the month you
want.
2. From-Time Selection
There are three ways to enter the search starting time or From -Time: Use the
keyboard to enter, click the little arrows, or drag the scroll bar.
3. To-Time Selection
Search ending time or To-Time can also be entered by keying the numbers into
the Hour and Minute blocks, clicking the arrows, or drag the scroll bar.
TATUNG TDR series Digital Recording System Page 31
4. Start
After complete the date and time selection, click on “Start” button to search or
playback the recorded images.(after clicking, the selection window will
disappear).
5. EXIT
If you want to cancel this date and time selection, click “EXIT” to back to the
main screen of the search mode. (The whole selection window will disappear).
TATUNG TDR series Digital Recording System Page 32
Click here to review the
Click here to review
Select the Log
Date
Time
Close Log
Click this button the screen will prompt out a data list displayed as below.
4.4 Log
Function button can be used to search the images from motion recording and sensor recording logs.
(Please follow the steps below)
Sensor Recording Log
the Mot ion
Recording Log
and click here to
playback the data
selection
selection
Search function
List item
1. Sensor Recording Log or Motion Recording Log
Select the log database you want to search.
2. Date
Select the date you want to search.
3. Time
Select the time you want to search.
4. List item
Click on a specific item you want to search.
5. Playback or Close
Click “Play Back” button to review the image you searched, or Close the
function.
TATUNG TDR series Digital Recording System Page 33
N
umber of frames wanted to save for
Channel
Click on this button the screen will prompt out a save disk window as below
Note:
if you choose a specific
4.5 Save Disk
This function button is used to save a short period of images to a floppy disk. Channels and number
of frames are selectable in this function.
(Please follow the steps below)
all channels. Only 1 cut is available if
you choose a specific channel
Image type
selection
channel to save the image.
There will be only on cut is
available for save .
1. Please make sure you insert a floppy diskette.
2. Channel selection
Select either all channel or one specific channel to retrieve.
3. Cut
Assign the number of frames you want to save for all channels. If you choose a
specific channel, then only one frame can be saved.
4. Image type
Select the image type (JPG or BMP)
5. O.K. or NO
Click “OK” button to save or “NO” to cancel.
TATUNG TDR series Digital Recording System Page 34
Click on this button to print the specific image to floppy disk as the
Title that will be printed on the paper.
Number of frame wanted to print for all
Channel
Setup the
4.6 Print
This function is to print the specifi c image on the system printer as the immediately data retrieve.
Channels and frames are selectable in this function.
immediately data retrieve. The screen will prompt out a print window as
below (Please follow the steps)
channels.
selection
PRINTER
1. Please make sure that a system printer has been installed.
2. Channel selection
Select either all channel or one specific channel to retrieve.
3. Cut Print
Assign the number of frames you want to print for all channels. If you choose a
specific channel, then only one frame can be printed.
4. Print or Cancel
Click “Print” button when to print or “Cancel” to canc el the print.
TATUNG TDR series Digital Recording System Page 35
Note:
If the sound recording
Click on this button to leave the Search Mode and back to the Watch Mode.
4.7 Storage Capacity
Function is used to check the usage information of the removable HDD.
function is disabled, the sound
storage space reserved will be
constituted part of the total
storage capacity.
4.8 EXIT
Click on this button to have the prompt out window of storage in formation.
TATUNG TDR series Digital Recording System Page 36
CHAPTER 5: BACKUP MODE
AVI file immediately
Cancel
Backup
Note:
In this mode, the
Note:
In this mode, if you
After clicking the Backup button, the following window is prompted out.
system will hold the
recording. After you complete
the scheduling and back to
watch mode, the system will
record again.
Auto backup Function Windows explorer
want to backup or save the
data into CD- RW DRIVE.
You must have a CD-RW
disk insert into the drive and
have formatted with the
DIREC CD compatible
process.
backup
• Auto Backup
Automatic backup the recorded images from a customized time schedule.
• AVI Backup
Immediately backup the recorded images in AVI format.
• Explorer
Call out the Windows Explorer and let the operator to configure the system.
• Cancel
Leave the Backup Mode and back to Watch Mode.
operation
TATUNG TDR series Digital Recording System Page 37
Note:
The scheduled backup
Note:
You can also search
5.1 Auto Backup
This function is used to back up the recorded images from a customized time schedule. The
execution time of the backup can also be designated. The screen will prompt out the following
window after clicking on the Auto Backup button. (Please follow the steps below)
function is to backup the
previous day’s data. If you
check the box on Sunday, the
system will backup the data
recorded on Saturday at the
execution time on Sunday.
the data from the list by click
on the “File Information
“button.
