Targus PMK050 Setup Manual

RF Optical Mouse Charger

Setting Up the Charger

1 Insert the DC connector end of the adapter into the DC jack on the back of the charger.

RF Optical Mouse Charger

2 Plug the adapter into an available power outlet.

The charger’s LED light glows red.

3 Plug the standard USB end of the receiver into the USB port on the back of the charger.

For optimal performance and RF reception, place the charger at least 8 inches (20 cm) away from all electrical
devices, such as your monitor, speakers or external storage devices.

Installing the Batteries

Before seating your mouse in the charger, you must install the supplied heavy-duty NiMH rechargable batteries to
avoid possible damage.

To install the batteries:

1 Remove the battery cover from the bottom of the mouse by pressing the battery cover tab and sliding it off.

NOTE: The battery cover is also the top cover of the mouse.

2 Remove the current batteries (if installed).

3 Insert the supplied batteries, making sure that the positive (+) and negative (-) ends of each battery match the

polarity indicators inside the battery housing.

4 Slide the battery cover back into position until it “clicks” firmly into place.

The optical sensor, located on the bottom of the mouse, glows red.

WARNINGS: When replacing the batteries, use only heavy-duty NiMH rechargeable batteries. Avoid mixing new
and used batteries in a device. Never use an alkaline battery with a NiMH battery in a device.

Charging the Batteries for the First Time

Before you use your mouse, you must fully charge the batteries. To do this:

1 Seat your mouse in the charger so that it makes a firm connection with the charging plates.

2 Plug the power adapter into an available power outlet (if unplugged).

3 Allow the mouse to remain in the charger for at least ten hours before using it.

USB port

DC jac

k

LED

Mouse
receiver

Technical Support

In the unlikely event that you encounter a problem with your Targus accessory, please contact our technical support team at:

Email: [e-mail] (English)

[e-mail] (Japanese)

Internet: http://www.targus.com/support.asp

Our knowledgeable staff is also available to answer your questions through one of the following telephone numbers.

US

Monday through Friday, 8:00 a.m. (08:00) to 8:00 p.m. (20:00) Eastern time: 800-283-6325

Canada

Monday through Friday, 9:00 a.m. (09:00) to 5:00 p.m. (17:00) Eastern time: 888-827-4877

Australia

Monday through Friday, 8:30 a.m. (08:30) to 5:00 p.m. (17:00) Eastern time: 800-641-645

Targus Asia Pacific - South Asia

Monday through Friday, 9:00 a.m. (09:00) to 6:00 p.m. (18:00): ([phone]

Targus Asia Pacific - Hong Kong

([phone]

Tar g u s Ko r e a

Monday through Friday, 9:00 a.m. (09:00) to 6:00 p.m. (18:00): ([phone]

Targus Japan Ltd.

Monday through Friday, 10:00 a.m. (10:00) to 5:00 p.m. (17:00): 045-232-3082

Europe

Product Registration

For more efficient customer service and to activate the product’s warranty, Targus recommends that you register your Targus accessory shortly after purchasing it.
To register your Targus accessory, go to:
http://www.targus.com/registration.asp (English) – or – http://www.japan.targus.com/customer_registration.asp (Japanese)
You will need to provide your full name, email address, phone number, and company information (if applicable).

Warranty

Targus warrants this product to be free from defects in materials and workmanship for one year. If your Targus accessory is found to be defective within that time,
we will promptly repair or replace it. This warranty does not cover accidental damage, wear and tear, or consequential or incidental loss. Under no conditions is
Targus liable for loss of, or damage to a computer; nor loss of, or damage to, programs, records, or data; nor any consequential or incidental damages, even if
Targus has been informed of their possibility. This warranty does not affect your statutory rights.
Warranty Registration at:
http://www.targus.com/registration.asp

Regulatory Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.

FCC Statement

Tested to Comply

This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and
if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Move the computer away from the receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

All trademarks are the property of their respective owners.

Belgium [phone] Spain [phone]

Denmark [phone] Sweden [phone]

France [phone] Switzerland [phone]

Germany [phone] United Kingdom [phone]

Italy [phone] Eastern Europe &

others

[phone]

Netherlands [phone]

400-0085-001A