Symmons Origins S-9610-1.5, Origins S-9612-1.5 Maintenance Manual

Origins

IAPMO R&T

S-9610-1.5, S-9612-1.5

Single Handle Centerset Lavatory Faucet

Operation & Maintenance Manual

®

Model Numbers

S-9610-1.5



Origins Single Handle Centerset Lavatory Faucet
Less Rod

S-9612-1.5



Origins Single Handle Centerset Lavatory Faucet

Modifications

-0.5 0.5 gpm (1.9 L/min) aerator






Note: Append appropriate -sufx to model number.

CG

-1.0 1.0 gpm (3.8 L/min) aerator

CG

-G Grid drain

-STN Satin Nickel finish

Compliance

-NSF/ANSI 372, NSF/ANSI 61.9

-ASME A112.18.1/CSA B125.1

-WaterSense 1.5 gpm & 1.0 gpm

c

Certied by

Specification

Single handle centerset lavatory faucet featuring a
4” mounting conguration. Includes ceramic cartridge,
15 3/4” stainless steel braided hoses with 3/8”
compression ttings, 50/50 drain assembly and standard

1.5 gpm (5.7 L/min) aerator. Components made from metal
and nonmetallic materials plated in standard polished
chrome nish.

Warranty

Limited Lifetime - to the original end purchaser in

consumer/residential installations.
5 Years - for industrial/commercial installations.
Refer to www.symmons.com/warranty for complete
warranty information.

WARNING: This product can expose you to chemicals
including lead, which is known to the state of California to
cause cancer, birth defects, or other reproductive harm.
For more information, go to www.P65Warnings.ca.gov.

Dimensions

AA
BB

CC

DD

KK

EE

LL LL

FF

GG

Note: Dimensions subject to change without notice.

HH

Measurements

II

JJ

A 5 7/8", 149 mm
B 3 3/4", 95 mm
C 5 1/4", 133 mm
D 3 1/2", 89 mm

E
F 3/8" Compression Fitting

G

H

I
J
K 2", 51 mm
L 1/4", 6 mm

Deck Thickness Ref.

Max. 1 1/8", 29 mm

Hole Size

Min. Ø 1 3/8", 35 mm

(2x) Hole Size

Min. Ø 1 1/4", 32 mm

4 1/4", 108 mm
Min. 2", 51 mm

Parts Breakdown

A

E

B

D

C

Replacement Parts

Item Description Part Number

A
B
C

Handle Kit RL-226*

N1

N2

F

F Lift Rod RL-225*

G

G Cartridge RL-227

H

I

I Aerator

J

J
L

M

Mounting Hardware RL-228

RL-239-1.5* (1.5)
RL-239-1.0* (1.0)
RL-239-0.5* (0.5)

K

RL-223*

(S-9612-1.5)

P-26*

(S-9610-1.5)

N14

N13

M

L

N 50/50 Drain Assembly

O Grid Drain

*Note: Append -STN to part number for Satin Nickel

nish.

Tools Required

Adjustable wrench

N9

N11

N12

N10

N3

N4

N5

N6

N8

N7

N

Allen wrench (3/32”)

Plumber putty

Plumber tape

O

2

1

1

2

3

4

4

N12

N9

N13

2

N14

N13

1

F

Installation

If replacing an older faucet
ensure water supply is turned
OFF before removing, then
turn faucet control valve ON to
relieve water pressure.

1) Insert hoses from faucet body
(H) and threaded rods (J) through
mounting gasket (K) and sink
holes.

H

J

3) Seat ange (N2) into sink (N3
gasket optional). Install gasket
(N4), washer (N5) and nut (N6)
onto ange (N2) from below sink,
but do not secure nut. Screw on
tail piece (N7) and hand tighten.

PLUMBER

PUTTY

N2

N3

OPTIONAL

2

N4

N5

N6

N7

3

5) Attach inner washer (N8), pivot rod
(N9) and outer washer (N10) to tail­piece (N7). Hand tighten nut (N11)
to secure pivot rod (N9).

N11

N10

1

N8

N7

N9

6) Connect lift rod (F) to clevis strap
(N13) and secure with thumb
screw (N14). Insert pivot rod
(N9) through spring clip (N12)
and clevis strap (N13). Secure
with spring clip (N12) and adjust
linkage if necessary.

K

2) Place brackets (L) onto threaded
rods (J). Secure with nuts (M).

J

L

M

2

4) Turn tail piece (N7) and ange
(N2) so pivot is facing toward
faucet. Pull assembly down into
drain hole. Secure hardware from
below sink. Install stopper (N1) in
the removable or non-removable
position.

3

N1

N2

2

N7

PIVOT

3

1

5

5

1

Installation

I

1

4

7) Attach supply lines to shut-off
valves and hand tighten. Using a
wrench, nish with one-half turn.
DO NOT overtighten.

1

1

Maintenance

8) Remove aerator (I) and ush lines
free of debris. Check for leaks.

9) Adjust limit stop washer to limit
handle turn to the hot position if
desirable.

2

2

Note: Counterclockwise to lower
temperature, clockwise to increase
temperature.

1) Turn off water supply. Remove
plug button (A). Loosen and
remove the handle set screw (B),
handle (C), collar (D) and nut (E).

4

C

6

D

7

E

A

3

B

2) Remove old cartridge. Correctly
align new cartridge (G) and insert
into faucet body (H). Install nut (E)

3) Replace handle (C) and reinstall
set screw (B). Tighten set screw.
Reinstall plug button (A).

and secure collar (D).

2

D

4

E

3

G

2

H

2

3

B

C

1

A

Finish is spotting.

Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 ■ Phone: [phone] ■ Fax: [phone]

Copyright © 2018 Symmons Industries, Inc. ■ symmons.com ■ [e-mail] ■ ZV-3118 REV E ■ 110218

Troubleshooting Chart

Elements in water supply may cause

water staining on nish.

Clean nished trim area with a soft

cloth using mild soap and water or a

non-abrasive cleaner and then quickly

rinse with water.