System Sensor CZ-6 User Manual

INSTALLATION AND MAINTENANCE INSTRUCTIONS

CZ-6 Six Zone Interface Module

SPECIFICATIONS

Normal Operating Voltage: 15-32 VDC
Stand-By Current: 2 mA
Alarm Current: 40 mA (assumes all six LEDs solid on)
Temperature Range: 32°F to 120°F (0°C to 49°C)
Humidity: 10 to 93% Non-condensing
Dimensions: 6.8˝H x 5.8
Accessories: CH-6 Chassis; BB-2 Cabinet; BB-6 Cabinet
Wire Gauge: 12-18 AWG
Maximum IDC Wiring Resistance: 25 Ohms
External Power Supply Voltage: Regulated 24VDC
Ripple Voltage: 0.1 volts RMS maximum
IDC (supervised and power limited)
DC Voltage: 18-28 volts power limited
Frequency: DC
Current: 90mA per circuit

˝W x 1.25˝D

I56-1799-005

3825 Ohio Avenue, St. Charles, Illinois 60174

800/736-7672, FAX: [phone]

www.systemsensor.com

BEFORE INSTALLING

This information is included as a quick reference installation
guide. Refer to the appropriate control panel installation manual
for detailed system information. If the modules will be installed in
an existing operational system, inform the operator and local au­thority that the system will be temporarily out of service. Discon­nect the power to the control panel before installing the modules.
This system contains static sensitive components. Always ground
yourself with a proper wrist strap before handling any circuits so
that static charges are removed from the body. The module hous­ing should also be grounded.

NOTICE: This manual should be left with the owner/user of
this equipment.

GENERAL DESCRIPTION

The CZ-6 Six Zone Interface Module is intended for use in an
intelligent alarm system. Each module provides an interface be­tween the intelligent alarm system and a conventional alarm sys­tem loop. A common SLC input is used for all modules, and the
initiating device loops share a common supervisory supply and
ground. Otherwise, each monitor operates independently from the
others. Each module has its own unique address.

A pair of rotary code switches is used to set the address of the first
module from 01 to 94. The remaining modules are automatically
assigned to the next five higher addresses. Provisions are included
for disabling a maximum of two unused modules to release the
addresses to be used elsewhere. Each module also has panel con­trolled bicolor LED indicators. The panel can cause the LEDs to
blink, latch on, or latch off.

Compatible Two-wire System Sensor Smoke Detectors for use with CZ-6 with Zone Identifier A

DET. DETECTOR
MODEL COMP. ID MANUFACTURER BASE MODEL MAX DET.

1151 A SYSTEM SENSOR B110LP, B401 20
1451 A SYSTEM SENSOR B401, B401B 20
1451DH A SYSTEM SENSOR DH400 20
2151 A SYSTEM SENSOR B110LP, B401 20
2451 A SYSTEM SENSOR DH400, B401B, B401 20
2451TH A SYSTEM SENSOR B401, B401B 20
5451 A SYSTEM SENSOR B401 20
1100 A SYSTEM SENSOR N/A 20
1400 A SYSTEM SENSOR N/A 20
** 2100AT A SYSTEM SENSOR N/A 20
2100B A SYSTEM SENSOR N/A 20
2100D A SYSTEM SENSOR N/A 20
2100S A SYSTEM SENSOR N/A 20
2100TB A SYSTEM SENSOR N/A 20
2100TD A SYSTEM SENSOR N/A 20
2100TS A SYSTEM SENSOR N/A 20
2300B A SYSTEM SENSOR N/A 20
2300TB A SYSTEM SENSOR N/A 20
2400 A SYSTEM SENSOR N/A 20
2400TH A SYSTEM SENSOR N/A 20
* 2W-B A SYSTEM SENSOR N/A 20
* 2W-TB A SYSTEM SENSOR N/A 20
DH100LP A SYSTEM SENSOR N/A 20
* Class B, Style B only
** No Accessory will be supported by 2100AT

D500-49-00 1 I56-1799-005

Backbox
Mounting
Holes

Mount with self-threading screws

to back of cabinet

2

3

1

Included:

0

1

2

3

4

5

6
7
8

9

0

7
8

6

5

4

3

2

1

9
1
0

11

1
2

1
3

1
4

15

BASE

ADDRESS

ADDRESS

DISABLE

N
O
N
E

O
N
E

T
W
O

T
H
R
E
E

0

1

2

3

4

5

6
7
8

9

0

7
8

6

5

4

3

2

1

9
1
0

1
1

1
2

1
3

1
4

1
5

BASE

ADDRESS

ADDRESS

DISABLE

NONE

ONE

TW
O

THREE

(5) 1 x 4 Terminal Blocks (2) 1

1

/4” Stand offs (3) Shunts

(4) Machine Screws (2) Nuts (1) Long Power Supply Jumper

(6) 3.9k Ohm
End of Line Resistors

Shipped on Board:

C0202-00

(2) Shunts in Class A/B position
(Shipped in Class B position, remove shunts for Class A)

COMPATIBILITY REQUIREMENTS

To ensure proper operation, this module shall be connected to a
compatible system control panel. Contact System Sensor for a list
of compatible detectors.

COMPONENTS

Following are descriptions of the CZ-6 mounting frameworks.
There are two mounting options for CZ-6 modules:

• Up to six CZ-6 modules can be installed on a CH-6 in a BB-6 cabinet

• One or two CZ-6 modules can be installed in a BB-2 cabinet

Chassis

The CH-6 chassis is used to mount CZ-6 modules in a BB-6, cabi­net. It accommodates up to six CZ-6 modules in a single cabinet
row three modules wide and two modules deep.

Figure 1. CH-6 Chassis:

Cabinets

A BB-6 cabinet will house the CH-6 chassis with up to six CZ-6
modules installed on it. Refer to cabinet installation documents
for dimensions.

The BB-2 cabinet houses one or two CZ-6 modules on the internal
chassis that is part of the cabinet. Refer to cabinet installation
documents for dimensions.

INSTALLATION STEPS

1. Cabinet Mounting

In a clean, dry area, mount the backbox using the four holes

provided in the back surface of the cabinet (Figure 3).

2. Chassis Installation

The CH-6 chassis is mounted in the BB-6 cabinet. It is shipped

with two self-threading screws, which are used to fasten the
chassis to the back wall of the cabinet. (Figure 4).

Figure 3. Typical mounting hole locations:

C0235-00

Figure 4. Mounting the CH-6 chassis:

The BB-2 cabinet comes with the chassis already installed, so
no mounting is necessary.

C0206-00

The BB-2 cabinet has a built-in chassis that will accommodate
one or two CZ-6 modules.

Figure 2: BB-2 Cabinet

3. Module Installation

There are two methods for installing a module in the rear posi

tion of a chassis. Method one is for installation of a rear mod­ule only, when no module will be installed in front of it. Refer
to Figure 5 for instructions. Method two is for installation of
a rear module when another module will be installed in the
chassis position in front of it. Refer to Figures 6a and 6b for
method two. All necessary screws and standoffs are supplied
with the modules.

Figure 5. Installation of rear module only, method one:

The front CZ-6 module positions of each chassis are offset below the rear
CZ-6 module positions so that all of the status indicators are visible.

D500-49-00 2 I56-1799-005

C0234-00

C0236-00

-

C0237-00