System Sensor RTS151KEYA Installation Instructions Manual

INSTALLATION AND MAINTENANCE INSTRUCTIONS

* Sup. contacts cannot be used if they are wired to control panel.

RTS151KEYA

6581 Kitimat Road, Unit 6, Mississauga, Ontario L5N-3T5

1-800-SENSOR2, FAX: [phone]

Remote Test Station

www.systemsensor.ca

SPECIFICATIONS

Dimensions: 4.6˝ H × 2.75˝ W × 1.8˝ D

Weight: 0.24 Lbs.

Power Requirements

Power LED (Green): 14 – 35 VDC, 12 mA maximum
Alarm LED (Red): 2.8 – 32 VDC, 12 mA maximum
Alarm Response Time: 40 seconds maximum
Temperature: –10°C to 60°C (14°F to 140°F)
Humidity: 95% relative humidity, noncondensing Max

NOTE: RTS151KEYA replaces RTS451KEYA.

FIGURE 1. RTS151KEYA

NOTICE: This manual shall be left with the owner/user of this equipment.
NOTE: A test coil is required only for use with D2A,DNRA,DH400A,DH500A
models. For D2A models order part # DCOIL. For DH400A/500A models
order part #Coil.

GENERAL INFORMATION

The System Sensor RTS151KEYA is an automatic fire detector accessory
designed to test remotely located duct and beam detectors. For 4-wire detec­tors, the RTS151KEYA features a multi-colored LED that alternates between

OFF

RESET TEST

steady green and red. Green indicates power and that the detector board is
in place. Red indicates alarm. For 2-wire detectors, the LED will show red for
alarm. Consult the detector installation instructions for additional information.

The National Fire Protection Association and CAN/ULC-S536 has published
codes, standards, and recommended practices for the installation and use
of this product. It is recommended that the installer be familiar with these re­quirements, with local codes, and any special requirements of the local au­thority having jurisdiction.

RTS151KEYA CONTENTS

1 RTS151KEYA remote test station

1 screw pack (2 mounting screws)

2 Keys

OPERATION
Test Function

FIGURE 2: WIRING DIAGRAM FOR RTS151KEYA TO D4120A
4-WIRE DUCT SMOKE DETECTOR:

RTS151KEYA

FIELD
INSTALLED
JUMPER

2

4

D4120A

AUX OUT +

AUX OUT –

H0195-01

Insert the key and turn clockwise to the “TEST” position.

EXTERNAL

*

(-) POWER (+)

SUPPLY

ALARM

R TEST

R RESET

*

SUP, NO

SUP, C

4 5

321

RTS151KEYA

REMOTE TEST STATION

LED OPTION

1 PER UNIT

10mA CURRENT DRAW

TEST COIL OPTION

1 PER UNIT

95mA CURRENT DRAW

H0582-13

H0571-10

Alarm Indication

With the key in the “TEST” position, some time will elapse (40 seconds maxi­mum) depending on the detector type, before the alarm indicating LED will
turn red.

Reset Function

Turn the key counterclockwise to the “RESET” position and hold. The LED
should turn off. Then, turn the key back to the “NORMAL” position and re­move. The RTS151KEYA is capable of resetting only certain models of detec­tors. Refer to the detector installation instructions for additional information.

Wiring Instructions

Consult the appropriate detector installation instructions for the applicable
wiring diagram. The RTS151KEYA mounts to a single gang box (2 1/2˝ mini­mum depth), or directly to the wall or ceiling.

In Canadian applications, the RTS151KEYA is intended to be located in the
same room as the smoke detector and within 60 feet of the unit.

(RED LED)

ALARM

(GREEN LED)

POWER

1

5

3

6

FIGURE 3: WIRING DIAGRAM FOR RTS151KEYA TO D2A 2-WIRE
DUCT SMOKE DETECTOR:

TEST COIL +

TEST COIL –

COMM +

OUT (CONV ONLY) +

COMM –

RA/RTS –

RA +

RTS +

NOTE: THE RTS151KEYA TEST COIL
CIRCUIT REQUIRES AN EXTERNAL 24 VDC
POWER SUPPLY WHICH MUST BE UL LISTED.

NOTE: THE USE OF A REMOTE TEST STATION REQUIRES THE
INSTALLATION OF AN ACCESSORY COIL, PART NUMBER DCOIL,
SOLD SEPARATELY.

