Symmons Naru SLW-4112 Installation And Service Instructions Manual

Naru™

Widespread Lavatory Fau cet SLW-4112

Installation and Service Instructions

Model Numbers

SLW-4112

Lavatory faucet with
chrome  nish and

includes pop-up drain

Alternate Finish Codes

-STN

-PNL

-

Satin Nickel
Polished Nickel finish
Chrome (standard)

Tools & Materials

3/32"

1 2 3 4

Pipe

Sealant

Plumbers

Putty

 Need Help?

Contact Symmons customer service at

[phone], [phone]

Email: [e-mail]

Monday - Friday 8:00 am - 7:30 pm EST

 Please check Symmons website

for technical help, the latest product
information and warranty policy.

www.symmons.com/service

Quick Install Guide Naru Widespread Lavatory Faucet, SLW-4112

Step 3

Step 1

Attach faucet spout

Step 4

Step 1

Connect hoses between

valve and spout

Step 2

Attach faucet handles

Step 1

Attach control valves to sink

Step 9

Step 1

Connect supply lines
and check for leaks

Non­Removable Removable

stopper stopper

Step 5

Fasten drain body to sink

HOT

COLD

Step 8

Flush water supply lines
before attaching

(reference installation details)

Step 7

Connect lift rod, clevis strap,
pivot rod and adjust linkage

Step 6

Install stopper and pivot

rod to drain body

Installation Instructions

Installation Instructions

Caution: If replacing an older faucet ensure water supply is

turned OFF before removing. Then open faucet valves to relieve
water pressure.

Step 1 Attach control valves to sink

Deck Front View

COLD

HOT

valve

valve

screw down until
thread stops

Step 2 Attach faucet handles

Connect hoses between valve & spoutStep 4

Pipe

Sealant

Required rotational swing
clearance at base of spout is

4 inches (100 mm) minimum.

Fasten drain body to sinkStep 5

3/32" Allen

CW=OFF

at edge

front of sink

wrench

Attach faucet spoutStep 3

OFF

position

CCW=OFF

back of sink

ange washer

*

(optional)

1

PLUMBERS

PUTTY

use included ange

*

washer only when
plumbers putty is
not available

2

back

ange

beveled
washer

friction
washer

ange nut

of sink

bottom

view

Page 2

Install stopper and pivot rod to drainStep 6

Connect supply lines, check for leaksStep 9

1

non

removable

removable

easily

removable

HOT

COLD

Care of faucet fi nish

Pipe

2

Sealant

Connect lift rod and adjust linkageStep 7

Clean  nish area by using mild soap and water or non- ■
abrasive cleaner and then rinse immediately. A non-abrasive
wax may be used to preserve  nish area.

Valve cartridge replacement

3/32" Allen
wrench

1/2" (13 mm)

1 2 3

Drain body

Flush supply lines before attachingStep 8

Important

Ensure supply lines
are ushed clean
before attaching to
control valves.

HOT

COLD

Supply hoses
not included.

3 mm" Allen

wrench

Replacing handles

OFF

position

OFF

17 mm deep
socket wrench

3/32" Allen
wrench

OFF
position

OFF

Page 3

Dimensions Naru Widespread Lavatory Faucet, SLW-4112

16"(406 mm) max.

4" (102 mm) min.

2-1/4" ( 73 mm)

8"(203 mm) min.

2-1/4" dia.

(57 mm)

2-7/8"
73 mm

3-1/2"

Deck thickness

2-3/8" (60 mm) max.

2" dia.

(51 mm)

89 mm

Hole size

Hole size

1-1/4" (32 mm) min.

7/8" dia.

(21 mm)

1-3/8" (35 mm) min.
1-1/2" (38 mm) max.

1-5/8" (41 mm) max.

1/2"-14 NPSM

Flexible hose

Note: Dimensions subject to change without notice.

Parts Assembly Naru Widespread Lavatory Faucet, SLW-4112

lift rod

LN-627

spout

LN-625

faucet handle

(reference table)

mounting sleeve

valve cartridge

(reference table)

gasket

ange nut

valve body (hot)

exible hose assy

stopper

P-100N

pop-up drain

assembly

P-25LR

includes stopper

*

*

ow regulator

2.2 gpm (8.3 L/min)

(factory installed

spout base

LN-626*

gasket
retainer

retainer nut

Part Number Item

RT-411-KIT

handle assy.

1 ea. / kit

handle is used in
either hot or cold

)

locations

KN-114-EXT-KIT

HOT cartridge kit
OFF=CW

KN-113-EXT-KIT

COLD cartridge kit
OFF=CCW

LN-532
FLR-103-1.5

Valve body

FLR-103-1.0

(cold)

Note: When ordering parts for faucets with an

*

*

optional decorative nish, append appropriate
three letter nish sufx code to part numbers

1/2 inch

*

brass coupling nut

(used in rigid piping
installations only)

marked with an asterisk (*).

Ordering replacement parts:

Call Symmons customer service at [phone],
[phone] M-F 8:00 am - 7:30 pm EST or
check our website at www.symmons.com for a
list of Symmons distributors.

Replacement Parts

*

5-1/2"

(139 mm)

5"

128 mm

handle

(1)

screw

Note (1) screw requires
3/32" Allen wrench

cartridge extension

KN-113
identified
by groove

Note (2) screw requires
3mm Allen wrench

ow regulator

2.2 gpm (8.3L/min)

1.5 gpm (5.7L/min)

1.0 gpm (3.8L/min)

1-1/2"
38 mm

5/8" (15 mm)

collar

(2)

screw

2-7/8"
73 mm

1-1/8" dia.

(28 mm)

Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184
[phone], [phone]
Website:

© 2009 Symmons Industries, Inc. Printed in U.S.A. ■ ZV-589 ■ 042409

www.symmons.com

■ Fax [phone]

■ Email:

[e-mail]