Tannoy CMS501 User Manual

CMS501
Product Description
The Tannoy CMS501 is a full bandwidth; high power and high sensitivity ceiling monitor system. The design comprises a 130mm (5.00") transducer mounted in a vented, injection moulded, paintable front baffle manufactured from UV/weather resistant UL94V-0 ABS material.
The point source configuration of the Tannoy ICTTM driver •s mid-bass and tweeter sections ensures a wide and controlled dispersion for optimum coverage; this while avoiding the massive loss of energy in the vertical plane, at the crossover frequency, inherent in two-way discrete designs. The ICTTM (Inductive Coupling Technology) drive unit also addresses the two most common component failures experienced in background music and sound reinforcement systems, the tweeter and the crossover reliability. The use of a wireless electromagnetic tweeter means that no crossover is required in the design; this therefore ensures that an ICTTM unit is exceptionally reliable and therefore ideal for applications where constant heavy usage is the norm. This aluminium high frequency dome has a deep drawn skirt that sits on the inside of the low frequency voice coil in the same magnetic gap. The skirt is like a single shorted turn that is induced with high frequency information generated by the low frequency voice coil, which is fed a full bandwidth signal. The mineral loaded polypropylene cone material and nitrile rubber surround further enhance durability and long-term reliability.
This compact unit is specifically designed for applications requiring the combination of premium sonic quality for music and speech reinforcement and exceptional reliability.
The CMS501 is equipped with a low insertion loss 30W line transformer easily configurable to the following settings via front baffle mounted rotary tapping switch:
70V systems: 30W / 15W / 7.5W / 3.75W / OFF & low Impedance operation 100V systems: 30W / 15W / 7.5W / OFF & low Impedance operation
Two CMS501 model versions and a separate back can are available to satisfy the vast majority of installation application requirements:
CMS501 BM (Blind Mount) - supplied with an integral back can. CMS501 PI (Pre-Install) - supplied without a back can. CMS501 PI Back Can (Pre-wire back can) - use with the CMS 501 PI.
The zinc plated steel back cans have an integrated, recessed termination box. The removable locking connector has screw terminals for secure wire termination and "loop through" facility. Strain relief is provided by a clamping mechanism for use with plenum rated cable or conduit.
Spring loaded self-aligning clamps make for quick and easy installation, while all models are also supplied with two tile support rails and one C-ring included in the package. A plaster (mud) ring is available as an optional accessory.
Features
130mm (5.00") ICTTM transducer for greater durability
and longevity
High power and high sensitivity with extended
frequency response
Wide, controlled constant directivity dispersion for
optimum coverage.
Does not suffer from massive loss of energy in the
vertical plane at crossover caused by two way
discreet designs
UV/weather resistant UL94V-0 ABS front baffle
Blind Mount and Pre Install options
No crossover required
Easily accessible tapping switch on front baffle.
Low insertion loss 30W line transformer
Packaged with tile rails and C-ring for quick and easy
installation and simple stocking logistics
Five year warranty
Applications
Multi-zone foreground music & paging systems
Boardrooms and offices
Business music systems
Airports, convention centres, hotels
Reception and waiting rooms
Houses of worship
Retail outlets and shopping malls
Lounges and bars
Cruise ships
Courtrooms
Tannoy United Kingdom Tannoy North America Tannoy Deutschland Tannoy France
Tannoy adopts a policy of continuous improvement and product specification is subject to change
T: 00 44 (0) 1236 420199 T: 00 1 (519) 745 1158 T: 00 49 (180) 1111 881 T: 00 33 (0)1 7036 7473
E: enquiries@tannoy.com E: inquiries@tannoyna.com E: anfragen@tannoy.com E: ventes@tannoy.com
CMS501 data file // issue 1.06 // 10.01.08
CMS501
TECHNICAL SPECIFICATIONS
System CMS501
1)
requency Response (-3dB)
F
M Back can
B
Frequency Range (-10dB)
M Back can
B
Frequency Range (-10dB)
I Back can
P
System Sensitivity (1W @1m)
ominal Coverage Angle 90 degrees conical
N
Coverage Angle (1kHz to 6kHz) 105 degrees
Directivity Factor (Q) 5.6 averaged 1kHz to 6kHz
Directivity Index (DI) 7.0 averaged 1kHz to 6kHz
Rated Maximum SPL
Average 106dB Peak 112dB
ower Handling
P
Average 50W
rogramme 100W
P Peak 200W
Recommended Amplifier Power 100W @ 6 Ohms
Nominal Impedance 6 Ohms
Transformer Taps (via front rotary switch) 70V 30W / 15W / 7.5W / 3.75W / OFF
100V 30W / 15W / 7.5W / OFF
Distortion 10% Full Power 2nd Harmonic 3rd Harmonic
250Hz 2.81% 0.14% 1kHz 0.5% 0.25% 10kHz 1.77% 0.04%
1% Full Power 2nd Harmonic 3rd Harmonic 250Hz 0.18% 0.09% 1kHz 0.16% 0.22% 10kHz 0.32% 0.09%
Crossover 7kHz inductively coupled
(1) Average over stated bandwidth. Measured at 1 metre on axis. (2) Unweighted pink noise input, measured at 1 metre in an anechoic chamber (3) Long term power handling capacity as defined in EIA - 426B test
A full range of measurements, performance data, CLF and Ease™ Data can be downloaded from www.tannoy.com
Full independent verification of published specifications carried out by NWAA Labs, California can also be obtained from the downloads section of www.tannoy.com
Tannoy operates a policy of continuous research and development. The introduction of new materials or manufacturing methods will always equal or exceed the published specifications, which Tannoy reserves the right to alter without prior notice. Please verify the latest specifications when dealing with critical applications.
