Tannoy CMS-801 sub Owners manual
CMS801 sub
Product Description
The Tannoy CMS801 subwoofer is a compact unit is specifically designed to complement
the full range CMS ceiling monitor systems; delivering low frequency extension into
applications that require a combination of premium sonic quality and output level for music
and speech reinforcement.
The 200mm (8.00") driver, with long throw multi fibre paper pulp cone, and a 2nd order
160Hz passive crossover are mounted in a vented, injection moulded, paintable front baffle
manufactured from UV/weather resistant UL94V-0 ABS material.
Two CMS801 subwoofer model versions and a separate back can are available to satisfy
the vast majority of installation application requirements:
CMS801 sub BM (Blind Mount) - supplied with an integral back can.
CMS801 sub PI (Pre-Install) - supplied without a back can.
CMS801 PI Back Can (Pre-Install back can) - use with the CMS801 sub PI.
The CMS801 sub BM model is equipped with a low insertion loss 60W line transformer
mounted within the back can. This is easily configurable to the following settings via front
baffle mounted rotary tapping switch:
70V systems: 60W / 30W / 15W / 7.5W / OFF & low Impedance operation
100V systems: 60W / 30W / 15W / OFF & low Impedance operation
The CMS801 sub PI is supplied without a transformer. If the product is to be used without a
back can a 60W line transformer (7600 1658) is available as an optional accessory for easy
connection to the baffle mounted control switch circuit. Installing the transformer in this
manner (flying) requires installation in accordance with local building regulations.
NOTE: For optimum performance and full compliance with safety ratings Tannoy
recommends using the CMS801 PI back can (8001 4570) accessory option in which the
transformer is pre-fitted.
The zinc plated steel back cans have an integrated, recessed termination box. The
removable locking connector has screw terminals for secure wire termination and "loop
through" facility. Strain relief is provided by a clamping mechanism for use with plenum
rated cable or conduit.
Features
• High Power & high sensitivity with low distortion
• UV/weather resistant UL94V-0 ABS front baffle
• Blind Mount & Pre Install options
• Easily accessible tapping switch on front baffle
• Low insertion loss 60W line transformer
• Packaged with tile rails and C-ring for quick &
easy installation and simple stocking logistics
• Five year warranty
Applications
• Multizone foreground music and paging systems
• Boardrooms and offices
• Business music systems
• Airports, convention centres, hotels
• Reception and waiting rooms
• Houses of worship
• Retail outlets and shopping malls
• Lounges and bars
• Cruise ships
• Courtrooms
Spring loaded self-aligning clamps make for quick and easy installation, while all models
are also supplied with two tile support rails and one C-ring included in the package.
A plaster (mud) ring is available as an optional accessory.
Tannoy United Kingdom
Tannoy North America
Tannoy Deutschland
Tannoy France
Tannoy adopts a policy of continuous improvement and product specification is subject to change
T: 00 44 (0) 1236 420199
T: 00 1 (519) 745 1158
T: 00 49 (180) 1111 881
T: 00 33 (0)1 7036 7473
E: enquiries@tannoy.com
E: inquiries@tannoyna.com
E: info@tannoy.com
E: ventes@tannoy.com
CMS801 BM / PI sub data file // issue 1.06 // 14.01.08
CMS801 sub
TECHNICAL SPECIFICATIONS
System CMS801 sub
1)
requency response (-3dB)
F
Frequency range (-10dB)
ystem sensitivity (1W @1m)
S
Crossover Integral 2nd order passive,
ated maximum SPL
R
Average 112dB
Peak 118dB
verage with THP60 110dB
A
Power handling
(3)
Average 100W
rogramme 200W
P
eak 400W
P
Recommended amplifier power 200W @ 8 Ohms
Nominal Impedance 8 Ohms
Transformer taps
(via front rotary switch)
70V 60W / 30W / 15W / 7.5W / OFF
100V 60W / 30W / 15W / OFF
Distortion
10% Full Power (7.75V) 2nd Harmonic 3rd Harmonic
70Hz 1.22% 1.90%
100Hz 0.38% 0.49%
1% Full Power (2.45V) 2nd Harmonic 3rd Harmonic
70Hz 0.91% 1.28%
100Hz 0.04% 0.44%
Notes
(1)
Average over stated Bandwidth. Measured in an IEC baffle in an Anechoic Chamber
(2)
Unweighted pink noise input, measured in an IEC baffle in an Anechoic Chamber.
If the loudspeaker is placed in the ceiling near a corner ( /
in sensitivity and maximum SPL can be realised.
