Tannoy CMS-501-DC Owners manual

CMS501 DC
Product Description
The Tannoy CMS501 DC is a full bandwidth; high power and high sensitivity ceiling monitor system. The 130mm (5.00") Tannoy Dual ConcentricTM is a point source drive unit design comprising a multi fibre paper pulp mid bass cone and a 19mm (0.75") ferrofluid cooled, titanium dome HF unit with neodymium magnet system. The driver and passive frequency dividing network are mounted in a vented, injection moulded, paintable front baffle manufactured from UV/weather resistant UL94V-0 ABS material.
The mid-bass and tweeter sections of the Tannoy Dual ConcentricTM constant directivity driver are coincidentally aligned to a true point source; ensuring a wide and controlled dispersion for optimum coverage; this while avoiding the massive loss of energy in the vertical plane, at the crossover frequency, inherent in two-way discreet designs. This high power and high sensitivity design, with extended frequency response and very low distortion, is equipped with dynamic high frequency protection.
This compact unit is specifically designed for applications requiring the combination of premium sonic quality for music and speech reinforcement with exceptional reliability and intelligibility.
The CMS501 DC is equipped with a low insertion loss 30W line transformer easily configurable to the following settings via front baffle mounted rotary tapping switch:
70V systems: 30W / 15W / 7.5W / 3.75W / OFF & low Impedance operation 100V systems: 30W / 15W / 7.5W / OFF & low Impedance operation
Two CMS501 DC model versions and a separate back can are available to satisfy the vast majority of installation application requirements:
CMS501 DC BM (Blind Mount) - supplied with an integral back can. CMS501 DC PI (Pre-Install) - supplied without a back can. CMS501 PI Back Can (Pre-wire back can) - use with the CMS 501 DC PI.
The zinc plated steel back cans have an integrated, recessed termination box. The removable locking connector has screw terminals for secure wire termination and "loop through" facility. Strain relief is provided by a clamping mechanism for use with plenum rated cable or conduit.
Spring loaded self-aligning clamps make for quick and easy installation, while all models are also supplied with two tile support rails and one C-ring included in the package. A plaster (mud) ring is available as an optional accessory.
Features
• 130mm (5.00") point source Dual ConcentricTM Driver
• High power & high sensitivity with extended frequency
response and very low distortion
• Wide, controlled constant directivity dispersion for
optimum coverage.
• Does not suffer from massive loss of energy in the
vertical plane at crossover caused by two way
discreet designs
• UV/weather resistant UL94V-0 ABS front baffle
• Blind Mount & Pre Install options
• Dynamic high frequency protection
• Easily accessible tapping switch on front baffle.
• Low insertion loss 30W line transformer
• Ferrofluid cooled neodymium HF
• Packaged with tile rails and C-ring for quick & easy
installation and simple stocking logistics
Applications
• Multi-zone foreground music & paging systems
• Multi-zone foreground music & paging systems
• Boardrooms & offices
• Business music systems
• Airports, convention centres, hotels
• Reception and waiting rooms
• Houses of worship
• Retail outlets and shopping malls
• Lounges and bars
• Cruise ships
• Courtrooms
Tannoy United Kingdom Tannoy North America Tannoy Deutschland Tannoy France
Tannoy adopts a policy of continuous improvement and product specification is subject to change
T: 00 44 (0) 1236 420199 T: 00 1 (519) 745 1158 T: 00 49 (180) 1111 881 T: 00 33 (0)1 7036 7473
E: enquiries@tannoy.com E: inquiries@tannoyna.com E: anfragen@tannoy.com E: ventes@tannoy.com
CMS501 DC data file // issue 1.06 // 10.01.08
CMS501 DC
TECHNICAL SPECIFICATIONS
System CMS501 DC
1)
requency Response (-3dB)
F
M Back can
B
Frequency Range (-10dB)
M Back can
B
Frequency Range (-10dB)
I Back can
P
System Sensitivity (1W @1m)
ominal Coverage Angle 90 degrees conical
N
Coverage Angle (1kHz to 6kHz) 109 degrees conical
Directivity Factor (Q) 5.9 averaged 1kHz to 6kHz
Directivity Index (DI) 6.9 averaged 1kHz to 6kHz
Rated Maximum SPL
Average 107dB Peak 113dB
ower Handling
P
Average 60W
rogramme 120W
P Peak 240W
Recommended Amplifier Power 120W @ 8 Ohms
Nominal Impedance 8 Ohms
Transformer Taps (via front rotary switch) 70V 30W / 15W / 7.5W / 3.75W / OFF
100V 30W / 15W / 7.5W / OFF
Distortion 10% Full Power 2nd Harmonic 3rd Harmonic
250Hz 2.91% 0.1% 1kHz 0.18% 0.9% 10kHz 0.79% 0.14%
1% Full Power 2nd Harmonic 3rd Harmonic 250Hz 0.5% 0.07% 1kHz 0.25% 0.32% 10kHz 0.45% 0.07%
Crossover
(1) Average over stated bandwidth. Measured at 1 metre on axis. (2) Unweighted pink noise input, measured at 1 metre in an anechoic chamber (3) Long term power handling capacity as defined in EIA - 426B test
A full range of measurements, performance data, CLF and Ease™ Data can be downloaded from www.tannoy.com
Full independent verification of published specifications carried out by NWAA Labs, California can also be obtained from the downloads section of www.tannoy.com
Tannoy operates a policy of continuous research and development. The introduction of new materials or manufacturing methods will always equal or exceed the published specifications, which Tannoy reserves the right to alter without prior notice. Please verify the latest specifications when dealing with critical applications.
