Targus ACP076US Quick Start Manual

Targus wants to ensure you get the best performance
from your Docking Station. Laptops usually ship with
outdated drivers, updating these drivers will optimize
the performance of your Docking Station.

Visit this website www.targus.com/us/usb3/setup
and we will guide you through updating the:

Laptop USB 3.0 Host Controller Driver
Laptop Video Card Driver
DisplayLink™ Video and Ethernet Driver

1

2

3

Features and specications are subject to change without notice. Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries.

All trademarks and registered trademarks are the property of their respective owners. ©2014 Targus Group International, Inc.

IMPORTANT: DO NOT connect

the Docking Station until you have
updated the drivers on your laptop.

410-2872-001D (ACP76US / AU)

QUICK START GUIDE

UNIVERSAL USB 3.0

SV DOCKING STATION

Contents

· Targus Universal USB 3.0 SV Docking Station

· USB 3.0 cable

· AC power adapter with input cable

· DVI-I to VGA adapter

Specifications

· 1 x DVI-I port

· 3 x USB 3.0 ports

· Ports marked with supports BC 1.2 and iOS device charging (1.5A)

· Gigabit Ethernet

· Audio In/Out ports

· Security lock slot

· 5V 4A AC adapter

· USB 3.0 cable

Technical Support

For technical questions, please visit:

· US

Internet: www.targus.com/support.asp

Telephone: [phone]

· Australia

Internet: www.targus.com/au

Email: [e-mail]

Telephone: [phone]

· New Zealand

Telephone: [phone]

Three years warranty

1. Targus warrants to the original purchaser that its products are free from defects in materials and workmanship for

three years. This warranty is limited to defects, materials and workmanship. 2. The benefits to the consumer given by

the warranty are in addition to other rights and remedies of the consumer under law in relation to the goods to which

the warranty relates. 3. The warranty is given by (i) Targus Australia, (ii) Targus Australia’s business address is: 117-

119 Bowden Street, Meadowbank, NSW 2114 Australia, (iii) Targus Australia’s telephone number is 1800 641 645,

Email: [e-mail] (iv) To make a warranty claim for goods purchased in New Zealand, the telephone number

is: 0800 633 222, or the goods may be returned to the supplier in New Zealand. 4. What the purchaser must do to

entitle the purchaser to claim warranty:- (i) The purchaser must call the telephone number for Australia or New Zealand

set out above, (ii) The purchaser must provide the purchaser’s name, daytime contact number, business hours delivery

address, the Targus model number on the product, date and place of purchase with receipt for purchase if required,

and describe the fault condition. 5. What Targus must do:- (i) Targus will provide the purchaser with store return

information or a return authorisation so that the purchaser may return the product for warranty inspection, (ii) If after

inspection Targus finds the product is defective in materials or workmanship, Targus shall replace (or repair) the

defective product at the discretion of Targus and ship the product from Targus warehouse at its expense within three

business days (Monday to Friday excluding public holidays) of receiving the returned goods. If the product is no longer

available Targus reserves the right to replace with the nearest corresponding product of no lesser quality, (iii) Targus

will bear the cost of return delivery to the purchaser regardless of the inspection test result. The purchaser must bear

the cost of the delivery to Targus. There is no charge for inspection. 6. Our goods come with guarantees that cannot

be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and

for compensation for any other reasonable foreseeable loss or damage. You are also entitled to have the goods

repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

7. Please note: (i) Features and specifications of all Targus products are subject to change without notification, (ii) In

some instances: Goods presented for repair may be replaced by refurbished goods of the same type rather than being

repaired. Refurbished parts may be used to repair the goods, (iii) If goods accepted for repair retain user-generated

data: During the process of repair some or all of your stored data may be lost. Please ensure that you have saved this

data elsewhere prior to repair.

Regulatory Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) This device must accept any interference received, including

interference that may cause undesired operations.

Declaration of Conformity

Hereby, Targus declares that this device is in compliance with the essential requirements and other relevant provisions

of Directive 2004/108/EC.

System Requirements

Hardware

· PC with an Intel

®

Pentium

®

processor or equivalent

· USB port

· AC power outlet

Operating System (any of the following)

· Microsoft Windows

®

7 or Windows

®

8 or Windows

®

8.1 (32/64-bit)

· Mac OS

®

X v10.6.8, 10.7.5, or 10.8.3

· Mac OS

®

X v10.6.8 or later

FCC Statement (Tested to Comply)

This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following measures:

· Reorient or relocate the receiving antenna

· Increase the separation between the equipment and receiver

· Connect the equipment into an outlet on a circuit different from the one that the receiver is connected

· Consult the dealer or an experienced radio/TV technician for help

Changes or modifications not authorized by the party responsible for compliance could void the user’s authority to

operate this product.

DisplayLink Manager Menu

MEN U OPTION FUNCTION

DisplayLink Manager Opens the Screen Resolution window

Check for Updates

Checks online if new drivers are available to
download

DisplayLink Devices Shows a list of all connected DisplayLink devices

Audio Setup Opens the Audio Configuration window

Video Setup Opens the Screen Resolution window

Screen Resolution

Shows a list of all available screen resolutions
(Inferred Modes are not available in mirror mode)

Screen Rotation

Rotates the screen in clockwise or counter-clockwise
directions

Extend Extends the Windows desktop onto this display

Set as Main Monitor Sets this screen as the main display

Notebook Monitor Off

Switches off the laptop display and uses the DisplayLink
display as the main screen (works only on PCs and
when one DisplayLink screen is connected)

Mirror

Shows the same content on both screens (screen
resolutions must be the same)

Off Turns off the DisplayLink display

Optimize for Video

Select for improved video playback on DisplayLink
connected displays (only applicable for video; text
may appear less clear)

Fit to TV

Adjusts the size of the Windows desktop to fit the
connected TV (only works when one DisplayLink
display is connected and set in Extend Mode)

To Set the Display into Extend Mode

1

Click on the DisplayLink icon

2

Select Extend in Manager Menu

The device is now extended in the direction it was the last time the display was
in this mode. For more control, use the Extend To submenu and select one of the
options. This puts the device into Extend Mode, and places it to the Left/Right/
Above/Below the main monitor.

To Set the Display into Mirror Mode

1

Click on the DisplayLink icon

2

Select Mirror in Manager Menu

The resolution, color depth and refresh rate of the primary screen are replicated on
the monitor connected to the docking station.

Fit to TV Configuration

Windows® 7 or 8 or 8.1 Setup

IMPORTANT: DO NOT connect the docking station prior

to updating the drivers on your laptop (see front page of this
guide to update drivers)

2

A red border on the

DisplayLink screen
shows the size of
the new Windows
desktop. Use the
+ and - controls to
change the size of
the red border until
it fits the TV screen.

1

To configure Fit to TV,
choose the option
from the DisplayLink
Manager. The following
interface appears:

3

Once the red border

is at the edges of
the TV screen, click
“Apply” to resize the
Windows desktop.

Gigabit

Ethernet

Audio Out

USB 3.0 Port

USB 3.0 Ports

DVI-IPower In

USB to

Laptop Port

Audio In

Detachable base, slides on/off.

To detach the base,
insert paper clip here

Docking Station Diagram

1

Connect all peripheral devices to the docking

station, including the power adapter

2

Connect the Docking Station to your laptop

+

3

Windows will start installing the DisplayLink Driver

automatically

4

Follow the on-screen instructions until the
installation is complete

1 2