Tatung TCM-1701, TCM-1901, TCM-2102s, TCM-0902, TCM-1402S User Manual

Operating Instructions

For Color Video Monitor

TCM-0902 / TCM-1001

TCM-1002S / TCM-1402S

TCM-1501 / TCM-1701

TCM-1901 / TCM-2102S

TATUNG Company Of America

Table of Contents

1. FCC Information - 2

2. Safety Precautions - 2

3. General Features - 4

4. TCM-0902 Monitor Front and Rear Views - 5

5. TCM-1001 HI-RES. Monitor Front and Rear Views - 6

6. TCM-1002S Monitor Front and Rear Views - 7

7. TCM-1402S Monitor Front and Rear Views - 8

8. TSCM-1501 HI-RES. Monitor Front and Rear Views - 9

9. TCM-1701 HI-RES. Monitor Front and Rear Views - 10

10. TCM-1901 HI-RES. Monitor Front and Rear Views - 11

11. TCM-2102S Monitor Front and Rear Views - 12

12. Operation - 13

13. Specifications - 14

14. Rack Mount Kit Model - 16

1

FCC INFORMATION

This equipment has been tested and found to comply with the limits for a class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications.

However, there is no guarantee that interference will not occur in a particular installation.
If his equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Shielded interface cables and A.C. power cord, if any, must be used in order to comply

with emission limits.

Changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment.

SAFETY PRECAUTIONS

1. Operate this unit only from the type of power source indicated on the label.

2. Do not block or cover ventilation openings on the back or bottom of the monitor cabinet.

3. Do not place this monitor near a radiator or heating vent.

4. Do not push objects of any kind through cabinet openings. This may result in fire or
electrical shock.

5. Before adding attachments always ask a service technician to perform routine safety
tests to determine that equipment is in safe operating condition. Ground potential tests
should be part of the routine safety check made by the service technician.

6. Do not place monitor on an unstable cart, stand, or shelf where it may fall and injure
personnel or damage equipment.

2

7. Route power cords so that they cannot be walked upon or tripped over. Do not allow

anything to rest on the power cord.

8. Do not install monitor in wet areas, or where it may be exposed to rain or water. Do not

spill liquid of any kind on the unit.

9. Unplug the power cord from the unit before cleaning the display. Use only a damp cloth.

Do not use alcohol, spirits, or ammonia to clean the display. DO NOT ATTEMPT TO
CLEAN THE INTERIOR OF THIS UNIT- THIS ACTION MUST BE PERFORMED BY
THE SERVICE TECHNICIAN AS REQUIRED DURING NORMAL MAINTENANCE.

10. Refer all servicing to qualified service personnel. REMOVAL OF BACK COVER BY

UNAUTHORIZED PERSONNEL MAY EXPOSE THE USER TO DANGEROUS
VOLTAGES OR OTHER HAZARDS.

12. Unplug the unit immediately and notify the service technician.

A. If liquid has been spilled into the display or the display has been exposed to rain

or water.
B. If the unit has been dropped or the cabinet damaged.
C. If fuses continue to blow.
D. If the power cord is damaged or frayed.

E. If a distinct change from normal operation is apparent.

When replacement parts are required, be sure that the service technician uses
components specified by the manufacturer which have the same characteristics as the
original parts. UNAUTHORIZED SUBSTITUTIONS MAY RESULT IN FIRE, ELECTRICAL
SHOCK OR OTHER HAZARDS.

Upon completion of any service or repairs, ask the technician to perform

safety checks to determine that the equipment is in safe operating condition.

WARNING: Serious shock hazards exist within the covers of this monitor. Do not open the
covers under any circumstances, there are no user serviceable components inside.

3

GENERAL FEATURES

1. Compatible With : NTSC / PAL System

2. Scanning System : NTSC, 525 Lines, 60 Hz or PAL, 625 Lines, 50 Hz

3. Video Input Signal : CVBS1 / CVBS2 / S-Y/C

4. Audio Input Signal : AU1 / AU2

5. Input Power : 100~240V AC

6. Limited twelve months warranty

STANDARD SYSTEM COMPONENTS AND ATTACHMENTS

The various components and attachments are shown below:

TCM-0902 TCM-1001 TCM-1002S

TCM-1402S TCM-1501 TCM-1701

TCM-1901 TCM-2102S

4

TCM-0902 MONITOR FRONT AND REAR VIEW

Front View

1. Power On/Off Switch

2. Power-On Indicator

3. Contrast Adjustment

4. Brightness Adjustment

5. Tint Adjustment

6. Color Adjustment

7. Sharpness Adjustment

8. Volume Adjustment

9. CVBS1 / CVBS2 / S-Y/C Select Switch TCM-0902

Rear View

1. Power Inlet

2. Video 1 Input : BNC Connector

3. Video 1 Output : BNC Connector

4. Video 2 Input : BNC Connector

5. Video 2 Output : BNC Connector

6. Audio 1 Input : RCA Jack

7. Audio 1 Output : RCA Jack

8. S-Y/C Input Connector

9. S-Y/C Output Connector TCM-0902

5