Tait TEL0055, TEL0054, TEL0052 Installation guide

12 T2000 Installation Guide

CORPORATE HEAD OFFICE

NEW ZEALAND

Tait Electronics Ltd

P.O. Box 1645, Christchurch

Phone : (64) (3) 358-3399 Fax : (64) (3) 358-0340

AUSTRALIA

Tait Electronics (Aust) Pty Ltd

Phone : (61) (7) 3865-7799 Fax : (61) (7) 3865-7990

Toll Free : (1-300) 304-344

E-mail: [e-mail]

CANADA

Tait Mobile Radio Inc

Phone : (1) [phone] Fax : (1) [phone]

Toll Free : (1) 1-800-890-8248

E-mail: [e-mail]

Tait Latin Americ a

Phone : (1) [phone] Fax : (1) [phone]

E-mail: [e-mail]

NEW ZEALAND

Tait Communications Ltd

Phone : (64) (3) 348-3301 Fax : (64) (3) 343-0558

E-mail: [e-mail]

USA

Tait Electronics (USA) Inc

Phone : (1) [phone] Fax : (1) [phone]

Toll Free : (1-800) 222-1255

E-mail: [e-mail]

TAIT EUROPE

Regional Head Office

UNITED KINGDOM

Tait Europe Ltd

Phone : (44) (1480) 52255 Fax : (44) (1480) 411-996

E-mail: [e-mail]

FRANCE

Tait France S.A.R.L.

Phone : (33) (1) 41-14-05-50 Fax : (33) (1) 41-14-05-55

E-mail: [e-mail]

GERMANY

German Office

Phone : (49) (911) 2870-7064/7160

Fax : (49) (911) 2870-7077

E-mail: [e-mail]

TAIT NORTH ASIA

Regional Head Office

HONG KONG

Tait Mobile Radio (Hong Kong) Ltd

E-mail: [e-mail]

Phone : [phone] Fax : [phone]

BEIJING

Tait Mobile Radio (Hong Kong) Ltd

Phone : [phone] Fax : [phone]

E-mail: [e-mail]

TAIWA N

Tait Mobile Radio (Taiwan) Ltd

Phone : [phone] Fax : [phone]

E-mail: [e-mail]

TAIT SOUTH EAST ASIA

Regional Head Office

SINGAPORE

Tait Electronics (Far East) Pte Ltd

Phone : [phone] Fax : [phone]

E-mail: [e-mail]

THAILAND

Tait Mobile Radio Ltd

Phone : [phone] Fax : [phone]

E-mail: [e-mail] m

Excellence in

Radio Communications

T2000 Installation Guide

T2000

Installation Guide

2 T2000 Installation Guide

T2000 Installation Guide 11

3. Route the cable as required, fitting grommets where necessary to prevent chafing of the cable
insulation.

4. Fit the red connector to the printed circuit board socket – the connector is shaped so that it can be
fitted in the correct orientation only.

5. Refit the cable to the cable clamp on the rear cover and slip the two nuts into the receptacles at
each end of the rear cover.

6. Refit the rear cover and replace the cover screws, tightening them carefully. Do not overtighten
the screws.

The control head can now be installed as follows:

1. Mount the bracket for the control panel on a flat surface using the self-tapping screws supplied.

2. Place the control head in the bracket, position it for a good viewing angle, and fit the 2 screws to
secure it in place.

Microphone Clip

The microphone clip must be earthed (to the negative supply line) if hookswitch control of monitor­ing, scanning or call termination is to operate. Refer to the radio’s operating instructions to confirm
requirements.

Ensure that the microphone clip is mounted in a position where the microphone PTT key cannot be
inadvertently activated or jammed on.

Installation Checks

1. Plug the microphone into the socket on the lower left-hand corner of the radio’s front

2. Insert the fuses into the power lead.

3. Switch on the radio and confirm that it is operational.

4. Connect an in-line power meter between the radio and the antenna and measure the forward
and reflected power levels. Less than 1W should be reflected for 25W forward power. If this is
not achieved, check the installation - including antenna length.

5. Make a call to another party on the radio (as described in the operating instructions).

Tait Electronics has made every effort to ensure the accuracy of information in this manual. However, Tait
Electronics reserves the right to update the radio and/or this manual without notice.