1. Scheduled Backup
Check the box if you want to enable the auto backup function
2. Scheduled Backup Option
a. Check the box of the days to backup (Sunday to Saturday)
b. Assign the starting time and ending time.
c. Assign the execution time and the backup device
d. Click on Apply button
TATUNG TDR series Digital Recording System Page 38
3. Immediately backup option
If you want to immediately backup some images, skip steps 1 & 2 and follow
the steps below.
a. Assign the backup date
b. Assign the starting time and ending time
c. Select the backup device
d. Execution or Abort
4. Close
Leave the Auto Backup Mode and back to the Watch Mode
TATUNG TDR series Digital Recording System Page 39
Note:
You can also search
5.2 AVI Backup
This function is to back up the selected data immediately to AVI (Windows default audio and video
information file). The screen will prompt out the windows as below after click on this button. (Please
follow the steps).
the data from the list by click
on the “File Information
“button.
1. Camera
Select the camera (channel) to backup
2. Backup Date
Assign the date of the data to backup
3. Date Start Time
Assign the start time of the data for backup of this day
4. Date End Time
Assign the End time of the data for backup of this day
5. File Name
Click on here to choose the file name and device for this backup
6. Start/Stop/Close
Start the backup or stop the backup or close this function and back to watch
mode.
TATUNG TDR series Digital Recording System Page 40
5.3 Explorer
This function is to call out the WINDOWS explorer which let the operator control this system. The
screen will prompt out the Windows explorer as below.
5.4 Cancel
Cancel this function mode and back to watch mode.
TATUNG TDR series Digital Recording System Page 41
CHAPTER 6: CONTROL MODE
Camera
P/T control
Z
OOM
/F
OCUS
/P
RESET
Note
: For TDR
-
2209 there are
The main screen of the control mode is as the following picture
only 9 channels split the screen.
For TDR-2204 there are only 4
channels split the screen
selection panel
panel
Control button
6.1 Camera Control
Control PTZ camera
Camera Selection Panel :
Select the camera you want to control
(The camera number will turn RED when activated)
• PAN/TILT CONTROL Panel:
Pan/Tilt and Autopan control for the camera
TATUNG TDR series Digital Recording System Page 42
ZOOM/FOCUS control
Load the default
• ZOOM/FOCUS/PRESET Panel:
. Zoom/Focus/Preset panel
setting for
selected camera
6.2 EXIT
Click on this button to exit the control mode and back to the Watch mode.
TATUNG TDR series Digital Recording System Page 43
Product
Features
There are 8 alarm outputs and 16 alarm intputs in
TDR
-
22xx Series Digital Recording System
APPENDIX A:
For the past couple of years, digitization has stunned the
global security industry with its irresistible advantages
compared to the analog. Digital technology has brought
users a new concept of security. For security investigator
who doesn’t want to spend hours to review the tape,
Tatung’s TDR-22xx Series Digital Video Recorder (DVR)
is the perfect solution for rapid time-date searching while
recording live at the same time.
Due to its remote access capability, TDR-22xx can be used
as video monitor receiver to increase the revenue for alarm
monitor center. Especially false alarm can be verified if
TDR -22xx works with alarm panel.
Another benefit can be acquired from TDR-22xx is network
surveillance. Corporation owner can look at somewhere
from his desk without spending extra money if computer
network has already been installed in company branches.
Generally TDR-22xx displays images from one, four, nine,
or sixteen cameras on one single XGA monitor. However,
traditional cctv monitor can be connected to view above
images also.
On top of displaying live video or playing back recorded files
while recording at the same time, DVR also features
multiple remote site access/control, and multiple levels of
password.
To meet the exact demands of your application, Models
from a nine-channel, 40 GB HDD to a sixteen-channel unit
with 320 GB HDD (a removable storage with the capacity of
more than one month recording) can be selected.
4 (TDR-2204) /9 (TD R-2209) /16 (TDR-2216) CAMERA INPUTS
• Highest speed, Multi-Channel Recording
• Real time, Multi-Channel display
• Duplex Multi-Channel playback
• High quality images
• High speed searching
• Long Period recording
• Scheduled recording by groups
• Dual Media Device (HDD + CDRW)
• Motion Detection
• Pan/Tilt/Zoom Control
• Network Surveillance and Remote Surveillance
• Integrate with alarm inputs and alarm outputs
• Sound Recording
• Port for any windows Compatible Printer
• Loop-through outputs with auto termination
TDR -22xx. Each signal input can trigger an alarm
recording. This signal will tell DVR either to start
recording, or to record at a higher speed if recording
has already been started. After the event, it can keep
recording for a while according to a post -alarm setting.