(
5Hz - 22kHz
8
(1)
74Hz - 24kHz
(1)
74Hz - 24kHz
(2)
89dB (1W = 2.45V for 6 Ohms)
(2)
& Low Impedance operation
& Low Impedance operation
Transducers
Low Frequency 130mm (5.00") mineral loaded
High Frequency ICT™ aluminium dome
polypropylene ICT™
Physical
Enclosure
Back can Zinc plated steel Baffle Reflex loaded UL 94V-0 rated ABS Grille Steel, with weather resistant coating
afety Features Safety ring located at rear of enclosure
S
Clamping Design Security toggle clamp
Min / Max Clamping Range 0.0mm (0.0") / 20.0mm (0.79") Recommended Clamp Torque 1.5Nm
ack Can Options
B
lind Mount (BM) Complete with fixed back can
B Pre Install (PI) Separate back can for pre installation
Cable Entry Options Cable clamp and squeeze connector for
Conduit Knockouts 3 Sets of horizontal positions
Connectors Removable locking connector with screw
Safety Agency Ratings
BM Hole Cutout Diameter 190mm (7.48")
PI Hole Cutout Diameter 190mm (7.48")
Dimensions
Bezel diameter 210mm (8.27")
Front of ceiling to rear of back can (BM) 189.5mm (7.46")
Front of ceiling to top of safety loop (BM) 206.8mm (8.14")
Front of ceiling surface to rear of speaker unit (PI) 135.6mm (5.34")
Front of accessory back can bezel to top of safety loop (PI) 153.50mm (6.04")
Net Weight (ea) CMS501 BM 3.60kg (7.94lbs) CMS501 PI 2.90kg (6.39lbs) PI back can 2.60kg (5.73lbs)
Included Accessories C Ring, tile bridge, paint mask,
Optional Accessories Plaster (Mud) Ring
or load bearing safety bond
f
conduit up to 22mm
19 / 22 / 28mm (0.75" / 0.87" / 1.10")
terminals with "loop through" facility
(pending) UL-1480, UL-2043, CE
cutout template, grille
Ordering Information
PART NUMBER PACKED QUANTITYBAFFLE / GRILLE COLOURMODEL NAME
8001 4450 CMS501 BM White / paintable 2 8001 4460 CMS501 PI White / paintable 2 8001 4180 CMS501 Plaster (Mud) Ring Zinc plated steel 10 8001 3830 CMS501 PI back can Zinc plated steel 1
Tannoy United Kingdom Tannoy North America Tannoy Deutschland Tannoy France
Tannoy adopts a policy of continuous improvement and product specification is subject to change
T: 00 44 (0) 1236 420199 T: 00 1 (519) 745 1158 T: 00 49 (180) 1111 881 T: 00 33 (0)1 7036 7473
E: enquiries@tannoy.com E: inquiries@tannoyna.com E: anfragen@tannoy.com E: ventes@tannoy.com
CMS501 data file // issue 1.06 // 10.01.08
CMS501
DI
1
10
100
100 1000 10000
50
60
7
0
80
9
0
1
00
110
10 100 1000 10000 100000
0
5
10
15
20
25
1 10 100 1000 10000 100000
50
60
70
80
90
100
110
10 100 1000 10000 100000
0 deg
10 deg
20deg
3
0deg
4
0deg
Beamwidth (1/3 Octave)
0
30
60
9
0
120
1
50
180
210
240
270
300
3
30
3
60
100 1000 10000
PERFORMANCE MEASUREMENTS
m on-axis frequency response
1
ANECHOIC FREQUENCY
ESPONSE
R
IMPEDANCE
OFF AXIS RESPONSE
SPL, 1W/1m (dB)
frequency (Hz)
Impedance vs frequency
Impedance (ohms)Level (dB)
frequency (Hz)
frequency (Hz)
Horizontal off-axis response
BEAMWIDTH
DIRECTIVITY INDEX
Tannoy United Kingdom Tannoy North America Tannoy Deutschland Tannoy France
Tannoy adopts a policy of continuous improvement and product specification is subject to change
T: 00 44 (0) 1236 420199 T: 00 1 (519) 745 1158 T: 00 49 (180) 1111 881 T: 00 33 (0)1 7036 7473
frequency (Hz)
Horizontal off-axis response
frequency (Hz)
E: enquiries@tannoy.com E: inquiries@tannoyna.com E: anfragen@tannoy.com E: ventes@tannoy.com
CMS501 data file // issue 1.06 // 10.01.08
Loading...
+ 6 hidden pages