Symmons S-245 Service Manual

Symmetrix

®

Bar Sink and Lavatory Faucet, S-245 & 249 Series

Installation and Service Instructions

INSTALLATION:

Caution: Be sure to turn off hot and cold water supplies
before installing or servicing faucet.

1. Align flat edge of escutcheon showing logo with the back of sink.
Insert faucet supplies through holes in sink. Secure faucet to sink
by tightening flange nuts (KN-116) from underside. (If sink or
counter surface is uneven, use putty or sealant to make proper
seal under base.)

2. Connect hot supply to left tube and cold supply to right tube using
appropriate connectors.

3. It is very important to thoroughly flush the supply lines to

prevent foreign matter, i.e. copper chips, sand, stones, etc.
from damaging the sealing surfaces of cartridge. Remove

aerator (bar faucet) and turn cold valve handle on to full cold posi­tion, open cold supply. Without closing, turn hot valve handle to
full hot position and open hot supply. Let water run in hot only and
cold only positions long enough to flush supply lines thoroughly.
Shut off faucet and replace aerator. Check for leaks.

Cartridge Replacement

Faucets with standard LCT handles

1. Remove plug button (T-33, T-33R or T-33B), loosen philip head screw
(LN-121A) and remove handle (LN-140, LN-131 or LN-102).

2. Place wrench on cartridge hex nut (KN-113, KN-114). Turn wrench
counter clockwise until cartridge is removed.

3. Install new cartridge. Turn cartridge with wrench until cartridge does
not turn easily then turn 1/4 or 1/2 turn further. Reassemble handle
in reverse fashion.

Faucets with optional LCF, LPO or LAM handles:

1. Loosen philip oval head screw (LN-134) and remove handle (LN-152).

2. Remove collar (LN-112) by turning counter clockwise, do not use
wrench as this may damage the surface finish.

3. Place wrench on cartridge hex nut (KN-113, KN-114). Turn wrench
counter clockwise until cartridge is removed.

4. Install new cartridge. Turn cartridge with wrench until cartridge does
not turn easily then 1/4 or 1/2 turn further. Reassemble handle in
reverse fashion.

To lock spout:

1. See instructions in lock (BL-114) package.

S-249 with
std LCT handles

S-245 with
std LCThandles

Dimensions Symmetrix

S-245-5
Long spout

S-245,
standard spout

2-13/16"

71 mm

1/2"-14 NPSM

®

Bar Sink Faucet, S-245 and S-245-5

12-3/8"
314mm

3-3/8"
85mm

8"

203 mm

2-1/4"

57 mm

2"

51mm

4"

102mm

5-15/16"

152 mm

1-3/8" max
35 mm

Note: Dimensions subject to
change without notice.

5-1/2"

140 mm

3-1/2"

89 mm

9-1/8"

232 mm

6-13/16"

174 mm

2-1/8"

54 mm

BL-102 Tubing assembly
BL-104* Escutcheon
BL-105* Nut, spout
BL-107* Spout (S-245 Series)
BL-106 Spout (S-249 Series)
BL-108 O-ring
BL-109 Adaptor, 3/4" hose (S-249 Series)
BL-113* Spout (S-245-5 Series)
BL-114 Spout lock
DF-30* Finial, lever, Handle (2)
KN-113 Valve cartridge, cold
KN-114 Valve cartridge, hot
KN-116 Flange nut (2)
L-42 Nut (2)
LN-20 Gasket
LN-102 Acrylic handle (2)
LN-111* Lock ring (2)
LN-112* Collar (lever handle) (2)
LN-115 Bushing (2)
LN-121A Philips pan head screw (2)
LN-131 ADA handle (2)
LN-133A Temperature indicator (red)
LN-133B Temperature indicator (blue)
LN-134* Oval Philips head screw (2)
LN-140* Lever handle (2)
LN-147B Snap ring
LN-149 Clear, Lever, Handle (2)
LN-152* Handle lever
LN-153A White, Lever, Handle (2)
LN-153B Chrome, Lever, Handle (2)
J-21 O-ring
T-33* Plug Button (2)
T-33B Plug Button, Blue
T-33R Plug Button, Hot

*

For Decorative Finish Faucets (S-245 Series
only) add sufx to parts marked with an asterisk
as follows:
Sufx -STN: Radiance® satin nish

Parts Assembly

Symmetrix Lavatory / Bar Sink Faucet, S-245 & S-249

KN-114

J-21

L-5

LN-134

DF-30

LN-112

LN-152

LN-133A, LN-133B

LN-153A, LN-153B
LN-149

Handle option: LPO, LAM, LCF

Handle option: LCT

T-33, T-33B, T-33R

LN-121A

LN-102

KN-114

Cartridge used for
both hot and cold handles

BL-106

BL-109

* LN-111 not used with this handle
* LN-115 not used with this handle

L-5

BL-113

L-5

T-33
T-33B
T-33R

LN-121A

LN-140

BL-107

LN-115

KN-113

BL-105

LN-111

LN-147B

BL-108

BL-104

BL-114

BL-102

LN-20

KN-116

L-42

T-33, T-33B, T-33R

LN-121A

LN-131

Handle option: LWG

Part Number
Standard Vandal Resistant

Aerator with removal tool

Removal tool part number, LL-60K

Aerator
(ow regulator)

2.2 gpm (8.3L/min) SWA-17FR SWA-17VP

1.5 gpm (5.7L/min) FLR-111-1.5 ----

1.0 gpm (3.8L/min) FLR-111-1.0 ---­ .5 gpm (1.9L/min) ---- LL-60B

Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184
Phone: [phone] ■ Fax: [phone]
Website: www.symmons.com ■ Email: [e-mail]

©2007-2014 Symmons Industries, Inc. Printed in U.S.A. ■ ZV-366 ■ Rev A ■ 100314