Each channel of TDR-22xx can be programmed to
detect motion separately with up to 10 motion zones
and different motion sensitivities.
The high-speed search can be operated in time-date
searching, index searching and event log searching. It
can also be operated to show the storage usage status
and save a specific image into disk for further analysis.
For long-term recording applications, the TDR-22xx
Series DVR are capable of using supplementary
devices to create backups.
Free remote site software is provided with the TDR-
22xx for viewing live and recorded video. The P/T/Z of
the cameras can also be controlled via remote site
software.
The software of TDR-22xx Series DVRs is very
simple. To customize a recording schedule, such as
alarm, motion, or continuous can be easily
programmed at your finger tips.
TATUNG TDR series Digital Recording System Page 44
S
OFTWARE:
MODELS
TDR-22xx
Series image size
Operation System Windows 98 Second edition
Display Speed Real-time
TDR -2216 480FPS
TDR -2209 270FPS
TDR -2204 120FPS
Record Speed
TDR -2216 240FPS MAX
TDR -2209 240FPS MAX
TDR -2204 120FPS MAX
GENERAL
Operation Temperature 41° to 104°F (5° to 40°C).
Relative Humidity Maximum 80% non- condensing
Dimensions 7” H x 17” W x 18” D
(17.78 x 43.18 x 45.72 cm)
Weight (Approximate) 46.2 lb (20.96 kg) unit
58.3 lb (26.24 kg) ship
ELECTRICAL:
Power Voltage 100-240 VAC Switchable, 50/60 Hz
Signal System NTSC/PAL
System Spec
TDR -2216 PIV 1.6GHZ, 128 MB
TDR -2209 PIII 866MHz, 128 MB
TDR -2204 PIII 733Mhz, 64 MB
Image Resolution 320 x 240
Compression M -JPEG
Image Size 2K ~ 20K
Video Inputs
TDR -2216 16 CH
TDR -2209 9 CH
TDR -2204 4 CH
Video Outputs 2 (1 XGA, 1 Composite)
Alarm Inputs
TDR -2216 16
TDR -2209 16
TDR -2204 8
Alarm Outputs
TDR -2216 8
TDR -2209 8
TDR -2204 4
Remote Control PSTN, ISDN, TCP/IP
Pan/Tilt/Zoom RS-232 (to RS-485 with converter)
Supplied accessories: PS/2 Keyboard with mouse, Software
protection socket, Power cable, Windows® 98 SE, Remote site
software, and rack mount ears.
Minimum Requirements for remote site PC:
Pentium II 400 MHz , 64 MB Memory, 4 GB HDD, 8MB AGP Video Card,
10 MBPS LAN, 288 00 MODEM (PSTN mode), MS-Windows 98 / 98SE /
ME / NT 4.0 / 2000 /XP
Compression Rate HIGH LOW
Image Quality
File Size (KB) 2600 ~ 8100 3500 ~ 10300 5000 ~ 14000 6600 ~ 17000 9200 ~ 22000
Very Low
10 %
Low
30%
HDD 16 CH 9 CH 4 CH
40 GB TDR -2216-040 TDR-2209-040 TDR-2204-040
80 GB TDR -2216-080 TDR-2209-080 TDR-2204-080
120 GB TDR -2216-120 TDR-2209-120 TDR-2204-120
160 GB TDR -2216-160 TDR-2209-160 TDR-2204-160
320 GB TDR -2216-320 TDR-2209-320 TDR-2204-320
480 GB TDR -2216-480 TDR-2209-480 TDR-2204-480
OPTIONAL DEVICE
DVD-RAM DRIVE DVD-RAM drive, backup the data to (4.7
GB/9.8 GB) or (2.6 GB/5.4GB) disk,
writes up to 1.38MB/seco nd and reads
up to 2.77MB/second.
ANALOG MODEM 56K external modem Full-on 2-wire phone
lines
RACK MOUNT VT19726DVR 19” Rack mountable CRT
MONITOR monitor with XGA input.
TOUCH SCREEN 19” Rack mountable touch screen monitor,
MONITOR used for replacing the mouse to meet specific
application requirement.
