Symmons S-250-0 Service Manual

Symmetrix

Lavatory Faucet S-250 Series

Installation and Service Instructions

Caution: Be sure to turn off hot and cold water supplies before
installing or servicing faucet.

Installation

1. Push faucet supplies with rubber gasket through holes

in sink (make sure gasket [LL-126] is between faucet
and sink). Secure faucet to sink by tightening  ange
nuts (LL-125) from underside. (If sink or counter
surface is uneven, use putty or sealant to make proper
seal under base.)

2. Connect hot supply to le tube and cold supply to

right tube using appropriate connectors.

3. Pop-up drain installation:

a) Remove pop-up plug, tail piece and  ange from the

drain body. Make sure that locknut is threaded all
the way down onto the body with  at friction washer
in middle and beveled washer on top.

b) Apply plumbers putty or sealant to bottom of  ange.

c) Install drain body through drain opening in lava-

tory and screw  ange onto the drain body making
sure that the threads are completely engaged for
proper sealing and strength of the connection.
Apply joint compound to all threaded parts to
insure proper seal.

d) Tighten locknut to compress the beveled  ange

evenly across the bottom of the drain opening taking
care not to over tighten the locknut, causing damage
to the lavatory.

e) Remove one of two ball washers from inside the

threaded cavity. Insert pop-up plug and pivot rod
into body. Add one ball washer (the second ball
washer should remain inside the body) to the
outside of the ball. Tighten the retaining nut until
the ball is seated on the internal and external ball
washers. Note:  e pop-up plug can be installed
either in the removable or non-removable position,
depending on the location of the hole located in the
guide at the bottom of the plug.

f) Slide the pivot rod through one side of the spring

clip, then the appropriate adjustment hole and then
other side of the spring clip.

g) Insert li rod through faucet housing and the top of

the li strap and secure it in place by tightening the
screw. Note: To insure proper operation of li rod
and pop-up, some adjustment of the linkage may be
required.  ere are two possible adjustment points:

1) li strap to li rod and 2) li strap to pivot rod.

4. It is very important to thoroughly  ush the supply

lines to prevent foreign matter, i.e. copper chips, sand,
stones, etc. from damaging the sealing surfaces of car­tridge. Remove aerator and open hot and cold to full
open then open both supplies. Let water run through
hot and cold long enough to  ush supply lines thor­oughly. Shut o faucet and replace aerator. Check for

leaks.

Replacing handle

1. Remove screw from top of handle. Remove red or blue

washer and then remove handle (LL-122) or (LL-123).

2. Reassemble handle (LL-122) or (LL-123) in reverse

fashion.

Replacing cartridge

1. Remove screw from top of handle. Remove red or blue

washer and then remove handle (LL-122) or (LL-123).

2. Unthread cartridge cover (LL-127) from faucet.

3. Place wrench on cartridge (LL-124) hex nut, turn

wrench counter clockwise until cartridge is removed.

4. Install new cartridge (LL-124). Turn cartridge with

wrench until cartridge does not turn easily then turn
1/4 to 1/2 turn further.

5. Reassemble cartridge cover (LL-127).

6. Reassemble (LL-122) or (LL-123) handle in reverse

fashion.

®

S-250-1

S-250-1-LWG

Dimensions Symmetrix Lavatory Faucet, S-250 Series

Note: Dimensions subject to

change without notice.

Parts Assembly Symmetrix Lavatory Faucet, S-250 Series

Lever handle

repair kit

LL-122

Cartridge cover

LL-127

Vandal proof

aerator and

removal tool

Wing handle
repair kit

LL-123

Cartridge (2)
LL-124

Gasket

LL-126

Flange nut (2)

LL-125

Nut (2)

L-42

Aerator

(ow regulator)

2.2 gpm (8.3L/min) LN-15* LN-101

1.5 gpm (5.7L/min) FLR-111-1.5

1.0 gpm (3.8L/min) FLR-111-1.0
.5 gpm (1.9L/min) ---- LN-100

Removal tool part number, LL-60K

Note: When ordering replacements parts for

*

faucets with an optional decorative nish, append
appropriate three letter nish sufx code to part
numbers marked with an asterisk (

Ordering replacement parts:

Call Symmons customer service at [phone],
[phone] M-F 8:00 am - 7:30 pm EST or
check our website at www.symmons.com for a
list of Symmons distributors.

Part Number
Standard Vandal Resistant

Aerator with removal tool

*
*
*

----

----

*

).

*

Pop-up Drain Assembly

P-25LR

Grid Drain Assembly

P-26

Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184
[phone], [phone]
Website: www.symmons.com

©2002, 2005, 2008 Symmons Industries, Inc. Printed in U.S.A.

■ Fax [phone]

■ Email: [e-mail]

■ ZV-420 ■ 043009