D440-03-00 1 I56-3475-000

FIGURE 4: WIRING DIAGRAM FOR RTS151KEYA TO DNRA 2-WIRE DUCT SMOKE DETECTOR:

1

2

3

4

5

6

3

4

5

Test +

Test / Reset –

Reset +

Test

Reset

RA +

RA –

V Out +

DH100

RTS151KEYA

6

2

1

Alarm

LED

No Connection

MAGNET
TEST
SWITCH

ALARM
LED (RED)

4

5

2

(–)

(+)

1

RTS151KEYA

(OPTIONAL) REMOTE

TEST STATION

+ TEST COIL

– TEST COIL

+ IN

+ OUT

–

– RA

+ RA

+ RTS

24 VDC

AUX POWER

(–)

SUPPLIED

BY USER

(+)

(100mA

SUPPLY)

24 VAC (+10%, –15%)

FULL WAVE RECTIFIED,

UNFILTERED POWER

MAY BE USED

DNRA

METHOD #1 - AUX POWER LOCATED

AT DUCT DETECTOR

NOTE: THE USE OF THE RTS151KEYA REQUIRES THE INSTALLATION OF

AN ACCESSORY COIL, DCOIL, SOLD SEPARATELY.

FIGURE 5. WIRING DIAGRAM FOR RTS151KEYA TO DH100ACDC
4-WIRE DUCT SMOKE DETECTOR:

DH100ACDCLPA

Alarm Signal

Aux. Power +

Sup. N. O.

Sup. COM

Aux. Power –

Reset

Test

15

19

14

3

20

2

11

RTS151KEYA

(Red LED) Alarm

1

* Sup. contacts
cannot
be used if they are
wired to control
panel.

(Green LED)

6

Power

2

3

4

5

*

24 VDC

AUX POWER

SUPPLIED

BY USER

(100mA

SUPPLY)

24 VAC (+10%, –15%)

FULL WAVE RECTIFIED,

UNFILTERED POWER

MAY BE USED

MAGNET
TEST
SWITCH

ALARM
LED (RED)

4

5

2

(–)

(+)

1

RTS151KEYA

(OPTIONAL) REMOTE

TEST STATION

+ TEST COIL

– TEST COIL

+ IN

+ OUT

–

– RA

+ RA

+ RTS

DNRA

METHOD #2 - AUX POWER LOCATED

AT TEST STATION

H0612-10

FIGURE 6. WIRING DIAGRAM FOR RTS151KEYA TO DH100 2-WIRE
DUCT SMOKE DETECTOR:

NOTE: Terminal 6 of the RTS151KEYA is not used when wired to a 2-wire detector.

FIGURE 7. WIRING DIAGRAM FOR RTS151KEYA TO DH400ACDCA
DUCT SMOKE DETECTOR:

DH400ACDCA

1

6

2

3

4

5

Alarm Signal

Aux. Power +

Sup. N. O.

Sup. COM

Aux. Power –

System Sensor warrants its enclosed product to be free from defects in materials and
workmanship under normal use and service for a period of three years from date of
manufacture. System Sensor makes no other express warranty for the enclosed prod­uct. No agent, representative, dealer, or employee of the Company has the authority to
increase or alter the obligations or limitations of this Warranty. The Company’s obliga­tion of this Warranty shall be limited to the replacement of any part of the product which
is found to be defective in materials or workmanship under normal use and service
during the three year period commencing with the date of manufacture. After phoning
System Sensor’s toll free number 800-SENSOR2 (736-7672) for a Return Authorization

Reset

Test

5

7

11

10

6

3

4

number, send defective units postage prepaid to: System Sensor, Returns Department,

D440-03-00 2 I56-3475-000
©2009 System Sensor

RTS151KEYA

(Red LED) Alarm

* Sup. contacts
cannot be used if
they are wired to
control panel.

(Green LED)
Power

H0156-08

FIGURE 8. WIRING DIAGRAM FOR RTS151KEYA TO BEAM1224A/
BEAM1224SA SMOKE DETECTOR:

*

H0156-09

REMOTE ALARM OUT

REMOTE TROUBLE OUTPUT

NOTE: RTS151KEYA CAN BE USED WITH INTELLIGENT BEAM DETECTOR PRODUCTS.
CONSULT INTELLIGENT BEAM DETECTOR MANUAL FOR ADDITIONAL INSTRUCTIONS

Three-Year Limited Warranty

RA #__________, 6581 Kitimat Road, Unit 6, Mississauga, Ontario L5N-3T5. Please
include a note describing the malfunction and suspected cause of failure. The Company
shall not be obligated to replace units which are found to be defective because of dam­age, unreasonable use, modifications, or alterations occurring after the date of manufac­ture. In no case shall the Company be liable for any consequential or incidental damages
for breach of this or any other Warranty, expressed or implied whatsoever, even if the
loss or damage is caused by the Company’s negligence or fault. Some states do not
allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. This Warranty gives you specific legal rights,
and you may also have other rights which vary from state to state.

AUX (–)

RESET INPUT

TEST INPUT

T2-1

T2-2

T2-4

T3-3

OPTIONAL YELLOW LED

T2-3

RTS151KEYABEAM1224A/BEAM1224SA

(RED LED) ALARM

1

2

3

4

5

H0193-05

RESET

TEST

H0585-04