RACK MOUNT Rack mountable keyboard drawer and
KEYBOARD keyboard with touch pad.
W/TOUCH PAD
CONNECTORS:
BNC Camera inputs and loop through outputs
6-pin Mini DIN PS/2 mouse and keyboard
Push-in Alarm inputs, alarm outputs
9-pin D-type COM 1
15-pin D-type XGA monitor port
25-pin D-type Parallel port
BNC Analog monitor output
RJ-45 TCP/IP, LAN/WAN
CERTIFICATIONS
• FCC, CE, Class A (TBD)
• UL, CUL (TBD)
Standard
50%
Good
70%
Best
90%
TATUNG TDR series Digital Recording System Page 45
TDR-22xx Series Storage and Recording time
TDR-
2216
(Hours)
40 GB 4 8 60 6 12 90 8 16 120
80 GB 8 16 120 12 24 180 16 32 240
120 GB 12 24 180 18 36 270 24 48 360
160 GB 16 32 240 24 48 360 32 64 480
320 GB 32 64 480 48 96 720 64 128 960
480 GB 48 96 720 72 144 1080 96 192 1440
TDR-
2209
(Hours)
40 GB 4 8 16 106.6 6 12 24 160 8 16 32 213.3
80 GB 8 16 32 213.2 12 24 48 320 16 32 64 426.6
120 GB 12 24 48 319.8 18 36 72 480 24 48 96 639.9
160 GB 16 32 64 426.4 24 48 96 640 32 64 128 853.2
320 GB 32 64 128 852.8 48 96 192 1280 64 128 256 1706.4
480 GB 48 96 192 1279.2 72 144 288 1920 96 192 384 2559.6
TDR-
2204
(Hours)
40 GB 8 16 32 240 12 24 48 360 16 32 64 480
80 GB 16 32 64 480 24 48 96 720 32 64 128 960
120 GB 24 48 96 720 36 72 144 1080 48 96 192 1440
160 GB 32 64 128 960 48 96 192 1440 64 128 256 1920
320 GB 64 128 256 1920 96 192 384 2880 128 256 512 3840
The estimate number of hours may be lower when the audio record function is activated.
The standard quality is based on the size of 5K~6K per image.
TDR-22xx Series Storage size calculation
To select the correct model, you have to select the size of storage for your application. To calculate the storage capacity, please apply
the equation below.
Image Size
(KB)
5 x
This equation is a generic formula of how TATUNG calculates the storage capacity.
Storage calculation is based on the average image size, the actual size may vary.
The medium quality is equivalent to VCR quality.
Contact the customer service for assistance in calculating the capacity for your application.
240
FPS
120
FPS
x
Best Quality Good Quality Standard Quality
240
FPS
Record Speed
per Second
120
FPS
Best Quality Good Quality Standard Quality
120
FPS
Best Quality Good Quality Standard Quality
FPS
1 x
60
FPS 9 FPS
60
FPS 4 FPS
x Channels x
30
16
FPS
16 x
240
FPS
240
FPS
120
FPS
Records Hours
per DAY
120
FPS
120
FPS
FPS
8 x 30 x 0.0036 = 69.12
FPS 9 FPS
60
FPS 4 FPS
x
60
30
Record
Days
16
FPS
x 0.0036 =
240
FPS
240
FPS
120
FPS
120
FPS
FPS
60
FPS
120
60
FPS 9 FPS
Required Storage
16
FPS
30
FPS 4 FPS
(GB)
TATUNG TDR series Digital Recording System Page 46
Connector Configuration
Camera In
Camera Out
CH 01
CH 16
Alarm In
Ground
Alarm Out
* For TDR
-
2209 there are only 9 camera Inputs and 9 Loop through outputs on
APPENDIX B:
• Camera In/Out
the back board. For TDR-2204 there are only 4 camera Inputs and 4 Loop
through outputs on the back board.
• Alarm In/Out
(Sensor)
(Common)
S 1 S 2 S 3 S 4 S 5 S 6 S 7 S 8 S 9 S
10 S 11 S 12 S 13 S 14 S 15 S 16
NC 1 CM 1 NO 1 NC 2 CM 2 NO 2 NC 3 CM 3 NO 3 NC 4 CM 4 NO 4 NC 5 CM 5 NO 5 NC 6 CM 6 NO 6 NC 7 CM 7 NO 7 NC 8 CM 8 NO
G G G G G G G G
(NC or NO)
8
Loading...