(3)
Long term power handling capacity as defined in EIA - 426B test
A full range of measurements, performance data, and Ease™ Data can be
downloaded from www.tannoy.com
Tannoy operates a policy of continuous research and development. The introduction
of new materials or manufacturing methods will always equal or exceed the
published specifications, which Tannoy reserves the right to alter without prior
notice. Please verify the latest specifications when dealing with critical applications.
(
8Hz - 160Hz
5
(1)
42Hz - 300Hz
(2)
2dB (1W = 2.45V for 8 Ohms)
9
60 Hz
1
(
2)
& Low Impedance operation
& Low Impedance operation
) an increase of 6dB
2
Transducer
1x 200mm (8.00") long throw woofer with
multi fibre paper pulp cone
Physical
Enclosure
Back can Zinc plated steel
Baffle Reflex loaded UL 94V-0 rated ABS
rille Steel, with weather resistant coating
G
afety features Safety ring located at rear of enclosure
S
Clamping design Security toggle clamp
ack can options
B
lind Mount (BM) Complete with fixed back can
B
re Install (PI) Separate back can for Pre Installation
P
Cable entry options Cable clamp & squeeze connector for
Conduit knockouts 3 Sets of horizontal positions
Connectors Removable locking connector with screw
Safety agency ratings
(pending) UL-1480, UL-2043, CE
BM Hole cutout diameter 295mm (11.61")
PI Hole cutout diameter 295mm (11.61")
Dimensions
Bezel diameter 325mm (12.80")
Front of ceiling to
rear of back can (BM) 310.5mm (12.22")
Front of ceiling to
top of safety loop (BM) 327.8mm (12.90")
Front of ceiling to rear
of speaker unit (PI) 117.50mm (4.63")
Front of accessory back can
bezel to top of safety loop (PI) 168.5mm (6.63")
Net weight (ea)
CMS801 sub BM 6.3kg (13.89lbs)
CMS801 sub PI 3.2kg (7.05lbs)
PI Back can 4kg (8.81lbs)
Included accessories C Ring, tile bridge, paint mask,
Optional accessories Plaster (Mud) Ring
for load bearing safety bond
conduit up to 22mm
19 / 22 / 28mm (0.75 / 0.87 / 1.1")
terminals with "loop through" facility
cutout template, grille
Ordering information
Part number Packed Weight
8001 4730 CMS801 sub BM White 2 19.0 (41.89)
8001 4740 CMS801 sub PI White 2 11.5 (25.35)
8001 4650 Plaster Ring - CMS801 N/A 10 8.0 (17.64)
8001 4570 Back can CMS801 PI 8 Ohm N/A 1 4.5 (9.92)
7600 1658 CMS 60 Watt XFMR/Lead Dual 8 Ohm N/A 10 12.0 (26.46)
Tannoy United Kingdom
Tannoy North America
Tannoy Deutschland
Tannoy France
Tannoy adopts a policy of continuous improvement and product specification is subject to change
Model name
T: 00 44 (0) 1236 420199
T: 00 1 (519) 745 1158
T: 00 49 (180) 1111 881
T: 00 33 (0)1 7036 7473
Colour
Packed QuantityBaffle / Grille
E: enquiries@tannoy.com
E: inquiries@tannoyna.com
E: info@tannoy.com
E: ventes@tannoy.com
CMS801 BM / PI sub data file // issue 1.06 // 14.01.08
kg (lbs)
50
6
0
7
0
80
9
0
1
00
0
000
1
0
00
1
0
01
01
0
10
2
0
30
40
50
0
0
01
0
01
011
NECHOIC
A
FREQUENCY
RESPONSE
CMS801 sub
PERFORMANCE MEASUREMENTS
m on-axis frequency response
1
SPL, 1W/1m (dB)
frequency (Hz)
1m on-axis frequency response
Impedance (ohms)
frequency (Hz)
IMPEDANCE
Tannoy United Kingdom
Tannoy North America
Tannoy Deutschland
Tannoy France
Tannoy adopts a policy of continuous improvement and product specification is subject to change
T: 00 44 (0) 1236 420199
T: 00 1 (519) 745 1158
T: 00 49 (180) 1111 881
T: 00 33 (0)1 7036 7473
E: enquiries@tannoy.com
E: inquiries@tannoyna.com
E: info@tannoy.com
E: ventes@tannoy.com
CMS801 BM / PI sub data file // issue 1.06 // 14.01.08
Loading...