Symmons S-254 Service Manual
Symmetrix
Lavatory Faucet S-254 Series
Installation and Service Instructions
INSTALLATION:
Caution: Be sure to turn o hot and cold water supplies
before installing or servicing faucet.
1.
Push valve bodies through holes in sink from underneath. Make
sure mounting nuts (RT-103N) are on underside of sink. Valve
marked Hot is on the le and Cold is on the right. Put gasket
(LN-129) over valve body. read escutcheon (LN-128) onto valve
bodies. e top of the valve spindle should measure 1-7/8” from
mounting surface (See rough in drawing).
2. read collar (LN-112 or LN-111) on to valve body until it reaches the
escutcheon (LN-128). Tighten mounting nuts from underneath sink.
3. Standard or LWG handle installation: Place bushing (LN-115) on
valve spindle. Turn valves to o position (CR style: turn clockwise;
LWG, LCF, LPO, LAM, and standard style: turn hot clockwise,
turn cold counterclockwise). Place handle (LN-131) on bushing.
read screw (LN-146 or LN-121) into valve and push plug button
(T-33R and T-33B) into top of handle. CR, LCF, LPO and LAM
handle installation: Place lever part of handle on valve spindle and
thread screw (LN-121 or LN-134) into valve.
4. Swivel spout option: Place spout assembly (LN-200) in centerbody
(LN-197). read nut (LN-199) onto centerbody (LN-197).
Rigid spout option: read screw (LN-205) into the bottom of the
spout assembly (LN-200). Place spout assembly (LN-200) in center
body (LN-197). read nut (LN-199) onto center body (LN-197).
5. Drop assembled center body and spout through center hole of deck.
Secure assembly to sink using nut (SPF-26) and washer (LN-138).
6. read adapter (LN-189) onto the end of the center body (LN-197).
read ex hoses (LN-157) into center body using pipe dope or te on
tape on the pipe threads. read ex hoses (LN-157) into center body.
read other end to valve bodies. Note: e adapter can be backed o
a full turn to allow better positioning on the ex hoses.
7. Connect hot supply to le tube and cold supply to right tube using
appropriate connectors.
8. It is very important to thoroughly ush the supply lines to prevent
foreign matter, i.e. copper chips, sand, stones, etc. from damaging
the sealing surfaces of cartridge. Remove aerator and open hot and
cold to full open then open both supplies. Let water run through
hot and cold long enough to ush supply lines thoroughly. Shut o
faucet and replace aerator. Check for leaks.
Cartridge Replacement (KN-113 or KN-114):
1. Remove plug button (T-33, T-33R or T-33B), loosen Philip head
screw (LN-121) and remove handle, (LN-131 or LN 152).
2. Remove collars (LN-112) by turning counter clockwise, do not use
wrench as this may damage the surface nish.
3. Place wrench on cartridge hex nut (KN-113, KN-114). Turn
wrench counter clockwise until cartridge is removed.
4. Install new cartridge. Turn cartridge with wrench until cartridge
does not turn easily then turn 1/4 to 1/2 turn further. Reassemble
handle in reverse fashion.
®
Dimensions Symmetrix, S-254, S-254-CR, S-254-LAM, S-254-LPO, S-254-LCF, S-254-LTM
S-254
standard
handle shown
Escutcheon
S-254-LAM
S-254-LPO
S-254-LCF
S-254-LTM
1-1/16" (27mm) min
1-7/16" (37mm) max
hole size
7/8" (22mm) min
1-3/8" (35mm) max
hole size
S-254-CR handle
Note: Dimensions subject to
change without notice.
DF-30 Finial, lever, handle (2)
KN-113 Valve cartridge, cold
KN-114 Valve cartridge, hot
KN-120 O-ring (2)
L-5 Aerator
L-5NA Aerator (laminar)
L-5VP Aerator (vandal-resistant)
L-42 Nut (2)
LN-111 Lock ring (2)
LN-112 Collar (lever handle) (2)
LN-115 Bushing (2)
LN-121 Philips pan head screw (2)
LN-128 Escutcheon, valve (2)
LN-129 Gasket, escutcheon (2)
LN-131 ADA handle (2)
LN-133A Temperature indicator (red)
LN-133B Temperature indicator (blue)
LN-134 Oval Philips head screw (2)
LN-138 Washer
LN-140 Lever handle (2)
LN-142 Valve body (HOT)
LN-142A Valve body (COLD)
LN-149 Clear, Lever, Handle (2)
LN-150 O-ring
LN-152 Lever, Handle (2)
LN-153A White, Lever, Handle (2)
LN-153B Chrome, Lever, Handle (2)
LN-157 Flex hose (2)
LN-177 Cross handle (2)
LN-189 Adapter
LN-197 Center body
LN-199 Nut
LN-200 Spout
LN-205 Anti-rotation pin
LN-218 O-ring
P-26 Grid drain assembly (complete)
RT-103N Nut Flanged
SPF-26 Nut, Hex
T-33B Plug Button, Blue
T-33R Plug Button, Hot
LN-200
L-5
L-5NA
L-5VP
T-33
T-33B
T-33R
LN-121
LN-140
LN-111
LN-115
LN-128
LN-129
KN-114
RT-103N
LN-142
L-42
LN-157
P-26
LN-218
KN-120
LN-205
LN-199
LN-129
KN-113
LN-197
LN-150
LN-138
SPF-26
LN-189
LN-142A
Handle option: LPO, LAM, LCF
LN-134
LN-152
LN-133A, LN-133B
LN-153A, LN-153B
LN-149
LN-112
LN-128
DF-30
Handle option: LWG
T-33
T-33B, T-33R
LN-121
LN-131
LN-111
LN-115
Handle option: CR
T-33
T-33B, T-33R
LN-121
LN-177
LN-112
LN-128
KN-114
Cartridge used for both
hot and cold handles
NOTE: Two LN-142 Valve bodies are
used in conjunction with this handle.
Aerator
(ow regulator)
Part Number
Standard Vandal Resistant
Aerator with removal tool
2.2 gpm (8.3L/min) SWA-17FR SWA-17VP
1.5 gpm (5.7L/min) FLR-111-1.5 ----
Ordering replacement parts:
Call Symmons customer service at (800) 796-6667,
(781) 848-2250 M-F 8:00 am - 7:30 pm EST or
check our website at www.symmons.com for a
list of Symmons distributors.
1.0 gpm (3.8L/min) FLR-111-1.0 --- .5 gpm (1.9L/min) LL-60B ----
Removal tool part number, LL-60K
Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184
(800) 796-6667, (781) 848-2250
Website: www.symmons.com
©2007, 2008 Symmons Industries, Inc. Printed in U.S.A.
■ Fax (800) 961-9621, (781) 664-1300
■ Email: customerservice@symmons.com
■ ZV-418 ■ 043009
Loading...