(
5Hz - 50kHz
8
(1)
74Hz - 54kHz
(1)
70Hz - 54kHz
(2)
89dB (1W = 2.83V for 8 Ohms)
(2)
& Low Impedance operation
& Low Impedance operation
2kHz - 2nd order LF, 2nd order HF (with dynamic HF protection)
Transducers
ow Frequency 130mm (5.00") Dual Concentric™ constant
L
igh Frequency 19mm (0.75") titanium dome with
H
eodymium magnet system
n
irectivity driver with multi fibre paper
d
ulp cone
p
Physical
Enclosure
Back can Zinc plated steel
affle Reflex loaded UL 94V-0 rated ABS
B
rille Steel, with weather resistant coating
G
Safety Features Safety ring located at rear of enclosure
Clamping Design Security toggle clamp
Min / Max Clamping Range 0.0mm (0.0") / 20.0mm (0.79") Recommended Clamp Torque 1.5Nm
Back Can Options
Blind Mount (BM) Complete with fixed back can
re Install (PI) Separate back can for pre installation
P
Cable Entry Options Cable clamp and squeeze connector for
Conduit Knockouts 3 Sets of horizontal positions
Connectors Removable locking connector with screw
Safety Agency Ratings
BM Hole Cutout Diameter 190mm (7.48")
PI Hole Cutout Diameter 190mm (7.48")
Dimensions
Bezel diameter 210mm (8.27")
Front of ceiling to rear of back can (BM) 189.5mm (7.46")
Front of ceiling to top of safety loop (BM) 206.80mm (8.14")
Front of ceiling surface to rear of speaker unit (PI) 135.60mm (5.34")
Front of accessory back can bezel to top of safety loop (PI) 153.50mm (6.04")
Net Weight (ea) CMS501 DC BM 3.90kg (8.60lbs) CMS501 DC PI 2.90kg (6.39lbs) CMS501 DC PI back can 2.60kg (5.73lbs)
Included Accessories C Ring, tile bridge, paint mask,
Optional Accessories Plaster (Mud) Ring
for load bearing safety bond
conduit up to 22mm
19 / 22 / 28mm (0.75" / 0.87" / 1.10")
terminals with "loop through" facility
(pending) UL-1480, UL-2043, CE
cutout template, grille
Ordering Information
PART NUMBER PACKED QUANTITYBAFFLE / GRILLE COLOURMODEL NAME
8001 4450 CMS501 BM White / paintable 2 8001 4460 CMS501 PI White / paintable 2 8001 4180 CMS501 Plaster (Mud) Ring Zinc plated steel 10 8001 3830 CMS501 PI back can Zinc plated steel 1
Tannoy United Kingdom Tannoy North America Tannoy Deutschland Tannoy France
Tannoy adopts a policy of continuous improvement and product specification is subject to change
T: 00 44 (0) 1236 420199 T: 00 1 (519) 745 1158 T: 00 49 (180) 1111 881 T: 00 33 (0)1 7036 7473
E: enquiries@tannoy.com E: inquiries@tannoyna.com E: anfragen@tannoy.com E: ventes@tannoy.com
CMS501 DC data file // issue 1.06 // 10.01.08
CMS501 DC
DI
1
10
100
100 1000 10000
0
30
6
0
90
1
20
150
1
80
2
10
240
2
70
3
00
330
360
100 1000 10000
0
10
20
30
40
50
6
0
7
0
1 10 100 1000 10000 100000
5
0
60
7
0
80
9
0
100
10 100 1000 10000 100000
PERFORMANCE MEASUREMENTS
m on-axis frequency response
1
ANECHOIC FREQUENCY
ESPONSE
R
IMPEDANCE
OFF AXIS RESPONSE
SPL, 1W/1m (dB)
frequency (Hz)
Impedance vs frequency
Impedance (ohms)Level (dB)
frequency (Hz)
frequency (Hz)
Horizontal off-axis response
BEAMWIDTH
DIRECTIVITY INDEX
Tannoy United Kingdom Tannoy North America Tannoy Deutschland Tannoy France
Tannoy adopts a policy of continuous improvement and product specification is subject to change
T: 00 44 (0) 1236 420199 T: 00 1 (519) 745 1158 T: 00 49 (180) 1111 881 T: 00 33 (0)1 7036 7473
E: enquiries@tannoy.com E: inquiries@tannoyna.com E: anfragen@tannoy.com E: ventes@tannoy.com
Horizontal off-axis response
frequency (Hz)
frequency (Hz)
CMS501 DC data file // issue 1.06 // 10.01.08
Loading...
+ 6 hidden pages